Search Documents

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By Gupta R. C

Direct reduction of iron ore by solid reducing agents have been studied extensively and summarised by several authors (Otsuka and Kunii, 1969; Abraham and Ghosh, 1979; Frauhan, 1977; Rao, 1971; Kawasaki, Sanscainte and Walsh, 1962; Ghosh, 1970; Rao, 1979). While studying the reduction behaviour, it is generally agreed that the reduction occurs via gaseous intermediate, generated by carbon gasification reaction which involves mass transfer, heat transfer nucleation and growth, etc through a) reduction reaction occurring at solid reductant, and b) reduction reaction occurring at solid iron oxides, thus making the overall reduction process very complex in terms of clearly defining the reduction kinetics of the system. In addition to this, practical difficulties like correctness of reaction temperature, (Seaton, Foster and Velasco, 1983) difficulties in isothermal temperature studies of reduction, difficulties in monitoring the reduction process while using gaseous reductants and separation of reduction by volatile matter from overall reduction process make the reduction kinetics more complex (Misra).

Jan 1, 1999

By James M. Franklin

Research on modern hydrothermal systems provides quantitative measures of the processes of formation of hydrothermal fluids and of precipitation mechanisms from them. Studies of ancient deposits provide new information regarding volcanological processes that are related to the deposits, as well as data on their spatial and temporal compositional variations. Mew exploration guidelines result from both aspects of research. The most fundamental requirement for large metalliferous hydrothermal systems is an abundant heat supply for the upper two kilometers of the crust. This heat may come from a focused heal source (shallow-level subvolcanic intrusion), but ambient heat also may have provided enough energy for the reactions necessary to effect leaching of metals, especially where heat flow is particularly high (i.e. very large or high-temperature magmatic source, such as ultramafic environments). For most VMS systems, the majority of the metals were derived through leaching from footwall strata; in addition interstratal fluids may enter subvolcanic intrusions during episodes of magma a chamber "cracking," engendering some '?magmatic" component in the hydrothermal system. Direct contributions of metalliferous magmatic fluid also may be significant from arc-related or back-arc felsic or alkalis systems. These latter contributions may form exceptionally high - grade portions in some deposits. Subvolcanic intrusions, which are excellent indicators of high heat flow and may have been the direct driving mechanisms for some stems undergo two stages of alteration: On intrusion emplacernent. fluids may rapidly enter and react with their mesostatic portions, evident in the sills in the Middle Valley. High temperature interactions caused albitization and destruction of oxides and sulfides, releasing metals. During terminal hydrothermal stages, the metalliferous fluid collapsed into the intrusions, forming disseminated and vein sulfides.

Jan 1, 1998

By W. R. Green, B. W. Barde

"Geological exploration involves the collection and analysis of a wide variety of information. A basic problem in interpretation is to determine the interrelationship s of the different data. A number of statistical methods can be applied to this problem, provided that subsets of data can be selected.We have recently developed a set of interactive computer programs which provide the cap ability to quickly examine a large set of data, and may be used by people with little previous computer experience. There are two main stages in using this system. First is selection of subsets of data , by applying various tests on the values of given items. This includes matching specific entries in descriptive fields, and minimum - maximum tests on numeric fields. The second stage is basic statistical analysis and data display , including histograms, 2-D scalier plots, probability (cumulative frequency) plots, and correlation matrices. All output can be viewed on a computer terminal, and important parameters changed to produce the most effective display for use in interpretation.This system has been applied to a number of different exploration problems. An example was the determination of the nature and extent of mineralization of a gold prospect in the Queen Charlotte Islands, from drill-hole data. With the aid of the computer programs , a mineralized zone was defined, and locations for further exploration identified."

Jan 1, 1984

By G. Danko

MULTIFLUX, a new thermal, hydrologic, and airflow model and software is being developed to solve the flow of heat, moisture, and air in and around an underground opening. MULTIFLUX couples two distinct domains that are solved separately first and re-coupled as an iterative task: (1) the rockmass, and (2) the airway. The airway is solved with a lumped-parameter Computational Fluid Dynamic (CFD) module which is an embedded part of the MULTIFLUX code. The CFD model includes convection, conduction, and radiation for heat, as well as convection and diffusion for moisture transport in an air-filled opening. The CFD model also solves for the airflow field. The surrounding rockmass model may be from any analytical solution, or from a complex thermal-hydrologic numerical model such as NUFT or TOUGH2. The rockmass model is interfaced to MULTIFLUX using a novel technique called Numerical Transport Code Functionalization (NTCF). The method provides fast convergence on a personal computer platform. The paper reports the results of MULTIFLUX simulations for a mine drift, comparing calculations with a known mine climate software, CLIMSIM, and with measured data. Through this validation example, the performance of MULTIFLUX is demonstrated. The results show excellent agreement due to the use of realistic modeling assumptions and boundary conditions.

Jan 1, 2009

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill, considering mainly the role and specifications of the fill used but including û brief description of fill preparation and placement. Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. Results of a fill research program conducted by the author in Mount Isa since early 1968 are presented, involving both Portland cemented hydraulic fill and alternative, cheaper, additives for cementing hydraulic fill.

Jan 1, 1971

By W. de Beer

We present aspects of one of several ongoing case studies used in the development of prediction techniques for major seismic instabilities. The current investigation centres on accelerated coseismic deformation described by the kinematics of failure and on softening, as well as the characterization of areas of interest by measures of the seismic response at such sites.

Jan 1, 1998

By Carlos A. Prato, Federico Pinto

"ABSTRACTThe design of drilled shafts often incorporates large factors of safety, for which settlements under service loads are highly influenced by the initial elastic stiffness. In the case of groups of drilled shafts with typical spacing, the elastic shaft-soil-shaft interaction dominates the behavior even for loads close to the bearing capacity, for which the initial stiffness is a key parameter in the design. This paper describes typical trends in results obtained by means of different approaches currently available in the literature for the evaluation of the initial stiffness of a single shaft. An experimental technique that provides a rapid and inexpensive means for the evaluation of the initial stiffness is described, and the results obtained for typical cases are compared with analytical predictions.IntroductionThe behavior of drilled shafts under axial loads is generally governed by the initial stiffness, as the factors of safety considered in design are often large, due to a superposition of conservative assumptions on soil properties and expected loads. In the case of shaft groups, the initial elastic stiffness plays a major role together with the elastic group effects, as nonlinearities tend to localize around the shafts and have a lesser effect than elastic deformations on adjacent elements (e.g., Leung et al., 2010). An accurate characterization of the initial stiffness is thus warranted for the analysis of drilled shafts and shaft groups under service loads.Initial stiffness of shafts may be estimated on the basis of soil stiffness and structural properties of the element by means of numerical methods (e.g., Pinto and Prato, 2006), as well as analytical methods (e.g., Randolph and Wroth, 1978). The soil stiffness may be determined by means of geophysical tests (e.g., Spectral Analysis of Surface Waves, SASW, Stokoe et al., 1994), or correlations with Standar Penetration Test (SPT) blowcounts or Cone Penetration Test (CPT) resistances (e.g., Sabatini et al., 2002).The initial stiffness may also be measured on drilled shafts by means of load tests. Static load tests (SLT), however, have some limitations on measuring small deflections, for which the initial stiffness is often extrapolated by means of large strain measurements (e.g., Chin, 1970), where the SLT measurements are more accurate."

Jan 1, 2014

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that contains between 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

In order to deliver a quality shotcrete and concrete product underground for the extensions to the Cullinan Diamond Mine operations it was decided to develop a new, simpler concrete product to meet underground support requirements. The aim was to develop a concrete product that not only reduced costs but also met the performance criteria of the current range of concrete products used on Cullinan Diamond Mine, a 25, 45 and 60 MPa concrete and a fibre reinforced wet shotcrete. The concrete product batching and delivery system was to be from surface as opposed to the current underground batching systems. The operational principle was to include an automated surface batching plant with delivery of the concrete product to a borehole containing suspended pipelines delivering to an underground storage facility from where the product is delivered to the working area by further pumping or agicars. Keywords: concrete, shotcrete, full flow, frictional loss, pipeline transport, positive displacment pump

Jan 1, 2006

By H. K. Lin

Deepwater discharges of sulfide flotation tailings have been practiced for several decades. Oxygen penetration and organic matter content in such environments are the two major factors that determine their reduction-oxidation condition and hence the rate of sulfide mineral dissolution under such discharge environments. In this study, the effects of solution redox potential and pH on the dissolution of some heavy metals from sulfide flotation tailings were examined. Zn, Pb and Cu concentrations in solution were all higher at a higher redox potential and lower pH. Dissolved Zn concentrations reached 100 ppm even at a low redox potential of 105 mV and near neutral pH after 33 days. Pb concentrations were below 2 ppm at 105 mV and near neutral pH after 165 days. At 105 mV, the Cu concentrations were below 0.2 ppm at near neutral pH after 165 days. At pH 2.3, the Fe concentrations were higher at 420 mV than at 105 mV. But at pH 6.8, the Fe concentrations were lower at 420 mV than at 105 mV, due to the oxidation of Fe2+ to Fe3+ and the subsequent precipitation of ferric hydroxide. Arsenic concentrations in solution were all less than 0.002 ppm. For Zn, Cu and Fe, no significant differences were observed between the tests in solutions prepared using seawater and those using distilled water. However, Pb concentrations reached higher levels in solutions prepared using seawater.

Jan 1, 2009

By G. L. Fitzpatrick

Preliminary results of an experiment in seismic holography indicate that the techniques of acoustical holography may be successfully used with seismic waves to determine the size and general shape of underground objects. This experiment was carried out under field conditions on a moderately large scale compared with the typical laboratory experiments in acoustical holography. The object to be mapped was a 100-foot-diameter, spherical, low-velocity zone of explosively fractured rock in oil shale at an average depth of 80 feet. The seismic wavelength of the Fourier component wave used in making the seismic holograms was 50 feet at a frequency of 140 cps. The hologram sampling aperture was 226 feet square and was sampled by 441 geophones in a 21 by 21 rectangular array. One novel aspect of the experiment was the use of a wide-band polychromatic explosive source of seismic waves rather than a narrow-band quasi-monochromatic vibrator source. A successful laser reconstruction of the object image from a lensless Fourier-transform hologram in the form of a 5/l6-inch-square photographic transparency is illustrated. The size of the underground object measured from the laser reconstruction of the object and the size inferred from a knowledge of the amount of explosives used to fracture the site and the tensile strength of the oil shale are found to agree.

Jan 1, 1972

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By Wouter Hartman

Xuandong Coal Mine is mining coal in one of the most challenging underground environments in the world. This work has found that it is not only challenging but it also has the composition for some interesting rock mechanics and ground control conditions. The paper highlights the extreme mining and rock mass behavior conditions encountered when mining coal at 900 m below surface. It was found that the ground control environment associated with geological weakness, low coal material strength and stiffness, was reasonably well controlled; however, the chain pillar geometry and design did not take these geological weaknesses into consideration. Some of the chain pillars employed were quite large, which resulted in floor punching and secondary floor heave, which causes extreme difficulty for production. No barrier pillar has been employed except for the center 164-m-wide main headings pillar with a w/h ratio in excess of 40. After assessing the location and geometry of a 200-m-thick dolerite sill overlaying the coal measures, we found the probability of it breaking up into to smaller fragments and producing a larger goaf to be low. Therefore, the influence of the dolerite sill on chain pillar loading is considered small compared to the low coal, immediate floor and roof rockmass strength. It is further recognized that horizontal stresses could be locked up within the dolerite sill, which would likely result in regional bending that would be distributed through the chain pillars. This has, to some extent, already occurred, and the effects have been seen and felt through excessive floor heave, pillar punching, and coal bumps (seismicity). We?ve also found that there was a need to employ basic rock mechanics principals in assessing the stability of future multiple seam mining layouts.

Jan 1, 2012

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

By H M. Ahmed, W S. Dunbar

Construction of cave mining systems requires significant capital expenditure and long-term commitment of human, equipment and material resources before production commences. Risks and uncertainties of these large-scale mining projects are significantly higher than for small-scale projects. This is due to the complexity and interactions of the construction schedule components and the large scale and uniqueness of such projects. One way to successfully manage construction uncertainties that would lead to schedule delays is to include a reasonable cost contingency in the budget estimation. A real options approach based on the least-squares Monte Carlo (LSM) method is used to estimate cost contingency associated with schedule uncertainty in mass mining projects. Cost contingency is estimated as the cost of potential project crashing (acceleration) decisions, which pays for not extending the schedule. While such a significant undertaking is expected to be subject to some delays, these can have an enormous impact on the economic value of such projects. The value of the crashing option was explicitly formalised into the process of valuation, as it is assumed to be a single option being considered in the valuation at every decision point prior to the construction completion date. As a part of the proposed method, a stochastic function for the percentage of remaining scope of work for the remaining duration of the entire project was integrated into a framework of numerical simulations. This ensured that this function can implicitly account for sources of schedule uncertainties for projects represented by multiple and overlapping work packages. The LSM method was applied to a real case scenario in an operating block cave mine, with modified scale and features. The results yielded by the LSM method indicated that significant changes in capital budget allocation stem from variation in a contractor’s risk perception and confidence level of estimated delays.CITATION:Ahmed, H M and Dunbar, W S, 2016. Budget estimation and contingency allocation of block cave construction using least-squares Monte Carlo real options, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By N. Simpson

Low carbon 11.5% chromium stainless steels are finding increasing use in industry as square or rectangular tubing material for the construction of structures by welding. During processing, resistively welded circular pipes are bent into square or rectangular shapes. During this process longitudinal cracks can sometimes develop atone of the inner corners of the section. An investigation has shown that the processing of round into square tubing with very sharp corners can cause excessive cold working at the inner corners of the squared tube. This, together with the high tensile residual stresses and a susceptible microstructure due to the presence of grain boundary carbides, can result in brittle cleavage cracking. Measures that can be used to reduce the problem are described.

Jan 1, 2003

By Wolfgang Guetter, Wolfgang Weber

The upgrading project for two hydropower plants in Slovenia, Europe, requires two new pressure tunnels: Plave II (5.9 km Flysch) and Doblar II (3.6 km Limestone). It is the worldwide largest application of the Double-Shield TBM technology combined with an extremely thin-walled monoshell honeycomb lining system. The first drive has been completed by end of June 2000 achieving best performances of 50m/d and almost 1,100m/mth. In September 2000 the TBM started the second tunnel without any required adjustments due to geological or other reasons. Another 52m/d have been bored already within one production day of two 8 h shifts achieving a maximum penetration rate of more than 6m/h. The completion of the Doblar drive can be expected by February 2001.

Jan 1, 2001

By Ailton da Silva Ferreira

Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of curaua fibers. Both TGA and DTG curves were analyzed to determine the effect of the curaua fiber on the thermal resistance of the composites. It was found that the curaua fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.

Jan 1, 2010