Search Documents

By J. O. Marsden

Part I in this series of papers considered the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical testing and initial process development for this technology. This initial work resulted in the development of a process flowsheet utilizing superfine grinding (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160° to 170ºC, followed by conventional solution extraction (SX) and electrowinning (EW) for the recovery of copper. However, this process required a significant amount of concentrated acid to be fed to the pressure leach vessel to meet the reaction requirements, representing a cost of between $0.03 and 0.05/lb copper (2006 basis) produced by the process. It was immediately recognized that the development of a process that did not require such a large acid addition would be advantageous. This paper, which is Part II in the series, describes the development of a process that incorporates medium-temperature pressure leaching and direct electrowinning (DEW) in a novel and innovative process flowsheet. Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold Inc.) refers to this as the ?MT-DEW-SX? process. Part III in this series covers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

A typical sub-level block cave mining extraction method employs an undercut level to establish a cavity in hard rock, and as such requires special support methods and products to be installed during the development phase. The undercut level development in the block cave orebody is then sacrificial, and support elements will eventually report to the crusher and perhaps conveyor belt systems for transportation to surface. The choice of support products installed in the undercut level development should take cognizance of the detrimental effect these could have on the mining system such as cutting of conveyor belts, obstructing crushers, safety aspects, and productivity. This work explores the probability and practicality of making use of new-generation support products to make the operation safer as well as enhance productivity in the development phase and during the undercut operation. This paper will investigate the use of glass reinforced plastic(GRP) rockbolts and GRP mesh instead of conventional steel bolts and mesh along with resin capsule-filled holes with the GRP bolts. Complementing this with thin spray liner (TSL) application as another means of creating a safer operating environment, as well as a productive support medium, will also be addressed. These proposed items are envisaged to reduce production downtime and improve the safety of our people. These items are all easy and light to handle, cuttable and crusher friendly, as they will break up during the crushing process.

Jan 1, 2012

By H. Razavizadeh

The recovery of copper from oxide ores containing from 2% to 4.1% acid-soluble copper from the Sarcheshmeh mine in Kerman province of Iran was investigated by agitation leaching in sulfuric acid media. Quartz, as a major constituent, and malachite, as the major copper mineral, were identified in the ore by X-ray diffraction (XRD) and microscopic studies. A series of leaching experiments on the ore was performed over a concentration range of 10 to 20 g/L and temperatures from 15° to 50°C for a maximum of 3 hours. An initial high dissolution of copper was followed by a very slow reaction. By increasing acid concentration and temperature, the dissolution rate of copper was accelerated. However, by increasing acid concentration, the acid consumption of ores was also increased. Surface morphology of solid residues at various leaching times was examined with a scanning electron microscope (SEM). All SEM micrographs of the partially reacted particles displayed a needle structure. The kinetic studies showed that the malachite dissolution rate could be modeled in two stages. About 85% of the malachite dissolution occurred in Stage 1, while the remaining 15% occurred in Stage 2. The data obtained for the leaching kinetics indicate that the dissolution for Stage 1 was a diffusion-controlled reaction with an activation energy of about 20.6 kJ/mole, and the dissolution for the Stag 2 was a chemical-controlled reaction with an activation energy of about 87.6 kJ/mole.

Jan 1, 2008

The Purification of Low-Grade Quartz Ore by Flotation and its Mechanism

Sep 13, 2010

By A. Bothma

The Impala No. 1A ventilation shaft is located approximately 15 kms north of Rustenburg and is accessed via the R510road from Rustenburg to Northam/Thabazimbi. This situation is shown on the location plan in Figure 1. The geology at the site consists of an upper layer of black turf of about 1 metre in thickness, grading into weathered norite. The depth of weathering is generally less than 5 metres. Zones of deeper weathering may occur along fracture zones associated with faults and dykes. Groundwater occurs mainly within the weathered/fractured aquifer system. The ventilation shaft is a 5.1 m diameter upcast shaft ,and forms part of a system of ventilation shafts to complement the existing infrastructure as mining progresses down the new twin decline extension of Impala 1 shaft. The principal reason for these shafts is to lessen the risk of an extended RAW and also to counter the effects of the heat build-up as the mining goes deeper, with the resultant effect that the existing cooling centre (fridge plant) becomes more remote from activities. The No. 1A shaft (upcast) is positioned approximately 1,2 km on down dip from the main shaft and the No. 1Bshaft (downcast) approximately 1,2 km further. Geological information was used from a borehole 1,2 km away on strike from the upcast shaft. The first shaft (1A) is a 5,1 m diameter hole to be fitted with two 2,2 MW fans, whilst the second shaft (1B) is 4,1 m diameter to accommodate a 7MW fridge plant.

Jan 1, 2001

IN presenting a'description of milling and treatment methods at the Waihi mine, it is advisable to first traverse a good deal of the past history of the mine, and show the various steps which have led up to present-day practice. The record of the company is one of steady, solid advancement, both in metallurgical and financial results. This is illustrated by the following figures, dating back from 1897...

Jan 1, 1912

By G. R. Robinson

Aggregate resources consist of sand and gravel, and crushed stone. They are large-tonnage, bulk-minable mineral commodities that are used in construction and industrial activities (Tepordei, 1999, 2001).Rates of aggregate production, use and mine permit approval in the mid-Atlantic region differ by population density. These rates are influenced by economic and human factors, such as demand, costs, land availability and community opposition. In some areas, the local availability of aggregate is limited. This is due to the lack of suitable local source materials for aggregate, the loss of potential high-quality aggregate resource production sites by preemptive land development and restrictive zoning (resource sterilization), and the difficulty of developing and permitting production sites for aggregate.

Jan 1, 2004

By Francisco Zenteno

Dado que la operación aurífera de Pierina representa uno de los costos operativos más competitivos del mundo, la minera Barrick Misquichilca trata de proporcionar un grato ambiente de trabajo para su personal, estimulando la creatividad y la polifuncionalidad en sus empleados. Por ello, nace el proyecto SIP2000 donde optimiza el sistema de información para el mantenimiento preventivo de la planta de procesos en la mina Pierina. El proyecto comprende el desarrollo de tres fases: La primera fase comprende la definición de los principales equipos críticos que podrían afectar a la producción, asímismo la implementación y estandarización de redes de comunicación entre equipos críticos para finalmente desarrollar interfaces HMI que supervisen variables relativas a Mantenimiento. La segunda fase, integra todos los sistemas de supervisión y control de planta con los sistemas de seguimiento “online” de Mantenimiento (fase 1), desarrollando un solo sistema de tratamiento y análisis de información de planta; y la tercera fase comprende la instalación y el desarrollo de aplicaciones basadas en tecnologías Cliente/Servidor con base SQL, que finalmente proporcionan la información y los medios para realizar consultas que optimizan el seguimiento y toma de decisiones relacionado al mantenimiento preventivo/predictivo.

Jul 17, 2000

Jan 1, 1962

This paper was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bumps in the prevention of fatalities and accidents in highly stressed, bump-prone ground conditions. Changes of failure mechanism with increasing confinement, from extensional- to shear-dominated failure, are widely observed in the rupture of intact specimens at the laboratory scale and in rock masses. In the previous analysis conducted in 2018, both unconfined and triaxial compressive tests were conducted to investigate the strength characteristics of some specimens of a Utah coal, including the spalling limits, the ratio of apparent unconfined compressive strength (AUCS) to unconfined compressive strength (UCS), the damage characteristics, and the post-yield dilatancy. These mechanical characteristics were found to be strongly anisotropic as a function of the orientation of the cleats relative to the loading direction.

Jan 7, 2020

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

By W. A. Scheuch

ORDINARILY secondary copper, unless electrolytically refined, is reclaimed directly as foundry ingots used in the manufacture of copper-rich alloy castings. This use does not require the elimination of the impurities to the degree required if the recovered metal is to be used for electrical purposes where a high electrical conductivity is of prime importance. However, as a part of the general policy of reusing its own scrap and by-products wherever possible, the Western Electric Co. at its Hawthorne Works is recovering its secondary copper as wire bars which are delivered to its own rod and wire mill and there processed into wire of high electrical conductivity. This departure from the usual recovery scheme has been accomplished through the careful classification and sorting of the material entering the furnace charges and the careful control of the subsequent melting and refining in a reverberatory furnace. Tests conducted over a period of approximately four years have shown that the quality of wire bars produced from selected secondary copper is equal to that of wire bars produced by the electrolytic refineries. The interest which has been exhibited in the process by those who have seen it has prompted the following general description. It is the authors' opinion that the recovery of secondary copper will become more and more an important factor in the copper production industry. The description is largely of the refining furnace and its operation, but it must be remembered that careful classification and sorting of the scrap materials to eliminate impurities are just as important as the furnace operation toward obtaining a satisfactory final product. Classification and sorting do not lend themselves easily to description; they must just be done. It should also be recognized at the outset that constant intelligent supervision is requisite to the success of the process because there are so many ways in which impurities can find their way into the final product.

Jan 1, 1929

"The link between ore texture and mineral liberation has previously been established at a microscopic scale. To construct ore texture models that can be used in mining applications requires this relationship to be retained at a significantly larger scale. This is initially dealt with by finding a basic set of microtextures that form the elements of the ore textures at the next larger mesoscopic scale, simulating these mesotextures at a fine scale, then changing the support of the mesotexture simulations to generate the expected mining block/stope mesotexture distributions. Thus, a mutually exclusive and exhaustive set of spatially locatable mesotextures can be used to fully characterize the metallurgical properties of in situ material.A method that generates expected distributions of mesotextures for any mining block size or shape is proposed, and includes: (1) characterizing the spatial correlation of the set of mesotextures with a single covariance function; (2) generating multiple simulations of mesotextures at a fine scale; and (3) using the simulations at a fine scale to generate the expected mining block/stope mesotexture distributions. A case study, using the George Fisher sediment-hosted base metal deposit in Queensland Queensland, Australia, is developed to demonstrate the proposed methodology as well as show the inadequacy of off-the-shelf approaches.Mining-scale texture models can be used to improve the in situ discrimination of ore from waste by exploiting the joint spatial variability of grades and textures to quantify the expected metal recovery of in situ material, then calculate local marginal cut-off grades. An artificial case study is presented to demonstrate the changes in ore/waste selection when considering ore texture models compared to constant metal recoveries."

Jan 1, 2005

By H. S. Benson

This report documents, from concept through field testing, the pan scraper Wheel Slip Monitor. The function of this device is to instantly warn the scraper operator of wheel slip and thus enable him to take immediate corrective action. Knowledgeable pan scraper people recognize that the preponderance of scraper tire damage and wear occurs during useless wheel slip when the scraper operator attempts to increase machine draft beyond what traction will allow. The resultant shortened tire life has become very expensive. The Wheel Slip Monitor reported here provides the means for relieving the scraper operator of attempting to judge wheel slip on tires he cannot see. Direct and intuitively understandable audible and flashing light warnings tell the scraper operator which wheel is slipping and also indicate the relative magnitude of the slip. Beside the Wheel Slip Monitor's patent utility as a real time operator aid, it has unique potential for application to extended term wheel slip history acquisition under field conditions. This information has never been easily available and it promises practical value in pan scraper management.

Jan 1, 1983

By Peter Cain

Longwall extraction in the Phalen Scam in the Sydney Coalfield of Nova Scotia is carried out under flooded abandoned workings in the Harbour Seam 140 m above, and at depth of up to 700 m beneath the Atlantic Ocean. Careful planning of panel and pillar dimensions is necessary to prevent inflows from the overlying workings and to prevent the development of excessive subsidence strains at the seabed. This paper briefly summarises the research undertaken over the past five years by CBDC and CBCRL into the problems associated with mining under water, and then describes the development and application of a design/planning code of practice developed jointly by CBDC, CBCRL and mine regulatory agencies. The design method employed in the Code of Practise is based on empirical data from the coalfield and parameters developed from subsidence modelling and previous water inflow experience. It includes precautionary measures to be adopted during development and mining, and monitoring procedures to be followed. It is flexible enough to allow future developments in the understanding of inflow mechanisms to be incoporated without major modifications, and represents a major step forward in reducing the potential hazards associated with coal extraction in the coalfield.

Jan 1, 1996

By Fábio Rogério do Carmo

O ar soprado é uma das principais utilidades responsáveis pelo processo de transformação do minério de ferro em gusa no Auto Forno. Para que ocorra o processo de redução o ar soprado é superaquecido nos regeneradores dos autos fornos a uma temperatura de 1.300°C. Este energético é fornecido na CSN-UPV pelos turbos sopradores da Central Termoelétrica nº 2 (CTE#2), área dos Motos Sopradores 1 e 2 e os turbos sopradores n°1 e 3 da CTE#1 que operam com a velocidade reduzida 24 horas soprando para atmosfera e consumindo vapor de 30Bar. Devido à obsolescência do sistema de ar soprado da CTE#1, alto custo de operação e risco para a segurança operacional, este trabalho apresenta o estudo do problema em questão, a metodologia utilizada para desativação do ar soprado da CTE-1 e a redução de custo.

Sep 25, 2017

By Walter G. Kutschke

Four significant soil nail wall projects in the eastern United States were recently completed with a combined area of 175,000 square feet of finished shotcrete surface. These projects required the use of innovative design and construction methods in order to address various challenges, including slide-prone back slope materials, perched water, highly erodible rock materials, curved wall alignments, very tight construction tolerances and unexpected subsurface conditions. Special focus is given to issues such as bench excavation, soil nail installation methods, shotcrete mix design, anticipated shotcrete quantities, shotcrete nozzlemen qualifications and weather conditions, in order to provide a lessons-learned database for future soil nail wall design and inspector considerations. These projects also underscore the importance of design engineer and soil nail wall contractor qualifications as well as effective communication with the owner.

Jan 1, 2007

By Hermes Vilchéz

El presente texto describe los beneficios de la apertura de los circuitos de flotación como alternativa de mejora en la performance metalúrgica de las concentradoras. El trabajo se efectuó en la empresa minera Los Quenuales, Unidad Iscaycruz (Lima), modificándose los circuitos cerrados a los abiertos y encontrándose los siguientes beneficios: el incremento del tonelaje de tratamiento sin aumentar equipos en los circuitos de flotación, la mejora en la recuperación y el grado de concentrados.

Sep 9, 2007

By George S. Rice

"""To prevent the propagation of mine explosions, the Bureau of Mines, Department of Commerce, recommends rock-dusting all coal mines, except anthracite mines, in every part, whether in damp or dry condition. It also recom¬mends that rock-dust barriers be used to sectionalize the mine as additional defense; but these should not be regarded as a substitute for generalized rock-dusting."" (Mine safety decision, No. 5, April 7, 1927.)The purposes of this circular are to present concisely the requirements for effective rock-dusting of coal mines in order to prevent propagation of mine explosions, and to point out the principal related facts on explosibility of coal dusts and mixed coal-mine dusts, as determined by extensive testing in the Experimental Mine of the Bureau of Mines. study of these principal facts on coal-dust explosibility in conjunction with the recommendations for rock-dusting, should help to make clear to mine operators and others concerned the necessity for systematic rock-dusting in all coal mines except anthracite mines, and the futility of inadequate or sporadic rock dusting.The descriptions of nearly 1000 explosion tests in the Experimental Mine are available in a forth-coming bulletin2 and in earlier publications.3For detailed specifications as to the kind of rock-dust, amount to use, where to be applied, and method of sampling and testing, the reader is referred to Bureau of Mines Serial 26064, and American Engineering Standard Committee ""Recommended American Practice for Rock-Dusting Coal Mines"" quoted in Bureau of Mines Information Circular No. 60305.Summary of Specifications for Rock-Dusting1. Mines to be rock-dustedAll coal mines, except anthracite mines, should be rock-dusted.2. Extent of rock-dustingAll open accessible parts of a coal mine should be rock-dusted, including slopes, entries, cross,-cuts, and rooms, headings and pillar workings to within at least 50 feet of the face.3 Amount of rock-dustingAfter cleaning up the coal dust as thoroughly as practicable, sufficient rock-dust should be used to have the mixture of remaining coal-dust plus the rock-dust in any zone contain 65 per cent or more of inert or noncombustible matter. First dusting may require 3 pounds to 5 pounds per linear foot of passageway.4. When to rock-dust In any zone or section (made by dividing the mine for rock-dusting purposes) when the incombustible content falls to 55 per cent, that section should be re-rock-dusted so as to bring the incombustible content well above 65 per cent."

Jun 1, 1927