Search Documents

By Jan E. Nesset, Julie Fournier, Jorge Torrealba, Colin Hardie

"Gas dispersion studies have been used to benchmark and optimize plant flotation performance for more than a decade, although this technology is not as widely in use as it likely should be based on the significant improvements that have been reported. Part of the reason may be a general lack of awareness within the industry of just what these improvements have been. This paper reviews a number of the reported case studies, groups them into categories of improvement, and draws some general conclusions. The paper will be of interest to plant engineers and technology providers seeking new approaches and tools for improving their own and clients’ processes.INTRODUCTIONThe sector of flotation hydrodynamics that is now known as gas dispersion technology, and the corresponding terminology, had its beginnings in the 1980’s and early 1990’s in the laboratories of McGill University where the students of Prof. J.A. Finch and Dr. C. Gomez conducted studies of gas holdup, superficial gas rate and water recovery on laboratory flotation columns (Laplante et al., 1983; Xu et al., 1991;, Banisi and Finch, 1994; Finch et al., 1999; Nesset, 2011). Sensors were developed for gas holdup (eg), gas rate (Jg) and bubble size (Db) distribution (Tavera et al., 1996: Finch et al., 1999; Dahlke et al., 2001; Chen at al., 2001; Hernandez-Aguilar et al, 2002, 2005). The sensor measurements were rapidly adapted for use in mechanical flotation machines in plant environments (Gomez and Finch, 2002; Gomez et al., 2003; Cooper et al, 2004; Torrealba-Vargas et al, 2004; Nesset et al., 2007). Somewhat parallel developments were being conducted by Gorain and colleagues at the University of Queensland’s JKMRC on pilot and industrial flotation machines using the McGill approach but utilizing alternate sensor designs for eg, Jg and Db (Gorain et al., 1997, 1999; Schwarz and Alexander, 2006) to link flotation kinetics to bubble surface area flux (Sb). Early industrial applications were those led by the university teams from McGill (Canada), the JKMRC (Australia) and the University of Santa Maria (Chile) at plants in North and South America, Australia, South Africa, Asia and Europe. Industrial organizations that brought the technology on-board in the early 2000’s included Teck Resources (then Teck Cominco), COREM, Vale (then Inco), Anglo American Platinum. Several of the major flotation cell manufacturers also purchased the McGill bubble viewer technology for their own equipment studies. The sensors have continued to evolve with multiple and continuous measurement of Jg (Torrealba-Vargas and Finch, 2006, Bartolacci et al., 2008), gas holdup by acoustic means (O’Keefe, 2007) and a combined Jg-Db device called the Anglo Bubble Sizer (Harbort and Schwarz, 2010). A review of the gas dispersion technology use and development have been provided by Gomez and Finch (2002), Harbort and Schwarz (2010) and Nesset (2010)."

Jan 1, 2015

By D. E. M. Plaumann, B. S. Fee, R. D. Hansen, R. R. Klimpel

"The steps from experimental curiosity through to commercial product can be slow and tortuous in spite of the quality of the technological advances offered by the new development. Data generation and interpretation need to be done in lab tests as well as full-scale evaluations and, in each, the advantages of the new reagent must be clearly identifiable and measurable.The Dow Chemical Company has patented a novel new collector for the flotation of zinc. Fl (2-hexylthioethylamine hydrochloride) has several unique structural features that suggest atypical mechanisms for zinc collection. Laboratory data have demonstrated significant flexibility with respect to grade and recovery balance at dosages lower than those typically used for xanthates.In mill trials, the same phenomanon is evident - the choice between high grade and high recovery allows one to select the desired quality of zinc concentrate. One trial in particular was run over a three month timeframe and Fl gave improvements in recovery of 2.5% and a reduction in lead levels with less than 0.5% loss in grade. The dosages of other reagents in the flotation circuit were also reduced.Data demonstrating improved recovery and grade in lab trials will be discussed. Extensive data from the mill trial will illustrate how Fl works in both rougher and cleaner circuits."

Jan 1, 1990

By Stephen L. Chryssoulis, Stamen Dimov

"Preg-robbing has been known for many years, where increased losses are suffered because dissolved gold is removed from solution by adsorption onto carbonaceous matter. In direct cyanidation circuits it is reasonable to conclude that the preg-robbed gold is either in a gold cyanide [Au(CN) - 2, AuCN] or metallic [Au°] form. However, in circuits with a pre-oxidation step possibilities increase and multiply even further because of water recycle streams containing apparent and not-so-apparent gold ligands. It is in these circuits where speciation of sorbed gold, i.e. the identification of the gold compound, is useful. The importance arises from the fact that proper identification of the sorbed gold species can be used to determine how, when, where and why gold was removed from solution, thereby identifying the exact cause of the problem and providing clues as to how it may be rectified.INTRODUCTIONTo the best of our knowledge, this is the first attempt ever to speciate gold preg-robbed by carbonaceous matter using a surface sensitive microbeam technique. This approach enables the direct determination of gold species sorbed on carbonaceous particulates, opening an entirely new field in the understanding of the chemistry of gold sorption on carbon. The reasoning behind this effort was to add to the current knowledge of the detrimental effect chloride ions have on gold recovery by the pressure oxidation and in particular why in the ensuing CIL step, gold is not being desorbed from the surface of the carbonaceous particles (Table 1)."

Jan 1, 2004

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton

"Hydrophobic polystyrene nanoparticle suspensions were evaluated as potential flotation collectors for pentlandite. Experiments involving both clean model mineral suspensions and complex ultramafic nickel ores confirmed that conventional water-soluble molecular flotation collectors such as xanthate could be partially or completely replaced by hydrophobic nanoparticle flotation collectors. The ability of nanoparticles to induce flotation was demonstrated by floating hydrophilic, negatively charged glass beads with cationic polystyrene nanoparticle collectors. Electrostatic attraction promoted the spontaneous deposition of the nanoparticles on the glass surfaces raising the effective contact angle sufficiently high to promote the adhesion of beads to air bubbles. As little as 10% coverage of the bead surfaces with our most effective nanoparticles could promote high flotation efficiencies, whereas conventional small molecular flotation collector requires ~ 20% or higher coverage for a good recovery. Surface functionalized nanoparticles enhanced the ability for nanoparticle collectors to selectively deposit onto surfaces of the desired mineral particles in the presence of gangue. For example, poly (styrene-co-vinylimidazole) nanoparticles were designed to selectively deposit onto nickel mineral (pentlandite) in the presence of Mg/Si slime. Flotation tests of ultramafic nickel ores at Vale with these nanoparticle collectors have shown improvements in both pentlandite recovery and selectivity. On-going work includes attempts to identify specific applications where nanoparticle flotation collectors might be cost effective.INTRODUCTION Most mineral processing operations include multiple stages of froth flotation to concentrate and isolate the desired product. Before flotation, chemical collectors are routinely added to ground ore slurries, selectively binding to mineral-rich particles, increasing their hydrophobicity thus promoting selective flotation. (Fuerstenau, Jameson, & Yoon, 2007) Conventional collectors are surfactants with a short hydrocarbon tail and a head group, such as xanthate. A typical conventional collector is potassium amyl xanthate (PAX), which is a small molecule with an extended molecular length of about 1 nm. Critical characteristics of a good collector include the ability to selectively adsorb onto desired mineral surfaces and to lower the water/mineral surface energy. Despite the extensive role of flotation in mineral processing, some ores are difficult to process by flotation. For example, ultramafic nickel sulfide ore containing both valuable pentlandite and large quantities of unwanted Mg/Si slime [primarily serpentine, (MgFe)3Si2O5(OH)4] responds poorly to flotation. (Mani, Xu, Quinn, & Stratton-Crawley, 1997) Fibrous hydrophilic Mg/Si slime usually masks the surface of pentlandite (known as “slime coating”) due to electrostatic interaction (Edwards, Kipkie, & Agar, 1980) and dramatically depresses pentlandite flotation. Consequently, new approaches are required for processing these difficult ores."

Jan 1, 2012

By H. Warren Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomic. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

May 1, 2002

Block caving is an underground mining method for the profitable extraction of massive, low-grade orebodies. Lately, it has become the mining method of choice, for many mining companies, because of depleted high-grade orebodies, and declining metal market prices. Block cave mining, however, still faces several challenges. Lack of access to the cave remains a major issue in understanding the rockmass response to mining for method optimisation. Improving our understanding of the rockmass response to caving will lead to safer and more productive operations. Combining large datasets from multiple sources with virtual reality scientific visualisation (VRSV) is a viable alternative to understanding complex cave behaviour without access to the cave. This is achieved using immersive environments with the ability to view complex multi-dimensional data (beyond 3D) graphically. VRSV offers a unique platform where it becomes possible to immerse the multi-disciplinary experts, and/or management team, in a virtual mine environment for quick decision making and fast resolution to conflicting conclusions. The underground mining system is complex due to multiple interrelating factors such as geology, excavation geometries, stress and time. Block caving is even more complex than most underground mining methods due to the network of tunnels required, and the use of induced stress, among others. As a consequence of the complexity in the block caving environment, it is vital that the mining system is analysed holistically, as a system, rather than optimizing individual factors one at a time. This paper presents a customised software module developed for use in the Advanced Visualisation Interactive Environment (AVIE) at The University of New South Wales (UNSW), Australia, to enable VRSV investigation into block cave mining systems (BCMS). This approach has the potential to provide a better understanding of the effect of time in in rock engineering, which has proven to be an important factor in hard rock mines (Ma & Daemen, 2006; Malan et al., 1997; Suorineni, 2010) but never validated. This work back analyses the early undercutting phase of a case study block caving operation with the view to understanding time/sequence effects. There is evidence that heterogeneous rockmass time-dependent behaviour governs the seismic response of the rockmass following undercut developments.

Jan 1, 2015

In order to maintain a production rate of 6,000 tonnes per day from underground at the Williams Operating Corporation, two independent mining areas were required which created a long narrow sill pillar between them. During initial mining of the sill pillar there were a number of significant ground falls [LeBlanc and Murdoch, 2000] and in March 1999, with no active mining ongoing in the sill pillar area, a rockburst of magnitude 3.0 Nuttli occurred. Extensive ground support was designed and installed to withstand events of similar magnitude [Bawden and Jones, 2002]. A mine wide microseismic system was installed to monitor mine induced seismic behaviour over the entire mine. The area most directly affected by the 1999 rockburst was rehabilitated using a highly ductile support design. Along with microseismic instrumentation, the areas were instrumented using conventional SMART Cables and SMART MPBX?s. Subsequent to this, the area was impacted by a large number of high magnitude seismic events [magnitudes between 1.7 and 3.5 Nuttli]. The ground support performed very well during these events, providing confidence in the mine?s ability to control the ground under severe rockburst conditions. Analyses of microseismic and conventional instrumentation, combined with numerical analyses of sequence alternatives, were used to develop an optimal mining strategy for the sill pillar area. The selected strategy involved utilization of instrumentation data and calibrated model results to analyze yield zones in the sill. The analyzed ?yielded? zones were assessed to be low seismic risk. Initial mining in the sill was then concentrated in these low risk areas, with the objective of further concentrating stress into the remaining seismically active area, in order to induce ultimate failure of the sill. Continuing large magnitude seismicity and resulting damage in the remaining ?high seismic risk? area, led to abandoning a second portion of the footwall access and the strategic decision to extract a stope near the centre of this zone in order to force final failure of the sill pillar. During execution of this plan two large magnitude seismic events occurred resulting in destressing and final failure of the remaining sill pillar. The paper provides a detailed description of this ?strategic mine sequence driven self-destressing process? and the implications to final extraction planning in this area of the mine.

Apr 1, 2005

By S. Kelebek, C. Gibson, M. Aghamirian

"Global niobium production is currently dominated by three operating mines, Araxá and Catalão in Brazil, and Niobec in Canada. Although over 90% of the world’s niobium is mined and processed in Brazil, a number of high grade niobium deposits exist worldwide. The advancement of these deposits depends largely on the development of operable beneficiation flowsheets. Pyrochlore, the primary niobium bearing mineral, is typically upgraded by flotation with amine collectors at acidic pH, and often includes a reverse gangue flotation stage prior to pyrochlore flotation. Challenges related to the flotation of niobium ores include complicated flowsheets which require pulp pH adjustment from alkaline to highly acidic conditions, difficulty recovering fine grained pyrochlore, producing concentrates that meet specifications, and minimizing the losses to reverse pre-flotation gangue concentrates, slimes, and tailings. The specific flotation challenges associated with different niobium ores are discussed. In some cases, the use of alternate flotation reagents and flowsheets are required to achieve reasonable gangue rejection and maximize recovery, particularly of very fine pyrochlore grains.INTRODUCTIONNiobium is a transition metal primarily found in the oxide minerals pyrochlore (Ca,Na)2Nb2O6(OH,F) and columbite (Fe,Mn)Nb2O6. After physical upgrading, pyrochlore is converted into a ferroniobium product which is largely used in the production of high strength low-alloy steel. Today’s niobium market is dominated by the Companhia Brasileira de Metalurgia e Mineração, whose Araxá operation produces over 80% of the world’s niobium. There are two smaller operations, Niobec in Canada, and Catalão in Brazil, which account for the remaining production (U.S. Geological Survey, 2013).A number of niobium deposits exist globally, their advancement dependent on the development of operable beneficiation flowsheets. Pyrochlore, the predominant niobium bearing mineral, is commonly upgraded by flotation with cationic amine collectors in acidic pulp conditions. However, many niobium ores do not respond to this typical flowsheet because they are either highly refractory or niobium deports to other minerals such as columbite, ilmenite and rutile, which are not as responsive to this reagent scheme (Bulatovic, 2010). Other reagents, such as alkyl hydroxamic acid, have been studied extensively and while promising, are not without their own inherent issues including lack of selectivity over iron oxide minerals, and high addition rates (Ni & Liu, 2012; Gorlovskii, Eropkiny, Koval, Strelstin, Khobotova, & Shtchukina, 1968; Gorlovskii, Khobatova, & Shtchukina, 1966).It is the aim of this report to highlight the challenges associated with the physical upgrading of niobium minerals through examination of the flotation behavior of two different ore systems. In order to overcome these challenges it is important to thoroughly understand the limitations of typical flowsheets/reagent schemes currently employed in operation."

Jan 1, 2015

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By Quin Dennis

Process Optimization ?What is it really? It is NOT ?a larger fan to increase draft through a process ?a larger pump on a wet circuit ?a wider conveyor belt for solid materials ?a larger feed elevator into or out of a process These relieve individual constraints ??bottlenecks??and allow operation to the next constraint in the process ?It is also NOT about automating the operator ?which captures consistency but is not continuous optimization

Nov 1, 2011

By M. R. Dion, K. Frenette, R. K. Jonas, S. Simard, F. Robichaud

"In 2011, a site study indicated that the application of Honeywell’s Multivariable Predictive Control Technology (MPC) to the Goldex processing facility would provide significant opportunities for improvement. Grinding MPC was implemented in the SAG Mill in June 2015. This pilot application, called Phase 1, featured one of the first Multivariable Predictive Controllers to be installed in a Canadian mineral processing plant. Since the implementation of MPC, gold recovery from the gravity circuit has increased. MPC contributed to a decrease in flotation feed particle size (120 to 112 µm) and an increase in the SAG feed tonnage (8.5% increase). MPC also increased and stabilized the % solids of the SAG feed, which can have an impact on cost reduction (mechanical maintenance). Additionally, MPC increased productivity, providing grinding operators with more time to perform other tasks. Further anticipated benefits include the standardization of the grinding circuit operation from one team to the next, thereby minimizing circuit disturbances resulting from different operating philosophies. This paper will discuss the advanced control project development and justification, the technology and rapid implementation process, the performance results and the benefits obtained.IntroductionGoldex is an underground mine located near Val-d’Or that is owned and operated by Agnico Eagle Mines Limited (AEM). Between 2008 and 2011, mining focused on the Goldex Extension Zone (GEZ). In 2011, the project was halted due to geotechnical problems; operations ceased until late 2013. Goldex operations resumed in September 2013 with the M and E zones, for which there were 0.7M gold ounces of proven and probable reserves, 2.1M ounces of measured and indicated resources and 1.2M ounces of inferred resources, totalizing 4M ounces. Life expectancy was extended until 2024."

Jan 1, 2017

By Roberto Busato Belger

- Fertilizer Business Overview - Supply -Demand Balance in the World - Supply -Demand Balance in Brazil - Brazilian Market Growth Opportunities - Fosfertil Operations - Fosfertil Expansion Plan - Salitre Project - Project Characteristics - Technical Challenges and Solutions - Technical Support Studies Conclusions

May 1, 2010

By K. Nasrallah

"The Dumont deposit is a large (1,179 Mt proven and probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the project from a scoping study in 2010 through to completing the feasibility study in July 2013.The Dumont deposit in a nickel deposit with the recoverable nickel contained in three minerals; pentlandite, haezlewoodite and awaruite. The minerals are recovered by a combination of flotation and magnetic separation. Over the course of the studies many flowsheet design decisions and changes were made. This paper outlines an overview of the project, flowsheet design including the comminution circuit, desliming and awaruite recovery. The overall resulting flowsheet that was used for the feasibility study is then presented along with the confirmatory locked cycle testing that showed the feasibility design basis was able to produce the predicted concentrate grade and recovery.IntroductionRoyal Nickel Corporation (RNC) is a mineral resource company headquartered in Toronto, Canada, primarily focused on the exploration, evaluation, development and acquisition of base metal and platinum group metal properties. RNC's principal asset is the Dumont Nickel project (Dumont project) located in the established Abitibi mining camp, 25 km northwest of Amos, Quebec. RNC acquired a 100% interest in the Dumont property in 2007. The mineral claims covering the Dumont deposit are currently held 98% by RNC and 2% by Ressources Québec.The Dumont project is located in the province of Quebec in the municipalities of Launay and Trécesson approximately 25 km by road northwest of the city of Amos, 60 km northeast of the industrial and mining city of Rouyn-Noranda and 70 km northwest of the city of Val d’Or."

Jan 1, 2016

Many mines in Canada, the US and S. Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due the excessive weight. It has been suggested (DeLorme, 2000), that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm(1 ¾ in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg(10 ton) skip may exceed the safety factor of the rope. To improve on the current understanding of the mechanical behavior of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modeling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca 1995b) is used to simulate the structural behavior of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modeling on the wire rope will be discussed.

May 1, 2002

By Dave Rose, David G. Meadows, Mike Westendorf

"Copper Mountain’s concentrator was commissioned in May 2011. The circuit consists of a 34’ x 20’ EGL SAG mill, a Raptor 900 pebble crusher and two 24’ x 39’6” ball mills. Each mill is equipped with a 2 x 8500 HP dual pinion drive system. The plant was designed to process 1585 mtph of SAG feed. From startup, the mill struggled to meet the required production rates. Over time, a major initiative that involved blasting and fragmentation, optimization of the SAG mill in terms of discharge grates, ball size and slurry density, and operation of up to three mobile pre-crushing plants resulted in significant increases in throughput. In parallel, a number of modeling tools, including JK SimMet, were run based on plant benchmarking exercises. Samples collected at the mine site during ramp up confirmed the very competent nature of the ore with drop weight - A*b values of less than 24 being recorded on a variety of plant feeds and lithologies. After due consideration including demonstration of proof of concept, a new pre-crushing circuit incorporating an XL2000 cone crusher and associated screening equipment was designed, constructed and commissioned at the site in August 2014. This paper reviews the history of the original circuit design, the various optimization steps taken and impacts, together with the final pre-crushing circuit and net results.IntroductionThe Copper Mountain Mine is located approximately 20 km south of Princeton, British Columbia, Canada (refer to Figure 1). The region has a long history of copper mining dating back to 1923. The Copper Mountain camp occurs in the 'eastern volcanic belt' of the Nicola Group (Monger, 1989). It is an alkali copper-gold deposit in which the volcanic strata are intruded by early Jurassic dykes, sills, irregular plugs and zoned plutons (Woodsworth et al., 1992). The stratified rocks are relatively fresh with slight metamorphism in the local contact regions."

Jan 1, 2016

By M. Lahtinen, P. Latostenmaa, I. Kojo, E. Peuraniemi, M. Lindgren, S. Jyrkönen, M. Jåfs

The year 2019 marks the 70th anniversary of Flash Smelting. The technology was operated on industrial scale for the first time at the Outokumpu Harjavalta copper smelter in Finland in 1949. Since then Flash Smelting technology, now owned and developed by Outotec Oyj and the first plant, now owned by Boliden Harjavalta Oy, have been evolving throughout history by optimizing the process for various feeds and raw-materials, as well as through developing the equipment and operating practices. Even though sustainability was not a popular theme during the first days of Flash Smelting, it has still been the key principle in guiding the development. This is well proven by the wide adoption of Flash Smelting for the processing of copper and nickel concentrates, mostly due to its ability to fulfil the economic and resource efficiency criteria demanded by its operators. This paper describes the history and improvements of the Outotec® Flash Smelting process by looking into the early days of operation and how the development of the process and equipment has taken place over time as a joint effort between the technology provider and the users of the technology. INTRODUCTION In the 1940s, Outokumpu Oy refined the concentrate produced in the Outokumpu mine into metallic copper initially in Imatra, and later from 1945 to 1949 in Harjavalta, based on the most modern electrical melting process of the world at that time. After the war, Finland lost a significant part of its hydropower production, and due to the increasing use of electricity, the availability of electricity weakened, and the price rose. To maintain Outokumpu's profitability, it was forced to look for a melting solution that was not based on electricity.

Jan 1, 2019

By Mark Ferra

Flotation is used in mining to produce concentrates of copper, gold and several other valuable ores. In 2017, a copper mine near Globe, Arizona improved their rougher cells productivity using technically advanced electro-hydraulic actuators in the flotation process by enabling excellent tank pulp level process stability. The new actuators controlled the dart valve position to allow pulp to leave the cell. Tank cell pulp level can change due to feed and discharge fluctuations from neighboring tanks. When traditional pneumatic actuators are used, they have sluggish response times and overshoot due to the inherent physical property of air being compressible. Electro-hydraulic actuators have the benefit of hydraulic stiffness to deliver accurate and repeatable (0.1%) dart valve positioning. The froth layer has more opportunity time to maximize mass transfer into the launderer. The results are an increase in copper recovery by 2-4%. INTRODUCTION In 2013 there was an international flotation technical conference well attended by respected flotation specialists for both mining companies and academia. During the technical session a leading metallurgist was discussing pulp level measurement and said that when he was on the cell deck he stated, pneumatic actuators air cylinders stroking up and down. The presenter then claimed with confidence that "I listened to actuator move so the pulp level in the tank was being controlled!" No one questioned his assumption and I can assert that the audience was quite technical and not shy in their critiques of speakers. The flotation community simply believed that the existing pneumatic technology was enough with no alternative. Having a stable flotation cell pulp level is critical to effective copper recovery. Controlling pulp levels in flotation cells is a complex task that includes modulating dart valves in each cell. The use of REXA Electraulic actuators will decrease the process dead time and maintain froth height in a controlled manner, especially from pulp slurry volume fluctuations from neighboring cells. By reducing flotation cell pulp level tank height variation, a copper mine in Arizona has realized a 2-4% recovery improvement by increasing the froth transfer to the launderers in the rougher cell circuits compared to pneumatic actuators. This paper examines the benefits of using an electro-hydraulic actuator to ensure proper pulp level control and reduce the process operational cost. It will focus on actuator positioning the dart valves to maintain pulp level setpoint at a copper mine in Arizona.

Jan 1, 2019

By Martin Nevens

"In 1998, the Iron Ore Company of Canada initiated an aggressive program to improve the performance of its Carol Lake Concentrator located in Labrador City, Newfoundland. This program was termed the Concentrator Upgrade Program. The Concentrator Upgrade Program was a group of initiatives developed with the common goal of improving the overall process and operations of the IOCC Carol Lake Concentrator. The main goal of the program was to increase the annual production capacity of the concentrator from 18.0 million tomes to 21.6 million tomes. This gain in capacity was to be done mainly through improvements in process iron recovery. The target iron recovery value was 80+% versus a historical value of 70%. This improvement in iron recovery would translate to a natural weight recovery improvement from 44% to 50%.The Concentrator Upgrade Program provided the first opportunity in 30 years to make fimdamental changes to the concentrator flowsheet. To accomplish this, several pilot plants were built to evaluate new circuits. AAer 2 years, a new flowsheet was selected for the primary gravity separation circuit and the magnetite circuit. The centrepiece of the new flowsheet was the introduction of Hindered Settling Separators to the metallurgical process.The Concentrator Upgrade Program has since proceeded into detailed engineering and, as of February 2001, construction. The first one of IOCC’s 3 primary AG Mills (Mill 11) has been converted to the new flowsheet at the time of writing and is in the throes of commissioning. This paper will review the flowsheet development program in the pilot plant for the gravity separation circuit and examine the overall benefits to the operation of the IOCC Carol Lake Concentrator."

Jan 1, 2002

By A. Taylor, J. Shelegey, H. Sullivan, J. Doucet

"Historically, performance at Vale’s Clarabelle Mill was measured by Mill throughput and Mill recovery. After the economic collapse in 2008, a series of reviews were performed to drive improvements in business efficiency. These identified that product quality (e.g., concentrate grade, variability in concentrate grade) had a profound impact on downstream processes and suggested that improved control of these parameters would generate the greatest value for the customer (the Copper Cliff Smelter) and the company (Vale). Consequently, a movement was initiated to transform the Mill operating philosophy to consider customer needs as paramount. Systems and strategies used to drive the transformation are described. In 2011, an unexpected furnace failure resulted in decreased capacity at the Copper Cliff Smelter. In response, a two-stage change in production strategy was developed at Clarabelle. The first stage was to modify the ore blend feeding Clarabelle so that the concentrate grade could be significantly increased with minimal impact on recovery. The second stage was a circuit modification to ensure the elevated concentrate grade could be sustained. Execution of the first stage was complete five days after the failure and the second stage was complete within 10 weeks. Steps involved in each stage are outlined and the overall benefits are presented.INTRODUCTION Clarabelle Mill is located in Copper Cliff, Ontario, Canada (approximately 350 km north of Toronto). The Mill treats copper (Cu) and nickel (Ni) sulphide ores. The primary diluents are pyrrhotite (Po) and non sulphide gangue rock (Rk). The process description of the circuits at Clarabelle is documented in the paper by Taylor, Doucet, Blanchette, Barrette & Lawson (2012) in this Proceedings and will not be repeated. The Mill treats ore containing Cu, Ni and platinum group elements (PGE’s) and produces two concentrates; a Cu concentrate and a bulk Cu/ Ni Concentrate (referred to as nickel concentrate). The Cu concentrate is sold to market while the Ni concentrate is thickened at the Mill and pumped to Vale’s smelter complex in Copper Cliff Ontario for further processing. Since commissioning in 1971, Clarabelle Mill has undergone many circuit changes to suit the changing needs and wants of our customers, both internal and external. The Mill processes ores of varying quality, based on mineralogy and size and until 2009 the Mill daily performance was primarily based on throughput. The second key performance indicator (KPI) of “good” or “bad” performance was quality of the concentrate and third; Mill metal recoveries. There were other plant level KPIs such as flotation feed grind size, slurry densities and mass flows to the separation circuit, but for the most part each day was good or bad depending on how many tons were processed through the Mill."

Jan 1, 2012

By Michael Godard, Peter Cleyle

"Suncor Energy’s Project Millennium increased oilsands production capacity by an additional 95,000 barrels per day to its present level of 225,000 barrels per day. This massive venture included an expanded Mine, new Extraction and Upgrading facilities, as well as, steam and utilities infrastructuresIn the Primary Extraction process, removal of the bitumen from the oil sand begins with slurry preparation and is followed by primary , secondary and tertiary separation processes. The final cleaning step of the bitumen froth is the Secondary Extraction process, that removes residual water, mineral and solids to produce a clean diluted bitumen suitable for Upgrader feedstock.This paper will review the flowsheet of the Millennium Primary Extraction facility, from its recent commissioning through the ramp up to design production rates. In addition, new technologies in the Primary Extraction flowsheet will be reviewed.INTRODUCTIONAs conventional supplies of oil and gas are depleted in Canada, the Athabasca oil sands industry of Alberta becomes an increasingly important source of energy. Today, high quality crude from Alberta’s oil sands accounts for roughly 30% of Canada’s daily petroleum production. According to government projections, over the next 7 years, oil sands production is expected to more then double, and by 2010 more than half of Canada’s crude oil is expected to come from the oil sands.Oil sands deposits consist of a layer of sand saturated with bitumen covered by a muskeg overburden and underlain by silt and clay. The oil sand is mined where the overburden is economical to remove, typically less than thirty meters thick. The Athabasca oil sand deposits around Fort McMurrray is ideal for mining. Bitumen can be described as a diverse collection of hydrocarbons, organosulfur, and nitrogen compounds."

Jan 1, 2004