Search Documents

By Micheal Mitariten

The recovery of natural gas (primarily methane) from coalbed deposits is an established and growing source for the U.S and accounts for over 7% of its total production. The gas from on-purpose degassing is often pipeline quality and requires only compression and dehydration before being admitted to the pipeline grid. However, the raw gas is sometimes contaminated with nitrogen (N2) and/or carbon dioxide (CO2) that can make the gas inadmissible to the transportation pipeline. In general, the N2 must be 4% or less and the CO2 should be 2% or less. In treating gas produced from virgin coal bed or from degassing operations where CO2 is present, amine systems are traditionally used for its removal. Engelhard’s Molecular Gate® adsorption system offers an attractive alternative due to its skid-mounted equipment, low pressure and unattended operation, cost and high on-stream reliability. Natural gas can also be sourced from the residual coal, after the coal has been mined. This source can be the GOB or gas remaining in abandoned coal mines. This source is almost universally contaminated, often with a combination of CO2 and N2. If the source is from air intrusion, the source can also be contaminated with O2. In treating CO2 / N2 contaminated feeds, the Molecular Gate adsorption system removes both of the impurities along with a level of O2 within a single processing step. To date, ten Molecular Gate units are underway with three systems having been installed for upgrading gas from abandoned coal mines. The technology consists of specialty adsorbents and advanced PSA processes that are jointly offered as fabricated packaged equipment by Engelhard Corporation and Guild Associates, Inc. Upgrading requirements, project challenges and project arrangements are discussed in this paper.

Jan 1, 2005

By G. Stokreef, B. R. Davis, M. Kadiyski, Alvear Montenegro, H-P. Loock, V. Montenegro

An optical probe for burner monitoring in copper flash smelting, first developed at the University of Concepcion, is being industrially tested in a collaboration between Kingston Process Metallurgy, Aurubis AG, and Queen’s University. The sensor uses fibre-optics and optical emission spectroscopy to analyze the light emitted from combusting particles in the furnace reaction shaft. Information that can be extracted from the emission spectrum includes the temperature and brightness of the flame, as well as emission lines or bands from excited atomic and/or molecular species. Laboratory proof of concept testing of the sensor was first completed in a continuously fed drop tube reactor using O2/S stoichiometric ratios between 0.8–4.0. These O2/S stoichiometries capture the industrial operating condition, which is typically less than 1. The results from lab testing justified a plant trial of the optical probe, which was done in the Aurubis Hamburg flash furnace in September 2018. From this trial, approximately 31 hours of spectral data were collected and synchronized with furnace operating data. The results from both drop tower test work and the plant trial are discussed with implications for process monitoring in the commercial furnace. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process. It is used to treat copper sulphide concentrates and small amounts of secondary materials, such as dust generated by the process. O2 enriched air and the concentrate blend are fed into the furnace reaction shaft through the concentrate burner. As the particles fall through the reaction shaft, they heat up and ignite, causing rapid, exothermic reactions that oxidize the iron sulphide, some copper sulphide and impurities in the feed. Reacted particles fall into the settler of the furnace, melt and separate into a matte and slag, while the SO2 enriched off-gas is carried out of the furnace for heat recovery and H2SO4 production. Operation of the furnace is achieved by adjusting a limited number of control variables. The main variables are the blast feed rate, blast oxygen enrichment, SiO2 flux feed rate and CH4 combustion rate (CH4 is used when the chemical energy of the concentrate is low) all measured relative to a set feed throughput. (Davenport & Partelpoeg, 1987; Davenport, King, Schlesinger & Biswas, 2002) The batch tapping nature of flash furnaces makes operation difficult because these control variables impact each other, and product quality can only be measured when matte and slag are tapped from the furnace. This means that operation of a furnace is based on feedback control from matte and slag assays. Because of the time-delay associated with understanding product quality, there is interest in using technology to monitor the combustion reactions that happen in the furnace reaction shaft.

Jan 1, 2019

By Harry A. Schrecengost

The Bureau of Mines has found considerable lack of uniformity in style and content of record books used for reporting the results of examinations made by coal-mine officials. These books range from elaborate forms designed for specific examining and operating procedures at certain large mines to simple composition books, tablets, and pocket-style notebooks at other mines. Examination of thousands of these record books discloses that the reports of many examinations are so brief and so poorly worded that they cannot be understood readily. The contents, in some instances, appear to be deliberately ambiguous. The value of keeping accurate accounts of safety inspections in coal mines is often underestimated. Well-kept records reflect managerial attitude and indicate well-governed operations as well as training of official personnel to conform to considered policy and regulations and if necessary, may serve as documentary evidence to protect the mine officials and the operators.

Jan 1, 1962

By Han Yi

The coarse indium ingots produced by Shaoguan smelter contained a lot of impurities. In order to produce the high pure indium with the purity more than 99.99%, the appropriate refining processes were designed and the practice of combined application of Glycerin-KI process and electrolysis in Shaoguan smelter was introduced.

Jan 1, 2005

By N. W. Byrne

THE study of diamond drill results at the Lake Athabaska property of Athona Mines, Limited, and the co-ordination of information secured, has demanded extensive application of methods for interpreting true conditions, both structurally and from the point of view of ore outlook. This work was in charge of a capable engineer, who, as the result of exhaustive study of the drill cores, has been able to issue maps and plans exceeding the expectations of the majority of engineers and geologists who visited the field during the past summer (1935); that is, having in view the fact that staking of the property had been completed but a few months beforehand and that geological conditions were practically unknown up to the time drilling began in April. The following pages present an outline of the work of the assay and engineering offices in co-ordinating and interpreting the results of the drilling. The writer desires to acknowledge the suggestions offered by A.P. Beavan, geologist and engineer at Athona Mines, whom he assisted during the drilling campaign, and also the co-operation of the drilling contractor's employees. The geological map, mine plans, and forms accompanying the paper are from the Company's engineering office files.

Jan 1, 1937

By G. Denton, P. den Hoed, A. Luckos

The potential application of fluidized beds in several sectors of the ferroalloy industry is promising. They can be used in the direct reduction of iron ores to produce a feed for steelmaking, in the reduction of manganese dioxide to produce a lesser oxide for feeding to smelters, in the preheating of chromite for the production of ferrochrome, and in the calcining and pre-reduction of nickel laterites for the production of ferronickel. This paper discusses the potential of fluidized beds in theses processes and highlights the advantages of the technology over other technologies, such as rotary kilns. Two primary advantages?(1) that fluidized beds can treat fine materials and (2) that fluidized beds can be integrated with smelters in a way that allows for more efficient use of energy?may well see the technology gain prominence as more deposits of lower grade are mined and industries strive to use their resources more efficiently. In discussing the potential of the technology in the ferroalloy industry, this paper focuses on the application of fluidized beds in the smelting of chromite, nickel laterites, and manganese ores. Central to the successful operation of this technology is a knowledge of how particle properties influence the behaviour and design of fluidized beds.

Jan 1, 2007

By R. Stefanko

This first Annual Report covers the work on Contract No. H0377043 "Cable for Face Equipment", from August 1, 1977 to July 31, 1978. It reports the progress in the three areas of over-and short-circuit protection, cable ampacity research and cable couplers. Field trips have established many interesting facts related to circuit breaker settings and cable size. For example, the determination of cable sizes depends on the RMS duty cycle current determined by a particular piece of equipment, but the actual selection of the cable to be used is often a function of the maximum allowable circuit breaker instantaneous settings as specified in Title 30. In order to avoid nuisance tripping as a result of instantaneous starting current field, laboratory and analytical studies are being conducted to determine proper settings and cable sizes Also an extensive program has been established to monitor the performance of high voltage cable couplers and determine their modes of failure. Various equipments are being designed for laboratory testing, and an extensive reeled cable experiment is also under way.

Jan 1, 1978

By Leonard Obert

This report presents evidence indicating that when rock is stress-relieved during the course of mining or in drilling a core, it may be altered or damaged to the extent that the physical properties of the relieved specimen are not the same as those of the in situ rock. Furthermore, this type of damage may result from stress change other than that accompanying stress relief, such as the application of a relatively large compressive stress. In some instances the damage is microscopic, manifesting itself as incipient cracks or the failure of individual crystal bonds. However, if the sample is taken from a high-stress area, macroscopic damage may occur.

Jan 1, 1962

By R. J. Pine, J. S. Coggan

Distinct-element modelling has been used to study the mechanisms associated with observed deformation of the western face of the quarry. A complex failure mechanism involving distinct planar surfaces that was proposed for a slope failure in 1967 has been modelled and shown to be plausible. In addition, deep-seated flexural toppling may contribute to the slope instability. Modelling has confirmed the detrimental influence of a raised water-table on the stability of the slope and also indicates that the observed cyclic opening and closing of tension cracks may be attributed to seasonal rise and fall of the groundwater level

Apr 1, 1996

By Holger Witthaus

Beside the traditional geomechanical evaluation methods the geotechnical parameters are recognized as important facts of the planning work for multiple seam mining. Standards for applied monitoring and investigation methods for geotechnical determination of drill cores, laboratory rock-tests and observation of roadheadings are the basics for rock mechanics classification and support design. The geomechanical classification is in this context an essential element. The planning procedure, as it is becoming more and more detailed, beginning with the panel layout up to the technical instructions of roadway development and design of roadheading machinery, nowadays uses a lot of geotechnical information that also are expanding to include quantitative determination of more parameters. The current monitoring system includes the description of separation planes using drill cores and roadheading observation as well as laboratory tests of rock-strength and geophysical borehole examinations. This information is analyzed within the geomechanical standard-classification. The re-engineering process of comparison the predicted support success to the actual monitoring results provides the opportunity for continuous optimization of the planning work und support design. This way of empirical analysis is used for basic planning work in Germany for decades. But using the technical standard of information technology and a centralized database now it is possible to reach quick-win effects in implementing research results on the one hand and actual experiences on the other hand.

Jan 1, 2006

By Ali Porbaha

In today's fast-track construction environment, owners are searching for non-conventional technologies to build their projects faster and safer while maintaining traffic flow during construction. To that end designers and contractors are providing solutions that incorporate many unique features to expedite construction processes. In addition to timely delivery of the finished highway products, there is an increasing interest in making the initial investment in applying innovative technologies and thereby minimizing costly maintenance of highway projects. Accordingly, the aim of this paper (along with the accompanying paper) is to examine innovative technologies, developed mostly in Europe, that accelerate construction of highway, runway and railway embankment foundations. For each technology, a basic concept, installation technique(s), and design considerations are discussed, along with the case history of a real-world project. The Geotextile Encased Columns (GEC), AuGeo, and Continuous Flight Auger (CFA) are presented in Part I. Deep Mixing (DM), Mass stabilization, Cut-Mix-Injection (FMI), and Combined soil Stabilization with Vertical columns (CSV) technologies are discussed in Part II.

Jan 1, 2002

By Richard Miller

RECENT studies of creep have made it apparent that plastic deforma-tion may occur in metals under stresses less than the elastic limit as deter-mined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapsell1 said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a. definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was deter-mined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instru-ments by A. W. Hanson4 on zinc and by Podaschowsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc.

Jan 1, 1936

To improve the air quality in large-opening stone mines by developing better ventilation techniques, including appropriate fan selection in conjunction with air-coursing methods. Background Stone mines are the most common underground large-entry mines in the United States. Data from the Mine Safety and Health Administration (MSHA) for the year 2000 indicate that there were 162 active nonmetal underground mines in the United States, of which 117 were stone mines. Many underground stone mines are drift mines developed from previous quarry operations. Typically, these room-and-pillar mines have entries that are 20 ft or higher and at least 40 ft wide. These large dimensions lead to a very small ventilating pressure loss, even when significant air quantities move through the mine. This is especially true of drift mine operations where ventilating pressure losses of <0.25 in w.g. are common. Underground stone mines with shafts that are<200 ft deep typically have ventilating pressure losses that are <2 in w.g. The pressure losses through these mines are much lower than those of a typical coal mine or deep metal/nonmetal mine. Therefore, the ventilation techniques and principles are quite different. In addition, because of new MSHA regulations that limit the concentration of diesel particulate matter, these mines may need to greatly increase their ventilation airflow. Therefore, large-opening mines need a fan that can move large air quantities and operate at low static pressures. There are three fan types for mine ventilation: centrifugal, axial vane, and propeller. Centrifugal fans are uncommon in underground stone mines as they are often associated with mines requiring the highest of ventilation pressures. Axial vane fans are widely used in all types of mining operations. They are the most common fan type currently found in underground large-opening stone mines. However, they typically do not operate at low static pressures with high efficiency. Propeller fans are currently uncommon in underground stone mines. They are designed for low static pressures and large air quantities at higher efficiency. This fan type best suits the ventilation needs in large-opening stone mines?they produce large air quantities at low pressure losses. Mines with air shafts<100 ft long and at least 12 ft in diameter have fairly low mine static pressures and may also benefit from propeller fans.

Dec 1, 2002

By Steve Kral

Borates are minerals that contain boron. Trace amounts exist in rocks, soil, water and people. Boron-containing ores are rare and U.S. Borax, a subsidiary of Rio Tinto Borax, controls one of the world’s two world-class borate deposits. Through its global systems of mines, refineries, ports, sales offices and distribution centers, the company supplies nearly 45 percent of the world’s demand for borates. Borax has been mining borates in California for more than a century. This year the company celebrated 131 years of continuous business in the Golden State and 76 years at its operations in Boron, the site of California’s largest openpit mine. It also has mines and refineries in Argentina, refineries and ship-ping facilities in Europe and technical staff in the United States, North and South America, Europe and Asia Pacific. So, with the 130±years of borate mining and processing experience behind it as well as its global marketing and distribution centers, there is very little that Borax does not know about borates.

Jan 1, 2003

"Geoscan is used for multi-elemental analysis of conveyed bulk materials in the minerals industry with proven performance and demonstrated paybacks of weeks or months in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering, mineralogy and dust levels. Increments of typically two minutes are accurately measured and provide the plant operators with tonnage weighted results of contained elements. Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Crushed ore increments can be diverted based on composition, such as diverting waste for disposal or marginal material to a stockpile for separate processing. Bulk sorting allows material to be placed into relevant stockpiles for subsequent blending to achieve consistency for process feed. Parameters used for decisions may be primary metal content, deleterious component content, other process parameter, or a combination of these. Process parameter may be the elemental ratio between critical components, e.g. Cu:S ratio, basicity, or the content of an “indicator” element (such as Si indicating material hardness). Benefits will be discussed based on case studies in copper and iron ore.IntroductionAs operators of process plants strive to remain competitive as capital and operating costs increase and commodity prices fluctuate, more focus has been directed at incremental performance improvements at incremental cost rather than major expansions to increase output. The philosophy of working smarter allows plants to adopt technologies proven in other industry sectors to minimise risk. This paper discusses one such technology that the minerals sector is adopting and has found to be safe, reliable and accurate with paybacks of weeks in most applications. New applications continue to be found and major benefits realised at various stages in the processing and handling of ores and products."

Jan 1, 2016

By H. R. Hanley

The characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previosly ously in the literature.&apos; This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors1 previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (I) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calciurn-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent. * Professor of Metsllurgy, Missouri School of Mines. t Professor of Metallurgy and Ore Dressing, Hea.d of Department, Missouri School of Mines. Assistant Professor of Metallurgy, Missouri School of Mines. 1 Among others, see C. G. Fink and Li Chi Pan: Insoluble .Anodes for the Electrol-ysis of Brine [Trans. Amer. Electrochem. Soc., (1926) 49, 83-1341 and other papers by these authors. U. CJ. Taintori, 8. G. Taylor arid H. P. Ehrlinger: Lead Alloys for Anodes in Electrolytic Production of Zinc of High Purity. Truns. A. I. M. E. (1929) 192-200. 2 H. R. Hanley, C. Y. Clayton, D. F. Walsh: Investigation of Anodes for Production of Electrolytic Zinc. Trans. A. I. M. E. (1930) 275

Jan 1, 1931

By C M. Evans, D Thomas

Solid EnergyÆs Wangaloa open cast coal mine was operated between 1945 - 1989, and remained closed and disused until 2001 when SENZ initiated a mine rehabilitation programme. It is nearing the final stages of physical and environmental rehabilitation, aimed at creating an aesthetically pleasing and useful landscape. The final goals of these efforts are to produce an area, which has recreational and educational value. SENZÆs holistic approach to rehabilitation has been undertaken, treating the entire historical mine footprint instead of focusing only on those disturbed areas and the minimum range of issues just to meet with legal compliance. Rehabilitation at the site has included overburden modification with an emphasis on stability, removal and replacement of unhealthy and invasive plant species, and an AgLime amendment to alter soil pH conditions, which would support native plant species. To date, most ongoing activities relate to final planting and plant upkeep, and maintenance of the landform including ongoing erosion control, pest control, environmental monitoring, and research. Environmental quality concerns at the site may be treated by using a combination of methods, including regrading and capping of acid-generating pyrites, soil treatment with AgLime, and passive wetland treatment within existing water courses. Following major works, the mine site area may be opened to the public for recreational activities, interpretive displays on historical mining activities, and observation and appreciation for otherwise unseen geological features. SENZÆs holistic approach to reclamation, rather than treating minor issues, will result in the former mine site being transformed into an asset and the environmental and financial liability associated with the closed mine being discharged. Former mine sites can be turned from environmental liabilities with no recreational or public value (and potentially dangerous to life) into sites that can be safely used by the public for recreational and educational purposes.

Jan 1, 2006

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By B. S. Terry, C. L. Harris

Reduction kinetics from slags containing CuO(0.5), ZnO, PbO, NiO and SnO into a Cu-based metal phase were subjected to computer simulation using a previously developed model for the kinetics of metal-slag-gas reactions that assumes mass-transfer control in all phases. The effects were examined of changing bulk Fe oxide activity, gas reducing potential, temperature, Fe content of the Cu phase and metal/slag ratio. The results permit practical conclusions to be drawn about industrial slag-cleaning practice, but the model is still limited in terms of thermodynamic inputs and the idealisation of reaction conditions

Aug 1, 1995

By Ahmad F. Souri, Murad Abu-Farsakh

"In this study, the static lateral resistance of vertical and battered pile groups was analyzed using 3D finite element analysis. The battered pile group finite element model was verified using the results from a case study performed on the M19 pier foundation of the I-10 twin span bridge in Louisiana. The vertical pile group model was created by adjusting pile inclinations of the verified battered pile group model. The finite element models utilized nonlinear constitutive models for materials behavior and a soil-pile interface model. The results showed that the battered pile group had greater lateral resistance than the vertical pile group with 60-70% lower pile cap displacement. The largest lateral load share was found in the middle rows in the battered pile group, while it was in the leading row for the vertical. The soil resistance profiles showed that the vertical pile group mobilized greater soil resistance compared to the battered pile group.INTRODUCTIONThe lateral resistance of a pile-soil system depends on both pile stiffness and soil reaction. The soil reaction is a nonlinear function of deflection, depth, pile stiffness, and soil stiffness and strength. The lateral capacity of single piles is evaluated at the maximum deflection limit, and can be predicted using established methods such as the p-y curve method (e.g., Matlock 1970, Reese et al. 1974), elastic solution by Poulos and Davis (1980), the strain wedge model (Ashour et al. 2004), and the finite element method (e.g., Yang and Jeremic 2002, Comodromos and Pitilakis 2005, Isenhower et al. 2014). For pile groups, the lateral capacity of a pile-in-group is less than the isolated single pile case because the soil in front of the pile-in-group is weakened by the overlap of stress zones from surrounding piles. The latter is referred to as the shadowing or group effect (Fig. 1). Prediction of the lateral capacity for pile groups is based on the p-y curve method for single piles with the use of empirical factors called “p-multipliers”. The p-multipliers accounts for the shadowing effect, and are a function of pile-pile spacing and soil type (e.g., Brown et al. 1987, 1988, McVay et al. 1995). Moreover, the lateral capacity of pile groups is also influenced by vertical load, piles arrangement, and slenderness ratio (e.g., Rao et al. 1998, Patra and Pise 2001, Ilyas et al. 2004, Hussien et al. 2012).Battered piles refer to piles installed at an angle with respect to the vertical to increase their lateral capacity. The greater lateral resistance is achieved by the additional axial reaction in the pile. Battered piles are called “negative battered” when inclined in the load direction, and “positive battered” when inclined opposite to the load direction (Fig. 1). Previous studies concluded that the lateral resistance is highest in positive battered piles followed by negative battered and vertical piles, respectively (Murthy 1964, Meyerhof and Yalcin 1993, Zhang et al. 1999)."

Jan 1, 2017