Search Documents

WINDING engines are one of the most important units in the equipment of a mine. Upon the winding machinery depends not only the output of the mine, but it supplies in most cases the only means by which workmen enter and return from the mine, and consequently the utmost care and attention is desirable in its design. The efficiency of a direct acting winding engine, as a machine is very low. In other words, the proportion between the useful work performed and the actual work the engine is capable of performing (under the most favourable conditions) is very small. The reasons for this are:-1. The intermittent nature of the work; the engine is stopped from 20 to 25 %(or even more) of the time which would constitute a useful day's work.2. The large amount of power that is absorbed applying the brakes to bring the load to rest.3. That the net useful load raised is small in comparison with dead load to be lifted, and the parts to be set in motion.4. That, owing to the frequent stops, initial condensation in the cylinders is always greater than in a continuously running engine, whilst radiation from steam pipes, valve chests, &c., goes on whether the engine is running or...

Jan 1, 1911

By Robbilliard K. R, Floyd J. M

The problems facing the metallurgical industry from the viewpoint of the range of unacceptable residues, flue dusts and slags currently produced from the electrolytic zinc process, electric arc furnace scrap treatment, and blast furnace operation in lead smelting and the Imperial Smelting Process (ISP) are addressed. The application of the Ausmelt technology is discussed and analysed for the pyrometallurgical treatment of zinc plant residues, steel plant flue dusts and lead blast furnace and ISP slags, as well as the more complex issue of smelter modernisation to avoid production of zinc plant residues in the future. Processes developed from pilot work are described and indications of the economics of treatment of electrolytic zinc plant neutral residue and jarosite are given.

Jan 1, 1993

By Moore A. J, Evans R

Blast vibration control and assessment techniques have been developed which supplement traditional charge mass scaling methods. The improved techniques, which can be used to predict air and ground vibration levels at the planning stage, and to assist in the control of blasting operations, have reduced the level of operating risk concerning blast vibration. In addition to such factors as charge mass, distance and blast vibration levels, these additional techniques take account of orientation of the blasting face, topographic shielding, wavefront reinforcement, and meteorological conditions. They have assisted in compliance with specified blast vibration levels for environmental licence and mining lease conditions, the reduction of blast vibration nuisance to residents in the area surrounding a mine, and control of building and rock structure response in adjacent areas on the mine lease area.

Jan 1, 1994

By Aziz NI, Guo H

Most of the existing models of the mechanisms of drilling and cutting processes are oversimplified in both stress state and failure criterion. On the other hand numerical modelling techniques are a more versatile method with great potential for development. In reviewing drillability and predicting performance of excavation machines the empirical tests, which simulate the physical breakage action in excavating processes are seen to be the best in terms of penetration rate predictability. Future methods of determination of drillability should concern the breakage characteristics and rock abrasivity involved in the two basic types of attack, i.e., percussive and rotary drilling.

Jan 1, 1988

Geological information plays a significant, cost effective role, in the Mt Whaleback iron ore mining operations. The geology and structure are complex. Good communication between the Mine Planning Production Scheduling and Quality Control Sections is the key to utilisation of geological information to its full potential.Drilling and pit face mapping are the two basic sources of detailed data sets which are processed to prepare up to date geological cross sections and benchwise geological plans. This information is used directly for the blast pattern design and production scheduling. Physical ore type estimation is also undertaken. Orebody models are generated from the geological information.

Jan 1, 1990

By Ofori-Ansah K

The zeta potential on the surface of activated orit carbon were estimated in lhe presence of selected cations and anions that are normally associated with gold bearing ores in Kalgoorlie area of Western Australia. Additions of such ions to solution of varying pH shifted the isoelectric point of carbon from pH 4.45 to pH 7-8.3, while the anions moved Lhc isoelectric point 10 less than pH 3.2. In the presence of gold cyanide SoluLion additions of spectator ions indicated the isoelecLric poilll to be aL pH less than 3.2; the only exception was for Fe" ion where the isoelecLric point was at pH 5.9. The decrease in zeta potential appeared to be related to the counter-ions present. The decrease may also be related to the adsorption of hydroxyl ion complexes that are likely to be formed when cations are present in the solutions.Gold adsorpLion by activated orit carbon from gold cyanide solution seem to be indicated by the magnitude of zeta potential on the carbon surface. An attempt is made to relate gold adsorption and zeta potential on carbon surface with the pH of the medium.

Jan 1, 1984

By A E. Annels, M D. Raine, I M. Platten

Lode-gold systems are often characterised by a high to extreme nugget effect (>50 per cent), and the presence of coarse gold particles (>100 ¦m in size). They rank amongst the most difficult of ore deposits types, in terms of producing an accurate and precise resource estimate. Their effective sampling is generally difficult because of the relatively low concentrations involved and erratic nature of the gold particles. Grade continuity is usually less consistent than gross geological continuity, and is typified by the localisation of grades within discrete oreshoots. In most cases drilling, particularly diamond drilling is an effective measure of global geological continuity, whereas grade can only be reliably resolved from underground development. Depending upon drill density and geology, it is unlikely that anything above an Inferred Mineral Resource can be estimated from surface drilling alone. Underground development, in-fill drilling and, potentially, bulk sampling or trial mining will be required to delineate Indicated and Measured Mineral Resources and subsequent Ore Reserves. Grade estimation will have to account for highly skewed and often multi-modal populations, extreme values, a high nugget effect and low geostatistical ranges. A clear geological model that honours both geological and grade continuity must drive the resource estimation process.

Jan 1, 2003

By Seymour K. M, Sampson D. B, Walker I. W

Ashton Mining Limited is the operator of two wholly-owned gold mine/mill complexes at Laverton and Leonora. In addition, Ashton owns 43% of the Bardoc Joint Venture mine/mill complex, which is operated by Aberfoyle Pty Limited. All three of these operations are located in the Eastern Goldfields region of Western Australia (Figure 1). At Laverton, milling capacity is in the order of 1 million tonnes per year in 3 mills (Duketon 200,000 tpa, Cork Tree Well 650,000 tpa and Craiggiemore 150,000 tpa). These mills service a distance of 80 km, from Baneygo in the north to Craiggiemore in the south. Mineral tenements cover a 150 km long stretch of a series of sub-parallel mineralised structures. At Leonora, the Harbour Lights mill is designed to treat 750,000 tpa of sulphide ore, and has treated oxide ores at an annualised rate of over 1 million tonnes/year. The mill is supported by several tenement blocks that lie within a 50 km trucking radius of the mill. The most important of these is the Mertondale tenement block, which covers approximately 25km of the Mertondale Shear Zone.

Jan 1, 1991

By Walters GW

A countercurrent method of metal refining using crystallization and reflux is discussed. 4n account is given of the development of this technique for the separation of silver and bismuth from lead using bench-scale studies to the present small pilot-plant unit (around one tonne per day) in the "Commonwealth Scientific and Industrial Research Organization (CSIRO)" Division of Chemical Engineering.

Jan 1, 1975

The basic flowsheet for the Kalgoorlie Nickel Smelter and Kwinana Nickel Refinery are discussed in relation to the mineral components of Kambalda produced nickel concentrates. Both processes handle violarite and pentlandite satisfactorily but the smelter has limitations where high copper recovery is required and in its ability to handle magnesia containing minerals. While the latter can be more economically handled at Kwinana the limitations of this tolerance are discussed together with problems arising from treating pyrrhotite, pyrite and precious metals by the Sherritt Gordon process.

Jan 1, 1973

By Clift N

Lead concentrate from the Isa and Hilton lead-zinc concentrators of Mount lsa Mines Limited is smelted at Mount Isa to produce a lead-silver bullion. This bullion is cast into four tonne blocks and shipped to Britannia Refined Metals Co Ltd, NorthDeet, England and to plants in Asia for refining and marketing. The traditional treatment stages at Mount lsa are sintering, smelting, and drossing and casting, with some of the sinter plant feed being pre-treated through an Isasmelt plant.A commercial scale lsasmelt based lead smelter was commissioned in early 1991.

Jan 1, 1993

It has been clearly demonstrated in both the first, as well as in the last world conflict, that a nation's ability to wage as well as win a war is primarily a function of its industrial, and particularly its steel making capacity, provided both are directed to munition production.The Axis gambled on their pre-war policy of bullets before butter giving them sufficient initial advantage to decide the issue before the Allies had time to gear their industries to war production.Fortunately for us, Hitler and his advisers apparently underestimated Russia's war potential, although they must have known that Russia was, in 1939, the third largest steel making country in the world, as shown by the following figures:

Jan 1, 1947

This paper deals briefly with productivity-enhancing advances in shaft sinking technology in South Africa post-World War II in general and the developments and application of long rounds since the 1980s in particular and is amply illustrated.It touches on the conversion to circular section, concrete lined shafts, the introduction of tungsten carbide drill bit inserts and grab lashing; expounds the rationale driving the development of longer rounds; and then describes the evolution of long rounds using hand-held and mechanically mounted rockdrills in South Africa and Canada by both local and foreign contractors. The recent experience gained on the sinking of the South Deep Main Shaft follows. Results obtained from this experiment are tabulated and commented upon. The paper concludes with the postulation of æwhat nextÆ and æwhere toÆ scenarios. Addenda include a list of shaft rounds in excess of three metres in length blasted in the Main Shaft at South Deep and their results, typical round design, manufacturerÆs specifications for the 6 m shaft jumbo and rock drills.

Jan 1, 2002

By Cutmore NG

The moisture content of iron ore is important in handling, stockpiling, transport and further processing operations. Typically these ores contain both `free' and `bound' moisture, the latter being moisture that is not removed in a conventional laboratory determination of moisture by air drying at 105¦C, and it is the free moisture that is important in dust control and ore handling. The CSIRO Division of Mineral and Process Engineering has previously developed and commercialised gauges, based on capacitance and microwave techniques, for the on-belt determination of moisture in coal and minerals. However, these gauges determine total moisture, and have a different sensitivity to free and bound moisture in the material analysed. Consequently, the accuracy of determining total or free moisture alone may be significantly affected by variations in the bound moisture content. An investigation has been carried out on the simultaneous determination of free and bound moisture in iron ore fines (

Jan 1, 1993

By P B. Hills, R J. Walton

Narrow vein tabular orebodies are prone to mining induced seismicity. The Tasmania Mine is a complex example of a seismically active tabular orebody, where the contrasting material properties of the host strata and of the orebody itself, serve to exacerbate the seismic response. Analysis of a continuous record of seismicity over a period of seven years has provided significant insight into the fundamental mechanics of the rock mass. Understanding seismicity to permit safe extraction of the orebody has been enhanced by instrumentation of rock mass behaviour in response to mining and mining induced seismicity. It is the purpose of this paper to explore that understanding in respect to the adoption of an alternative down-hole Avoca stoping method for use in particular circumstances.Intensive instrumentation of the Tasmania Mine over a period of four years has provided insight into the behaviour of the rock mass in response to extraction of the narrow vein orebody it encompasses. A range of instruments have been installed in clusters or single installations in order to measure changing stress conditions and the impact of those changes on the rock mass and the reinforcement system.Instruments are often installed in very close proximity to active production stoping. While it has been possible to observe the impact of the mining and mining induced seismicity at very close quarters, instruments installed in these locations are vulnerable to damage and consequently, the level of instrumentation is high. Instruments are continuously logged, typically on a six hourly basis coinciding with the end of regular blasting times. The response of the instrumentation to changed rock mass conditions is considered against the background of development and production blasting and against the seismic record to assess the viability of downhole Avoca stoping.CITATION:Hills, P B and Walton, R J, 2012. Continued observations of rock mass behaviour in response to stoping at the Tasmania mine, Beaconsfield, Tasmania, in Proceedings Narrow Vein Mining 2012 , pp 169-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By F Schoenbrunn, T Laros

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to be successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings impoundment design, underflow pumping, and control system.

Jan 1, 1998

By Duncan GR

Having passed through a number of previous phases the best longwall results in Australia have shown a significant increase in the last two years. The results expected from a longwall face can be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the utilisation, and the available operating hours. Back analysis of the results achieved suggests that, on average, recent improvements arise from the higher capacity equipment recently installed; the utilisation has in fact reduced slightly. Review of the constraints which limit the longwall results, i.e. shearer speed, AFC capacity, support, advance rate, and man travel speed, shows that little improvement can be expected in the ideal production rate in thinner seams. In thicker seams the AFC often proves the overriding constraint and further increase in equipment size could lead to increased future ideal production rates and is expected. In all cases a concerted effort to increase the utilisation achieved is likely. For deep mines with thin to medium seams this offers the most viable path to improvement; by contrast thick seams with highwall/shallow access may benefit from further increase in equipment size.

Jan 1, 1988

During late 1953 and early 1954, tests were carried out in Sydney metropolitan brickpits in order to determine if some improvement might not be effected in the personal shock, fly rock and possible ground displacement accompanying daily blasting occurrences in the numerous quarrying activities of the metropolitan area. As a result of this preliminary work (Reid, 1954), the Department of Mines decided to further investigate the problem with a view to placing this type of blasting on a sound economical and safe basis for both operator and nearby residents alike. To assist in the work, a Cambridge Universal vibrograph was acquired.Human safety was the first consideration followed by property damage to homes and factories in the extractive areas. Although most of the actual field work has been confined to the Sydney metropolitan area and in particular to the large clay-shale quarries, many cities and country towns have blasting problems associated with the extractive industries, engineering projects both above and below ground level, and in building excavations to which the results may apply.The following figures illustrate how much activity of this type is located around cities and towns:Sydney Metropolitan Area:

Jan 1, 1958

By Menne D. M, Ladyman R

Camel Creek Mine operated by Lynch Mining Pty Ltd is located 65 km west of inghain and 160 kin north west of Townsville in North Queensland. (Figure 1). The Camel Creek gold mineralisation was discovered in mid-1987 in an area previously known for its tin workings. Mining commenced in January 1989 after an oxide reserve of 1.2 million tonnes @ 2.1 g/t gold had been delineated. The first gold pour was in May 1989. The mine developed into a medium sized open cut operation, with full site facilities. The initial mining rate was 500 000 tpa utilising run-of-mine (ROM) heap leaching to recover the gold. By the end of 1990 the wider orehodies were mined and efforts were focused on the narrow orebodies, of width typically less than three metres. Smaller earth moving equipment was employed to selectively mine the narrow orehodies leading to a decrease in the mining rate to 200 000 tpa. The Red Gold deposit (80 000 tonnes « 3.0 g/t to 18 in vertical) was mined in mid-1990 and ore was hauled approximately 8 kin to the Camel Creek heap leach operation. The ore was hauled in a dedicated campaign after being stockpiled. The cost of dedicated ore haulage ensured that only the more exceptional of the remote orebodies could be mined in this manner. The Golden Cup orebody, some 20 km from Camel Creek, was too distant to permit ore haulage. However, this prospect contained sufficient gold (initially 90 000 tonnes @ 3.0 g/t) to warrant the installation of a small mobile adsorption facility. Construction of the second heap leach operation commenced in late-1990. Gold production commenced in early April 1991. Mining of several smaller orebodies remote to the second heap leach facility has been undertaken and further mining is planned. This paper outlines heap leaching practice at Camel Creek Mine and summarises the success of the Golden Cup heap leach.

Jan 1, 1994

Drag pick roadheaders and continuous miners have been applied in the coal mining industry for several decades, having replaced drill-blast methods as the primary means of excavating coal and coal-measures strata. The generally harder rock types associated with metalliferous mining have precluded the use of such machines in the past, however, developments in machine technology and increasing labour costs and environmental constraints suggest that there are now likely to be applications suited to the method. Metalliferous mining engineers are generally unfamiliar with the machines themselves and with the fundamental criteria controlling rock cuttability. This paper gives an introduction to the machines and the controlling factors.

Jan 1, 1987