Search Documents

By Grossi M, Baiden G

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and on- site applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no de- watering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

In order to satisfy environmental and mine operational requirements it is becoming increasingly important to minimise ground blast vibrations at certain locations. These locations are often in soil or on large resonant structures such as grain silos, highway bridges or even the walls of an open pit. A soil monitoring exercise was carried out to evaluate the common practice of coupling vibration detectors to the ground using spikes. At a series of locations in an operating quarry the spiked array response to single blastholes was compared with that of an accelerometer array attached to a calibrated embedded mount. The results clearly showed that the spiked arrays over-estimated the true ground vibration by 46.5 per cent on average, with a maximum observed error of 99.2 per cent. These errors are considered too large for compliance monitoring where accurate vibration levels are required for comparison with prescribed limits. Although spike coupling is convenient, its use for compliance monitoring should be viewed with caution. Unfortunately, however, many manufacturers supply their detectors as spiked arrays. A structural monitoring exercise was also carried out to evaluate the vibration response of a grain silo, highway bridge and a pit wall to the initiation of single blastholes. In this case accelerometers and standard geophones were firmly attached to the bridge which resonated at low frequencies. The results clearly show that, due to their limited low-frequency response, the geophones typically measured only half the true vibration level as measured by the accelerometers.

Jan 1, 1995

Woodlawn Mines began underground operations in 1986. At the time of going underground it was envisaged that there would be no 'contract' payment to the underground employees. This was a relatively unique step to make, especially as most major underground mines in Australia relied heavily on the contract system to motivate their workforce. (Obviously with varying degrees of success.) Woodlawn faced the task of motivating their employees through a multi-skilled system with a great emphasis on leadership and a genuine care for their employees. The 'proof of the pudding' is that Woodlawn has not lost any time over industrial issues since beginning underground operations in 1986. To achieve success in any operation the organisation must not only be advanced in its management principles but also be prepared to be innovative in the way it deals with physical problems, ie ground control, equipment selection and maintenance. Difficult ground conditions at Woodlawn have necessitated the deployment of two Cabolt Jumbos and the construction of cost-effective shotcrete systems. The shotcrete system now being built has been tested in a prototype form and is proving to be a safe and simple way to manage weak, low stress friable ground. Although the ground at Woodlawn has low stress component by virtue of the fact the ore can have a density of 4.5dm3, cable dowelling has become a necessity. The two cable dowel jumbos install high quality reinforced cables. The pressure of 'production' means that these machines must be consistently available for use and the training of maintenance personnel and operators ensures that a maximum of cable dowels can be installed over any given time span. In any modem mine ventilation is a primary concern and the major area of concern comes from the vehicles themselves. In our recent replacement for the standard 'Toro' loader, three engine options were considered. A relative newcomer to underground mining was accepted. The Detroit 60 series (DDEC) engine came with a great reputation and has lived up to this. The engine has an electronic management system that reduces particulates to a hardly visible minimum, provides great amounts of engine power and reduces fuel consumption by approximately 45 per cent. The operational benefits of such an engine are worth sharing through this conference.

Jan 1, 1995

The objective in design of an excavation in a jointed rock mass is to achieve a prescribed degree of control of rock mass displacement around the excavation. Any excavation in jointed rock usually involves slip and separation along discontinuities as well as translation and ro- tation of constituent rock blocks. Thus, any acceptable model of behavior around an excava- tion must be capable of simulating the force displacement paths followed by the constituent elements, including rigid body translation and rotation. The distinct element method models such behavior by simulating the rock mass as an assemblage of rock blocks which interact through corner and edge contacts. Discontinuities are regarded as boundary interactions between blocks with joint behavior prescribed for these inter- actions. Introduction of structural element logic allows a variety of installed support sys- tems to be modeled. The response of the support to axial, transverse, and flexural loads is based on explicit algorithms similar to those used in the distinct element formulation. This allows large displacements and rotations and general non-linear constitutive behavior for both the support elements and the interface with the rock. This paper describes both the distinct element and structural element formulations and demonstrates several applications involving sup- port interaction with jointed rock.

Jan 1, 1987

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

By Corrans I. J

A wide variety of copper-bearing gold ores exist throughout the world which have yet to be processed economically for gold recovery. The copper minerals present in these ores can be many and varied and usually result in high cyanide consumptions and problematical levels of copper in leach solutions. The copper content is often assessed as being of nuisance value as the ores are generally of the grade or type which can support neither a copper project nor a straight gold project, due to the interference of copper. Many of these problematical gold-copper ores could possibly be processed economically for gold recovery using a novel ammoniacal cyanide leaching system which utilises a copper-ammonia-cyanide complex as an effective lixiviant for gold, yet limits copper dissolution and conserves cyanide. Results from recent testing have promoted a re-evaluation of the economics of treating some gold-copper ores. This paper describes the novel leaching process and discusses the conditions employed to treat a variety of gold-copper ores.

Jan 1, 1992

By Heidecks C

Sub-level stoping with consolidated rockfill is the main method for mining steep dipping baryte and fluorite veins in Germany. Drifting is fully mechanised using drill jumbos, LHD units and shotcrete support. Stopes have heights up to 50 m with sub-level distances up to 15 m. Winning of the pillars between sub-levels is done by longhole blasting in slices of 3-5 m length on strike. Mucking is done on the lowermost level by LHD units. After each blast rockfill with binder (cement and/or fly ash) is dumped into the scope from the uppermost level. Economic success depends on both geological and technical parameters and factors, eg vein thickness and dip, ore grade, size and distance of sub-level drifts. Of particular influence are ore loss in pillar winning and dilution both in drifting on vein and in pillar mining. A comprehensive computer program has been developed for calculating the total cost per tonne run-of-mine ore respectively per tonne of concentrate for a single stope. The cost model includes development, longhole blasting, mucking and haulage to the mill, milling and ventilation. All costs (labour, energy, supplies, maintenance, depreciation and capital cost) are taken into account. Dilution and recovery are both considered. The program can be used to estimate the cost of mining a particular stope. It can also be used to investigate the influence of relevant parameters and factors on the economic result. By this way it should be possible to optimise the technical design of a stope.

Jan 1, 1995

By Singh RN

Monolithic packing systems have gained in popularity as a gate side packing method. However, there has been no detailed investigation to assess their underground strength behaviour. This work includes the laboratory and in situ investigation for strength behaviour determined on various monolithic packing materials namely Tekpak-XX, Hydropak-20, Hydropak-30, Astrapak-3R, Flashpak, Thyssen pack and Aquablends. A simple technique for assessing the pack strength was developed at the laboratory by using a penetrometer, of which penetration resistance can be directly correlated with the uniaxial strength of the pack. The in situ strength investigations were made on core samples obtained from three pipes inserted inside the pack, while the penetration test were made on the pack surface. The in situ results indicated that the packing material develops an inconsistent strength on various part of the pack which was mainly related to an inadequate mixing of grouts inside the pack.

Jan 1, 1992

A simulation of the fluid flow, minera- logical and chemical aspects of in situ leaching is being developed for application to the recovery of metals from unbroken, naturally jointed rock. The fluid flow aspect has been developed. The rock is assumed to have a double-fracture property. A major joint set is responsible for bulk flow of solution, while a minor joint set, intersecting with the major set, allows the solution to contact the reactive minerals. The two-dimensional fluid flow through the major joint set is analysed by a streamline model for a particular well pattern. The other important components of the model are described briefly.

Jan 1, 1984

Total extraction is a misnomer and invariably some coal losses occur in the mining of pillars. "Fulls" pillar extraction is by the pocket and fender method, the splitting method or the open end method, with extraction in the pillar, and in rows of pillars in planned sequence, using combinations of coal and timber and roof-bolts for support. Where circumstances dictate, partial extraction is used, leaving behind portions of pillars in large blocks for support. The use of such extraction plans and supports as minimum guidelines has contributed greatly to safety in United States Coal Mines.

Jan 1, 1974

Gold mineralization like other low concentration high value commodities has gained the notoriety of being difficult to sample. This adversely affects the confidence that can be placed in resource estimates and ore reserves. As an example, it is not uncommon to find differences of the order of 30% between duplicates of a single sample sent to two different commercial laborartories. Two halves of drill core generally show marked differences in grade. Again differences of 50% are not uncommon in halved core. In the context of this type of "error" within the base data used for the resource estimate, many of the subtleties of computation methods and expert judgement of resource categories, are almost a case of shutting the gate after the horse has bolted. Managers, financiers and consultants must question the quality of the base data upon which resource estimates are made. They must insist that standard and duplicate samples are used to measure the accuracy and precision of commercial analytical laboratories, that sampling practices have been checked for possible bias and give tolerable repeatability. Further they must ensure there can be a realistic confidence in the estimates by correctly using these measures of data quality to quantify risk.

Jan 1, 1990

A system for rapid on-line determination of weight percentage coal in slurry and weight percentage ash in coal has been developed at the Julius Kruttschnitt Mineral Research Centre, University of Queensland. The gauging system is suitable for use with coal flotation slurries or slurries having a maximum particle size of about 1 millimeter. The system is based upon measurement of gamma ray transmission; radioisotope sources emitting photons of two widely different energies are employed. The inaccuracies of measurement that would normally result from variable amounts of air entrained in the slurry are substantially reduced by pressurising the slurry to approximately 2MPa (300 psi) using a Mono pump. The equipment can be used to make measurements on more than one slurry stream by pumping streams sequent- ially. The system is being tested at the Peak Downs Mine of the Utah Development Company in Central Queensland. This paper describes the theoretical principles of the gauge design, the experience gained to date in the commissioning of the equipment, including the installation of a PDP 11/03 computer, and the progress made in developing satisfactory interpretations of the gauge count-rate output.

Jan 1, 1978

Comminution Kinetics equations are developed to take into account difference of grindability of mineral components. The equations describing both batch and closed circuit grinding or crushing processes are given. These equations are applied to industrial data to derive comminution kinetic and classification characteristics of the component minerals in a multi-mineral ore. Control strategy based on these concepts is presented.

Jan 1, 1985

By Wood CJ, Davis JJ, Askew H

A dynamic model of a dense medium circuit has been developed and tested against plant data. The model shows the response of the circuit to both controlled (changes in specific gravity set point or changes in circuit coal feed rate) and uncontrolled changes (changes in raw coal moisture, loss of raw coal feed) in operating conditions. The model is built up from dynamic models of the individual sumps, pumps, pipes, splitters, magnetic separators and automatic controllers in the circuit. The model can be used for design of automatic control loops and for investigation of possible process modifications such as changes in water addition points. This paper describes the model construction, the testing of the model against actual plant data and gives some examples of its use in investigating plant response to changes in operating conditions.

Jan 1, 1978

In the stability assessment of open pit walls, geotechnical engineers have to deal with uncertainty related to structural geology, rock mechanical parameters, groundwater and so on. This uncertainty will immediately and significantly impact on wall stability assessment and therefore. influence mineral recovery and ultimately the financial return of open pit mining. However, the conventional factor of safety applied to measure the stability of slopes and the relevant analytical computer packages cannot quantitatively consider the variability or uncertainty of the input data. As a supplement, therefore, geotechnical engineers have begun to apply probability to the stability assessment of open pit walls over the last two decades. To-date unfortunately, no powerful computer package is available to geotechnical engineers to conduct the probability analysis of slope stability. This paper presents a computer package of probability analysis for rock and soil slope stability. In this computer package, the strength parameters of rock and/or soil material such as cohesion, friction angle and unit weight of the different rock and/or soil type domain in a complex structural geology environment can be considered as the basic input random variables. Groundwater level can also be taken into account as a random variable in this package. Two `rigorous' limit equilibrium solutions, the Morgenstern/Price method and the Sarma method, can be used to calculate the factor of safety during Monte Carlo Simulation applied in this program. Five types of probability distribution are included in this package for the user to simulate basic input random variables. Two realistic cases from BHP Iron Ore are used to illustrate this package.

Jan 1, 1997

The standard charge weight scaling laws imply that only one particular delay (that possessing the maximum instantaneous charge) contributes to the ppv. However, the present analysis clearly demonstrates that a varying number of blastholes contributes to the ppv. This number also increases with distance, x, between the blast source and the detector, and is caused by waveform broadening due to attenuation. Thus the operative charge weight, itself, is also a function of the distance, and so makes the standard charge weight laws difficult to implement. If the delay time scatter is neglected, then, under certain conditions, relatively simple expressions can be derived for the ppv magnification, FN, as a function of the number, N, of blastholes. When the influence of delay scatter and random fluctuations in each blasthole vibration is included using Monte Carlo simulations, then, to a first approximation, the condition FN=KNx applies, where KN is a constant dependent upon N. Unfortunately, however, for any particular blast this condition cannot be distinguished from the standard charge weight scaling law. The dependence of ppv on N would only be apparent if blasts of differing N were to be compared in an otherwise identical environment. Since this situation is very difficult (if not impossible) to realise, then the influence due to N, although significant, goes largely undetected. Another problem associated with standard charge weight scaling laws is the difficulty of accurately assessing the appropriate charge weight, even if attenuation broadening is neglected. For example, if a number of blastholes are very close, then they experience a vibration interaction which is non-linear. However, if the same blastholes were to be widely spaced, then the separate vibration signatures add linearly. The standard charge weight scaling law fails to distinguish between such linear and non-linear regimes. Unfortunately, in many production blasts, both regimes exist throughout various portions of the blast spatial pattern and so makes it difficult to determine the operative charge weight. The solution to the combined influence of waveform broadening and linear/non-linear interactions will obviously require substantial future research. A possible solution may be found in the use of numerical dynamic codes.

Jan 1, 1990

By Culshaw MG, Deaves AP, Bell FG

The accurate prediction both of the water ingress into sub-surface excavations and the nearby groundwater pressures is of fundamental importance to the control of the stability and flooding of tunnels or mines constructed below the water table. Predic- tions are usually based on laboratory and in situ permeability determinations together with observations of groundwater conditions in boreholes. Although established theoretical methods provide a basis for prediction, the actual ingress depends on many factors. The objective of this paper is to explore the geological controls on groundwater conditions, and the available methods of prediction of both groundwater flow and pressure are outlined. Salient points are emphasised by reference to a case history involving the construc- tion of a tunnel in a faulted and mixed sequence of sandstones, siltstones, shales and coals. Water ingress quantities have been monitored for a variety geological and geotechnical conditions including heavily faulted and mine disturbed ground. The overall results are discussed with reference to the relevant hydrological and geologi- cal conditions in terms of the geological structure, lithology and rockmass condition as well as the construction methods.

Jan 1, 1988

When lying over 200-250m depth, many seams and surrounding strata are gassy enough to create mining difficulties , particularly in highly productive longwalls as well as in their development headings. In addition to the gassiness of seams or stra- ta in the outgassing volume around working, the shape expansion and limits of this one influences much the intensity of gas emission. These charac- teristics of outgassing volume differ very much ac- cording to the permeabilities of the seams and strata encountered by their fracturation due to mi- ning. Moreover, the shape of the outgassing volume is very much modified by the rate of advance of the face. In nearly impermeable deposits, gas flows from a limited outgassing volume. When the rates of advance of a face are medium or low, the shape and dimensions of this volume do not change very much and outgassing volume is translated progressi- vely with the face advance. This explains why, in the past, it was observed that there was for each seam an average steady specific emission of gas, round which the volume of gas evolved per mined ton or per mined unit area, calculated over a cer- tain time, was oscillating. Combined with a statisti- cal irregularity coefficient, this allowed prediction gas of emission and thus to take decisions for air ventilation, drainage, and eventually production.

Jan 1, 1988

By Crosby N. R

The design of mine openings and the assessment of their reserve are processes ihicl, require the routine manipulation of considerable amounts of data. A number of computer programs have been assembled to operate in a mini computer in order to provide some mechanical assistance for these processes. The system responds to plain language commands. which allows mining engineers to compute the reserves for a number of possible mining outlines, on an interactive basis. Methods of numerical analysis were used in preference to statistical or qeostatistical techniques.

Jan 1, 1977

By La Brooy S R, Fenton K

A low grade copper flotation tailing from Telfer containing 1.2% Cu as chalcocite and cuprite and 5 gt-t Au was leached with ammonia, cyanide and ammonia-cyanide mixtures to extract copper and/or gold. Direct cyanidation extracted both copper and gold but consumed about 30 kgt 1 NaCN. Pre-leaching the tailing with an aerated ammonia solution containing 28 kgt 1NH3 and 17 kgtl(NHa)2S0a at pH 10 readily extracted up to 95% Cu in about 6 hours under optimum conditions. However pH and total ammonia concentration were critical factors. Subsequent cyanidation ex- tracted 80% Au using 6 kgt NNaCN. Ammonia-cyanide mixtures werefound to selectively leach gold over copper depending on the concentration and relative proportion of NH3 and CN. The best composition for leaching up to 80% Au from Teller tailing was 1.6 kgt t NaCN and 1.1 kgf 1 NH3 in the presence of 0.3 kgt t Cue+. Such a mixture left only 50 mgL-1Cu in the final solution after precipitation of some of the initially dissolved copper.

Jan 1, 1991