Search Documents

By Masahiro Yoshimura, Sergiy Korablov

"Hydi-othermal corrosion ofTiN, TlAlN and CrN PVD films (3 µm thick) deposited on SUS-304 substrate was studied in 100MPa water in 20-950°C temperature range up , to 750h. The beginning temperature of their reaction was determined as 200°c for TiN and TiAlN and 500°C for CrN films, which are quite low in comparison with that of air oxidation of those powders. Very thin oxide scales. of TinO; n-I homologous series phases were formed above 300°C. TiO2 anatare. is observed for TIN and TiAlN films at 400°C. The· feature of hydrothermal corrosion of CrN films seems to be CrNxOy phase formation.Distinguishable weight changes were observed at higher temperature than 700°C for TiN, 750°C for· TiAlN and 800°C for CrN respectively. Hydrothermal corrosion kinetics .was constructed to calculate the activation energy of hydrothermal corrosions. On the base of obtained data, hydrothermal corrosion resistance was as follows: TiN – TiAlN - CrN. Facetted oxide crystals were formed at higher temperature than 500°C for TiN, TiAlN and 850°C forCrN.IntroductionThe metallic nitride (TiN; TiAlN, CrN) PVD films have high hardness, strength and wear resistance. Therefore these films are widely used in industry for wear resistij.nce application such as cutting tools and die molds. Their performances depend on not only the mechanical properties but also corrosion resistance of coated films. High temperature oxidation of metalliq nitride and nitride films was well studied [1-5]. However there are no reliable data concerning the .corrosion resistance of coated nitride materials. In high-temperature and high-pressure water. There are a few reports on hydrothermal corrosion of nitride films [6,7]. The increase of corrosion resistance of CVD films was observed in following succession TiC - TiCNO - TiCN - TiN at 300-680°C temperature interval and I 00 MPa pressure water according to data of the first report. Kawana et al. [7] have reported about excellent corrosion resistance of CrN films under 290°C and 8, 6 MPa water during I 000 h in the circulating type experimental loop. The films thickness was about 7-10 µm in both cases. However it remains unclear the chemical state of the surface species and especially in-depth distribution, oxide scale thickness and its growth, and defects formation in the oxide film."

Jan 1, 2000

By William A. Hockings

Methods for the measurement of liberation of finely ground iron ores are described. The general method consists of separating a sample of the ground ore into a number of size fractions, followed by measuring the liberation of each fraction. The size separation has been done using electro-formed screens of 20-, 10-and 5-micrometer apertures, and also by air elutriation. Liberation (i.e., the distribution of compositions of individual particles) has been measured by optical microscopy. A computer pro-gram was used to adjust the raw count data so that it agrees with the chemical analyses of the size fractions. Various ways of presenting the results are given, and Some applications of the results to flotation processing are discussed.

Jan 1, 1981

By Maurizio Marezio Bertini

Successful treatment of contaminated sediments was achieved by sparging either 0.5 M NaOH solutions or distilled water with an SO2/O2 gas mixture. Metals such as Cu, Pb, Cr and Cd were successfully removed in a relatively short time. The effect of temperature and pH was investigated. Higher temperatures produced faster and higher recoveries with Pb and Cr more affected to temperature increase than Cu and Cd. The removal of copper, up to 50% percent, was achieved in alkaline solutions through the formation of copper sulfite complexes. The complete removal of metals such as Cu, Pb, Cr and Cd required that part of the treatment be carried out in acidic solutions. A preliminary cost analysis was carried out.

Jan 1, 2003

By Junji Shibata

The waste acid mixture whose main component is phosphoric acid, is discharged from the etching process in the liquid crystal production industry. In order to separate impurity acids from the phosphoric acid, trioctyl phosphate (TOP) is used as an extractant. TOP can extract acetic and nitric acids selectivity. The extraction and stripping operations are carried out for the acid mixture by beaker-scale experiments and countercurrent multistage operations with mixer-settler equipment. TOP selectively extracts the acetic and nitric acids in the acid mixture. From the results of the McCabe-Thiele analysis obtained by beaker-scale tests, the extraction for acetic and nitric acids are approximately 100%, respectively, by 6-stage extraction with a phase ratio (A/O) of 0.4. On the other hand, almost all of acetic and nitric acids are stripped with water from the organic phase by 4-stage stripping with a phase ratio (A/O) of 1.0. About 95% of acetic and 98% of nitric acids can be removed from the acid mixture without extracting phosphoric acid in case of the mixer-settler equipment operation. There are several steps such as slicing, lapping, chemical etching and mechanical polishing in the silicon wafer production process. The chemical etching step is necessary to remove any damaged layer caused in the slicing and lapping steps. The typical etching liquor is the acid mixture comprising nitric acid, acetic acid and hydrofluoric acid. The waste acid is treated by a neutralization method with a high alkali cost and balky solid residue. A solvent extraction method is applicable to separate and recover each acid. Acetic acid is first separated from the waste liquor using 2-ethlyhexyl alcohols as an extractant. Then, nitric acid is recovered using TBP (Tri-butyl phosphate). Finally hydrofluoric acid is separated with TBP solvent extraction. The expected recovered acids in this process are 2mol/L acetic acid, 6mol/L nitric acid and 6mol/L hydrofluoric acid. The yields of this process are almost 100% for acetic acid and nitric acid. On the other hand, it is important to recover and reuse the metal values contained in various industrial wastes from a viewpoint of environmental preservation. Most industrial products are made through processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane separation, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. Some examples of the application of solvent extraction to the treatment of wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse solution, etching solution and pickling solution are introduced.

Jan 1, 2003

By Huanmei Yuan, Yuanyuan Wang, Hao Bai

Composite phase change materials are widely used in energy-saving and energy efficient process. Nano-encapsulated phase change materials are especially significant for making advanced working fluid applicable to waste heat recovery or storage. In this study, silica-coated stearic acid (SA) Nano composite phase change materials were prepared from tetraethyl orthosilicate (TEOS) and stearic acid (SA) via sol-gel process. The materials were investigated by Field emission scanning electron microscopy (FE-SEM), Transmission electron microscope (TEM), Fourier transform infrared spectroscopy(FT-IR) and Differential scanning calorimeter (DSC).The FE-SEM and TEM results show that monodisperse microspheres with stable core– shell structure were formed and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reaction between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity.

Jan 1, 2016

By Geza Kisvarsanyi

Ore deposits composed of enargite, tennantite, gold, and pyrite have been mined in volcanic rocks of Oligocene age (35 m.y.) at Recsk, Hungary. Vertical and horizontal zoning of the alunitic-argillic alteration and of the ore minerals led to the concept of an intrusive heat source at depth. Subse-quent drilling disclosed a series of ore deposits in a zoned pattern in and around a stock, separated by a barren gap of 1000 meters from the shallow ore. The ore system is in a intracaldera horst-graben structure, formed by collapse and intrusion in a microplate subduction. volcanic-arc tectonic environment.

Jan 1, 1987

Rotary kiln incinerators are widely used in the incineration of various types of hazardous wastes. However, the complex transport processes within the incinerator are not well understood. Due to large variations in waste types and difficulties in feed characterization, the incineration process meets great challenges in a smooth operation, and expects uncertainties in the process chemistry and emission control. In order to get better understanding of the incineration process, process simulation was made on the kiln behavior by using Computational Fluid-dynamics (CFD) to characterize gas flow, temperature distribution and waste combustion in the incinerator. Temperature measurement was conducted in an operating incinerator to validate the CFD model. This paper addresses the environmental issues related to the hazardous incineration process, and reports the recent simulation results on gas flow and mixing, combustion heat transfer, and potentials to reduce emissions.

Jan 1, 2002

By Leandro Voisin

A new pyrometallurgical treatment alternative is proposed for cleaning complex copper matte with high content of impurities in the copper smelting process, thus, in a suitable furnace, a given amount of pig iron will be added to the liquid complex matte with a matte grade between 65 and 75 % Cu under reducing condition and will produce three liquid phases of matte, copper-rich alloy and iron-rich alloy. Hence, in this study, firstly, a mass balance calculation was made on the basis of the reported data for the distribution ratios of the components among the three phases to define the optimum condition where most of the arsenic can be fixed in the less valuable liquid iron-rich alloy. By taking advantage of the high concentration of arsenic in the iron-rich alloy, the small volume alloy may be disposed in a yard, while the precious elements may be recovered effectively in the liquid copper-rich alloy and/or in the liquid matte. Secondly, laboratory-scale experiments were conducted to apply the proposed process to the matte produced from the slag-cleaning electrical furnace and the Teniente Converter of the Codelco-Norte smelter. The obtained results indicate that the proposed process for cleaning complex matte is promising.

Jan 1, 2006

By O. Nakai

In the copper electrorefining process, the quality of the starting sheet is one of the basic factors for producing high quality copper cathodes. A highly automated and advanced facility for the production of copper starting sheets was constructed at the Toyo Copper Refinery in 1992, bringing various improvements into an automatic stripping system using stainless steel mother blanks. In 1998, the refinery expanded the tankhouse by another 128 commercial cells, and introduced 64 polymer concrete cells in a first stage conversion. As a result, the Toyo Copper Refinery now has the capacity to produce 103,200 t/y of cathode copper. Construction has led to great improvements in the materials handling facilities and computer associated short-circuit detection technology. This report summarizes the improvements made in the quality of the cathodes and in plant productivity.

Jan 1, 1999

By Robert D. Pehlke

"The evolution of oxygen steelmaking is reviewed and new operating processes are described. The developments which could impact this technology are summarized. Staged and continuous steelmaking are considered in the light of new technologies. The future opportunities for oxygen steelmaking processes are overviewed. IntroductionThe use of oxygen in steelmaking was originally brought on the scene by the development of pneumatic steelmaking. Sir Henry Bessemer in England originally conceptualized the use of gaseous oxygen in steelmaking, and then he and William Kelly in Eddyville, Kentucky independently developed the original pneumatic process which involved blowing air through a bath of molten pig iron to oxidize the carbon and silicon and produce steel. This process and many following processes, including those which would use pure oxygen gas, have been proposed.Beginning with the first commercial oxygen steelmaking vessels at Linz, Austria in 1952, the world steelmaking industry has adopted this style of processing. In general, the process has involved the use of steel scrap in amounts from 20 to 35% of the metallic charge with molten pig iron produced in blast furnaces making up the remainder. The impurities in the charge are oxidized through the use of oxygen gas injected into the steelmaking vessel.However, currently being adopted into commerical practice and on the horizon are a number of advances in this process which include the use of iron ores as a source of iron and oxygen, the use of an all scrap charge, incorporation of pre-reduced iron, the use of auxillary fuels to change the balance of cold and liquid iron-base charge materials and numerous refining techniques."

Jan 1, 1988

By C. Lupi

Zinc impure solutions as spent electrolytes, leach liquors coming from aqueous treatment of both minerals and solid waste, need to be purified before undergoing the treatment to obtain the final product. Solvent extraction is one of the most selective operations particularly when many metallic ions are present in solution. Zinc pure solutions are frequently obtained using DZEHPA as extractant. In this work an investigation on zinc extraction effectiveness of naftenic acid was carried out. After determining the best diluent and the optimal extractant concentration, the partition coefficient was determined as a function of temperature, equilibrium pH and zinc concentration. Finally same batch tests to determine the equilibrium curves at room temperature on exhausted electrolyte coming from zinc cell were carried out by using naftenic acid, D2EHPA and TBP. The pH giving, for each extractant, the best extraction yield was selected in order to compare the equilibrium curves. Experimental results show that all the examined extractants are very effective in zinc extraction if the process conditions are appropriately selected. In order to avoid an impure solution pre- treatment and to obtain the maximum ertraction yield the appropriate solvent can be chosen.

Jan 1, 1998

By Godwin M. Beene

Large scale mining operations started in Zambia in 1913 and rapidly expanded during the post 1930 period with the opening of several mining and processing plants on the present Zambian Copperbelt. As a consequence of poor tailings dumps design methods at the start of the mines, and in view of stringent Government Legislation pertaining to environment in the recent years, Nkana Mine has developed a unique method of dump construction at its current tailings depository, Tailings Dam 15A. This method has enabled the revegetation of the dump retaining walls while construction is still in progress, a situation which was not possible on the older dumps. Cowdung has proved to be a superior fertilizer for providing plant nutrients on the tailings. The new method of dump walls construction and walls rainwater runoff drainage system has almost eliminated tendency of gully formation which is common on older dumps, as rainfall on the Zambian Copperbelt comes in intense thunderstorms. The decanted water from the dump is discharged to the natural environment in a controlled fashion after ensuring that it meets the Zambian Government Statutory requirements.

Jan 1, 1999

Most of the world's zinc metal is produced via the roast- leach-electrowinning (RLE) process. The process is well established, but most of the sulphur in the sphalerite concentrates reports in the acid, which has to be stored and/or sold. There are significant incentives to develop a simpler process with much reduced acid generation. Ferric ion is a well known oxidant for most sulphides, in particular sphalerite, and it converts the sulphide to elemental sulphur. Based on stoichiometry, however, the amount of ferric ion needed to achieve acceptable zinc extractions is prohibitive for downstream zinc recovery from the leach solutions. The process suggested here makes use of less-than-stoichiometric ferric sulphate additions because the ferric ion is regenerated by sparging SO2/O2 mixtures. This regeneration can be effected in-situ in the leach vessel or outside the leach vessel. An example of the application of this new process is presented for a Canadian sphalerite concentrate assaying 60% Zn. The effects of temperature, ferric concentration and ferric ion regeneration are presented. Options to recover zinc from the leach solution are also briefly discussed.

Jan 1, 2000

By Mitsuhiro Ito

"To allow various wastes containing high levels of chlorine to be used as alternative raw materials for Portland cement, two practical methods of chlorine removal were developed. In the first method, chlorine is extracted from the wastes during the cement manufacturing process. In the second, ash-dust waste with high chlorine content is first washed and then dehydrated to cake before being introduced to the cement manufacturing process. This cake can be used as an alternative for some cement raw materials. By combining the two methods, various wastes previously considered unsuitable for recycling due to their chlorine content can often now be used in cement manufacturing plants. As such, these methods represent a major contribution to environmental protection as well as a solution to problems relating to the diffusion of heavy metals and dioxins from cement plants.1. IntroductionWaste generation levels have risen rapidly in recent years. in both the consumer and industrial sectors and today, the need for effective, efficient waste management is one of the most pressing and serious problem of today's society.The Japanese cement industry has reacted to the increase in waste generation by using certain materials as alternative raw inputs or fuels for cement production, in an effort to contribute to society and conserve energy resources.These wastes often contain non-negligible levels of chlorine and heavy metals, however, both of which are unsuitable for cement production. Depending on the element content, Heavy metals have a particularly negative effect -on cement quality; in addition, they can be released into the environment. Chlorine, on the other hand, is contained in large amounts in incinerated ash from household wastes as well as in certain plastics. Both substances are considered impediments in cement-production, not only because they reduce the quality of the cement produced but also because they impair operating safety on cement production lines.To address this problem, two practical technologies have been established for separation and recovery of chlorine components during cement pre-processing and production. This paper introduces the application of these technologies with a special focus on incinerated ash from urban wastes, a representative form of waste material having notably high concentrations of chlorine, heavy metals, and dioxins. We also outline the technologies enabling this material to be used as an alternative input to cement production."

Jan 1, 2000

By W. Marnette

Norddeutsche Affinerie is the largest West European copper producer with an annual output of more than 350,000 tonnes of refined copper, about half of which is produced from copper concentrates. However, in addition to concentrates, Norddeutsche Affinerie processes secondary raw materials and recycling materials which contain a combination of copper and lead. These materials were previously treated in blast furnaces, a technology which has meanwhile been superseded at NA by the electric furnace process, primarily owing to the necessity of complying with the increasingly stringent requirements for environmental protection.

Jan 1, 1994

By Tang Mo-tang

A new process for extracting indium from indium-zinc concentrates was proposed in this paper. The process can directly extract indium from removed copper solution by P204, and cancel the stage of removing iron in the traditional process because of using iron and part of zinc in the In-Zn concentrates for direct preparing high quality Mn-Zn soft magnetic ferrites. The technologies in the processes, such as leaching the neutral leached residues with high concentrated acid at high temperature, reduction ferric and removing copper, and extracting indium, were investigated. The results showed that total recovery ratio of indium has been increased from less than 70% in the traditional process to more than 95%. This process has the advantages of largely simplifying the procedure of indium extraction, zero draining off of iron residue and zero emitting of SO2. So this is a clean production process.

Jan 1, 2006

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997

By Elizabeth M. Ho

Oxidants are added in uranium leaching in acid media to convert iron(II) in solution to iron(III). Iron(III) has an important role in the leaching of uranium by acting as an electron transfer agent for the oxidation of uranium(IV) to uranium(VI). The oxidation of iron(II) to iron(III) in sulfate solutions using sulfur dioxide/oxygen (SO2/O2) was carried out under typical uranium leaching conditions (pH 1-2, 20-50°C) to confirm literature trends and this work was then extended to the use of SO2/O2 in the leaching of uranium ore. The oxidation rate was found to be dependent on the initial SO2/O2 volumetric ratio and the oxygen mass transfer rate, but was independent of the initial iron(III) concentration above about 200 ppm at pH 2. The presence of 55 ppm organic extractant (Alamine 336) decreased the reaction rate. The oxygen mass transfer coefficient (kLa) for the mixing tank system was measured and was found to decrease with increasing solids density in a 1 g L-1 MgSO4.7H2O solution.

Jan 1, 2003

By S. H. Castro

In 1997 Chile was the world's largest copper mine producer with around 3.4 million metric tomes of copper. Conventional technology (conminution-flotation- smelting-converting-electrorefining) for copper sulfide ores was used. For copper oxidized ores hydrometallurgical processes (heap leaching-solvent extraction- electrowinning) were employed. Consequently, the most important waste effluents include flotation tailings, gaseous emissions, smelter slags, acidic and alkaline wastewater, electrolytic sludges, solid residues from leaching, etc. The introduction of stricter environmental regulations are forcing the Chilean industry to minimise the generation of waste and promote cleaner production. Gas emissions such as SO2 and arsenic from smelters and process wastewater are the major problems at this stage. The environmental impact assessment of gas emissions in all six largest smelters namely Chuquicamata, Caletones, Potrenllos, Ventanas, Paipote and Chagres led to design a "decontamination plan." The implementation of this plan resulted in (i) the installation of sulfuric acid plants for SO2 abatement and (ii) the installation of electrostatic precipitators to remove arsenic oxides condensed from cooling gases. The aim of this paper is (i) to describe the type of waste associated to the various stages of the metallurgical processes and (ii) review the main abatement technologies used in medium and large size companies.

Jan 1, 1999

By N. S. Narayanan

Monazite, one of the major sources of rare earths, is normally opened by digestion with hot concentrated caustic soda solution. Caustic digestion dissolves phosphate and leaves a hydrated mixed metal oxides cake containing thorium, uranium and rare earths. By leaching this cake with hydrochloric acid at pH 3.0 to 3.2 bulk of the rare earths are preferentially removed and separated. The slurry left after removal of major portion of rare earths contains all the thorium and uranium present In the feed monazite. In addition this slurry also contains substantial quantities of rare earths. Solvent extraction tests were carried out to develop a process to separate rare earths, thorium and uranium present in the mixed chloride solution obtained by dissolving the above slurry in hydrochloric acid. Based on these tests a solvent extraction flow sheet was developed with di-2-ethyl hexyl phosphonic acid mono 2-ethyl hexyl ester as the extractant. The details of experimental work and results obtained are discussed and a flow sheet for processing monazite Incorporating the new process is suggested.

Jan 1, 1997