Search Documents

By Abdelkabir Maqsoud

Different management options and rehabilitation strategies are available for mine wastes that produce acid mine drainage (AMD). One of them consists in building a cover with capillary barrier effects (CCBE) on the tailings to limit the availability of oxygen, an essential component of the chemical reactions leading to the generation of AMD. Prior to cover construction, a monitoring strategy must be established to evaluate the response and performance of the cover system. The key parameters to monitor should include matric suction and volumetric water content in the CCBE, oxygen flux (and/or oxygen concentration) through and below the cover, and the main meteorological parameters for the impoundment. In this paper, different techniques available to measure the targeted parameters are described and their main properties are given. Recommendations (based on existing cases) on the location and the number of monitoring stations and on the measurement frequency for each monitored parameter are also proposed.

May 1, 2007

By C. Hilgendorf, J. Gingerich, J. R. Boniwell, M. Drouin, D. David on, J. Boldy

The initial discovery of gold in the Eastmain River area, 310 km northeast of Chibougamau, was made by Placer Development Limited in 1970. This discovery resulted from the drill testing of an airborne E .M. Target located in an area of extensive glacial overburden, within an unexplored Archean greens tone belt considered prospective for base metal deposits. Intermittent exploration by another company between 1973-1977 failed to obtain promising results and the existing claims were allowed to lapse. In 1981, Placer reactivated the project and initiated intensive exploration during the next two years which included aerial E .M. surveys, claim staking, ground E .M. and magnetic surveys, geological mapping, diamond drilling and attendant borehole P,E.M. surveys. Beginning in 1983, exploration has been conducted on a joint venture basis with Eldor Resources Limited, The greenstone belt under investigation has an arcuate distribution pattern relative to a centrally located granitic core. Occurrences of gold mineralization defined to date are located to the south of the granite along a strike length of 7 km, and appear to be restricted to the lowermost of two mafic volcanic cycles. This lower cycle is dominated by basaltic flows with subordinate rhyolitic flows and pyroclas ties. Concordant, variably magnetic, massive to talcose ultramafic units occur towards the stratigraphic top of the lower mafic volcanic cycle and appear to crudely define areas considered prospective for gold on a regional bases. Economic interest in centered on a s tratabound, siliceous, sulphide-bearing unit hosted in a 15- 25 metre thick sequence of rhyolite tuffs, basalts and intercalated ultramafics, The siliceous ore bearing unit ( interpreted as a recrystallized chert) contains from 10%-30% pyrrhotite and pyrite with subordinate chalcopyri te and minor sphaleri te. Alteration is characterized by mica development, silicification and carbonatization. Garnets are also occasionally present in close proximity to the ore horizon. The sequence is south facing, and overturned to the northeast at 35°-55°. Explora tory drilling in the vicinity of two conductive targets has been on 100 metre centres along a 1 km strike length of the prospective sequence. To the end of 1983, two ore zones (A and B) have been partially drill tested with estimated indicated and inferred geological reserves of 1 million tonnes grading 11.7 g/t gold , 14.7 g/t silver and 0.26% copper. The system is open at depth. This discovery is the result of the effective integration of geophysics and geology with contributions by many over a long period of time. Key events that can be emphasized are: ( 1) initial area selection of a remote greenstone belt in 1969 - albeit for base metal deposits , (2) utilization of an airborne E .M. system which successfully targeted the A Zone in 1970 , (3) the timely reactivation of the project in 1981 and the subsequent recognition that the original discovery represented a sulphide bearing stratabound horizon with implicit volcanogenic connotations , (4) the intensive effort in 1982-83 deploying aerial and ground geophysics coupled to volcanogenic concepts of ore distribution which resulted in the discovery of the B and C Zones in 1982, and (5) the integration of downhole P . E.M. surveys and geology to successfully delineate ore at increasing depths . To the end of 1983 , $2.6 million has been expended, and it is hoped that continued effort will result in the eventual delineation of an economically viable ore deposit for the joint venture partners .

Jan 1, 1984

By André van Wageningen

Since the beginning of this century Boliden Mineral and Atlas Copco have worked together in stages on improving the accuracy and quality of drilling. Navigation of the drill rigs with IREDES has been in use in the Boliden mines for several years. Recently the capability of the system has extended with map navigation to more accurately follow the ore in cut&fill mines. The system allows for changes on the individual round level to follow the ore without changing the whole design for the heading. Those changes are done in a CAD-system and remove the need for face markings and will allow for even better accuracy in both height and wall position. All the information between the CAD-system and the drill rigs is exchanged using the IREDES standard. This paper describes the workflow and the use of the IREDES standard.

Oct 1, 2009

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By M. Nagamori, A. J. Plumpton

"Commercial HCl-leaching of magnesite and serpentine yields highly concentrated aqueous solutions containing 25 mass % to 33 mass % MgCl2. The partial molar enthalpies and heat capacities, the ionic activities of Mg2+ and Cl–, and the Raoultian activity of H2O have been assessed for the concentrated MgCl2-H2O solutions at temperatures of 348 to 373 K. These thermodynamic data are used to calculate the pH of aqueous MgCl2 solutions saturated with a Mg-bearing mineral such as magnesite, serpentine, brucite, forsterite, enstatite or talc. On the basis of these thermodynamic data, technico-economic aspects are discussed as to neutralization with pulverized MgCO3, water evaporation from the MgCl2 solutions, and ore composition including such minor constituents as CaCO3, FeCO3 and Fe3O4. IntroductionA major magnesium electrolytic reduction plant operates in Quebec, where another will begin its production in the year 2000. One uses imported magnesite ore as raw material, while the other will utilize local asbestos tailings (serpentine). Both processes produce a concentrated salt solution of 25 mass % to 33 mass % MgCl2 by leaching the ore with concentrated hydrochloric acid. Thus, the two processes differ mainly in the HCl-leach and related operations. After the HCl-leach of the ore, the serpentine process yields about 25 times more wet cake to filter and wash than the magnesite counterpart. A comparative cost-engineering study with respect to slurry filtration and cake washing has been published elsewhere (Blackburn and Nagamori, 1994). By contrast, the present study considers the thermodynamics and technicoeconomics of the HCl-leach itself for both ores."

Jan 1, 1999

By Frederick W. Breaks, Andrew G. Tindle, Julie B. Selway

"Abstract - Rare-element pegmatites may host several economic commodities, such as tantalum (Taoxide minerals), tin (cassiterite), lithium (ceramic-grade spodumene and petalite), and cesium (pollucite). Key geological features that are common to pegmatites in the Superior province of Ontario and Manitoba, Canada, and in other large tantalum deposits worldwide, can be used in exploration.An exploration project for rare-element pegmatites should begin with an examination of a regional geology map. Rare-element pegmatites occur along large regional-scale faults in greenschist and amphibolite facies metamorphic terranes. They are typically hosted by mafic metavolcanic or metasedimentary rocks, and are located near peraluminous granite plutons (A/CNK > 1.0). Once a peraluminous granite pluton has been identified, then the next step is to determine if the pluton is barren or fertile. Fertile granites have elevated rare element contents, Mg/Li ratio < 10, and Nb/Ta ratio < 8. They commonly contain blocky K-feldspar and green muscovite. Key fractionation indicators can be plotted on a map of the fertile granite pluton to determine the fractionation direction: presence of tourmaline, beryl, and ferrocolumbite; Mn content in garnet; Rb content in bulk K-feldspar; and Mg/Li and Nb/Ta ratios in bulk granite samples. Pegmatite dikes with the most economic potential for Li-Cs-Ta deposits occur the greatest distance (up to 10 km) from the parent granite.Metasomatized host rocks are an indication of a nearby rare-element pegmatite. Metasomatic aureoles can be identified by their geochemistry: elevated Li, Rb, Cs, B, and F contents; and by their mineralogy: presence of tourmaline, (Rb, Cs)-enriched biotite, holmquistite, muscovite, and rarely garnet.Once a pegmatite dike has been located, the next step is to assess its potential to contain Ta mineralization. Pegmatites with the highest degree of fractionation (and thus the most economic potential for Li-Cs-Ta) contain blocky K-feldspar with >3,000 ppm Rb, K/Rb < 30, and >100 ppm Cs; and coarsegrained green muscovite with >2,000 ppm Li, >10,000 ppm Rb, >500 ppm Cs, and >65 ppm Ta. Pegmatites with Ta mineralization usually contain Li-rich minerals (e.g., spodumene, petalite, lepidolite, elbaite, amblygonite, and lithiophilite) and may contain Cs-rich minerals (e.g., pollucite, Cs-rich beryl). The ore minerals of Ta are commonly manganotantalite, manganocolumbite, wodginite, and microlite; Ta-rich cassiterite is also commonly present. Tantalum mineralization tends to occur in albitic aplite, mica-rich (lepidolite, cleavelandite ± lepidolite), and spodumene/petalite pegmatite zones."

Jan 1, 2005

CORPORATE SOCIAL RESPONSIBILITY CSR is about how companies manage the business processes to produce an overall positive impact on society. - Indentured work, sexual slavery, fair trade, organic growing, business ethics, environmental issues, ?Right to know -Right to decide?, AIDS activism, civil society - Balancing stakeholder issues - Government responses Who are the bad guys? Where are the threats?

May 1, 2010

By R. Laplante, P. Radziszewski, P. De Ciccio

"Predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case. Wear conditions vary with geological formations and compositions. The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American drilling campaigns. Simulation results allow the definition of simple graphical tools that permit the estimation of the potential drill depth remaining on a given drill rod string. IntroductionWear, in many industrial processes, is an undesired phenomenon for which enormous efforts are made to control, if not eliminate. However, wear, in many other cases, is an intrinsic phenomenon of the given process. In such cases, predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case where abrasive conditions vary with geological formations and compositions.A number of studies have been published on drill rod wear especially with regards to the petroleum industry over the last thirty years (Lewis, 1968; Rollins, 1968; Smith, 1978; White 1978; Rowe and Wilson, 1981; Cheng, 1982; Eustes, 1986; Dudman et al., 1989; Besaisow et al., 1990). Of these, most studies covered management techniques (Rollins, 1968; Smith, 1978; White, 1978; Rowe and Wilson, 1981; Besaisow et al., 1990) and some described case histories (Cheng, 1982; Eustes, 1986; Dudman et al., 1989). However, little (Lewis, 1968) was presented that could aid in predicting wear in the particular case of diamond drilling in the metal mining industry.The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate diamond drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American diamond drilling campaigns."

Jan 1, 2002

The Beginning ! The status quo simply isn?t sustainable ! Our social license is at risk ! The bar keeps rising ? We must improve our performance, both operational and social ? We must improve stakeholder judgement of our industry by taking action collectively Implementing TSM " TSM Guiding Principles " Performance Indicators " Crisis communications " External Outreach " Tailings management " Energy management " Performance manuals, guides " Reporting " Communities of Interest Advisory Panel

May 1, 2004

By Unknown

We are indebted to the Consolidated Mining and Smelting Company of Canada Limited for the several pictures in this issue showing the progress made in new construction at Tadanac and at Bonnington Falls, B.C. Plate No. 1 shows the down-stream side of the No. 1 hydro-electric station of the West Kootenay Power and Light Co. Limited at Bonnington Falls, on the Kootenay river, at which 17,500 k.v.a. will be developed to meet the requirements of the enlarged zinc and lead refineries at Tadanac. The generators, exciters and switch apparatus were supplied by the Canadian General Electric Company and the step-up transformers by the Canadian Westinghouse Company Limited. The plant throughout was designed, manufactured and erected by Canadians. Plate No. 2 shows the casting room of the new lead-plant and plate No. 3 the new tank-room of the electrolytic lead refinery at Tadanac. These additions will increase the capacity of the lead refinery by some 150 tons daily. The extensions also include practically doubling the zinc plant, and the gold and silver refineries. With the exception of the new stack, all designing construction and installation of the various plants is being done by the Company&apos;s own employees at Tadanac. Plate No. 4 shows the progress made in the construction of the new reinforced concrete stack at Tadanac. This stack, of 21 feet inside diameter at the top, will be brick lined and when completed will rise 400 feet above its foundations: the tallest of its kind in the world. The construction is in charge of the Rust Engineering Company of Pittsburgh, Pa. Plate No. 5 is a panorama of the Tadanac smelters and refineries. The photograph was taken from the roof of the lead smelter and gives an excellent idea of the size of the plant and its surroundings. Tadanac produces electrolytic lead, zinc and copper and fine gold and silver. During 1924 the company treated 1,333,523 tons of ore and produced: 161,400,- 769 pounds of lead; 92,197,824 pounds of zinc; l,382,750pounds of copper; 4,074,044 ounces of silver, and 26,976 ounces of gold.

Jan 1, 1925

By David Berberick

"Hecla Limited’s No. 4 Shaft at the Lucky Friday Mine is the largest capital expenditure in the corporation’s 128-year history and is considered the deepest shaft in the United States. This paper will discuss the project’s history and lessons learned from the initial conceptual design work in 2007 through project commissioning in 2017. Change management was key for the owner, contractors, and vendors in delivering the operational and organizational success on the project. The No. 4 Shaft has extended the life of the Lucky Friday Mine by 21 years to 2039. INTRODUCTION The Lucky Friday Mine of Hecla Mining Company (Figure 1) is the oldest active (77 years) and deepest mine in the Coeur d’Alene mining district, producing approximately 725 tonnes (800 tons) per day from narrow, vertical, silver, lead, and zinc veins. Primary access into the mine is via the Silver Shaft, a 5.5-m (18-ft) diameter, concrete lined shaft sunk to an original depth of 1,890-m (6,200-ft). Current production is from the Gold Hunter vein system, approximately 1,525-m (5,000-ft) northwest of the Silver Shaft.Cut and fill stoping is currently employed at depths to 2.3 km (7,500 ft) below ground surface, making it one of the deepest mines in the western hemisphere. No. 4 Shaft is a 5.5-metre (18-foot) diameter, concrete lined circular shaft, constructed as a 1.2 km (3,860 feet) deep winze in the Lucky Friday Mine. The 2.4 m (8 ft.) diameter, double drum, double clutch, Siemag hoist and associated headworks are situated at the 4760 level, top station at 4940 and shaft stations at 5900, 6500, 6580, 7500, 7580, 8300, 8380, 8500, and 8620. Shaft stations reference depth below Silver Shaft top station. The 4 Shaft was designed, constructed and commissioned over ten years, between 2007 and 2017. Basic design work was completed by Nordmin Engineering, followed by detailed design completed by Cementation Canada. Shaft construction was awarded to Cementation USA and lateral development was initiated in early 2008. Over the course of the next nine years, the project was suspended and restarted twice, dealt with the loss of a miner, added scope including shaft depth and mine infrastructure facilities, experienced squeezing ground that required liner replacement, changed excavation section, and dealt with a final alignment that was not within design requirement for verticality. Hecla and Cementation were successful in delivering a facility that provides fully functional access from collar at 4940 level to shaft bottom at the 8620 level. Two active mining levels below the collar, 5900 and 6500 are accessed. In addition, the shaft provides access to the future mining level at 7500, skip loading facility at 7580 level, station and loading pocket cutouts at 8300 and 8380 levels, spill pocket at 8500 level, and shaft bottom pumping facility at 8620 level (Figure 2)."

Jan 1, 2019

By G. M. Card, K. D. Card, B. V. Sanford

The Canadian Shield and its extensions are traversed by an orthogonal system of north-west and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches in?uenced patterns of sedimentation and tectonism in the intervening epicratonic basins andmarginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structuresalso triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By M. J. Michaud, M. J. Lavigne

"A cornerstone of any successful mining project is an understanding of the mineral assemblage and metal distribution comprising the deposit. Knowledge of the precise mineral/ metal zoning enables an operation to utilize different mining and processing methods optimized for different parts of the deposit. The Lac des Iles mine, located in northwestern Ontario, is one operation that depends on a good understanding of these issues. Current resources for the Roby Zone total 94.1 Mt grading 1.66 g/t Pd, 0.18 g/t Pt, 0.14 g/t Au, 0.062% Cu, and 0.053% Ni.The Roby Zone occurs within the gabbroic portion of the Lac des Iles intrusive complex and consists of three compositionally and texturally different ore types with variable PGE, base and precious metal contents. PGE occur as sulphides and bismuthotellurides in net-textured sulphides, coarse sulphide blebs and as finegrained inclusions within secondary silicates.Knowledge of the precise mineral/metal zoning has directly and indirectly improved several operational aspects, including resource modelling, mining, and processing. For example, metallurgical recoveries have been increased by up to 3% to 5% and concentrate grades have increased by up to 100%. IntroductionLac des Iles Mines Ltd., a wholly owned subsidiary of North American Palladium Ltd., owns and operates a 3000 t/d open pit mine and concentrate facility, located 100 km north of Thunder Bay in northwestern Ontario. The Lac des Iles PGE-gold-copper-nickel mine has been in commercial production since 1993 and in 1997, produced 1.8 million grams of palladium, 127 000 g of platinum, 114 000 g of gold, 438 000 kg of copper and 354 000 kg of nickel (North American Palladium Ltd., 1998).Under the Industrial Research Assistance Program (IRAP), a two-year study of the mineralogy of the Roby Zone was undertaken with a goal of improving the profitability of the mine. Geological mapping, petrography and geochemistry of the Roby Zone were completed during this study. Utilization of the detailed mineral/metal zoning identified as part of this study was implemented at the mine and shown to positively impact many operational aspects including mining and processing."

Jan 1, 2003

By A. R. Miller, M. C. Bétournay, D. L. Barnes

"A number of successful proof-of-concept projects have been carried out to replace conventional power application, such as diesel and rechargeable batteries, in underground mine vehicles. This has led to the development and testing of the world’s first fuel cell production vehicle, a mine locomotive. A fuel cell loader is being built and tested.This paper provides an insight into other projects that are being carried out. Some are related to further underground applications, and some to further research, such as refueling options, power plant durability, and vehicle automation.Also outlined is an evaluation of the overall mining applications and advantages this technology can bring to underground mining, including the facilitation of automation and tele-remote operation."

Jan 1, 2003

By G. M. Card, K. D. Card, B. V. Sanford

Abstract-The Canadian Shield and its extensions are traversed by an orthogonal system of northwest and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches influenced patterns of sedimentation and tectonism in the intervening epicratonic basins and marginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structures also triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By Fred C. Delabbio

The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation. This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited, Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project.

May 1, 2003

By G. Auld

"A simple method is presented whereby the additional quantity and static pressure necessary to compensate for ventilation duct leakage may be estimated using the circular reference functions of modern spreadsheets. Favourable comparisons have been made to the National Coal Board (United Kingdom) design charts and to a case study analysis. IntroductionIn mining, most ducted systems are applied to the development of access tunnels, and most of these systems leak to some extent. When the ventilation duct fails to deliver the required quantity of air to the work place, there is a significant contribution to the development costs, either directly or indirectly.Directly — More air and more pressure are required to compensate for the leakage, more capital development (ventilation shafts, parallel drives) are required because ventilation systems cannot push the fresh air far enough, and longer re-entry times to ensure toxic blast fumes to be diluted.Indirectly — There is a reduction in productivity because of the inclement atmospheric conditions, and/or closure of development ends because of unacceptable atmospheric conditions at the working place. This has been exacerbated over the last few decades because of the increased use of diesel equipment of ever increasing power, and the more stringent Occupational Health and Safety requirements demanding more air flow per kilowatt of diesel power.The leakage from a duct must, therefore, be reliably estimated in order to assess the effectiveness and construction of the system; assess the effectiveness of the maintenance or repair of the duct; appreciate the cost of the leakage, and therefore apply effective maintenance and installation procedures; and engineer safer, healthier and more cost-effective ventilation systems."

Jan 1, 2002

By Biplop Das, E. Herrera, A. Burrows, P. J. Mackey, G. R. F. Alvear Flores

Since the first commercial plant was built at Mount Isa, another twenty ISASMELT™ furnaces have come into commercial operation, and construction of new plants continues. The primary copper ISASMELT™ top submerged lance (TSL) technology continues to attract interest from potential users who seek to smelt productively. In addition to the known benefits of productivity and flexibility, ISASMELT™ operators have also achieved improvements to energy efficiency when switching from their previous technologies. The recent production statistics for operation at Tuticorin, India show that ISASMELT™ has taken the first steps into territory beyond 400,000 t/y (copper cathode basis) and this will likely be the scale chosen by future new copper smelters operating purely on a toll smelting basis. Highly energy-efficient technologies will be expected at these smelters

Jan 1, 2015

By H. R. Banks

IF you have ever travelled in the valley lying between the Selkirks and the Rockies in the East Koorenay district, you will have noted that the former mountains are rounded and massive, while the serrated peaks of the latter, fingering into the sky, bring an entirely different. picture. These two mountain ranges, with the comparatively level valley between, serve splendidly to introduce the subject for discussion. It is rather strange that, despite the fact that wear is undoubredly the greatest force with which human ingenuity bas to contend, it has come in for very little study from the stand point of pure science. Empiricism has been the sole ally in the fight for improvement! That we may have a clear understanding as to what we mean by wear, I would include in the term the breaking dawn of ail solid matter, from the natural wearing dawn of the mountains previously mentioned, to the hale in the mill pipe-line, which forces one to shut-down-usually at some un-earthly hour-to carry out a repair. It seems a far cry from mountains to mill launders or pipe-lines, but, magnified sufficiently, most of the materials with which we have to deal would show surfaces not unlike those we see around us. The progressive steps of wear, or ?erosion&apos; as our geological friends would prefer to term it, are exemplified in the two ranges of mountains and the valley between. True, the wearing dawn by natural forces is a slow process. The aeons which have passed since first these mountains were formed seem endless. The natural forces pitted against them seem puny in the light of the interminable rime that has been needed to effect the changes. But here, as in the case of the materials with which we are dealing day by day, the combination of many forces ultimately brings about that condition which we describe as &apos;worn out&apos;. In the case of the mountains, it is when they are finally levelled into plains, and in the case of equipment which we use, it is when that equipment will no longer serve its purpose.

Jan 1, 1943

By N. C. Clarke, T. Wu, M. le Page, K. J. Henley

In 1994, Gold Mines of Australia acquired the rights to the historic Mt. Lyell copper mine, and commenced a feasibility study into expanding production. The ore was shown in laboratory tests to be amenable to single-stage, fully autogenous grinding (FAG) of underground primary crushed ore, and this route offered the maximum cost savings. Flotation performance was expected to be enhanced. However, batch flotation tests done on pilot-scale autogenously ground ore showed an unexplainable recovery loss of between 1% and 3% Cu. A second pilot plant trial was set up, with the ground product feeding banks of continuous flotation cells. Single-stage FAG, FAG/pebble and FAG/ball circuits were tested. Results confirmed a loss of about 3% recovery with single-stage FAG milling. The FAG/ball circuit eliminated the loss. Analyses showed that autogenous milling probably produced more chalcopyrite/pyrite composites and that recovery of these composites was lower than with ball milling. In size fractions below about 53 microns, where chalcopyrite is well liberated, copper recovery was less affected by milling method and flotation selectivity. It was concluded that for the Mt. Lyell situation, a FAG/ball circuit was preferable to single-stage FAG.

Jan 1, 2002