Search Documents

By Chris Nelson

Two pieces of European Union (EU) legislation together establish requirements for protection against risks from vibration at work. The vibration directive1 specifies duties of employers to protect workers from risks from exposure to vibration; the machinery directive2, specifies duties of manufacturers and suppliers regarding the safety of machinery marketed in the EU. This paper discusses both directives and the standardisation programmes that support them. It also addresses the implementation of these requirements in Great Britain. Employers’ duties: the vibration directive This directive requires employers to assess and control risks to health and safety arising from hand-arm vibration (HAV) and whole-body vibration (WBV). Member States were required to implement the directive in national legislation by 6 July 2005. Employers are required to eliminate vibration risk at source, or reduced to a minimum. The duties include: assessing risk and exposure; planning and implementing the necessary risk control measures; providing and maintaining suitable work equipment; providing workers with information and training on risks and their control; and monitoring and reviewing the effectiveness of the risk control programme. Daily exposure exceeding a specified action value triggers a requirement for a programme of technical and organisational measures to minimise vibration exposures and the resulting risk, and the provision of health surveillance. Exposures above a specified limit value are prohibited. When conducting their risk assessments, employers are required to “assess and, if necessary, measure” the vibration exposure of workers, for comparison with the action and limit values. Vibration measurement in the workplace is not expected in all cases and the use of vibration information from equipment manufacturers is specifically mentioned. This provides a link with the machinery directive (see below). Manufacturers’ and suppliers’ duties: The machinery directive The machinery directive, first introduced in 1989, is intended to remove barriers to trade. It puts duties on manufacturers and suppliers who place machinery on the European market to design their products to eliminate or reduce risks to health and safety and to warn the user of any residual risks, providing information required for safe use (for example, operator training, maintenance and selection of consumables). There are specific requirements for minimising risk from vibration in the design and construction of the machine and, in the case of hand-held, hand-

Jan 6, 2006

By J. E. Chilton

A technique for use in underground coal mines measures the response times of machine-mounted methane monitors. This technique uses a calibration cup to deliver gas to the sensor head to measure response times. For comparison, in the current study, response times were measured by placing methane sensor heads in a specially designed test box where they were exposed to an atmosphere containing a constant concentration of methane. Response time readings measured in the test box were shorter than the readings obtained using the calibration cup. The response times measured in the test box were comparable for sensors from three different manufacturers. The effects of dust cap and flame arrestor design on response times were also evaluated using the test box.

By John Kosek

The electrochemistry of carbon monoxide, nitric oxide and nitrogen dioxide was investigated at a variety of electrode materials in different supporting electrolytes. A portable detector for carbon monoxide was developed using a porous gold anode in perchloric acid supporting electrolyte. This detector has two full scale ranges, 0-100 ppm and 0-500 ppm. A portable detector for mixtures of nitric oxide and nitrogen dioxide was developed using a porous silver cathode in sulfuric acid supporting electrolyte. Nitrogen dioxide was determined in the gas stream by electroreduction. The nitric oxide in the gas stream was oxidized to nitrogen dioxide by passing it over Cr(VI) on firebrick. Electroreduction gave the sum of NO + N02. Analog circuitry was used to display the amounts of NO and N02 separately. Two ranges were available for each gas. They were 0-10 and 0-50 ppm for NO and 0-2 and 0-10 ppm for N02.

Jan 1, 1979

By Bureau of Mines Staff

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine venti lation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which ,accounts for a major portion of the market for coal, received further study. Unique power generation systems, inc luding coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jun 1, 1965

By L. L. Hirst

In 1944, the 78th congress of the United States enacted Public Law 290, which directed the Secretary of the Interior, acting through the Bureau of Mines, to furnish industry with basic information and cost data for the development of a synthetic liquid fuels industry. Recently published information with respect to the cost of synthetic liquid fuels processes indicates a wide variation in estimated results. To clarify the results and inconsistencies for the hydrogenation of coal, the Bureau of Mines has prepared preliminary designs and calculated detailed investment costs from which the operating costs to produce 30,000 barrels per day of liquid products, mainly gasoline, by coal hydrogenation were obtained.

Jan 1, 1949

By Hugh Douglas

In the past two years recent increases in silver prices over levels that prevailed for many years have changed supply/demand patterns. On the supply side, a silver mining boom is in progress in the United States and elsewhere. On the demand side, traditional uses of silver by individuals are dropping while industry is conserving. These changes will alter the supply/demand balance and bring about more moderate rises in silver prices, which in turn will impact the mining industry.

Jan 1, 1981

By Dale William Avery

Thirty mines and prospects were studied; 22 are within the Dolus Lakes RARE II area. Three properties within the area and one adjacent to it were determined to have indicated or inferred gold, silver, or molybdenum resources (fig. 1 and table 1) associated with quartz veins and shear zones or quartz-pyrite stockworks in granodiorite. Five other properties in the area and three just outside have potential for the discovery of gold and silver resources. Minor amounts of very fine-grained placer gold are in glacial outwash in and near the area. The John G. Carlisle Mine (fig. 1, no. 9) produced 120 oz (3.7 kg) of gold between 1897-1899. The Independence Mine produced 481 oz (15 kg) gold, 197 oz (6.1 kg) silver, and 189 lb (86 kg) of copper between 1926 and 1935. These mines are adjacent to the study area's northern boundary.

Jan 1, 1983

A vital ingredient in ensuring that metals exploration companies, working in the developing countries of thePacific Rim, support the development of national geologists is making such a learning program cost-effective. There is a wide spectrum of learning needed in the development of these explorationists: the technical and conceptual skills to carry out exploration efficiently, the professional and managerial skills to apply the exploration in the work situation, the personal attributes required to manage their exploration effectively, and a company organisation that allows them to learn and use these skills and attributes.

Jan 1, 1995

By PW Meisel

An hydraulic-powered reel system to minimize peak tension transients in shuttle car trailing cables has been theoretically designed and analyzed using a computer. A single spring-loaded take-up sheave stores or gives up cable to maintain tension within specified limits. Controls have been incorporated to shut down the vehicle before all cable is removed from the reel and to de-energize the cable in the event of a reel/cable jam. Full-scale hardware configuration drawings sufficient for manufacture of a test system have been completed.

Jan 1, 1983

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By Gary Kahn

The knowledge of how and when your explosives go off can help you make intelligent decisions regarding future application of explosives thus removing some of the black magic associated with blasting. The net result will be intelligently set-up shots with timing, explosive charges, and placement more accurately done. Lower operational costs can be achieved when the correct combinations are applied.

Jan 1, 1989

By A B. Christie

Stream sediment geochemical analyses from 140 mining company exploration surveys of the Coromandel, Northwest Nelson, Marlborough and Westland regions of New Zealand have been compiled from open file reports and entered on a database called REGCHEM (for Regional Exploration GeoCHEMistry). REGCHEM is supported by GEOEXPL, a custom-written computer software application which operates under the Microsoft Access relational database management system on a PC-type computer, The data are plotted as maps using the MapInfo geographic information system (GIS) package. Thresholds separating anomalous values from background values are determined using the PROBPLOT uni-variant statistical package, which enables the discrimination and modelling of several populations. Relevant REGCHEM data are being incorporated into a GIS for the Coromandel region as part of ongoing studies to develop mineral deposit and metallogenic models for the region, and to assess regional prospectivity.

Jan 1, 1995

By N. P. Kripakov

The Bureau of Mines has developed a unique new mine design procedure to determine the changing static load distributions imposed on under-ground support structures during the mining cycle. The procedure reduces the complexities associated with analyzing a three-dimensional problem. A combination of the multiple-seam displacement-discontinuity model and a two-dimensional finite-element window model produces refined results for a specific area of interest by assuming displacement compat-ibility between models. Input to the procedure includes the geometry of mined-out areas in up to two adjacent seams, the rock mass characteris-tics of the surrounding geology, the in situ stress conditions, and the mining sequence. The displacement-discontinuity program calculates ex-pected loadings for mine structures affected by the mining cycle and/or by overlying or underlying seams. Pseudoelastic finite-element analysis using a yield-factor approach determines the stability of coal pillars by simulating the degree and extent of nrogressive rib failure and sub-sequent load transfer. Application of the procedure is demonstrated on a field problem. In-duced stress changes predicted from the numerical model analysis are in reasonably good agreement with stress measurements obtained from an instrumented chain pillar affected by remnant workings in an upper seam.

Jan 1, 1988

By Frank E. Cash

The work of the United States Bureau of, Mines is concerned primarily with the prevention of accidents in the mining, petroleum, and allied industries. This report analyzes the fatal accidents in the coal mines of Tennessee and gives the pertinent factors in tabular and descriptive form, with interpretations and suggestions to operators, workers, and the State Division of Mines for the future prevention or reduction of accidents in coal mines. ACKNOWLEDGMENTS This study was made possible through the cooperation of A. W. Evans, chief mine inspector of Tennessee, and his secretary, Miss Hiliary Penny, who made available the department records and assisted in the segregation and assembly of the data.

Jan 1, 1935

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

By R. Leithner

The need/wish to sequestrate CO2is based on the assumption of the International Panel of Climate Change (IPCC), that CO2 maybe the major driver in climatic changes, i.e. especially the anthropogenic CO2emissions due to the combustion of fossil fuels like coal, oil and natural gas will increase the atmospheric CO2-content, which will lead to higher temperatures in the atmosphere. The 0.03% CO2in the atmosphere have a 22% share of the natural greenhouse gas effect of 33 K necessary for life on earth. The main share of 62% has the water vapour in the atmosphere. Only if one concentrates on the greenhouse gas effect of the gases beside water vapour, CO2 becomes most important with 58% influence. In addition there are other influences on the climate like: • Eccentricity of earth’s orbit, precession of orbital plane, obliquity and precession of earth’s rotation axis (Milankovitch’s theory) • Sunspots and magnetic field of the sun • Changing streams in the ocean • Volcanic activities • Distribution of continents on the surface of the earth • Impact of meteorites • Change of insulation by interplanetary dust [Muller, R.A. 2000] etc. To answer the question, if the CO2-content in the atmosphere has an important or exclusive influence on the earth atmospheric mean surface temperature, one should look into history. Figure 1shows the mean temperature of the atmosphere and the atmospheric CO2-content time histories 1 billion years back; no correlation can be found between them. Nevertheless a lot of countries have committed themselves to reduce their CO2-emissions.

Jan 1, 2004

By Terry J. Close

A mineral resource survey of the 940-square-mile (2,434 km2) Hells Canyon study area, which includes Hells Canyon Wilderness, Snake and Rapid Wild and Scenic River's, and adjoining roadless lands in Oregon and Idaho, indicates the area is highly mineralized. Thirty-four lode deposits within the study area have resources totaling about 31 million tons (28 million t) containing copper, silver, zinc, gold, and lead; another 42 lodes, not sufficiently exposed to allow resource estimates, are believed to have mineral potential. The most important deposits are copper-, silver-, zinc-, gold-, and lead-bearing volcanogenic occurrences, followed by silver-and copper-bearing contact replacement (tactite) deposits; other lode occurrences are relatively unimportant. The most important placer deposits occur at Dry Diggins; placers along the Snake River are small and scattered. The study area has extensive deposits of limestone and sand and gravel; it has little potential for energy resources.

Jan 1, 1982

By Steven A. Hawkins

This report details the conduct and results of a 5-month study to collect data on the use of steel support for ground control in European underground coal mines. The report summarizes European steel support design practices and describes the applicability of steel supports to U.S. mining conditions.

Jan 1, 1980

By A. G. Pasamehmetoglu

This paper describes the conver¬gence and load measurements carried out in inclined seams at five longwall faces, two of which were supported by hydraulic props and the other three by conventional timber supports in Karadon-Gelik mine. The minimum support capacities determined in this study are compared with the results obtained from two empirical approaches suggested by Wilson (1975) and Jacobi (1981). The characteristics of hydraulic props to be used and support patterns in the longwalls are found, conclu¬sions are drawn and suggestions are made. Design nomograms are prepared for field engineers, in order to be able to approach the problem more confidently and realistically.

Jan 1, 1992

The occlusion of unliberated gold particles in silicates and sulfides in crushed/milled ore dictates the recovery that can be expected. The grade of this occluded gold in cyanide leach residues shows a consistent, general relationship to the head grade of the ore, irrespective of mineralogy or geographical location. The residue grade almost invariably increases with the head grade, but not in proportion to it. This phenomenon appears to stem from the nature of the geological events originally responsible for creating the ore deposits. A statistically-based technique for determining the true head grade-tail grade relationship from gold plant operating data is described. The effect is illustrated with results from several worldwide gold milling operations analyzed over the last 35 years.

Jan 1, 2008