Search Documents

By R. E. Simpson

Beginning in 1972, fully grouted resin bolts were used in underground mines. An estimated 20 million resin bolts will be installed in 1980 owing to their apparent support improvement in most roof-bolt applications. Inorganic cements were tested to replace the resin at a lower cost while retaining the advantages of a grouted bolt. Although other inorganic materials were considered, all but portland and gypsum cements were rejected for reasons of availability, performance, or cost. Portland and gypsum-type cements were tested by the Bureau of Mines to select a fast-hardening, low-cost material that would anchor a roof bolt adequately to meet safety standards. An alpha-gypsum cement, accelerated with potassium sulfate, was selected as the best material because it had adequate pull strength at a desired set time of less than 5 minutes and was readily available.

Jan 1, 1980

In the present study, we have investigated the conditions for the formation of bubble clusters and the effect of well-defined agitation on the stability of clusters. A specially designed cell was used in which bubble clusters could be formed at the surface of a porous block in a fluidized bed of relatively coarse hydrophobic silica particles. The clusters then rose through a flow field of known turbulent characteristics. The size of the clusters before and after passing through the turbulent zone were measured using a high speed camera. The influence of shear rate on the deformation of the bubble clusters was investigated. The results showed that the Kolmogarov microscale was much smaller than the maximum cluster size, suggesting that the breakage of the clusters was mainly due to interaction with clusters in the inertial convection sub-range.

Jan 1, 2009

By Cheng Lin

The Group Equivalent Pile (GEP) approach was proposed by researchers to analyze a laterally loaded pile group. This approach enables engineers to evaluate the behavior of a pile group in single pile analysis software, such as LPILE. A previous study showed that the calculated results using the GEP approach for piles agreed well with field test data. To evaluate the accuracy of the GEP method for analyzing laterally loaded shafts, two case studies with different shaft diameters were performed in this study. The comparisons showed that the calculated results using the GEP method and considering the contribution of the shaft cap if embedded generally agreed with the measured from the full-scale tests.

Jan 1, 2009

By Martin D. Conyac

A 1984 Bureau of Mines investigation identified ho mineral resources in the Wilderness Study Area (WSA). However, four prospects in the WSA contain anomalous amounts of copper and silver minerals; one had traces of gold. Stratabound copper-silver occurrences appear to be prevalent. Quartz veins in the WSA locally contain trace gold, and one mine adjacent to the area produced some gold in the late 1800's. The WSA is underlain principally by Precambrian and early to middle Paleozoic quartzites, argillites, dolomites and limestones that have been complicated by faulting, generally tilted northeastward, and thrust southeastward over sequences of late Paleozoic sedimentary rocks. The stratabound copper-silver occurrences and gold-quartz veins are in Precambrian and Cambrian rocks in the western part of the WSA, as are similar deposits regionally. Sand and gravel, and limestone are abundant, but plentiful resources of these commodities are nearer established markets. In November 1983 there were 5 small groups of current claims oh the WSA boundary; none are patented claims. Probably less than 35 claims have been located within the WSA, mostly in the northwestern portion; hut over 100 claims have been located outside, near the northwestern boundary. Oil and gas leases nearly surround the boundary and 6 extend up to 1 mile into the study area. There has been no recorded mineral production from within the WSA. From 3 to 5 miles to the west, several lode nines in the Johnnie district have produced several million dollars worth of gold from quartz veins, and some silver and lead from galena-calcite veins. These veins generally trend northeasterly and dip northwesterly and probably do hot extend into the study area.

Jan 1, 1985

By Du Sichen, K. Mukai, S. Seetharaman

Viscosities of slags constitute an important physical property needed for an understanding of the mass transfer phenomena in metallurgical processes. Viscosity is also the key that leads to a better understanding of the structure of slags. It is well known that the viscosities of silicate slags decrease with the addition of basic oxides due to the breaking of the silicate network. The measurements of slag viscosities often pose experimental challenges, especially to the choice of materials. The keynote lecture takes up the experimental problems and the various techniques adopted. Dynamic viscosity measurement, as a powerful tool towards an understanding of the kinetics of some high temperature reactions, is brought out. A number of semi-empirical models have been developed to estimate the slag viscosities in the case of multi component slags. A critical survey of these models is presented in the lecture. Earlier models by Riboud et al., Urbain et al. and Mills et al. have been developed further into a new generation of models. Some of the current important models are (1) Model by Iida et al. (2)CSIRO model (3) Pyro research Model (4) Model by Tanaka et al. (5) Model approach by Reddy et al. and (6) KTH-model. The predictions and capabilities of the various models are compared. Estimations of viscosities from thermodynamic data and prediction of liquidus temperatures from viscosities are presented. The concept of surface viscosities with reference to slags and viscosities of two-phase mixtures are also taken up in the presentation.

Jan 1, 2004

By Xiong Houjin

In the excavation works of some deep foundation pits within the boundaries of Guang­dong Province of China, though some measures, such as steel sheet piles, diaphragm walls, etc. were taken to protect the walls, the construction of the excavation works was often accompanied by damage of buildings and public facilities, surface settelment. sand boil and collapse of piles. When these happened, only chemical grouting could be used as the most efficient measure for rushing to deal with or rescue the emergencies. Besides, the application of chemical grouting protection wall technique also palys a very important role under the geologic conditions of the coastal areas of Guangdong Province, when applied in the mucky oystershell layer wealthy in water and the deep mud layer, it can not only achieve good results, but also reduce the cost significantly. In this paper, we discuss the water-tight and earth retaining functions of chemical grouting protection wall in weak formation, and introduce the applicable ranges of chemical grouting protection wall in the excavation of deep foundation pits. Some technological principles and design considerations of the construction of chemical grouting protection wall are presented. Different types of protection wall are also introduced.

Jan 1, 1991

By David A. Bacca

Hydraulically powered submersible borehole dewatering pumps and emulsion/ANFO blends evolved at about the same time and for the same reasons. Mining operators needed safe, efficient dewatering systems and water resistant products.

Jan 1, 1994

By K. Adham, C. Lee

Over the last forty years, a number of specific fluidized bed applications in nickel extraction have been developed for commercial use. Five important processes have gained particular acceptance, namely, sulphide ore roasting, nickel sulphide (matte) roasting, nickel oxide reduction, laterite ore pre-reduction, and nickel chloride pyrohydrolysis. These applications involve different feed materials and process conditions, however, all benefit from fast reaction kinetics and high heat and mass transfer rates in the fluidized bed reactors. They have been studied, tested, and implemented by various nickel producers, who have published their results in many papers and patents. This paper examines the design issues surrounding the application of fluidized bed technology to the above nickel processes. Based on the available data in the open literature, computerized process modelling is used to provide generic flowsheets that illustrate the key features of each process.

Jan 1, 2004

By J. P. D. Strydom

The transmission of excessive vibration to the human body can cause physical stress that may result in crippling pain or permanent disability. Rock drills are known to transmit high levels of vibration that are difficult to attenuate through conventional approaches to vibration isolation. However, it can be shown that once the ISO frequency weighting has been applied, most of the vibratory effect of the rock drill?s motion is concentrated at the drill?s operating frequency. This observation opens the way for utilizing a concept known as vibration absorption, aimed at attenuating the rock drill?s vibration. In essence this entails using the inertia of a secondary vibratory system to counteract the motion of the handle. This article documents an investigation into the use of such an absorber for attenuating rock drill vibration and demonstrates the feasibility of such an approach. A mathematical model of such an absorbing handle was developed and used for design studies. Based on these investigations an experimental prototype model was manufactured and tested. A significant reduction in vibration levels could be achieved.

Jan 1, 2002

By A. du Plessis

The study summarized in this paper focused on expanding existing South African mine closure cost calculation models to provide a new model that incorporates risks, which could have an effect on the closure costs during the life cycle of the mine. This research is important because currently there are a number of mines that do not have sufficient financial provision to close and rehabilitate the mines. The magnitude of the lack of funds could be reduced or eliminated if the closure cost calculation is done in a more risk-orientated manner. The model consists of an expansion of existing closure cost calculation models, by applying the Monte Carlo risk simulation technique to model influences of external and internal changes affecting closure costs. It is shown that the proposed risk-based model provides a way to understand better the implications of uncertainty on the closure costs.

Jan 1, 2006

By M. Roy

Safety and stability of underground coal mine workings are always in danger when opencast mines are operating in close proximity. A study was conducted to investigate the level of vibration generated from opencast blasting at similar distances on the surface as well as in the nearby operating underground coal mine openings. Eight blasts were performed and nineteen vibration data were recorded on the surface behind the opencast blasting face and also in underground openings at similar distances. It was observed that magnitude of vibration recorded on the surface were more than those recorded in underground.

Jan 1, 2007

By E. De Souza

Two comprehensive surveys, which focus upon backfill practices and the economics of backfilling in underground mines in Canada, have been conducted. The two surveys were designed to assess operational practices and costs associated with the wide scope of filling operations that must be met by individual mines, ranging from raw material feed to the preparation plant, through underground backfill transportation, to in-stope product placement. This paper presents the current state of backfill usage in Canada, identifies trends in minefill practices and provides mine operators with an updated database of information upon which they might compare their own practices and costs with present trends throughout the industry.

May 1, 2003

By H. Saridikmen, C. S. Kucukkaragoz

In the present study, the measurement of sulphur distribution ratios between the slag and metal phases encountered in the ferromanganese smelting has been carried out at 0.83 atm of partial pressure of CO at 1773 K by using classical gas-slag-metal equilibrium quenching technique as a function of composition. The distribution results were employed in calculating the sulphide capacities of SiO2-Al2O3-CaO-MgO-MnO slags in equilibrium with the Mn-Fe-Si-Csatd.-S metal phase. It is shown that the sulphur transfer from metal to slag phase increases with increasing the basicity of the slag. As expected, the sulphur distribution ratio decreases by increasing the silica content of the slag system. The effect of metal composition on the sulphide capacities of the slag as well as on the sulphur distribution ratios between the slag and metal phases have been discussed. Emprical relationships were developed to express the sulphur distribution ratios and sulphide capacities of the above slag system.

Jan 1, 2007

In March 1990, Heritage Mining conducted a 2000 line km high resolution aeromagnetic survey of all its prospects in the Coromandel Peninsula. One of the areas covered was the Onemana Peninsula, situated about 5 km north of Whangamata. Details of location and geology are given by Robson and Stevens (this volume).   The detailed helicopter-borne magnetic and radiometric survey over the Onemana area consisted of 163 line kmÆs of flying, and was carried out in order to assist in the definition of hydrothermal alteration and pre- or post- mineralisation structures. The line spacing chosen was 100 m, flown east-west, with a mean sensor terrain clearance of 80 m. Tie lines were flown north-south every kilometre for levelling purposes. The sensor was a Geoinstruments G-813 proton precession magnetometer in a towed bird, with data recorded using a Geoinstruments G-2000 acquisition system.   The Onemana alteration system is at the northern end of a major north-north east trending structural corridor defined by regional aeromagnetic surveys performed by AMOCO in 1980 (Rabone, 1991). T his structure hosts a number of other extinct hydrothermal systems including Karangahake and Golden Cross. In the Onemana contour plot the predominant north-northeast structures form the boundaries of a large area of subdued magnetism in the southern part of the surveyed area that is caused by intense hydrothermal alteration. This area is about 3.5 km long by 1 km or more wide and contains outcropping sinters and hydrothermal eruption breccias, as described in Robson and Stevens. A number of other structures transect this alteration zone, with strike directions ranging from northwest to north. A northwest feature notably truncates the zone to the south, while the northern end seems to be simi1arly bounded; however as data coverage ends at the coast, this feature is less conclusive.    Two distinctive types of strongly magnetic rock were discernible the contoured data. The strong negative magnetic anomalies the north and west are caused by fresh negatively magnetised rhyolites. This was confirmed by ground follow-up work that showed the rocks to be fresh biotite rhyolites with high magnetic susceptibilities.

Jan 1, 1991

By Magno Rodrigues Ribeiro, Alexandre Cabral Stelzer, Cacio José da Silva, Leonardo Nogueira Ferri, Marcelo Ciminelli Mendes, Christophe Bouché, Marco Aurélio Soares Martins, Evenilson Soprani Lopes, José Xavier da Silva Filho, Sérgio Luiz Dalvi

Since 2001, CVRD is carrying out a modernization project in it’s pelletizing plant’s automation systems, that comprehends instrumentation, control and information systems. In addition, the project includes implementation of advanced control systems, using artificial intelligence techniques, including fuzzy logic, expert systems and dynamic physical models, to increase production, reduce fuel and energy consumption and improve quality. This paper reports CVRD’s experiences in carrying out an optimization project.

Jan 1, 2005

By Jorge Meza

El presente texto señala el diseño de controladores en los hornos de fusión de concentrados de cobre a través de la lógica difusa. Para ello, se simuló dinámicamente el proceso de fusión de concentrados de cobre de un horno de tecnología Isasmelt, incluyendo su actual sistema de control y subsistemas convencionales (PID), para representar sus principales parámetros termodinámicos, y de esta forma, obtener una base de medición. Posteriormente, se desarrolló el sistema de control avanzado con la teoría de lógica difusa, que fue incorporado en el módulo de simulación del horno, para comparar su performance con la del controlador convencional.

Sep 24, 2008

By J. R. Thoenen

[For several years the Bureau of Mines conducted tests on ground vibration t emanating from quarry blasting in an effort to determine an index of destruction for different types of structures. Results of these studies have been published in four Bureau of Mines Reports of Invitations as well as in several articles in the trade and technical press.5/ The first paper (3)6/ discussed the subject in general and gave results s of a few blasting records. Some tentative theories also were advanced. The second paper (4) discussed results s of records made from blasting in a number of quarries.]

Jan 1, 1940

By Guthrie. R. K., H. B. Hill

"INTRODUCTION During the early 1920's world-wide attention was attracted to a group of oil fields (Mexia, Wortham, Currie, Richard, and Powell) later known as Mexia-Powell fault-line fields in Limestone, Freestonne, and Navarro Counties, Tex. Enormous yields of high-gravity oil from the wells in these fields resulted in drilling campaigns that quickly surpassed all previous records for rapid, intensive development of productive areas. The discovery of oil in the Mexia filed in September 1921 was followed quickly by the finding of oil in the Currie field in October. In January 1923 oil was discovered in the Powell field; in February 1924 the Richland field, midway between Currie and Powell fields, was brought in; and in November 1924 oil was discovered in the Wortham field, situated between Mexia and Currie fields. Each of the fileds was developed rapidly: wells were spaced closely and had high initial production; production peaks were reached early in the producing lives of the fields; subsequent decline was rapid, and there was early and rapid encroachment of edge water.In 1927 Bureau of Mines engineers, in their investigations a engineering conditions in oil,completed a preliminary study and published a mimeographed report 4/ on underground conditions in the Wortham field, and in 1928 they reported on production and development problems in the Powell Field. 5/ field."

Aug 1, 1943

By J. R. Thoenen

[For several years the Bureau of Mines has conducted tests on ground vibration emanating from quarry blasting in an effort to determine Fin index of destruction for different types of structures. Results of these studies have been published in four Bureau of Mines Reports of Investigations as well as in several articles in the trade and technical press.5/ The first paper (3)6/ discussed the subject in general and gave results s of a few blasting records. Some tentative theories also were advanced. The second paper (4) discussed results s of records made from blasting in a number of quarries.]

Jan 1, 1940

By R. J. Gochin, M. A. Diaz

A modified Hallimond tube is described which allows the determination of the ultimate recovery R and the flotation rate constant k in a single, continuous experiment. The range of fine particles which can be satisfactorily floated with the modified apparatus can be extended by increasing the length of the bottom part of the tube. Findings suggest that pyrite and arsenopyrite can be separated in alkaline suspension using the so-called F series of collectors. Lime was found to act as a depressant. The collectors operate under pH and dosage control and do not require other depressants. Collectors used in the study were thio-amine (a cationic surfactant) and alkyl propionamide (a non-ionic surfactant)

Apr 1, 1995