Search Documents

By Robert H. Robinson, Levent Ozdemir, Russell J. Miller

The paper summarizes an investigation into the applicability of mechanical excavation to oil shale mining; identifies available machine types that are best suited to various aspects of the mining operation; presents preliminary comments on the configuration of an "IDEAL" oil shale mining machine; and establishes the background information necessary for conceptualizing and evaluating new mining methods using mechanical excavation equipment. Conclusions are also presented as to the best currently available systems, as well as potential future systems.

Jan 1, 1983

By Dan Brown

This paper presents a case study of a cyclic lateral pile load testing program performed on two 18-in square prestressed concrete piles (PSC) in Savannah, Georgia. The load test program was developed to simulate the lateral behavior of a single pile under seismic loading conditions for the design and construction of a large LNG storage tank. The lateral load tests included cyclic loading to measure possible degradation in soil response followed by static loading to large displacements (around 6 inches at the loading point). The lateral load was applied through a reciprocating jack positioned to push and pull the piles against each other. The test piles were instrumented with multiple displacement transducers, downhole inclinometer, and strain gauges. This paper provides an interpretation of the test results regarding the pile performance and soil response to monotonic and cyclic lateral loading. A backfitted computational model of the soil resistance was developed to match the test results using the LPILE computer program. The load-deflection and deflection/moment versus depth comparisons suggest that this model appears to capture the behavior relatively well within the general range of suitability for design purposes. New design curves were developed based on the soil parameters derived from the lateral load test results.

Jan 1, 2003

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By Andreas Hucke

For the roadway design in the German hard coal mining industry, an advanced combined planning system has been applied during the past 20 years. The German mining industry is working with single entry roadways system. After first longwall passage the roadways will be stabilised with side wall building material packages. Later this roadway will be used again for the second retreating longwall. The intention of the implementation of several different design methods for the planning of the roadways is to enhance the reliability of the results. On one hand the planning system uses numerical simulation and physical modelling in addition to analytical and empirical methods. On the other hand in-situ monitoring and analysis during the roadway development will be used to verify and calibrate the numerical and physical models. Especially before the implementation of new support elements in underground, this system is suitable and reasonable because the new support elements will be tested in the physical and numerical simulation prior to cost intensive underground tests. The interaction between the numerical and physical modelling in comparison with underground monitoring and analysis during development and the later use of roadways will be shown with some examples. The first example shows a rock bolted rectangular roadway which will be mined at both sides of the roadway. Different support and roadway building material package systems are investigated under various stress conditions. The results are utilised to optimise the roadway support and the roadway side package systems. The influence of different points in time of the installation of several support elements in a combined arch and bolted roadway is shown as another example. Two different types of support systems are compared within the physical models. These models are used as a base for ongoing numerical analysis and simulation to find out the ideal point of time to assemble the different support elements. The last example handles the influence of slickensides in the roof of arch shaped roadway on their stability. Different slickenside positions and densities are investigated and classified.

Jan 1, 2006

By Constantin D. Pitis

Similarly to notions of constant capital/expenses in business or magnetization power for electric motors an energetic base load (E0) is always necessary to set up a mining process. Denominated as ?non-productive energy? or base load, (E0) is a constant component of the entire energy consumption of the process, while another component the ?productive energy? (Ep) is variable, being function of the production/throughput (M). By using these new concepts, the author creates an energetic model proposing a new method of assessing changes in mining processes (throughput) that can reveal possible energy savings (DSM component) or energy losses. Proposed mathematical model of assessing (E0) and energy savings by using ?Marginal Energy Usage Index? (MEUI) enables creation of historical benchmarks and direct on line energetic (efficiency) assessment of mining processes and/or equipments. The paper analyses the case of assessing possible energy savings that can be obtained by: ?? Improving efficiencies of various equipments (by retrofit) ? reducing E0 ?? Improving the process control or other process changes ? reducing Ep ?? Monitoring persistence of the adopted Energy Conservation Measures (ECMs). For the new plant design, the proposed method enables prediction of Customer Baseline in various mine/process configurations. The method could become part of a ?preventive action? in design process by offering a reliable tool of assessing additional financial effort (Incremental cost) when choosing various higher efficiency equipments and/or processes.

Oct 1, 2009

By G. K. Jorgenson, S. H. Chung

"IntroductionThe SABREX Blast Modelling Program was developed jointly by the companies of the ICI Explosives Group, of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.SABREX predicts the performance of blasts in terms of (I) fragment size and distribution; (2) muckpile profile and face velocity; (3) grade fracture; (4) collar breakage; (5) a rupture envelope which depicts crack penetration behind and beneath blastholes; and (6) a complete cost analysis including explosives, drilling and accessory costs. The predicted blast results are displayed as dynamic colour graphics and in tabular form.SABREX uses data on the detailed geometry of the drilled and loaded pattern, detonation characteristics of the explosives and the dynamic properties of the rock to generate blast predictions. SABREX blasting calculations take into account the effects that shock and quasi-static pressures exert on the rock around the blastholes. While physical effects occur very rapidly in rock blasting, it is possible to view and model the sequence of events as discrete sections.The program can be run on a microcomputer and is currently operated by C-I-L technical service staff in Canada for the use of drilling and blasting operators.Figure I is a diagram representing the modules of the program and associated technology that is used to complement the program.Any, or all, of the modules may be used in a particular study or blast optimization. Because the BOBCAT module of the SABREX program has been described in previous papers(7.8.9), this discussion will concentrate on the newer modules: CRACK, HEAVE, RUPTURE ENVELOPE and to a limited extent, KUZ-RAM, which present a more detailed picture of the blasting process.Each of these modules is discussed in terms of the information they offer the operator in analyzing the blast. Specific examples of recent usage in Canadian mining situations are included to illustrate the ability of the model to produce practical results that can assist in optimizing actual blasting operations or solving problems that do exist."

Jan 1, 1987

By R. N. Powell

The Pipeline ore body was discovered in March 1991. The construction of the new mine and mill did not start until early March of 1996. Upon completion of permitting and corporate project approval, the 289 million USD project was “fast tracked”. The commissioning began 11 months after start of construction and the project ended 40 million USD under the budget figure. The objective of this paper is to review and highlight the Pipeline Project history from discovery, design, lawsuits, permitting, and re-design through to current - 1998operating practices. Particular emphasis will review the process design, design mistakes, and design successes. The paper will review project history, feasibility, design concepts, operator training, construction, financial and the current operation. Additional discussion will review what design features worked and which did not work within the process plant.

Jan 1, 1999

By Ali Mortazavi

In underground mining applications, successful blasting results in less damage, which may lower support costs, lower dilution and produce a uniform fragmentation. The explosive detonation process creates a pressure front that propagates a stress wave into the surrounding rock mass at a high velocity. The stress wave can induce varying degrees of damage, depending on rock strength and physical properties, to the excavated area. This paper presents a summary of a research project that was conducted to investigate the propagation of explosive-induced stress waves in hard rock media and the mechanism of rock damage and fracturing due to shock wave propagation. The primary objective of this work was to numerically simulate the experimental study of blast-induced rock fracturing conducted within Inco Limited, Mines Research department. ITASCA?s discontinuum code UDEC (Universal Distinct Element Code), was used to simulate the results of the controlled blasting experiments. In brief, the focal point of the paper can be summarized as follows: ? Investigate the size of the stress-wave-induced fractured zone around the blasthole, ? Examine the extent and direction of the radial fractures that form outside the blasthole, and ? Explore the mechanisms that cause rock breakage.

May 1, 2002

Recent improvements are described in several techniques for ground control in underground mining. Promising methods for analysis and mitigation of rockbursts are discussed. Methods of assessing damage to underground excavations from repetitive seismic loading are reviewed. Analysis of mining-induced surface subsidence is discussed.

Jan 1, 1989

By Jamal Rostami, Ataollah Rahbar

"Uma Oya Multipurpose Development Project is under construction in Sri Lanka. This project involves 2 Rolled Concrete Core (RCC) Dams connected through a tunnel currently under construction by Drill and Blast method. The water is transferred from first diversion dam to the 2nd regulatory dam and from which, it will be transferred through a 14 km headrace tunnel to the top of a 650 m deep drop shaft that feeds the high pressure water to an underground powerhouse and turbine chamber for generation of 120 MW of electricity. The Headrace and Tailrace tunnels are being excavated by two 4.4 m diameter double shield TBMs. The headrace tunnel has already passed 5km milestone and is mined in hard rock, while the tailrace tunnel has been completed in rather weak and fractured ground. This paper will review the history of the project along with the geology of the site. The operation of TBM in headrace tunnel will be discussed in more detail, focusing on the challenges of excavating through very strong and abrasive quartzite and gneiss on this site, as well as reaches of tunnel in high inflow of water reaching 400 L/Sec. INTRODUCTION This paper aims to introduce the Uma Oya Multipurpose Development Project (UOMDP) as a hydro mechanical project in Sri Lanka, targeted generating hydro-electric power, transferring water for irrigation purposes and controlling seasonal devastating flood. This project lies in the south-eastern part of the central highland region of Sri Lanka (Figure 1). The main part of the project is located in the south-western part of the Badulla district in the province of Uva. The south-eastern end of the project site is in the central west of the Moneragala district (province of Uva). Bandarawela is the largest urban setting within the project area, located halfway between the upstream and the downstream ends of the planned hydropower plant and combination of dams, tunnels, and downstream facilities. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya. The feeder (power) tunnel Lot consists of a headrace tunnel (L=15554m), the surge shaft (L=200m) and tank on the upstream of the vertical shaft, a vertical shaft with steel lining (L=650m), an underground powerhouse and a tailrace tunnel (L=3650m)."

Jan 1, 2016

By Jacob Masliyah, Zhiang Zhou, Dharamdat Christendat, Tshitende Kasongo, Kevin Hyland, Zhenghe Xu, Ted Kizior, Douglas Cox

"A novel on-line visualization system, previously developed at Syncrude Canada Ltd., has been modified to characterize rising bubbles, particles and particle-bubble aggregates in a flotation process. With this system, the bubble size and rise velocity in a laboratory flotation cell can be determined. The technique allows the loading of solids on bubbles to be visualized, thereby providing an in-depth understanding of sub-processes of flotation. A step-by-step data processing procedure is presented. The applicability of the developed system to mineral flotation and bitumen extraction is discussed. Under batch flotation conditions in a laboratory Denver cell, three main bubble-particle attachment patterns are observed. They are: i) single particles attached to single bubbles, ii) particle aggregates loaded on single bubbles; and iii) a group of particles aggregated with a group of bubbles. The results demonstrate that the on-line visualization system is a powerful tool for understanding and diagnosing flotation processes.INTRODUCTIONAir (Gas) bubbles are an indispensable component in a flotation system. Both industrial practice and theoretical analysis indicate (Yoon, 1993; Diaz-penafiel and Dobby, 1994) that the size and population of bubbles are two important process parameters in modeling flotation. More recent investigations (Finch, et al., 1999; Gorain, et al., 1997) suggest that for a given flotation system, bubble surface area flux, defined as the air liquid interfacial area per unit time and unit cross-sectional area of flotation cell, showed a better correlation with the flotation rate constant. As a result, the bubble surface area flux is now being considered as a key parameter to account for the combined effect of bubble size and population in evaluating the performance of flotation machines and modeling flotation processes. However, the success of using bubble surface area flux in flotation process modeling largely depends on how accurate it can be determined or estimated (Finch, et al., 1999)."

Jan 1, 2000

By Poul Hansen

"In mid-I986, a world-class mining enterprise was created in British Columbia, bringing together the copper mining operations of Lornex Mining Corporation and Cominco into a new entity, Highland Valley Copper. This paper will focus on the background and rationalef or the formation of this partnership, the resulting operating changes and the productivity and cost benefits expected.IntroductionSince the deterioration of the world copper industry in 1981, the future of the Lomex and Cominco mines in the Highland Valley of British Columbia looked increasingly precarious. Despite the expansion of the Lomex mill complex in 1981 to one of the world's most cost-efficient copper and molybdenum concentrators, persistent low metal prices had made the remainder of the ore in the Lomex orebody marginally economic and had significantly foreshortened the expected life of the operation.Cominco had acquired the Bethlehem Copper assets in order to consolidate its ownership of the Valley orebody, and was feeding the Bethlehem concentrator with ore from the Valley orebody. In spite of the high grade and free-milling character of the Valley ore, profitability of the Cominco operation was severely restricted because of the limited capacity of the Bethlehem concentrator and its location high on the hillside above the orebody."

Jan 1, 1987

It is the purpose of this paper to produce some evidence on the accuracy to be expected from normal assay procedure using the usual first class equipment, and to examine the effect that many assaying inaccuracies have on reported metallurgical recoveries.Generally speaking, the evaluation of the gold content of a mineral ore sample by the fire assay method is a relatively simple process.A weighed quantity of finely ground ore is fused with suitable fiuxes including litharge and a reducing agent to give a button of lead and a quantity of slag. The shower of lead produced by the reduction of the added litharge collects the gold and silver present in the ore, concentrating the values into the lead button.The button of lead, after separation from the slag, is, on heating in an absorbent cupel in a current of air, reoxidised to litharge and absorbed into the cupel leaving a gold and silver bead in the cupel. This bead' is heated in a solution of nitric acid to dissolve the silver, leaving the gold undissolved to be dried and weighed. Knowing the original weight of the ore and the weight of the gold prill the value of the ore is easily calculated.Summarising1. Fusion Process.-Ore plus fiuxes give a slag plus lead button.2. Cupellation Process.-Lead button is re-oxidised to litharge leaving a gold and silver bead.

Jan 1, 1952

By Marc Ruest

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC?s Granger Mine, Meikle Mine, and Getchell Mine. A ?split-pipe? laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

May 1, 2002

By Jerry Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (1 l- 14 million cubic meters) of gas per day.

Jan 1, 1996

For a large scale open pit mining and concentrating operation, on a low-grade disseminated ore body, it is possible to set an approximate lower bound on economically feasible operating scales and an approximate upper bound on economically desirable scales in a relatively straight forward manner. The optimum scale ofplanned operations, with respect to the objective ofmaximisation ofthe net value ofthe orebody, will have to be arrived at by iterative planning runs, but it may be expected to lie close to this upper bound. The effects of infrastructural costs and of the addition of a risk premium to the cost of capital, to form the discount rate for planning purposes, are considered theoretically and by worked example. It is concluded that a perceived special, unsystematic, risk should not be accounted for by the use of such a risk premium as this is inducive to placing a greater amount of investment capital at risk, for no greater return-rate to investment.

Jan 1, 1986

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By Tiziana Apuani

The study refers to an area of about 70 km2, extended in the Italian Central Alps along the the San Giacomo Valley where different civil and mining works are present The regional geological setting is related to the Pennidic Nappe arrangement, characterized by the emplacement of sub-horizontal gneissic bodies resulting from the Mesoalpine isoclinalic folding of crystalline basements, emplaced throw East, and separated by matasedimentary cover units. The investigated geological rocks, belong to the ?Tambò?Unit, overlapped by its meta-sedimentary cover and by the ?Suretta? Unit. The tectonic contact gently dips to the E?NE. The valley, furrowed by the Liro Torrent, follows a N?S striking tectonic lineament, almost parallel to the nappe contact. A number of more then 70 sites, distributed in the studied area, were chosen and detailed structural and geomechanical field surveys were performed to characterize the rock masses, its intact rock and discontinuities. The procedure identifies the number of joint sets, their representative orientation, the set spacing, the type of movement, the amount of dilatation, the degree of alteration, the roughness coefficient, the presence and nature of infill. Rock mass quality indexes, such as the Rock Mass Rating (Bieniawski, 1989) or the Geological Strength Index (Hoek et al. 2002) have been evaluated in each surveyed site. The work is a contribute in assessing how the geometrical and geomechanical properties of the rock masses can be regarded as regionalized variables. The spatial distribution of these properties is a function of the geological and structural phenomena at which the rock masses have been subjected. The presented geostatistical analysis regards the spatial variation of the orientation of the most representative joint set.

May 1, 2009

By D. K. Bose, R. H. Rakhasia, V. D. Shah, J. C. Sehra

A series of experiments was conducted to determine the effects of roasting temperature, soaking period and quantity of soda ash added. At a laboratory scale, under optimum conditions of roasting at 873 K for 2 700 s with soda ash 10 wt% in excess of stoichiometric, molybdenum recovery was 99%. The investigations indicate the technical feasibility of producing high-purity MoO3 by combining the roasting process with carbon adsorption/desorption. The process uses low-cost chemicals, can be scaled up readily and is free of the SO2 pollution generated by conventional roasting, as the sulphur content of the concentrate is converted to sodium sulphate

Jun 18, 1905