Search Documents

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Frederick W. DeVries

The author was invited by "60 Minutes Australia" to provide on-site technical background on cyanide, mining, and the environment, in their investigation of the January 30, 2000, spill at the Aurul gold-recovery site in Baia Mare, Romania. Some remarks on the incident ?and its implications surround a showing of the fourteen-minute telecast. The thrust of the TV reporter was that aspects of the dam implied the owners' use of standards Jess than would have been met for installations in technologically more advanced locations (like Australia). As a result, the public-relations impact is one of embarrassment for the world mining industry.

Jan 1, 1998

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2Si/MgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (P/M) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2JIm is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ forming process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm) and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Chuanfu Zhang, Liwei Liang, Yanxin Wu, Jinliang Wang

"According to the reaction shaft operation characteristics during the flash smelting process, 15 groups of slag samples containing high Fe3O4 were prepared by some chemical reagents, and then the slag viscosities were measured using a RTW-10 type synthetic test instrument for melt physical property by the rotating cylinder method. The effects of Fe/SiO2 ratio (mFe/mSiO2), Fe3O4 content (wFe3O4), Cu2o), MgO content (WMgO) and Cao content (wCaO) on the slag viscosity were also studied. Results show that slag viscosity is decreased with the increase of temperature, mFe/mSiO2, wCu2o, wMgO and wCao, and with the decrease of wFe3O4, under the range of slag contents: mFe/mSiO2 1.36~1.78, wFe3O4 17.83%~21.18%, wCu2o 3.51%~8.34%m wNgI 2.21%~6.57%m w/caI 6.22%~9.387% and temperature range if 1250 o/c~1450 oC. Only wFe3O4m and w/caO have great influence on the slag viscosity when temperatures as high as 1400 oC. Only wFe3O4 and wCaO have great influence on the slag viscosity when temperatures as high as 1400 oC or so. To form a freeze slag with higher viscosity inside the reaction shaft, wFe3O4 should be more than 20% and wCaO should be less then 6%.IntroductionSince its appearance in 1949, Outokumpu flash smelting technology has making continuous innovation and has become the most competitive intensified smelting technology [1], widely considered to be the standard clean smelting process [2]. At present, flash smelting technology is adopted to newly build or reconstruct most of the world's copper or nickel smelting enterprise [3]. Reaction shaft is the most important part of the flash smelting furnace. During the flash smelting process, reaction shaft must be able to withstand the following harsh conditions at the same time: 1) high temperature varying from 1400 °C to 1500 °C. 2) strong oxidative atmosphere containing 50% - 80% oxygen. 3) solid particles and melt with speed up to l00 m/s. 4) high acidic or basic slag with strong chemical corrosiveness. 5) smelting gas containing 50% - 80% SO2. 6) matte with strong dissolution."

Jan 1, 2012

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"The Center for Advanced Mineral and Metallurgical Processing is developing membrane production technology based on autocatalytic reduction of palladium from solution onto a unique, porous substrate. Surface membranes and catalytic structures are critically important to applications that range from hydrogen purification membranes to petroleum refining. Autocatalytic reduction processes represent a cost effective method of producing stable surface layered structures that have good working lives. These attributes are particularly important in the production of palladium alloy purification membranes used in hydrogen production. Although considerable research has investigated the interaction of hydrogen and palladium alloys, the mechanisms in play while the membranes form are not well understood. Preliminary research has identified three distinct deposition mechanisms and it appears that substantial control over the resulting membrane is possible.IntroductionPalladium-based membranes separate hydrogen from other gases because hydrogen is uniquely soluble in and readily passes through bulk palladium. As currently produced, palladium-based membranes are expensive and have short service lives. These circumstances are due in part to the lack of a complete understanding of palladium or palladium alloy deposition. The Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production.In membrane production, the palladium requirement depends on substrate surface properties such as surface chemistry, porosity, and roughness. Thin, defect-free membranes have been successfully produced on substrates of porous glass, alumina, and stainless steel. However, the differences in the thermal expansion coefficients of palladium membranes and porous glass or alumina substrates cause problems at operating temperatures. The use of stainless steel substrates is advantageous because stainless steels have thermal expansion coefficients similar to that of palladium and they are stable at the required operating temperatures (Wicke, E., Brodowsky, H. and Ziichner, H. ). Stainless steel is also readily available and relatively inexpensive."

Jan 1, 2012

By K. P. V. Lei

The U.S. Bureau of Mines investigated a hydrothermal sulfidation procedure to recover lead and silver from plumbojarosite. The plumbojarosite, generated during pressure-oxidative leaching of zinc concentrate in a commercial operation, contained, in percent, 25.4 pb, 18.8 Fe, 1.4 Zn, 29.5 SO,2-, 3.2 s?, 13.4 total sulfur, and 7.4 oz/ton Ag. The sulfidation was conducted in an autoclave and converted the plumbojarosite to amorphous iron oxide and liberated the lead and silver as sulfides. The best operating conditions were using 50 9 of plumbojarosite and 7 pct s? (2.04 9 S? added) in 500 mL of 2.0 mol/L NH3, 150? C, and 1 h. The sulfidation product contained, in percent, 37 Pb, 28 Fe, 6 S2-, 2 SO,2-, and 11.2 oz/st Ag. Ferric chloride leaching extracted 98 pct Pb and 97 pct Ag from the sulfidation product.

Jan 1, 1990

By Baicheng Liu, Houfa Shen, Wensheng Li

"In order to understand the formation of macrosegregation in steel ingots, a mixture model has been developed which accounts for coupled mass, momentum, species, and energy transport to describe the sedimentation of free equiaxed grains during solidification. In this model, the mushy zone is divided into the slurry and porous regimes according to a solid packing fraction. Settling velocity of equiaxed grains in the slurry regime is given by an explicit expression. The solidification of a binary steel ingot (Fe-0.36wt.%C) with a two-dimensional geometry is numerically simulated. It is demonstrated that the predicted macrosegregation patterns agree to some extent with classical experimental results. Further refinement of this model is still necessary for realistically simulating steel ingot solidification.IntroductionModeling macrosegregation in steel ingots is still a challenging study, mainly due to the length scale of the products and the complexity of global multiphase transport phenomena coupled with microscopic solidification kinetics [l]. The thermal-solutal convection and the motion of equiaxed grains are the two main mechanisms responsible for macrosegregation. But there are few models that deal with the motion of equiaxed grains, which is confirmed as the main phenomenon that explains the negative macrosegregation along the centerline of large steel ingots [2]. A model which takes into account melt convection and grain sedimentation was first proposed by Beckermann and co-workers ([3], and references therein). More recently, similar multiphase solidification models with advanced nature have been presented by Wu and Ludwig [1,4] and Combeau and co-workers [5,6]. It is known that the application of these sophisticated models to steel ingot casting is at its beginning.In this paper, a solidification model based on continuum mixture approach, using much less sophisticated relations to obtain the settling velocity of free equiaxed grains, has been proposed in order to predict the macrosegregation in steel ingots. The model is applied to simulate the solidification of a binary steel ingot with a two-dimensional geometry, and preliminary modeling results are presented."

Jan 1, 2011

By Tengfei Qi, Liqiang Fan, Huiqing Tang

A new method to process the oolitic high phosphorus iron ore for phosphorus removal has been proposed in this research. It is an integration of direct reduction and melting separation with carbon-containing pellets prepared using biomass char. Experiments of direct reduction were preceded using a tubular furnace and three parameters were investigated and they were reduction temperature, biomass char adding ratio(molar ratio of carbon to oxygen） and atmosphere. Results show that the optimum condition is of reduction temperature is 1373 K, biomass adding ratio 0.9, PCO2/PCO 1.0 and reduction time 15~25 min. Under this condition, the reduced briquettes with a metallization of 75.0~80.0 % and a residual carbon content of 0.69~0.11 wt% could be obtained. Subsequent melting separation experiments were conducted using a Si-Mo high temperature furnace. Results show metal with phosphorus content of about 0.4 mass% could be obtained from the reduced sample.

Jan 1, 2015

By Jin-tao Gao

In order to recover Ti resource from titanium bearing blast furnace slag, a new technology to separate perovskite phase from CaO-TiO2-SiO2-Al2O3-MgO system by supergravity is researched. In the condition of gravity coefficient of 750g, treatment temperature of 1305°C and time of 20min, the significant layers appear in samples which are obtained by means of centrifugal treatment. Along the direction of the supergravity, the volume fraction of perovskite phase increases gradually, and the equivalent diameters of perovskite phase crystals increases with the area approaching to the bottom of the sample. It is indicated that TiO2 is enriched in the bottom of sample as concentrate with a recovery ratio of 74.05% by supergravity treatment.

Jan 1, 2014

By Dong-dong Liu, Jian-ping Niu, Qi Liu, Shu-sen Cheng

A numerical model was developed to simulate the three-dimensional heat transfer in the belly and lower shaft region of the blast furnace wall consisting of copper steel composite stave, packing and shell. The temperature distribution of copper steel composite stave without the slag layer or refractory lining was investigated and then compared with the copper stave. The results showed that copper steel composite stave can satisfy the requirement of overheatingfree and had an analogous heat transfer behavior as copper stave but more stable cooling intensity. This model had been validated by the good agreement between the computed and measured temperature in the thermal test.

Jan 1, 2015

By Yongfeng Jia

Lime neutralization and co-precipitation of As(V) with iron(III) is the most widely used and most economical method for the removal of arsenic from mineral processing solutions and effluents. However, the arsenate fixation mechanism in the coprecipitated solids is not fully understood. It was suggested by various researchers to be a ferrihydrite precipitation process during which arsenate is removed by adsorption on ferrihydrite. In this study, XRD, EXAFS and microprobe were employed for the speciation of arsenic and the effect of various factors on arsenic solubility was also investigated. The results indicate that coprecipitation is a more complicated process than simple adsorption resulting in lower arsenic solubilities. Poorly crystalline ferric arsenate was observed for the first time to be present in the coprecipitated solids. In case of lime as base, there exists some type of Ca-Fe-arsenate association. A general term ?coprecipitate? is suggested to describe the precipitated arsenic-bearing solids instead of those widely used specific terms ?arsenical ferrihydrite? or ?arsenic-bearing ferrihydrite?.

Jan 1, 2005

By Y. Kumagai, F. A. Souza

"Electroless plating process has been used in many fields such as automobile and electronic industries. Solutions used in these processes must be disposed or treated. Commonly, in these solutions metal ions, organic materials and others chemicals are in very high concentration. It is very difficult to keep the environmental regulations for disposal of these materials, and the cost of the plating process becomes higher.The objective of this study was to investigate the recovery of components of those baths in order to decrease the cost of the plating process as well as to meet the environmental regulation.In this study the recovery metal ions, sulfate ions, phosphite ions and organic compounds were investigated. Organic compounds used in electroless plating solutions are the organic acids. In this work the solvent extraction of the most used organic acids included citric, lactic, succinic, tartaric and malic was studied. The solvent phase considered in these studies was ethyl acetate.About 95% of the metal ion was recovered by chemical plating onto mica powder. The hypophosphite remained is oxidized to phosphite and with the sulfate ion, both are recovered as calcium salts by selective precipitation in pH 7 and 2 respectively. Organic acids were recovered by solvent extraction using ethyl acetate as solvent phase and the best results were for lactic acid and succinic acid.Along with this study, was developed the analytical parameters to perform wastewater analysis by using Ion Chromatography, High Performance Liquid Chromatography (HPLC), Fourrier Transform Infrared Spectroscopy (FTIR). Ion chromatography was used to perform analysis of sulfate and phosphite ions in liquid matrix, HPLC was used to perform analysis of organic acids in liquid matrix and FTIR was used for characterization of the solids obtained in the recovery processes."

Jan 1, 1997

By Li Xi

This paper describes how a back-propagation neural network is built for predicting the properties of engineering materials from their other properties, compositions or processes. A predicted result of the impact toughness of a 12Cr-2Ni-1.5Mo stainless steel from its tempering temperature is presented. Furthermore, the combination of this neural network for prediction is able to supplement the unpredictability of the expert system outside its domain of expertise. An integrated system may perform more intelligently and solve more complex problems as well as human expert, in some case even better.

Jan 1, 1992

By Alan James Parker

Chalcopyrite can be converted to pure copper by the following five steps. An exothermic sulfation roast of chalcopyrite; leaching of cupric sulfate from the calcine with dilute acid; precipitation of Chevreul's salt and or other copper sulfites with ammonium sulfite or precipitation of crude copper by autoclaving ammonium sulfite and cupric sulfate at 150°C; dissolution of Chevreul's salt, or the crude copper, as cuprous sulfate, using acidic cupric sulfate in an acetonitrile-water solution as oxidant; precipitation of pure copper by thermal disproportionation of the cuprous sulfate solution. Acetonitrile and acidic cupric sulfate solution recycle. Advantages over conventional processes include lower cost, lower energy consumption as waste heat, sulfur removal as ammonium sulfate or gypsum, rather than as sulfur dioxide and rapid throughput. The net reaction is: 2 CuFeS2 + 4H20 + 15/2 02 + 8 NH3?2Cu + 4 (NR4)2 SO4 + Fe2O3

Jan 1, 1976

By Bingyi Bai, Lifeng Yang, Yanling Guo, Jieyu Zhang, Guoding Gao

In terms of special resources with iron, niobium and rare earth coexisting in Baiyuneboite, the new smelting technology of ferrocolumbite was studied. Reduction experients for the Baiyuneboite and explores ore phase change of Baiyuneboite in the process of reduction was conducted with graphitic carbon as the main reducer and a temperature below 1000 ℃. Moreover, it studies the influence of reducer, roasting temperature and grind fineness on the reduction as well as focuses on the evolution course of iron phase. Through the analysis on in-situ XRD of the raw ore and carbon addition ore, it also develops microstructure change rules of Fe ore phase and ore phase of paragenetic elements for composite ore(Ca, Si, Nb, F) in the process of reduction roasting. In addition, the impacts of temperature on the reduction process are also discussed. With regard to minerals of different particle sizes, the thesis will explore their ore phase changes and microstructures after 10 hours’ reduction under 900 ℃.

Jan 1, 2015

By Chao Li, Qian Li, Yong-bin Yang, Kai Li, Qiang Xie, Yuan-yuan Zhu, Dong-ye Li, Qi-bing Tan

"The permeability of sintering mix is a vital technological property in sintering process. However, it can only be measured by off-line method on samples picked from the production. In order to acquire the properties of sintering mix accurately, on-line measuring of permeability is urgently required. Based on the reflection characteristics of bed permeability on pipe flowing parameters, a new method is presented in this paper for on-line measuring of sintering mix permeability. The measurement can be performed by blowing gas flow in the bed with the measuring pipe. Measuring results are obtained by picking the data on flowing rate and pressure in the pipe. The function of flowing rate to pressure may be certain for samples with the same permeability. Thus, the permeability was determined by contrasting this function to the result of off-line measuring, and the relative coefficient or R2 value was more than 99%.IntroductionThe permeability of sintering mix is a vital technological property in sintering process, which directly determines production and quality of sinter, or even determines whether the sinter production is carried out smoothly [1,3].The permeability have more obvious influence on vertical sintering speed, which is mainly related to air quantity passing through material bed. Under certain inducing capacity and negative pressure, the vertical sintering speed mainly depends on the permeability of sintering mix. Low permeability may make burning through point of sintering move back, and the sinter mix cannot be burnt through. High permeability may make burning through point of sintering move forward, improving production efficiency by increasing the speed of sintering machine [4] Good permeability means a small resistance of fan ,reduction of negative pressure of sintering machine, and full contact between air and sulfide, which can strengthen physical-chemical reaction during sintering process and increase desulphurization rate. In gas well through material layer process, gas-solid desulfurization reaction and gas-solid-liquid heat exchange are completed and hot gas through the combustion zone supplies the sintering process with heat. Finally uniform sintering of the material layer in height and width direction is achieved [5] While high permeability index leads to weak sinter strength, fast sintering speed, short residence time of high temperature region and little liquid phase. Moreover, liquid phase in the fast cooling process is too late to fully crystallize but forming glass phase which is harmful to sinter strength as well. Bad permeability means a big fan resistance and increase of negative pressure of sintering machine, which make the air pass through material layer difficultly. When air and mix contact difficultly, removal of sulfide reduces so that desulfurization is incomplete. Meanwhile, low caking efficiency, slow sintering speed and easily burnt sinter , reduce sinter output. Therefore appropriate permeability of sintering mix is the premise of stable burning through point and satisfactory sinter output and quality."

Jan 1, 2013

By R. G. Robins

The effective removal of arsenic(V) from process streams and waste waters by precipitation with excess iron(II1) is sometimes attributed to the formation of basic ferric arsenates. The authors have investigated this system extensively using a variety of techniques and conclude that the solid phase produced is iron(II1) oxyhydroxide (ferrihydrite) with arsenic(V) adsorptively bound to the 2-3 nm particles.

Jan 1, 1992

By Tam Tran

Over the last decade, halide (chloride, bromide and iodide) systems have been evaluated as alternative lixiviants for the processing of gold to replace cyanidation which has been widely used in commercial practice. This paper first reviews the development of processes promoted by Kaljas Ltd / Lachlan Resources (Australia) and Great Lakes Corp (USA) using different bromide/bromine systems in the early 1990's. Several research groups subsequently evaluated the use of iodide/iodine and chloride/chlorine for gold extraction, showing similar characteristics of gold/silver dissolution and recovery. A critique is :given on the advantages and the ,shortfalls of halide systems as alternative lixiviants. The stability of gold? halide complexes is discussed, based on practical experience and thermodynamic modelling of their speciation, The iodide system provides the most stable gold / silver complex for easier handling. However, the cost of iodide inhibits its application for are processing. In this critique, emphasis is given on the cheapest system, which involves the use of chloride for leaching (in conjunction with an appropriate oxidant). However the chloride-base leachant has a major drawback which is related to the unstable nature of gold chloride in a reducing environment.

Jan 1, 1998

By Tom W. Gonzales

Magma Metals Company commissioned a 3000 tpd Outokumpu flash smelting furnace in July 1988. Through September 1992 the PSP has smelted a first campaign record 4.1 million tons of concentrate. This paper discusses modifications made to the original process equipment to overcome design flaws as well as future design changes currently under consideration.

Jan 1, 1993

By Marco Olper

After two years of extensive research a new and innovative modification to the CX-EW process has been exploited. This process, called CX-EWS, avoids completely all the critical aspects of the previous process which affected the cost of the energy, of the chemicals and of The maintenance of the insoluble anodes. All these benefits reflect a saving of about 30% of The operating costs compared to the present traditional production and allow for a total operating costs of less than 6.5 cts/lb. lead (net of raw material cost). With this new technology it is allowed for the first time the treatment in the same plant facilities of both primary lead sulphide concentrate and spent batteries. The paper describes the technical and economical aspect of the new process with a feasibility study for 150,000 t/y spent battery facility throughput.

Jan 1, 1995