Search Documents

By Don Rose

INTRODUCTION A number of tunnels supported and permanently lined by steel-fiber-reinforced shotcrete (SFRS) have been built in North America in the 1980s. The material is more economical than, and technically equal or superior to, conventional shotcrete using wire mesh. The design and construction of SFRS-lined tunnels is straightforward, and only a few new design principles, laboratory tests or construction equipment modifications appear necessary in order to use this material. Modern tunnel Contractors may use cyclic drill-and-blast methods on some tunnels, with intermittent shotcreting as part of an orderly cycle. The Dry Mix method is most suitable for cyclic, intermittent, relatively small-scale shotcreting. However, modern Contractors excavating tunnels continuously using large long Tunnel Boring Machines (TBMs) or Roadheaders may prefer Wet Mix shotcreting on a mass production basis. In either case, the use of steel-fiber-rein¬forced shotcrete (SFRS) promotes the rapid and economical excavation of tunnels. The addition of microsilica will improve SFRS properties and reduce rebound, and is expected to become standard practice with SFRS in North America, as it now is in Scandinavia. HISTORICAL REVIEW Steel-fiber-reinforced shotcrete (SFRS) at the present time (1985) is essentially conventional shotcrete with straight or deformed steel fibers added, and in general SFRS for tunnel linings encounters the same problems that conventional shotcrete does. Shotcrete history is well known. The use of sprayed plaster on wire frames for mounting animal skins by Carl Akeley of the Smithsonian

Jan 1, 1985

By Eder Salazar

Como parte del desarrollo de sus operaciones de mina de cobre subterránea, la Sociedad Minera El Brocal S.A., desarrolló el método de minado tajeo por subniveles con pilares recorridas con el fin de incrementar su producción actual. En ese sentido, el presente texto señala la implementación de un método de minado conforme a las características geomecánicas del macizo rocoso del yacimiento.

Sep 12, 2011

By A. Uiga

The U.S. Bureau of Mines funded a project which addressed objectives concerning irrigation of native plants and inoculation of native plants with vesicular-arbuscular mycorrhizal (VAM) fungi. The specific irrigation objectives were 1) to demonstrate the performance capabilities of solid-set irrigation for reclaimed mineland conditions, and 2) to demonstrate and evaluate three irrigation concepts under two separate water supply conditions. The VAM inoculations were to assess irrigation benefits in establishing VAM relationships for transplanted native species. Following the seasonal demonstration (May to September 1983) at 3 separate mine sites, conclusions were made that apply to the 6 state Western mining industry. The demonstration sites were located in Montana, Wyoming, and New Mexico. Positive conclusions were reached for 1) the use of soil moisture sampling with or without irrigation, and 2) the selection of solid-set sprinklers as the irrigation method. The conclusions about the irrigation concepts and strategy were mixed, due to the short-term (1 season) nature of the project. No conclusions could be reached for the VAM inoculations because the study time was too short.

Jan 1, 1984

By A. McKenzie

During the late 1990s Anglo American PLC was evaluating the Gamsberg zinc deposit in the Northern Cape Province. As the primary South African metallurgical technology provider, Mintek became involved in the evaluation of a pyrometallurgical process for the recovery of zinc from the Gamsberg deposit. eloping DC arc furnace technology for the metallurgical industry. This includes the patented Enviroplas® process for the treatment of zinc bearing waste materials. As a consequence Mintek has developed extensive expertise in the pyrometallurgical processing of zinc bearing materials. However, Mintek?s technologies stopped with the production of Prime Western Grade (PWG) zinc. Early on in the evaluation of the Gamsberg project, it became evident that the refining of PWG zinc would play an important part in the economic viability of the project. At the time the only pyrometallurgical technology available for the refining of PWG zinc to Special High Grade (SHG) zinc was the New Jersey process. This process represents 50-year-old technology and has not undergone significant refinement since the technology was developed. In order to provide a complete pyrometallurgical flow sheet for possible implementation at Gamsberg, Mintek assessed the New Jersey process with a view to either improving the technology or developing a new technology appropriate to the 21 century. In 1998 Mintek convened a consortium consisting of Mintek, the University of Cape Town, Eskom Enterprises, Bateman Metals and Anglo American PLC. The consortium successfully applied to the Innovation Fund for funding to develop a new process for the pyrometallurgical refining of PWG zinc to SHG zinc. The main aims of the project were to develop a new technology for pyrometallurgical zinc refining that conformed to the following: ?Decrease the production cost of SHG zinc metal to stimulate the development of the Gamsberg deposit. ?Be compatible with the current Enviroplas® process, preferably as an add-on to that process. ?Should use electrical energy to benefit from local price tariffs. The project commenced at the beginning of 2000 and consisted of three phases: ?an initial technology search and assessment of the fundamental aspects of zinc distillation. ?the design of a pilot plant for zinc refining. ?the manufacture, commissioning and operation of the pilot plant. A new technology based on a DC arc boiler feeding a packed distillation column was developed and during 2003 the project culminated in the successful operation of a 200 kg/h pilot plant. Ultimately, all of the aims of the project were met and the main outcome is that an advanced process for the pyrometallurgical refining of zinc (the Zincref process) has been developed. The main innovation of the technology was the switch from an energy transfer limited process to a mass transfer limited process (for which a patent has been registered).

Jan 1, 2004

By M. A. Meyer

Underground mining accidents in the USA in recent times have prompted the Mine Safety and Health Administration (MSHA) to review emergency and tracking systems for underground mines. Several communication and tracking systems are available on the market and various systems have been installed in mines around the world. In addition, MSHA?s standard on Diesel Particulate Matter (DPM) requires mines to comply with the final PEL of 160µg/m3 by May 20, 2008. Barrick Goldstrike Mines Inc., Underground Division, has been in operation since 1995 and an extensive control and monitoring network, and a leaky feeder voice network is in place. Enhancements to the communication and control system are currently being implemented to include a PED emergency notification system, wireless LAN with tracking of personnel and equipment in the mine, and a ventilation control system that will use the tracking information and ventilation data to automate much of the mine ventilation system. Expected benefits from such a system would be enhanced communication with miners, emergency notification, location of miners and equipment, energy savings, improved ventilation control, and improved atmospheric conditions in the mine including reduction of diesel particulate matter (DPM).

Jan 1, 2009

By Michael Allen, Paul Worsey

In underground blasting, the pull of the initial cut is the limiting factor for the success of the rest of the round. By improving the pull of the first cut, a critical step is made towards improving the entire round. This project attempted to optimize a burn cut’s effective pull by varying the depths of the relief holes in the burn. The effect of varying the depths of the relief holes was investigated, including depths longer than that of the cut’s charged holes. The overall objective was to consistently achieve greater pull than in a standard burn, using an identical amount of explosives. Increased pull results in savings of both time and cost in underground heading advance.

Jan 1, 2015

By Martin Nevens

"In 1998, the Iron Ore Company of Canada initiated an aggressive program to improve the performance of its Carol Lake Concentrator located in Labrador City, Newfoundland. This program was termed the Concentrator Upgrade Program. The Concentrator Upgrade Program was a group of initiatives developed with the common goal of improving the overall process and operations of the IOCC Carol Lake Concentrator. The main goal of the program was to increase the annual production capacity of the concentrator from 18.0 million tomes to 21.6 million tomes. This gain in capacity was to be done mainly through improvements in process iron recovery. The target iron recovery value was 80+% versus a historical value of 70%. This improvement in iron recovery would translate to a natural weight recovery improvement from 44% to 50%.The Concentrator Upgrade Program provided the first opportunity in 30 years to make fimdamental changes to the concentrator flowsheet. To accomplish this, several pilot plants were built to evaluate new circuits. AAer 2 years, a new flowsheet was selected for the primary gravity separation circuit and the magnetite circuit. The centrepiece of the new flowsheet was the introduction of Hindered Settling Separators to the metallurgical process.The Concentrator Upgrade Program has since proceeded into detailed engineering and, as of February 2001, construction. The first one of IOCC’s 3 primary AG Mills (Mill 11) has been converted to the new flowsheet at the time of writing and is in the throes of commissioning. This paper will review the flowsheet development program in the pilot plant for the gravity separation circuit and examine the overall benefits to the operation of the IOCC Carol Lake Concentrator."

Jan 1, 2002

The mining industry has recognised for some time the importance of supporting programs which serve to educate the Australian public about the socio-economic benefits of mineral resource development. More recently, industry leaders have realised that the future development of the industry will depend on attracting sufficient young people to commit to a career in the industry. Apart from lending support to the traditional education institutions in Australia, the industry now has the opportunity to participate in the development of education programs in museums. Whilst historic, mining-related theme parks such as Sovereign Hill and Coal Creek in Victoria serve very effectively the objective of relating past mining activities to the socio-economic development of Australia, there still exists the need to provide a facility which, under the same roof, excites interest in geology, mining, mineral processing and the role of minerals and energy in modern society. The redeveloped Geological and Mining Museum (the "Mining Museum"), which is located in The Rocks area of Sydney, meets this objective. With the central themes of formation and transformation this new Museum, which aims to be the best of its type in the world, will use modern museum exhibit techniques and the resources of the Minerals and Energy Information Centre to educate the community including teachers and school children. In the best tradition of museums, outstanding mineral and other collections will complement a comprehensive range of interactive, high technology exhibits which will include a number of exploratory "hands on" facilities. Australian companies are joining with Government to fund this exciting new museum. There is still a need for industry professionals to realise that a modern "mining" museum is no longer just a repository for objects of mining heritage but is also an important centre which serves as an important educational and public relations interface. The Education Section of the new "Mining Museum", which is linked closely with the new Minerals and Energy Information Centre, will be working closely with appropriate mining-related Tertiary institutions to develop specific career programs aimed at secondary students who wish to pursue a career in the mineral resource industries.

Jan 1, 1989

By S. O. Bada

Coal samples taken from the No. 2 Seam and No. 4 Seam in a South African colliery were tested in a rotary triboelectrostatic separator. The two-stage triboelectrostatic separation results using the -177 µm size fraction reduced No. 2 Seam coal containing about 30.4 per cent ash to a clean product of 8.9 per cent and 13.1 per cent ash with combustible recoveries of 9.6 per cent and 30.7 per cent respectively. The same separation approach on No. 4 seam feed coal, which contained 36 per cent ash, produced a clean coal product with 10.8 per cent ash at a combustible recovery of 6.0 per cent. Petrographic tests show a significant improvement in the vitrinite content and a reduction in visible minerals encountered when using the triboelectrostatic separator, with about 53 per cent vitrinite reporting to the clean fraction for No. 2 Seam compared to the feed content of 21 per cent, and a 54 per cent vitrinite in the clean No. 4 Seam from a feed content of 21 per cent. Significant sulphur reductions were also observed after separation in both coal samples, with a better separation in the second-stage coal products.

Jan 1, 2012

By Raphaël Mermillod-Blondin, Claude Bazin

"Sampling is an important step for ore body evaluation and daily plant material balances. The Gy’s equation is regularly used to assess the size of the samples to be collected and to estimate the reproducibility of the collected samples. The equation works well for iron and base metal ores but seems to produce pessimistic estimates of the gold content reproducibility for gold ores. A model is proposed to simulate the division of samples using a standard splitter and discrepancies are observed between the Gy’s equation predictions and simulated samples reproducibility for crushed gold ore. Results of the simulation show that sampling a pile of ore crushed to -2 mm should lead to more reproducible gold content than it is observed in practice and predicted by the Gy’s equation.INTRODUCTION With current gold prices above $1400 per troy ounce operators seek for new economical ore bodies. The metallurgical evaluation of an ore body is one of the numerous steps required to justify the investment for the development of a gold mine. Metallurgical testing requires to sample the ore body and to prepare the ore sample for the grinding and separation tests. The preparation implies crushing the ore usually to less than 2mm and its division into batches of a given weight for subsequent processing. For gold ore testing a batch of crushed ore is ground in a laboratory mill and leached using cyanide. Gold recovered in the solution is used as an indicator of the ore processing amenability. One difficulty associated with ore testing is due to the reproducibility of gold content measurements of the feed sample. According to the Gy’s equation (Gy, 1979; Morisson, 2009) the division of a 20 kg batch of -2 mm ore containing 5 g/t of gold into batches of 1 kg may lead to batches containing 5 ± 5 g/t of gold. For this reason the gold content of a feed sample is usually back calculated from the assays of the solution and solids residues of the leaching process. However, these two assays may contain measurement errors that can propagate through the calculation of the gold recovery. The use of the feed assays as a redundant information could add robustness in the evaluation of ore amenability to processing. This paper discusses the problem of sampling reproducibility for a gold ore. The analysis is carried out with reference to the Gy’s equation for the sampling of particular materials."

Jan 1, 2012

By I. A. Costa, Y. Fouquet, F. Barriga

"Lucky Strike and Menez Gwen are two hydrothermally active sites located along the border of the Azorean plateau, southwest of the Azores islands where the alteration processes affecting basaltic rocks are prominent (Costa et al., 2003). Here we report on a slabby brecciated rock, abundant at both Lucky Strike and Menez Gwen, composed mainly of basaltic fragments cemented by hydrothermal precipitates from warm fluid circulation system. Research reveals that hydrothermal alteration takes place mainly by replacement processes, in which silicification is dominant (Costa et al., 1997 and Costa, 2014).Petrographic observations, including scanning electron microscopy (SEM), microprobe analysis, and mass balance studies made on basaltic fragments within the breccia show that silicification is one of the main processes resulting from hydrothermal fluid circulation. This alteration process leads to complete replacement by silica, in extreme cases, forming an impermeable cap that may contribute to the formation of sub-seafloor sulphide deposits, including examples in the geological past."

Sep 1, 2014

By J. A. Meech, G. R. Baiden

"A dynamic simulation of a mine-mill complex has been conducted using networked microcomputers (IBM PC/AT and IBM PC/XT). These models allow simultaneous operation of an open pit using shovels and trucks, a primary crusher, and a secondary crushing plant. Each process transmits information via the network, linking all operations together. The effects of blasting, ore quality, equipment utilization and configuration on productivity can be studied either interactively or from a report listing at the end of each shift. Programs are menu driven leading the user through the decisions required in day to day operations. The mine-mill simulator is currently being used as a teaching tool at Queen's University to provide senior mining and mineral processing engineering students with an experience and appreciation for the operating problems across the mine-mill interface. The need for coordination and close communication between the mine and mill can be aptly demonstrated using these models. The simulator could be used to contribute to the training of operating personnel in a real mining operation. INTRODUCTIONThis paper describes a computer simulator that is capable of showing the interactions and operating strategies between a mine and a secondary crushing plant. The simulator uses two models developed at Queen's University; one for open pit mining and the second for secondary crushing. PITSIM is a dynamic shovel/truck haulage model origin2lly developed by P.D.D. Chick (1) and K.G. Fytas (2) to solve shovel/truck scheduling problems. CRUSHSOFT is a dynamic secondary crushing plant model developed by R.J. Tucker (3) and C.A. Harris (4) to study alternative operating and control strategies in a crushing plant."

Jan 1, 1987

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009

By Osetzky D, Hesp W. R

The treatment of a hydrobiotite containing 0·64 per cent copper with various soluHons showed that a high percentage (up to 90 per cent) of the copper can be extracted under mild conditions (1 M BCI, 85°C) or withsaline solutions (20 per cent by weight NaCI or NH4F, 400°C). The latter results suggest that the copper is incorporated in the interstratified vermiculite of a vermicuHte-biotite mica and the solutions (NaCl and NH4F) which reacted with the vermiculite without attacking the biotite gave the highest extraction yields.In general, extraction yields with saline solutions increased with the temperature (between 100 and 400°C) and duration (3 or 6 days) of the treatment but were not appreciably affected by the initial pH of solutions.The results of RCI treatment especially may have a bearing on the hydrometallurgical treatment of refractory copper ores where copper is tied to gangue silicates.

Jan 1, 1977

In order to maintain a production rate of 6,000 tonnes per day from underground at the Williams Operating Corporation, two independent mining areas were required which created a long narrow sill pillar between them. During initial mining of the sill pillar there were a number of significant ground falls [LeBlanc and Murdoch, 2000] and in March 1999, with no active mining ongoing in the sill pillar area, a rockburst of magnitude 3.0 Nuttli occurred. Extensive ground support was designed and installed to withstand events of similar magnitude [Bawden and Jones, 2002]. A mine wide microseismic system was installed to monitor mine induced seismic behaviour over the entire mine. The area most directly affected by the 1999 rockburst was rehabilitated using a highly ductile support design. Along with microseismic instrumentation, the areas were instrumented using conventional SMART Cables and SMART MPBX?s. Subsequent to this, the area was impacted by a large number of high magnitude seismic events [magnitudes between 1.7 and 3.5 Nuttli]. The ground support performed very well during these events, providing confidence in the mine?s ability to control the ground under severe rockburst conditions. Analyses of microseismic and conventional instrumentation, combined with numerical analyses of sequence alternatives, were used to develop an optimal mining strategy for the sill pillar area. The selected strategy involved utilization of instrumentation data and calibrated model results to analyze yield zones in the sill. The analyzed ?yielded? zones were assessed to be low seismic risk. Initial mining in the sill was then concentrated in these low risk areas, with the objective of further concentrating stress into the remaining seismically active area, in order to induce ultimate failure of the sill. Continuing large magnitude seismicity and resulting damage in the remaining ?high seismic risk? area, led to abandoning a second portion of the footwall access and the strategic decision to extract a stope near the centre of this zone in order to force final failure of the sill pillar. During execution of this plan two large magnitude seismic events occurred resulting in destressing and final failure of the remaining sill pillar. The paper provides a detailed description of this ?strategic mine sequence driven self-destressing process? and the implications to final extraction planning in this area of the mine.

Apr 1, 2005

By James A. Brierley

Wastewater from uranium mines in the Ambrosia Lake district near. Grants, New Mexico, U.S.A., contains uranium, selenium, radium, and molybdenum. The Kerr-McGee Corporation has a novel treatment process for waters from two mines, sections 35 and 36, to reduce the concentrations of the trace contaminants. Particulates are settled by ponding, and the waters are passed through an ion exchange resin to remove uranium; barium chloride is added to precipitate sulfate and radium from the mine waters. The mine waters are subsequently passed through three consecutive algae ponds prior to discharge. Water, sediment and biological samples were collected over a 4-year period and analyzed to assess the role of biological agents in removal of inorganic trace contaminants from the mine waters.

Jan 1, 1981

By D. Norval

Keywords: Pyrometallurgy, slag, metal, entrained, granulation, ferromanganese Water granulation of certain slags with high metal entrainment has customarily not been practised, not only due to the belief that such processes are too dangerous and unproven in the pyrometallurgical industry, but also that it might not be economically viable or environmentally acceptable. General slag granulation, on the other hand, is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. Thus, purpose-designed granulation and solidification processes are discussed, taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte, or alloy responds in similar fashion to a granulation practice. This paper addresses three issues, namely: ? Water-granulation of BOF steel slag, without processing it to render it environmentally safe, physically and chemically acceptable for use by the construction industry, and the process economical ? Processing air-cooled BOF steel slag to change its physical and chemical properties to be acceptable for various uses and extracting metallic and bound iron ? Processing air-cooled or molten manganese slag to lower its manganese content to a level that is acceptable from an environmental and health point of view, and extracting FeMn-alloy of acceptable composition. The latter process culminated in a patented process to extract FeMn from air-cooled and molten manganese slag, and, at the same time, produce a hydraulic (cementitious) slag, thus transforming a possible hazardous by-product into virtually 100% saleable products.

Jan 1, 2011

By Felix E. Mutschler

Alkaline rock-related precious metal deposits include: • orthomagmatic platinum group elements (PGE) ± gold (Au); • porphyry copper-silver-gold (Cu-Ag-Au, ±PGE); • epithermal Au-only, and Au-Ag-base metals; • submarine exhalative Kuroko-, Cyprus-, seamount- and Yellowjacket-type deposits; and • enigmatic deposits akin to Olympic Dam. Coeval epithermal deposits related to porphyry deposits suggest the two types represent separate immiscible fluids evolved in oxidized, CO2-rich alkaline magma chambers. Alkaline rock provinces develop above mantle hot-spots, but crustal structures control the final distribution of magmas and ore fluids. Prospecting guides for alkaline rock-related precious metal deposits include the presence of evolved alkaline rocks, pervasive K-metasomatic, redox and carbonatic alteration and low level Au (±Te, etc.) anomalies. Although alkaline igneous rocks crop out in less than 1 % of the area of the North American Cordillera and craton, alkaline rock-related ore deposits have produced nearly 13% of the total United States and Canadian lode gold production. Large (31-t or 1 million-oz) deposits are common (Fig. 1), and additional deposits and reserves are being discovered. New genetic models are evolving, making alkaline rock-related precious metal prospects attractive exploration targets.

Jan 1, 1991

By H. Warren Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomic. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

May 1, 2002