Search Documents

Collecting the clay fraction of active stream sediment from a flowing stream for geochemical analysis i a difficult process. One either takes a sample of dry fine-grained sediment from the stream bank (dry weather and dry sample are uncommon in parts of New Zealand and Tasmania), or dredges up a sample of sand and mud out of the stream.The latter method produces a soggy ample bag full of mud and sand, with varying amounts of gravel, depending on the size of the stream. The water can be filtered from such a sample by means of a Buchner filter funnel, but is difficult to obtain a vacuum in the bush. This problem can be solved by using a small hand- queeze bellows such as used in priming petrol pumps on outboard petrol motors. The common laboratory hand bellows is not powerful enough.A 70 mm diameter two-piece polythene Buchner filter funnel (Fig. 1) can be used. A length of rubber tubing is fitted around the inlet valve of the hand bellows and this valve is then jammed into the pipe at the bottom of the filter funnel (the polythene pipe may be trimmed with a knife to fit over the inlet valve of the bellows). The vacuum is generated and maintained by squeezing the hand bellows.The technique of collecting a sample of the clay fraction is to dredge a sample of the fine-grained active stream sediment out of the stream with a container, such as a plastic mug. The sample is agitated to get the clay fraction into suspension and the muddy suspension is then decanted into the Buchner funnel. The desired clay fraction is obtained as a thin film on the filter paper.If the "fines" are also required, a filter of nylon bolting cloth (stretched across the mouth of a short length of 80 mm diameter polythene pipe and attached by rubber bands or a concentric polythene pipe) can be placed over the mouth of the Buchner funnel and the whole sample of stream sediment...

Jan 1, 1969

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

With the dawning of a new century came the beginning of a new era in the coal industry. Instead of the traditional practice of only buying and selling produced coal in the United States, a coal futures market was established. The New York Mercantile Exchange began trading coal futures in July 2001. But, even in this new era, many of the old is-sues that have beset the coal industry still remain, as was evident in2001. Coal production increased to are cord level during 2001, according to preliminary data from the US Energy Information Administration(EIA). Production in 2001 rose by4% to 1.01 Gt (1.12 billion st), compared with 2000 (Table 1). This barely surpassed the previous record level of 1 Gt (1.11 billion st)set in 1998. Coal consumption remained unchanged. The additional production was used to replenish the depleted stockpiles that had resulted after two years of declining coal production and increasing coal consumption.

Jan 1, 2002

By R. J. Baumgartner

Sustainability issues are from rising interest and importance for the mineral industry worldwide. In order to bring them into management processes and to improve decision processes, economic, ecological and social aspects of products, services or technologies have to be assessed. In this paper, the concept of integrated sustainability assessment is presented. Each aspect is assessed with quantitative or qualitative methods. The results of these ecological, social and economic sub-assessments are integrated by the means of Fuzzy Logic in order to regard preferences of decision maker and circumstances of decision situation. An example demonstrates the application of this new instrument.

Jan 1, 2005

Upgrading and Removing Phosphorus from Low-Grade and High Phosphorus Containing Iron Ores

Sep 13, 2010

By Jerry Gagnon, Matt Burr, Dave Evans, Timothy Ellis, Davies Kakengela, Abbas Mirza, Larry Webb, François Leclercq, Andrew Johnston

Lead-based alloys are the primary anodes used in electrowinning from sulphate-based aqueous systems. Lead anode technology has evolved over the years, migrating from pure lead and lead-antimonial alloys to the present day lead-calcium-tin alloys for copper electrowinning and lead-silver alloys for zinc electrowinning. It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new alloys and production processes, the industry still has unresolved issues related to untimely corrosion which limits anode life and may lead to higher contaminant levels in the metal being produced. Lead anodes corrode because of the difference in the chemical/electrochemical potential across the microstructural features of an anode. Given a very high purity material, we find that the grain boundary areas corrode significantly faster than the rest of the grain. The desire to minimize grain boundary corrosion by a balance of alloying element selection and microstructural design allows the grain boundary area to be engineered. However, operational issues can lead to unexpected corrosion behaviours which we will discuss moving forward. The comments in this work, though directed toward copper electrowinning, can be extended to similar phenomena in other metals electrowon from sulphate media (i.e., zinc, nickel, cobalt, manganese). The lifecycle of electrowinning anodes is dependent upon electrowinning tankhouse operating conditions and maintenance of the anodes, including cleaning and straightening. This paper will focus on the operational aspects of maximizing the utilization of lead electrowinning anodes.

Jan 1, 2015

By José Arce

El sistema AG-DAS entró en operaciones en 2015 y su aplicación tiene diversas ventajas sobre el método de polarización inducida convencional. El concepto del sistema fue el uso de múltiples receptores de dos canales, que registran la señal completa con sincronización de tiempo por GPS. La tecnología DAS (sistemas de configuración distribuida, por sus siglas en inglés) brinda mayor confiabilidad en la detección y modelamiento tridimensional de mineralización metálica con geometría compleja a profundidades de hasta más de 800 metros.

May 22, 2019

Flotation Circuit Optimisation - Towards More Sustainable Practice

Sep 13, 2010

This paper highlights the agricultural sector's primary concerns with mining in New Zealand: the information gap, land rehabilitation and compensation. It suggests how these issues can be resolved between the competing land uses in the interests of New Zealand.

Jan 1, 1981

By Seppo Haapamaki

"Since it started production in 1970, Anderson Lake Mine has experienced several radical changes in mining methods as a result of the physical characteristics of the ore zone along with the need for improved productivity. This paper examines the transition from longhole open stoping to mechanized cut-and fill then to vertical crater retreat at Anderson Lake Mine. The reasons for the need to change mining methods is analyzed taking into consideration the impact of such criteria as improved productivity and ground conditions and how these criteria affected the over-all economic viability of the mine. IntroductionAnderson Lake Mine is one of five producing copper mines in the Snow Lake area and is situated approximately 3 km southeast of the townsite of Snow Lake (Fig. I).The mine production rate at Anderson Lake is 700 tpd and all ore is trucked from the mine to the mill located approximately 2.5 km from the mine site . The mine is serviced by a three-compartment shaft sunk to a depth of 3300 ft with level spacings at 175 ft and 150 ft intervals from the 600 ft level to the 3000 ft level. .The shaft was collared in 1965 and, a year later, the hoist and compressors were installed. By 1969, a crusher system had been built and actual production began in 1970. During 1978, production was suspended for the year to allow for 430 ft of shaft deepening."

Jan 1, 1988

Coal cleat and faulting influence failure, gas release, and choice of preferred mining directions, locations, and sequences. Unfortunately soil and younger rock cover restrict direct mapping of these structures ahead of mining operations. Aerial photographs of cover contain indirect indications of concealed structures in arrays of linear photostructures. These arrays are commonly too complex for interpretation by simple visual inspection.Analytical techniques applicable to complex arrays are illustrated for a covered part of the Galilee Coal Basin, Queensland. These techniques are: optical determination of sets in arrays of photostructures; correlation of these sets with sub-surface structures; filtering of m-rays for particular sets; detection of anomalies associated with concealed structures in the density distributions of particular sets; fitting filtered arrays to trajectories; correlation of trajectories with the regional directional variations of concealed structures; contouring of ratios of sets to discriminate anomalies associated with concealed fractures and variations in the total and bed thicknesses of cover; kinematic and dynamic inference on the basis of fracture-trace angular and spatial relationships.

Jan 1, 1979

By Robert B. Fulton

The use of industrial minerals by the chemical industry as raw materials for manufacturing and in processing spans a wide assortment of minerals. This chapter aims to supplement rather than duplicate the commodity chapters. Its objective, to describe the uses of industrial minerals in the manufacture of chemicals, is attained by considering minerals used by the chemical industry in terms of the chemical element required and by giving particular emphasis to market factors. The mineral aspect, which is covered in the commodity chapters, is subordinated and attention is focused on the chemical and market aspects. Condensing this broad subject into a few pages permits treating only the most important elements derived from industrial minerals. The elements derived from petroleum, hydrogen and carbon, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potash, and nitrogen for fertilizers and titanium dioxide for pigments. After eliminating on this basis, our definition leaves six elements of major importance: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Salt brines have particular importance as raw material sources for the chemical industry as shown in Table 1 "Salt Brine Derivatives" (Anon., 1967), which charts the chemical compounds derived from four types of brines: (1) Owens Lake type brines which are sources of boron and sodium compounds; (2) Midland type brines from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake type yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak type produced mainly for lithium. Table 2 (Jones, 1973) affords an overview of the chief industrial minerals, the chemical products derived from them, and end uses of the products.

Jan 1, 1975

By N. A. Eilertsen

Mining operations were in progress at the Shawangunk mine near Summitville, Sullivan County, N. Y. as early as 1843 and again as late as 1918. Difficulty in effecting mechanical separation of sphalerite and galena was the primary reason for abandonment by various operators. The Bureau of Mines investigated this mine by diamond drilling, sampling, and performing beneficiation tests. The investigation included the construction of 1.25 miles of access road and the completion of 6,526 feet of core drilling in 24 holes. In addition, 151 samples were taken in the mine. The investigation proved an extension of ore contiguous to the old mine workings and resulted in the discovery of another ore shoot at depth. The ore occurs as fissure filling in a fault zone and contains concentrations of zinc and lead sulfides with minor dissemination of chalcopyrite in a quartz gangue. Metallurgical tests indicate that the ore can be concentrated by selective flotation.

Jan 1, 1950

By Freeman C, Dingley W

Addition of sodium nitrite-borax, sodium hydroxide, sodIUm carbonate, lime, or sodium silicate reduced wear of forged steel balls and cast iron slugs in wet grinding a complex zinc-lead-copper sulphide ore in laboratory ball mills. Maximum wear reductions were 27 per cent (forged steel balls) and 33 per cent (cast iron slugs) with sodium hydroxide and nitrite-borax additives respectively.Potential measurements of balls and slugs during grinding, and analysis of the data in terms of corrosion theory demonstrated that corrosive wear had been reduced or prevented by these additives. Actual per cent wear reductions were not equated to the rate of corrosive wear because of the undefined interdependence between abrasion and corrosion in wear processes. The investigation verifies that in laboratory ball mills corrosion is significant in the wear of grinding media and wear can be reduced by corrosion inhibition and pH adjustment.

Jan 1, 1978

By K. Y. Haramy, K. Hanna

Early identification of adverse geologic conditions and high stress concentrations during the high-speed extraction of coal using modern mechanized longwall systems is a major challenge facing the mining industry. Often, unexpected geologic anomalies that affect rock mass quality are encountered more rapidly, leaving the mine operator with insufficient time or information to deal with the changing ground conditions. The RockVision3D™ seismic tomographic system, developed by NSA Engineering, Inc., offers substantial benefits over conventional geologic/stress-detection methods and has been used successfully in coal mines worldwide. Tomographic images, produced economically and in near-real time, are easy to interpret, allowing mine operators to deal with potential hazards on a day-to-day basis.

Jan 1, 1999

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

The uphole bench extraction strategy at EKJV Management Pty Ltd?s Raleigh Mine, requires simultaneous horizontal and vertical exposure of paste filled stopes. In order to prevent excessive ore dilution, the paste fill must be of sufficient strength to prevent failure during exposure. A numerical modelling methodology has been developed to accurately simulate the initial stress distribution within paste filled stopes, together with the strain-softening loading response of paste fill material. Due to the narrow orebody width and high deformation behaviour of the host rock mass, high closure strains are likely to cause a stiff, brittle fill material to undergo crushing failure upon exposure. The stability of paste fill exposures at the Raleigh Mine was determined by conducting a series of three-dimensional numerical models that incorporate the extraction, filling and exposure sequence of paste filled stopes. Stability charts for 2.5 m and 3.5 m wide simultaneous horizontal and vertical exposures have been derived based upon the numerical modelling results. Implementation of the stability charts has proved successful in limiting the amount of ore dilution from paste fill and provides a basis to optimize paste fill cementation and stability throughout the life of the mine.

May 1, 2007

By G. Thodos, W. F. Stevens

The point-source function introduced by Horner' us a solution to the general unsteady-state equation for the flow of fluids through porous media has been utilized to calculate pressure profiles for adjacent wells as a function of time. By trial and error, the time at which the pressure waves meet to cause interference can then be calculated. For this calculation, the time of interference is arbitrarily defined as that time when both pressure waves exhibit a pressure decrease of 25 psi ar the same point within the formation. To illustrate the method, an example involving two adjacent wells producing at different rates has been worked out and is presented in detail. INTRODUCTION The initiation of production of a new well is usually accompanied by pressure drawdown measurements in order to establish the extent and characteristics of the formation. The interpretation of such pressure drawdown data is based on mathematical developments involving a single well in an infinite reservoir. If more than one well is present in a reservoir, the possibility of interaction between wells exists. Therefore, care must be taken in interpreting the pressure drawdown data. It becomes important to be able to determine when this interaction, or interference, becomes significant. This paper presents a method for the prediction of the approximate time of interference between two such adjacent wells. The basic differential equation describing the pressure distribution existing during unsteady-state flow of a slightly compressible fluid has been solved by Hor-ner.' for a constant production rate from a circular homogeneous reservoir of infinite extent. The solution utilizes the point-source function to define the pressure at various points within the formation as a function of time. The resulting expression is: q = production rate, STB/D ,;= formation volume factor, dimension-less µ = fluid viscosity, cp k = formation permeability. md H = formation thickness, ft C - fluid compressibility, psi' F = formation porosity, dimensionless R = distance from centerline of well, ft T = production time, hours Ei(—u) = Ei-function of U Eq. 1 may be used to calculate the pressure profiles generated during production from a single well in an infinite reservoir.

By Misra V. N

Davis tube tests were conducted on a Koolanooka magnetite iron ore sample, supplied by Kingstream Steel Ltd, to determine the optimum grind size, maximum iron recovery and the cleanness of the products from low intensity magnetic separation (LIMS). The ore sample contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina. XRD and microscopic examination showed that the main minerals in the ore were amphibole (42 per cent), magnetite (39 per cent), and quartz (14 per cent). Amphibole, (Mg, Ca, Fe),Si8O22.2(OH), containing 50.3 per cent SiO2, 35 per cent FeO and 11.5 per cent MgO is the main gangue mineral in the ore, and about 30 per cent of the total iron in the ore is contained in the amphibole. Heavy liquid separation tests showed that it is very difficult to separate iron from silica by gravity separation to obtain a high quality iron concentrate. Three grind sizes were initially tested, ie 45, 38 and 20 ¦m. It was found that grinding to 100 per cent -38 ¦m (P80 of 29 ¦m) appeared to be the best option for liberating the magnetite from gangue minerals. The iron recovery to the LIMS magnetic product for the 100 per cent -38 ¦m sample reached 73 per cent and the iron content was 65 per cent. Further test work suggested that the optimum grind size was a Psu of 25 ¦m.

Jan 1, 1999

By Barton J. Suchomel

Introduction Despite perennial economic turbulence, Argentina continues to push ahead with efforts to develop its fledgling hardrock mining industry. The country lacks the infrastructure and mining history of neighboring Chile, but contains vast areas of great resource potential. The eastern slope of the Andean Cordillera in west-northwest Argentina is a relatively little-explored region offering geology highly conducive to the occurrence of base and precious metals deposits. Past exploration has concentrated on locating and evaluating porphyry copper-molybdenum (Cu-Mo) type occurrences. Comparatively little attention has been given to precious metals potential. An interesting and important group of base and precious metals prospects in northwestern Argentina occurs within and adjacent to the Upper Miocene Farallon Negro volcanic complex in Catamarca province. The volcanic complex contains numerous base and precious metals vein occurrences, high gold porphyry copper prospects, and possible disseminated gold targets that have attracted relatively minor attention in the past. Various geologic aspects of the region have been reported by several workers (Llambias, 1970, 1972; Caelles et al, 1971; and Sillitoe, 1973). Regional geology The Farallon Negro volcanic complex is located within the Sierras Pampeanas morphostructural province about 200 km (125 miles) east of the main Andean Cordillera (Fig. 1). The Sierras Pampeanas is characterized by north-south-trending basin and range topography that developed during the Miocene and Pliocene. Uplifted blocks are composed mainly of lower Paleozoic metasediments and granitoid plutonic rocks unconformably overlain by Tertiary redbeds and minor carbonates. A consistent landward migration of volcanic and intrusive ac¬tivity occurred in this region of the Andes from the early Mesozoic through the mid-Tertiary. An eastward extension of magmatism during the Miocene and Pliocene resulted in the formation of the Farallon Negro volcanic center. Volcanism at Farallon Negro ini-

Jan 8, 1988