Search Documents

By M W. A Asad, E Topal, D S. S Sandanayake

Underground mine planning requires an optimal stope layout as a prerequisite for the definition of an optimal production schedule. The procedure to generate an optimal stope layout considers an orebody model and economic parameters as inputs. It evaluates all possible combinations of mining blocks and creates a set of stopes by satisfying the physical mining and geotechnical constraints. Thus, the procedure is computationally complex, and generating a solution to the problem is a challenge. This paper presents an implementation of a new heuristic algorithm that solves the stope layout problem. In two case studies, the algorithm achieves 11.2 per cent and 22.5 per cent superior solutions to the industrially available maximum value neighbourhood approach.CITATION:Sandanayake, D S S, Topal, E and Asad, M W A, 2014. Implementing a new heuristic approach to the underground mine stope layout problem, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 243–248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Wang SS, Frattaroll DR

In the development of novel sulfide collectors, especially for the low-lime and acid circuits, flotation of chalcopyrite, chalcocite, covellite and pyrite was studied with both new and commercially available S- containing collectors. The natural float- ability of sulfides, water quality, and redox potentials - all of which were considered im- portant in assessing collector strength and selectivity - were also investigated. Chalcopyrite exhibited the highest natural floatability. The response to most collectors, however, was chalcocite > covellite > chalcopyrite > pyrite. Water quality had a very significant effect on both natural and collector-aided floatability. De- ionized water and tap water had a flotation suppression effect compared with doubly- distilled water. Flotation results with single minerals are correlated with those for copper and pyrite from natural ores. Several novel collectors have now been developed for sulfide flotation in acid, neutral or mildly alkaline circuits. The results for four of these collectors, which have shown promise in commercial applications, are discussed in this paper.

Jan 1, 1986

By M R. Asef

Although generation of environmentally harmful hydrogen sulfide is considered to be related to sour gas fields, sweet gas reservoirs and waste fluids, travertine springs and geothermal fields may also produce acid gas (H2S and CO2) under certain conditions. The potential parameters influencing such a possibility need to be fully investigated to evaluate the extent of the consequences and predict hydrogen sulfide generation accordingly. Reports on hydrogen sulfide production at different regions and fields were gathered worldwide for the cases when some of them did not have such a problem previously. In order to inspect different aspects of these case studies, some other regions with no hydrogen sulfide content were selected as control. In all cases water samples were taken carefully for chemical analysis in the laboratory. Besides, mineral compositions were characterised in some cases for better evaluation. In order to give a thorough prospect of hydrogen sulfide production, a geochemical model was prepared. In situ engineering geological conditions, especially pressure and temperature, were assigned in the model to investigate the possibility of H2S generation using PHREEQC software. The results of modelling revealed that although many similarities existed between mineral compositions of the cases, certain formations were particularly prone to hydrogen sulfide generation. For better evaluation, important exchangeable cation ratios such as potassium/sodium, calcium/magnesium and ion proportions like sulfate and chloride were calculated as trends of the formations. As expected, the model could successfully monitor a higher ratio of SO42- and Cl- in potential H2S generator formations. Wide variation in percentage of HCO3- was considered as a secondary observatory parameter for better estimation. In addition, it was noticed that higher anion content created an environment ready to absorb any cations and this makes H2S generation easier. Finally, using correlations between predictors and estimators for low depth and deep samples defined the degree of effectiveness for every sample.

Sep 26, 2011

Following the Moura No 2 Wardens Court of Inquiry and subsequent changes to the Queensland Mining Legislation there is a requirement in Queensland coal mines for: a person with the recognised competencies to be appointed at each underground coal mine to the position Ventilation Officer; and the person is directly responsible for the implementation of the mine ventilation system and for the establishment of effective standards of ventilation for the mine. The Regulations require that an underground mine must have principal hazard management plans that provide for at the least the following: emergency response, gas management, methane drainage, mine ventilation, spontaneous combustion, and strata control. Other than strata control all the plans require the ventilation officer to have roles and responsibilities to develop, control, monitor and undertake actions in relation to these plans.There are also another 34 Regulations that either directly or indirectly requires the Ventilation Officer to take actions.The purpose of this paper is to outline the information that the regulators look for in sealing plans and the actions the regulators will take if the sealing does not go to plan (TARPs being exceeded).

Jan 1, 2005

By Kay JR

In 1984 a new Regional Geological Mapping Program (RGMP) was commenced by the Geological Survey of Queensland (GSQ); the new program was in response to the withdrawal of the Bureau of Mineral Resources from regional mapping. Areas for mapping were selected in northern and south-eastern Queensland on the basis of potential for mineral discoveries, level of company interest, inaccuracies in the first edition mapping and interests of other organisations (government and universities) in joint projects.Geological provinces of particular interest in northern Queensland are the Hodgkinson Basin, parts of the Georgetown Inlier not covered by earlier BMR-GSQ mapping, Broken River Embayment, Burdekin Basin, Lolworth-Ravenswood Block, Campwyn Block and Anakie Inlier. The 1:250,000 sheets covering these areas of interest are shown in Figure 1 including those already completed, those in progress and those planned for future investigation.A flow chart showing the various phases for RGMP projects is shown in Figure 2. Data collection has two facets: (i) field recording and (ii) office work including air photo interpretation, study of company reports, literature research, petrography and various laboratory studies. Two main strands of information collected are represented by a data base and compilation sheets. Compilation sheets are generally at 1:25,000 scale and are available for purchase. The current data base is very fragmentary and can be accessed only by direct contact with the relevant geologist or via written reports. A more accessible field data base is in the process of being introduced this year; this field data base (REGMAP) is based on standardised data recording and computer storage.

Jan 1, 1986

By H Law, M Muller

Mount Isa Mines (MIM) Copper Concentrator currently utilises Agitair 120 banks for its roughing flotation circuit. Apart from a rotor change, the only other significant work completed to the Agitair banks since their installation and commissioning over 40 years ago has been a like for like refurbishment in 2016. The Agitair banks at the MIM Copper Concentrator currently utilise the Pipsa rotor design which progressively replaced the original Chile X rotor design in the 1980’s and 90’s in the copper concentrator. Since the development of the Pipsa rotors, modern rotors such as the Dorr-Oliver (DO) high shear rotors have been released to the market with proven recovery and concentrate grade improvements over previous rotor designs. This paper aims to detail the installation, testing and comparison of Pipsa versus Dorr-Oliver rotors in two different flotation sections of the MIM Copper Concentrator.CITATION:Muller, M and Law, H, 2018. High shear rotor trials in the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 393–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Borshoff J, Coles R

The Rum Jungle Uranium Province is lo cated on the western margin of the Pine Creek Geosyncline approximately 60km south of Darwin. Uranium was discovered in the Embayment area (Whites Deposit) in 1949, spurring active ex- ploration and leading to the discovery of the Rum Jungle Creek South Deposit in 1959. With the discovery of the Alligator Rivers Uranium Field, new criteria in the understanding of the controls for mineralization sparked a re- surgence of exploration activities in the Rum Jungle area. Uranerz Australia Pty. Ltd. (UAL) commenced exploration in the area in the late 1970's in joint venture and in its own right. Two domal Archaean granitic complexes, the Rum Jungle and Waterhouse Complexes, domi- nate the area. They are unconformably mantled by Lower Proterozoic sediments metamorphosed to middle to upper greenschist grade. The Lower Proterozoic sediments are unconformably over- lain by remnant blocks of Carpentarian sand- stone, generally preserved in downfaulted blocks. Over a six year period extensive geolo- gical, geochemical and geophysical programs were conducted to reinvestigate previous target areas and locate new prospective zones. Exten- sive shallow bedrock drilling showed that lo- cally the stratigraphic succession is quite variable and cannot always be divided into an ordered succession for correlation with groups and formations established by the Bureau of Mineral Resources (BMR). Deformational events resulting in intraformational recumbent folding and overthrusting also account for repetition of certain lithotypes.

Jan 1, 1984

By I Sherrell, R Jain

Worldwide iron ore feed grades are trending downwards and will continue to do so with the increasing difficulties of upgrading ores. This has led to operations looking for ways to capture current tailings that still contain valuable material. In the past, these were acceptable to dispose of, but this practice is no longer economically feasible. With the increasing trend of re-mining previous tailings deposits that could be decades old, new equipment designs have been introduced to upgrade current or historic beneficiation plants. These designs can effectively upgrade these tailings to saleable products.Outotec conducted test programs for upgrading iron ore tailings from flotation rejects, thickener underflow or tailings dumps on samples provided by customers around the globe. The studies utilised Outotec’s SLon vertically pulsating high-gradient magnetic separator in combination with preprocessing equipment such as low-intensity magnetic separation, screen or scrubber and flotation for downstream processing of the magnetic concentrate. A review of the equipment required to economically process these tailings is provided, along with testing data and industrial implementation examples. The effect of different operational and design parameters on Fe grade and recovery from processing each tailings sample has been highlighted.CITATION:Jain, R and Sherrell, I, 2015. Iron ore tailings reprocessing to maximise ore production, in Proceedings Iron Ore 2015, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M Suzuki

Although several models for the surface tension of molten oxide slag have been proposed, suitably accurate predictions of this property are not yet possible. The surface tension, or surface excess free energy, of molten oxides is largely determined by the ionic coordination induced by surface relaxation. However, the associated mechanism of surface structural relaxation for molten oxide mixtures such as slag is complex and not yet fully understood. To allow a better evaluation of surface relaxation characteristics, the present work analysed the ionic coordination associated with the surface-relaxed states of several oxide mixtures. This work especially focused on calcium aluminate slags because these materials exhibit complex relationships between composition and surface tension. The effects of incorporating low concentrations of SiO2 as a surface active component on the surface ionic coordination were also examined. X-ray absorption techniques were used to assess oxygen and cationic elements in glassy samples after surface relaxation treatments, and molecular dynamics simulations based on a polarisable ion model of molten slag with vacuum/melt interfaces were also performed. The X-ray absorption techniques provided data related to electron yields (which are primarily associated with surface features) and fluorescence yields (which evaluate the bulk material). Thus, the ionic coordination characteristics of both regions were investigated. The results of molecular dynamics calculations allowed statistical analysis of the distributions of Al- or Sicentred polymorphs as well as the bond angles between cations and oxygen anions in the vacuumexposed and bulk regions in the equilibrated melt. The results indicated that bridging oxygen ions were preferentially distributed in the relaxed surface region rather than non-bridging oxygens. These bridging oxygen ions represented vertex connections between AlO4 or SiO4 tetrahedra. In the case of the calcium aluminate slags, the addition of one Ca2+ ion as charge compensation for two Al3+ ions was found to be necessary to form two AlO4 tetrahedra. This specific feature of surface ionic coordination could be responsible for the complex trends observed in surface tension data. The incorporation of low concentrations of SiO2 reduced the proportion of tetrahedrally-coordinated Al ions such that higher coordination states become dominant in the bulk of the material, whereas AlO4 tetrahedra were preferentially distributed in the surface region. SiO4 tetrahedra were the preferred Si-centred polymorph and were likely connected to one another to form bridging oxygen ions at the surface. On the basis of these results, a model to predict slag surface tension was proposed, and the energy of the formation of the ionic clusters resulting from surface relaxation was taken into account.

Aug 21, 2024

In 1556, Agricola noted that "a prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him"(1). In today's world, the owner rarely has the opportunity to visit the mine and, instead of reading about the `nature of the vein' in annual reports, prospectuses, government publications, et cetera he sees the words `reserves' and `resources'. Unfortunately, the subject of reserves and resources has become increasingly complex and Canadians, along with their counterparts in Australia and elsewhere, are still struggling with definitions which will attempt to cover all conceivable circumstances from national or regional resource endowment to the material to be extracted next week from a given stope or open pit bench. The providers and recipients of reserve and resource data are: - Government agencies who are concerned with questions of national endowment, strategic use of raw materials and other questions of public policy. - Stockholders who have a vested interest in the basic assets of their companies. - Financiers who are concerned about the security of their loans. - Regulatory bodies whose function is to protect a frequently naive investor from unscrupulous practices. - Management, at head office and on-site, who need basic information for decision-making, whether it be to open up a new mine, expand or close an existing operation, acquire or merge with other entities, or, more mundanely, for routine mine planning. To satisfy their demands with unanimously accepted definitions is a formidable task but, it is my impression that, little by little, a concensus appears to be growing within the industry.

Jan 1, 1987

By D Reid

Characterisation of non-plastic segregating tailings presents a number of challenges: the material cannot typically be sampled in an undisturbed state, remoulded samples exhibit different behaviour to undisturbed samples, penetration test interpretation methods suffer from uncertainty in their application to many tailings and the tailings gradation changes considerably over relatively small lateral distances and depth. In addition, the process liquor of many Western Australian tailings contains large quantities of salt and other dissolved solids, which can further complicate laboratory test programs. To provide an insight into the variability at a typical gold tailings facility, four gradations of the material were tested to obtain critical state parameters. Historic surficial tube samples were collated and organised by gradation to establish the range of densities typical after settling and air drying. These were then compared to laboratory-accessible densities. Finally, tube samples were tested in the laboratory to observe if the large-strain material behaviour was consistent with the inferred critical state parameters for similar gradations. Site pore fluid was used in the testing of the tube samples in an attempt to assess if the pore fluid modified the critical state conditions of the material.The tube samples tested all exhibited strongly dilative behaviour in undrained shear. Of the four samples tested, only one exhibited behaviour consistent with the inferred location of the critical state line relevant to the material’s gradation. The reasons for the unexpected behaviour of the other three samples include layering within the samples, the potential influence of large quantities of salt in the pore fluid and likely differences in the gradation of the fines components of samples taken from mid-beach and the decant area.CITATION:Reid, D, 2015. Observations on the behaviour of a gold tailings with hypersaline pore fluid, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 191–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Legislation up to the early 1950s prevented the mechanical extraction of pillars. The mines operating at that time had formed extensive areas of pillars. When permission for the mechanical extraction was gazetted, conventional equipment was employed for pillar extraction and generally using hand mining systems. The mid-fifty's saw the of continuous miners. These machines eliminated the disadvantages of conventional equipment and the necessity for multiple working places. Some new layouts for panels emerged; however, actual extraction methods of pillars still followed closely that of hand mining. During the early sixty's the extraction of standing or new formed pillars was undertaken by the "open-end lift" or a "split and lift" method.

Jan 1, 1974

By B Johansson

The mining industry needs to recruit young talented people. An important task therefore, is to create future attractive mining workplaces that engage and motivate young people to work within the industry. Our intention with this article is to illustrate a possible way forward for the mining industry to form such workplaces. We discuss different aspects of an attractive workplace and summarise our findings in a specification of basic demands dealing with safety, physical and psycho-social work environments and social responsibilities.

Nov 22, 2011

Industrial and telecommunications organizations around the world are now turning to optical fibres to satisfy their growing needs for data, voice and video communications and to solve transmission problems in noisy and hazardous environments. Already, coaxial cables have been made obsolete for intermediate and long distance applications and fibres are making in-roads on other copper cable and microwave system techniques.The idea of optical fibres is not new, but techniques to manufacture the high quality cable and components required have only recently been developed. Nonetheless, the technology is now advanced, reliable and mature, and costs are plummeting with increased production and market competition.The mining industry has benefited greatly from developments in electronics and communications over the years. Optical fibres are to have a further significant impact and the time is now right for the industry to begin to exploit the many advantages of this new medium. Applications include data transmission, long distance telecommunications, measurement and control systems, surveillance, computer networks, etc.This paper briefly describes the characteristics of optical fibres, current status of the technology, applications and possibilities for future development.

Jan 1, 1984

By E K. Chiw, S-M Jung, S M. Masuka, ika

The world reserves of high-grade iron ore have depleted necessitating the need to utilise any existing natural iron ore deposits to meet the demands of the world’s expanding economy using hydrogen in the reduction process to curb CO2 emission. These low-grade ores include iron ores with high phosphorus content. The thermodynamic conditions in the blast furnace allow for the reduction of phosphorus that readily dissolves into the molten iron. Phosphorus in the gaseous state readily dissolves into the molten iron and therefore must be removed due to its negative influence on the mechanical properties of steel. The removal of phosphorus from molten iron is difficult causing the phosphorus to concentrate in metallic iron. The aim of this study is to provide basic knowledge on the phosphorus distribution after reduction using the CO-H2 and possibly provide the optimum conditions for phosphorus partitioning into slag, increasing the probability of its removal by magnetic separation. Total porosity, pore size distribution and surface area of the pellets used were measured using a mercury pressure porosimeter. The reduction was carried out using thermogravimetric analyses (TGA). The reduction rate increased with increasing H2 and was highest when 100 per cent H2 was used. Metal elements distribution in the reduced pellet was clarified using electron probe microanalysis (EPMA) and showed that phosphorus was distributed in the same areas as Ca. More phosphorus was concentrated in slag when 50 per cent CO–50 per cent H2 was used, increasing the probability of dephosphorization using magnetic separation. The concentration of phosphorus into slag was related to the rate of reduction. Further investigations into the reduction kinetics of this ore by CO-H2 is suggested to validate these findings. Nevertheless, a comprehensive thermodynamic analysis of the reduction of phosphorus containing phases found in iron ore with carbon, CO and H2 was provided to assist in selecting the optimal reduction experimental conditions.

Sep 18, 2023

By D Will

RedrossThe Redross orebody averages 1 m wide, has a strike of 50 - 350 m, dips at 55° and has a basalt footwall and an ultramafic hanging wall. The most successful and innovative aspects of mining Redross were:•ore development innovations, 90 per cent of development was split fired with a shanty back profile to enable larger and more productive equipment to be used and resulted in higher development grades, improved project payback time and improved ore recovery;•hand held stoping using a multiple level, bottom up ‘V’ shaped hand held stoping method that allowed mining on multiple levels with hand held productivities between 50 and 90 tonnes per shift;•the use of 1 m cement pillars and 7 m high crown pillars were used to create multiple mining areas that enabled high overall production rates from hand held mining this orebody; and•the use of vertical cement pillars to enable hand held mining of adjacent stopes without leaving ore pillars.MarinersThe Mariners orebody averages 3 m wide, has a strike length of 50 - 250 m and dips at 50° with a basalt footwall and poor ultramafic hanging wall. The most successful innovative ideas of re-opening Mariners were:•Dewatering the existing mine workings utilising ‘oilfield’ technology by installing a long submersible pump in on existing pump rising main. This enabled the mine to be dewatered at rates up to 100l/ sec and helped overcome the 45 to 55 L/s inflows.•Overcoming the technical problems associated with Mining N07 ore blocks which had severely deteriorated from being underwater for five years by using reverse firing techniques to improve extraction rates and reduce dilution.•Mass firing a large mining block in the N08 with minimal void space because of deteriorating ground conditions.•Use of a longhole version of the Redross hand held mining method to achieve 100 per cent extraction of the N09 higher grade lenses.

Mar 21, 2011

By C R. Ure

To substantially reduce, if not eliminate, carbon dioxide (CO₂) emissions from ironmaking it is necessary to convert from blast furnace (BF) ironmaking using coking coal as the reductant to direct reduction (DR) ironmaking using hydrogen (H₂) and green electricity. Currently, almost all natural gas (NG) based direct reduced iron (DRI) production utilises iron oxide pellets in shaft furnaces, as opposed to fines in fluidised beds. Also, these pellets are ordinarily produced from high-grade magnetite concentrate, rather than hematite and goethite with typically higher gangue contents. The use of high-grade magnetite concentrate is driven by the preference to melt DRI in conventional electric arc furnaces (EAFs), thereby avoiding the basic oxygen furnace (BOF) for making crude steel (CS). However, in replacing BF with DR ironmaking it is not economically feasible to source enough high-grade magnetite to replace the lower grade hematite and goethite currently consumed. That is not to say that hematite and goethite, or even low-grade magnetite, cannot be used in DR ironmaking. However, their higher gangue content, resulting in higher slag production, requires that the EAF producing CS be replaced with a submerged arc furnace (SAF) that will produce pig iron (PI) for the BOF as does the BF. Here, critical issues to be addressed are, what are the technicalities in replacing high-grade magnetite concentrate with hematite and goethite and NG with H₂ in DRI pellet production and melting? This paper summarises certain relevant published information on DRI pellet research, test work and production together with relevant information on Pilbara ores. It attempts to illustrate the inter- relationship of composition and processing conditions on DRI pellet properties. It is intended to serve as a rudimentary guide to understanding the complexities of formulation, testing, evaluation, production and goethite and offer insight into this challenge.

Sep 18, 2023

By Stewart R, Manson RA, Haig DW, Perembo RCB, Kruman B

Since the advent of plate tectonic modelling, the Ramu-Markham valley has been thought the site of a classical island-arc/conti- nent collision zone. In this interpretation the units south of the Markham Valley are held to be island are / micrcontinental mate- rial accreted to Australia and those north of the valley are thought to represent a separate Finisterre island-arc terrane. Recent remapping by the Geological Survey of Papua New Guinea shows: (1) there is no terrane boundary along the Ramu-Markham valley (2) the Finisterre Volcanics are probably part of either a fore-arc sequence or oceanic plateau obducted onto a microcontinent/ volcanic-arc composite terrane, accreted to the continental Australian plate. A new tectonic model is proposed for northern PNG and involves: (I) Eocene to Late Oligocene subduction below a microcontinent remote from Australia to produce the Sepik are and related intrusives, the Finisterre Volcanics (fore-arc or possible oce- anic plateau), together with the Alife blueschist. (2) obduction of the Sepik arc in Late Oligocene-Early Miocene times over the advancing Australian plate. This resulted in crustal melting, some of the products of which are the Mid- dle to Late Miocene Akuna and Bismarck intrusive complexes of the Maramuni arc. (3) obduction of the Finisterre Volcanics began in Early Pliocene times and continues today. (4) post-Middle Miocene mineralisation is the result of melting after obduction of the Sepik microcontinent.

Jan 1, 1997

By E Villaescusa, C Drover

The stability of access tunnels is one of the main engineering challenges in deep underground mine construction. Many underground hard rock mining operations are now reaching depths where the induced stresses are such that sudden and violent failure of the excavations can occur very soon after construction. The loading conditions on the installed ground support schemes are often underestimated by conventional engineering design methods. Therefore, the actual loading conditions often exceed the installed ground support capacity. This can result in failure of the excavations and, in extreme cases, potentially closure of mining operations amounting to hundreds of millions of dollars in lost production. More frequently, violent excavation instability at great depth causes operational delays, costly and unplanned rehabilitation, as well as risks to worker safety. In order to address this challenge, this paper briefly summarises a modern, innovative approach to the design and construction of mine development at great depth. The process follows seven main steps. The first step is to characterise the rock mass strength, structure and stress. The second step is a stability assessment, which identifies the plausible modes of excavation failure, based on the rock mass characterisation. The third step is the definition of an excavation geometry which is harmonic to the high stress conditions. The fourth step is to prepare a site-specific face destressing drill and blast design which will reduce the potential for rock mass instability during the development construction cycle. The fifth step is to accurately quantify the expected loading conditions on the installed ground support. The method of doing so is uniquely analytical and probabilistic. It is based on the natural mechanical relationships between rock strength, structure, induced stress and the physical characteristics of the instability, including its mass and ejection velocity. The sixth step of the design process is to specify a ground support scheme arrangement with sufficient strength and displacement capacity to exceed the rock mass demand by a safe margin. The final stage is to install the complete ground support scheme using mechanised technologies which minimise the exposure of the equipment operators to unsupported ground at the tunnel face.

Nov 29, 2022

By Radmuller H

The proposed underground mine at Porgera forms an integral part of the Porgera Joint Venture project in Enga Province in the remote Highlands of Papua New Guinea. The total in-situ reserves are approaching 400 tonnes of gold making the Porgera deposit one of the largest in the world. The remote, rugged and inhospitable terrain, recent unstable geological environment and primitive yet socially complex nature of the densely populated local community, combine to make the Porgera project very different to developing mines in Australia. The Porgera project is a challenging and exciting mining exploration venture in the final stages of feasibility study submission and negotiations with the National Government of Papua New Guinea. A 1476 m exploration adit was driven in the footwall of the high grade mineralisation for diamond drilling purposes as part of the evaluations necessary for the feasibility study. Ground conditions encountered have ranged from weak mudstones with high water content, requiring immediate steel set support, to competent intrusives.

Jan 1, 1988