Search Documents

By Jewel Gomes

Produced water (PW) is salty water trapped in the reservoir rock and brought up along with oil or gas during production. It subsists under high pressures and temperatures, and usually contains hydrocarbons and metals. Therefore, it must be treated before being discharged to surface water. Different techniques are being used to treat PW through phase separations, system control and design, and chemical treatments. In this paper, we discuss our experimental results on treating PW through electrocoagulation (EC). The performance of EC was investigated for the reduction of chemical oxygen demand (COD) and metal ions. Effects of different electrodes, residence time, current density, and pH were also studied to optimize the treatment conditions. Different kinds of cleansing agents, such as lime and borax were used to break the buffering effect encountered during treatment. FTIR, SEM/EDS, and XRD were used to characterize the EC-floc and thus to elucidate removal mechanisms.

Jan 1, 2009

By Naixiang Feng, Shaohu Tao, Zhihui Wang, Yuezhong Di

"A novel vacuum aluminothermic reduction lithium process was developed in present work which used lithium carbonate, alumina and calcium oxide as raw material. The process mainly contained three steps. The first step is that LiA102 clinker is prepared in ambient environment, then metal lithium is vacuum extracted from LiAl02 clinker with aluminum power as reducing agent, and the last step is that alumina is leached from the reduction residue with a mixture of sodium hydroxide and sodium carbonate. The results show that the lithium reduction ratio can be over 95% under the conditions of reduction temperature 1423K, reduction time 3h, and aluminum excess 20%. The main components of reduction residue are CaO· Al203 and 12Ca0·7Alz03. The alumina leaching rate of calcium aluminate in residue is over 80%. High-whiteness aluminum hydroxide can be obtained by carbonation precipitation of the reduction slag leaching solution.IntroductionWith a density about half of water, lithium is with the lowest density of all solids, mere 0.5 g/cm3 at 20 °C [l]. Lithium is widely used in aerospace, aviation, nuclear-generated power and electric battery industry. Nowadays, over 90 % of the world's primary lithium is produced by molten salt electrolysis [2-4]. But the development of molten salt electrolysis will be effected by some factors: cost, environment, and so on. Vacuum thermal reduction may be used extensively in future because of its low-energy consumption, high-purity and short-cycle."

Jan 1, 2013

By Luis M. Chia

The direct dissolution of zinc in an organic solution of di-(2-ethylhexyl) phosphoric acid (D2EHPA) and kerosene was studied. The objective was to gain a better understanding of the fundamentals involved in the anodic step of the galvanic stripping process. Results showed that metallic zinc does dissolve spontaneously at ambient temperature by an electrochemical mechanism and the presence of additional oxygen activated the process. When oxygen was removed by prior nitrogen sparging, dissolution did not occur indicating a depolarizing cathodic reaction is necessary. The concentration of water in the organic also affected the rate of dissolution. A factorially designed experiment was made using four variables at two levels selected by evaluating results from previous screening tests. D2EHPA concentration, surface area and agitation were all found to be significant for the values chosen. Temperature was less significant and it was found that zinc dissolution is probably a diffusion or mixed controlled process, as indicated by the calculated activation energy of 6 kcal/mole.

Jan 1, 1995

By Lætitia H. Delmau

SXFIT is the latest in a series of programs developed in our group to model solvent extraction systems of increasing complexity. SXFIT permits the user complete freedom to define the constituents from which the composition of each phase is to be specified in the data and from which all species of a model for a system are assumed to be formed. Activity coefficients in the nonaqueous and aqueous phases, water activity, apparent molar volumes of aqueous species, and solution density needed for the conversion of concentration from the molarity to the molarity scale are all taken into account by the program. Several extraction systems relevant to nuclear-waste treatment were modeled successfully using this program. As an example, the cesium extraction efficiency of the CSSX process chosen by the USDOE for cesium removal from high-level waste stored at the Savannah River Site can be predicted correctly for varying feed composition.

Jan 1, 2003

By Youngkook Lee

The precipitation kinetics of NbC in ferrite matrix of the Nb microalloyed steel was investigated experimentally and numerically. The mole fractions of NbC precipitates formed at different isothermal temperatures were measured as a function of holding time by electrical resistivity test and were compared with both a mathematical model based on time-dependent nucleation and growth rates and the hardness. There is a good match among the calculated and measured precipitation kinetics of NbC and the hardness. The isothermal precipitation-temperature-time diagram of NbC in ferrite matrix of the Nb microalloyed steel was newly generated. Keywords: Precipitation, Carbide, Ferrite, Nucleation, Growth, etc

Jan 1, 2003

By J. E. Wey

Extraction of cobalt from cobalt sulfide and cobaltite flotation concentrate from the Blackbird Mine, Idaho, was investigated using an adapted strain of Thiobacillus ferrooxidans. Cobalt extractions as high as 100% were realized in the inoculated experiments, whereas only 4% extraction was obtained in the sterile run. The influence of pulp density on the rate and extent of cobalt extraction was also determined. It was found that the extraction of cobalt followed predominantly the indirect mode of bacterial activity. In this process, ferric iron oxidizes cobaltite to cobalt sulfate and ferric arsenate while being reduced to its ferrous state; the bacteria continuously re-oxidize ferrous to ferric iron. Electrochemical measurements using cyclic voltammetry suggested that cobaltite oxidation involved a number of intermediate reactions.

Jan 1, 1993

By Migen Dibra

Antitrust and competition laws are designed to protect the free markets and promote competition in order to assure a dynamic and efficient economy and to provide competitive prices for quality products and services. They apply to mergers and acquisitions as well as to joint ventures especially among competitor companies who possess market power and these include collaborations on research and development. If it is determined that these actions are likely to substantially prevent or lessen competition the courts might dissolve, stop, alternate them, etc. Two new factors affect this process today: The role of new technologies and the markets globalization. They both have a considerable effect on the way these laws are interpreted by the courts and on their eventual amendments in order to reflect the new reality. A new applied technology and the globalization separately or together may change the factors that determine how anticompetitive a merger or acquisition between competitors may be and may also serve as a basis for amending the antitrust and competition laws. In this paper, a short review of the recent mergers and acquisitions of various companies has been carried out along with an abridged analysis of the current antitrust and competition laws in USA, Canada and European Union in the view of their capacity to handle the new reality. Some related court decisions are also examined and several examples are given in order to illustrate the influence of new technologies and globalization in interpreting the existing laws and on their amendment possibilities.

Jan 1, 2006

By Michel G. Drouet

Dross, a major by-product of all processes involving molten aluminum, forms at the surface of the molten metal as the latter reacts with the furnace atmosphere. It generally represents 1 to 5 wt% of the melt, depending on the process, and contains on average about 50% free aluminum dispersed in an oxide layer. Since aluminum production is highly energy-intensive, dross recycling is very attractive from both the energy and the economic standpoints. The conventional recycling process using salt rotary furnaces is thermally inefficient and environmentally non-acceptable because of the production of salt slags. Hydro-Quebec has developed and patented a new salt-free technology using a rotary furnace heated by an electric arc between two graphite electrodes, called DROSCAR®. A 600-kW pilot plant in operation at LTEE is in use to demonstrate the process. This process provides aluminum recovery rates over 90%, using a highly energy efficient, environmentally sound production method. In 1994, 400 tonnes of aluminum dross were treated in this facility and several tests on various types of dross have also been conducted in early 1995. A report on the results will be presented.

Jan 1, 1995

By Vladimir Mindin

Simulation of complex equilibria is usually done in the P-T-X coordinates, where "Xu is the amount of individual chemical components in the system. This approach is not productive in some very important cases: (i) investigation of "open" systems, (ii) determination of coordinates (trajectories) of mono-variant points, among others. To solve these and some other problems, we use the idea of chemical potentials of elements (CPE) of the system. A system of different coordinates axes (CPE-axes ) leads to a new strategy of simulation, observing the results of the simulation, and to efficient technology of compressing and storage the data of the simulation.

Jan 1, 1994

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, a three dimensional finite-volume model has been established, and the fluid flow and heat transfer in the super-wide slab mold (cross section 3250mm×150mm) of Nanjing Iron and Steel Company has been simulated. The basic feature of flow and temperature field in a super-wide mold has been analyzed, and the effects of mold width, the submergence depth of SEN, outlet angle of SEN, casting speed, superheat and cooling rate on the flow and temperature field have been investigated. The results by comparing several simulated calculations for 3250mm×150mm slab show that a more proper fluid flow and temperature field in the super-wide mold can be obtained with 15°outlet angle, 120~150mm submergence depth of SEN and 1.2~1.4m/min casting speed. The results through numerical simulation provide a theoretical basis for optimizing the configuration design of SEN and choosing reasonable processing parameters for the continuous casting mold of super-wide slab.

Jan 1, 2009

By Giulio R. Altoé, Sergio N. Monteiro, Ygor M. Moraes, Rômulo L. Loyola, Frederico M. Margem, Gabriel O. Glória

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of PALF fibers were evaluated. Composites reinforced with up to 30% in volume of long, continuous and aligned PALF fibers were tested in an Instron machine at room temperature. The fracture was analyzed by SEM. This one revealed a weak fiber/matrix interface, which could be responsible for the performance of some properties. The results showed significant changes in the mechanical properties with the amount of PALF fibers.

Jan 1, 2015

By R. C. Hubli

Copper (II) chloride has proven to be an efficient lixiviant for copper sulphide ores and secondary sources of copper such as scrap. Nickel sulphides are generally associated with copper ores and copper-nickel matte is an intermediate product of processing mixed sulphides. While the copper species in aqueous chloride media are present as chlorocomplexes, the presence of nickel as Ni++ offers effective separation between the two by solvent extraction techniques. Oxidation of millerite by cupric chloride in sodium chloride solutions has been studied as a function of rate of agitation, leaching time, temperature, acid concentration and total initial cupric concentration. The reaction has a 1/2 order of dependence on initial cupric concentration in the range of 0.0 to 0.5M. The activation energy for the temperature range 333 -363 K has been found to be 59.2 kJ/mol with chemical reaction at the unreacted mineral surface as the rate controlling step. The rate expression, according to the shrinking-core model, for initial cupric concentrations between 0.0 to O.5M, is evaluated as

Jan 1, 1996

By Kota Nakashima

Residues from titanium smelting tend to contain scandium. The scandiumis discarded because no suitable process exists for its recovery from the residue. Valuable-metal recovery from discharged residue is critical for environmental conservation and to achieve a sustainable society. Since 2015, JXNippon Mining&Metals has been developing a process for scandium recovery from the residue of a titaniumsmelting process. The process consists of the following steps: scandium concentrating by classification or neutralization, selective scandium leaching, impurity removal by neutralization, solvent extraction of scandium by using D2EHPA, purification, and roasting. We optimized the above steps to achieve an effective process to obtain scandium oxide (Sc2O3). In this paper, we introduce results from the bench-scale test of the scandium recovery flowsheet developed by JX Nippon Mining & Metals.

By C. O. Bounds

Management of emission control dust from electric? arc furnace (EAF) steelmaking as an RCRA-EPA listed hazardous waste places economic and environmental pressures on the steelmaking industry. Horsehead Resource Development Company, Inc. (HRD) serves the industry by recovering nonferrous metals from the dust in rotary kiln plants in Palmerton, PA and Chicago, IL, and has demonstrated the commercial viability of its patented coal-fired FLAME REACTOR Process. However, because of location and/or regulation, many steelmakers could be more economically served via on-site processing of its dust. Therefore, in 198-7, through a contract with the Gas Research Institute, HRD embarked on a program to develop a gas-fired reactor and test a prototype unit. The development program has successfully proven the environmental, technical and economic performance of the concept. Consistently high zinc, lead and cadmium recovery to an oxide concentrate as well as production of a nonhazardous, delistable slag have routinely been achieved. The gas-fired FLAME REACTOR field experiment results and the economic performance of on-site or smaller regional plants will be highlighted.

Jan 1, 1990

By Hongxu Li, Pu Liu, Hao Bai, Daqiang Cang, Lihua Zhao

"Coal, as the main energy in ferrous metallurgy, is consumed on a large scale and great amount of CO2 is emitted likewise. In this paper, a model, based on carbon balance, was developed for CO2 emission analysis, with data obtained from a typical integrated steelworks in China. The result shows that, CO2 emissions increase almost constantly with the growth of steel production. However, coals of different classes and product variety in the steelworks exerted an influence on CO2 emissions. Furthermore, three scenarios, including natural gas instead of coal for power generation, EAF process partly replacing integrated steelmaking, and feasible techniques applied to achieve lowest process energy consumption (FLPEC), were assumed to seek possible ways of carbon emission reduction. The result proves that the second scenario is most effective. If 40% of the steel product could be from EAF process, CO2 emissions would be reduced by 45.07%.IntroductionGlobal warming has become a global environmental problem, which is generally caused by excessive emission of greenhouse gases, such as CO2, generated from human activities and industrial processes. It is estimated that about 7% of global CO2 emissions was from iron and steel industry. Further, if the ore and coal’s mining and transportation are included, the CO2 emissions would reach 10%[1]. In general, the relationship between energy saving and CO2 emission reduction is positive correlation. However, in iron and steel enterprises, due to different types of energy resources like coal, heavy oil, natural gas, the consumption of which will generate different amount of CO2, are used, different energy consumption structure in iron and steel enterprises will lead to difference of CO2 emissions.In order to assess the CO2 emission reduction potential of China’s steel industry, Ke Wang etc.[2] developed a model using LEAP software to generate 3 different CO2 emission scenarios for the industry from 2000 to 2030. LEAP is a scenario-based software tool for integrated energy-environment and greenhouse gas mitigation analysis. The amount of CO2 emissions was obtained by the following equation:"

Jan 1, 2011

By Jürgen Antrekowitsch, Thomas Griessacher

The recovery of valuable metals from residues like dusts and sludges is nowadays state of the art. Depending on the complex constitution, a recovery of different metals can – in the majority of cases – only be performed with considerable energy input in high temperature processes together with insufficient yields and newly generated residues. Often, the behavior of the dust or sludge in the process during melting or reduction is unknown. In this work, a detailed characterization of selected residues like steel mill filter dusts, cupola furnace dusts and leaching residues is done. The different steps of getting from solid particles into a homogenous liquid phase were investigated. Although high temperature processing leads to high reaction speeds, the complexity of residues keeps the system away from thermodynamic equilibrium. With this research program, some basics are generated to understand smelting and reduction and the gap between thermodynamical calculations and real behavior can be explained.

Jan 1, 2008

By Junzo Hino

Most of the waste that contains a small portion of copper is landfilled. The recycling process of copper from the waste, such as shredder residue, should be developed in order to save mineral resources and prevent environmental pollution. Shredder residue, generated from disposed automobiles and electric appliances, consists of many types of plastics, glasses and metals. The combustion heat of plastics is efficiently used for smelting in the recycling process that consists of melting and reduction. Because the waste contains numerous components the knowledge of the distribution behaviors of the main components is necessary to develop the recycling process. The distribution behaviors in the recycling process are evaluated by using the thermodynamic calculation program, HSC Chemistry. The calculation results are compared with the practical operation data of the recycling process and discussed.

Jan 1, 2003

By Sheng-li Wu, Guo-liang Zhang, Bo Su

One of the major challenges for the Canadian Gen IV Super-Critical Water-cooled Reactor (SCWR) concept is the selection of fuel cladding materials. The Canadian SCWR concept will operate at a core outlet temperature of 625 oC and 25 MPa of pressure with peak cladding temperature reaching as high as 800 oC. Corrosion resistance is an important factor for material selection. Austenitic stainless steels that contain Cr contents greater than 18 wt.% are generally considered to provide adequate corrosion resistance. In this work, the pressure dependence of the corrosion of austenitic stainless steel 310 containing 24 wt% Cr is assessed at 625 C for exposures of 1000 hours to evaluate the suitability of superheated steam as a surrogate for supercritical water at 25 MPa. Transmission Electron Microscopy (TEM) revealed that 310 exposed to different pressure conditions at 625 oC. (i.e., 0.1, 8 and 29 MPa) had generally the same type of the oxide structure, i.e., a Cr-rich oxide with the spinel structure on outer surface adjacent to the water phase. The material exposed at 8 and 29 MPa had a double layer oxide structure, with the outer oxide layer having a much larger grain size, while the samples exposed at 0.1 MPa showed only a single spinel-phase oxide layer. Cr-depleted recrystallized austenite grains were found underneath the spinel phase oxide. The adjacent large-grained austenite substrate had M23C6 carbides in the grain interior. The implications of these results are discussed.

Jan 1, 2015

By A. W. Bryson, K. C. Lenthall

"With the growth in the use of cobalt in industry, interest in its extraction and recovery has increased. With this increased interest comes the need for a fundamental knowledge of the processes involved in the recovery of cobalt metal. This paper examines the effects of cobalt concentration, catholyte pH, operating temperature and current density on cobalt electrowinning with respect to the current efficiency, cell potential and nature of the cobalt deposit. It is found that the cobalt concentration and catholyte pH affect the current efficiency, while current density and temperature affect the cell potential and thus the specific power consumption. Pitting on the deposit is affected by the catholyte pH and the operating temperature. Furthermore, the effect of feed flow-rate on catholyte pH, and thus current efficiency, is investigated. A model to predict the cell performance, which includes the flux of hydrogen ions through the diaphragm, is proposed.IntroductionCobalt metal is a silvery transitional metal found between nickel and iron on the periodic table. Due to its resistance to corrosion and other properties under high temperatures and its good work-hardening characteristics, it is favoured in alloys used in high temperature applications. These include aerospace, aircraft and high speed tools. Other applications include its use as a colourant in glass and ceramics, a drying agent in paints, a nutrient for livestock, a catalyst in the petroleum industry and, in the medical field, in prosthetics and radiology.The main deposits of cobalt are found in Central Africa, specifically Zaire and Zambia, although deposits also occur in Morocco, Canada and Australia. The cobalt is generally associated with other transitional metals including nickel, iron and copper. It is generally extracted by hydrometallurgical means and recovered from solution by electrowinning or hydrogen reduction. Little data [1-2] exists in literature on the electrowinning of cobalt from aqueous solutions. This paper investigates the effects of various operating conditions on the current efficiency, cell potential and deposit nature under continuous operation."

Jan 1, 1997

By Michael Zinigrad

The quality of metallic materials depends on their composition and structure and these are determined by various physico-chemical and technological factors. To effectively prepare materials with required composition, structure and properties it is necessary to carry out a research in two parallel directions: Comprehensive analysis of thennodynamics, kineties and mechanisms of the processes taking place at the solid-liquid-gaseous phase interface during welding processes and development of mathematical models of the specific welding technologies. We have developed unique method of mathematical modeling of phase interaction at high temperatures. This method allows us to build models taking into account the thennodynamic characteristics of the processes, the influence of the initial composition and temperature on the equilibrium state of the reactions, the kinetics of heterogeneous processes, the influence of the temperature, composition, hydrodynamic and thennal factors on the velocity of the chemical and diffusion processes. The model can be implemented in the optimization of various technological processes in welding, surfacing, casting as well as in manufacturing of steels and non-ferrous alloys, materials refining, alloying with special additives, removing of non-metallic inclusions.

Jan 1, 2003