Search Documents

By E. Krystad, G. Tranell

"The kinetics of boron removal from liquid silicon during slag refining, as a process step in the production of solar grade silicon, has been investigated by means of small scale mass transfer experimental series at 1600°C, using a graphite crucible. The slags were SiO2-CaO based, with or without addition of approx. 19 wt% MgO. Experiments were carried out at slag-metal ratios of 1 or 2, where the silicon initially contained approx. 250 ppm boron. The metal-slag mass transfer coefficients for boron were found to be in the order of 1-3 · 10-6 m/s and were largely influenced by slag composition. The mass transfer rate was higher for the MgO-containing slag than the slags without MgO. The final equilibrium distribution of boron between metal and slag, LB, was determined to be in the order of 2.3-3.3.I. INTRODUCTIONRecent years have seen a race in industry and research aimed at obtaining a reliable metallurgical route for production of silicon for solar cells (SoG-Si) from metallurgical grade (MG) silicon. Metallurgical routes can successfully challenge the traditional chemical routes for production of SoG-Si if they generate metal of sufficient purity while being less expensive in terms of production cost and energy consumption. Efficient removal of boron is one of the greatest obstacles in the refining of silicon by a metallurgical route, because the segregation coefficient of boron in silicon makes directional solidification unfeasible; in addition, the vapour pressure of boron is not high enough for removal by vacuum refining. However, the thermodynamic properties of boron makes removal from silicon by oxidation possible, and thus the process of slag refining of silicon has been receiving increasing attention as a method for boron removal."

Jan 1, 2012

By Sylwia Zymankowska-Kumon, Rafal Danko, Józef Danko, Mariusz Holtzer

"Burning of ceramic materials is carried out at temperatures 900+ 1300°C, in dependence of the required functional properties. The Faculty of Foundry Engineering together with the Faculty of Material Engineering and Ceramics developed the technology of production of burned ceramic materials with using spent moulding and core sands. The mentioned above waste materials of the foundry industry fulfilled -in plastic masses intended for obtaining ceramic materials -the role of the addition weakening clay raw materials. The laboratory investigations were fully verified by the results of industrial tests. It should be pointed out that none negative effects were observed at the stage of mixing raw materials and preparation of plastic masses. The measurements of exhaust gases emissions performed during burning the products containing spent moulding sands as well as during the normal production did not exhibit any significant differences, which could have indicated the harmful impact on the natural environment.IntroductionSands are used by the foundry industry to make metal casting molds and are a mixture of silica sand, bentonite clay and carbonaceous additives or resins. During the casting process, the molten metal cause thermal decomposition of carbonaceous additives or resins, which results in the formation of potentially hazardous organics, that are emitted to the atmosphere and condense in the molding sand. Each year the U.S. foundry industry landfills about 10 million tones of sand because it is no longer suitable to make metal casting molds. A large high-silica sand content in spent foundry sands (SFSs) generates rational premises for their reuse in other than foundry practice fields. Efforts to divert the SFSs from landfills and encourage their beneficial use in manufactured soils, geotechnical applications, the construction industry (road construction, highway construction), the building materials industry (cement, bricks, limestone manufacture), in the filling of mining cavities or in landfill construction (roads on landfills, permanent covers) are make [1-7]."

Jan 1, 2013

By Joon H. Jang

At a selected pH, hydrothermal oxidation of chalcopyrite was carried out under controlled F+,, at elevated pressures and temperatures (172-200°C) by balancing the rate of oxygen injection against the rate of consumption. Chalcopyrite was converted to covellite (CuS) and digenite (CU1.8S) with rejection of iron and sulfur to the solution. Covellite forms in the first stage, followed by nucleation and growth of digenite in the second stage. The effects of rapid and slow injection of stoichiometric quantities of oxygen are compared. Both the covellite and digenite form a porous layer occupying the same volume as the original chalcopyrite grain. An electrochemical kinetic model is presented to correlate the observed results.

Jan 1, 1993

By Christoph Pichler

A special desulphurization slag accrues during the processing of iron ore to steel, which is needed to generate high quality steel. Sulphur removing is done by different technologies, but the most common one is the generation of a high sulphur containing slag by sulphur affine elements. Currently, this desulphurization slag is partly recycled, however, huge amounts are still dumped. To utilize this desulphurization slag for future purposes, a recycling process must be established. Therefore, first characterization of this material started some years ago at the Chair of Nonferrous Metallurgy, Montanuniversität Leoben. Subsequent trials in lab scale size were performed, also some investigations for different treatment steps were evaluated, starting with a parameter study in a hot stage microscope at various gas-atmospheres. Finally, the developed recycling process concept was verified in pilot scale trials to confirm the new recycling technology. Due to the successful treatment process, also a patent was applied.

By Guohua Bai, Yuanbo Zhang, Guihong Han, Zijian Su, Daoyuan Zhang

"Specularite ores have poor hydrophilicity and ballability as well as inferior high-temperature reactivity, which restrict the large-scale application of them in the pelletizing and sintering production. Modified humic acid (MHA) organic binders are firstly used for pellet preparation from specularite in this paper. The results show that the drop strength of green pellets is 3.7 times/0.5m and compression strength is 12.5 N/P by using 1.0 wt% MHA as binder. Under the optimal experimental conditions of preheating temperature 980 °C, preheating time 12 min, roasting temperature 1280 °C and roasting time 10 min, the preheated pellets have the compression strength more than 400 N/P, and that of roasted pellets is 2747 N/P. The strength of finished pellets meets the requirements of blast furnace iron-making. MHA is a kind of more effective organic binder for specularite pellets compared with the inorganic bentonite.IntroductionAcid Pellets have advantages of good strength, uniformity particle size, high iron grade and good reducibility, which can be used as high-quality burdens for blast furnaces [1]. With fast development of Chinese iron and steel industry domestic magnetite concentrates with high grade of iron and good firing performances become shortage.Imported specularite ores have advantages of low price and high grade of iron (generally above 67 wt%), so the application of them in pellets is an effective way for sustainable development of pellet industry in China. However, the specularites have not been utilized in pelletizing and sintering at present because of the poor ballability and high-temperature reactivity [2, 3]. Most of the pellet plants use bentonite as binders, the amount of which is about 2~3 wt%. The pellet production practice shows that 90 wt% bentonite is still residual in finished pellets and reduces the iron grade [3]. Developing a new organic binder instead of bentonite is very important to the high-quality pellet production. On one hand, the consumption of bentonite is obviously reduced, resulting in decreasing the ironmaking coke ratio and slag discharge; On the other hand, the iron grade of finished pellets are improved, which brings the benefit for the ironmaking production."

Jan 1, 2011

By Dong Liang, Qijie Zhai, Zhichen Zhang, Qixin Li, Zhishuai Xu

"The formation, distribution and survival of pure Al nuclei under surface pulsed magneto oscillation (SPMO) treatment were investigated with thecombination of experiments and numerical simulation. The results indicated that the nuclei originated from the whole top surface of melt owing to the oscillation of top surface induced by SPMO. The temperature field significantly affected the survival of the nuclei The electromagnetic force and flow field of the melt with SPMO treatment were simulated by finite element software ANSYS. The electromagnetic force mainly distributed below the top surface near the mould wall. The electromagnetic farce not only made the melt oscillate but also increased the convection of meh below the top surface vigorously. The oscillation near the top surface of the melt promoted the nucleation largely, and the convection increased the uniform of the temperature distribution in the whole meh which favored the survival of nucleiIntroductionAs we all know, fine equiaxed grains are beneficial fur the improvement of the mechanical property, process ability and the uniformity of metallic materials [1-2]. With the researches of recent decades, people discovered that the electromagnetic field is an efficient method to refine the solidified structure of metals [3-7]. Pulsed magnetic field technology obtains more and more attentions in recent years due to its smaller power consumption, bigger instantaneous magnetic field intensity, non-contacting with the meh and simple convenient equipment manufacturing [8-9]. However, the melts would splash fiercely when pulsed magnetic field is applied with a slightly higher power. Thus, based on the understanding of the solidification refinement mechanism of electric current pulse (ECP) [10], Gong et al [11] developed a novel technology called pulse magneto-oscillation (PMO) to refine the solidification structure. The technology can be easily applied in the solidification structure refinement of continuous casting slab. But fur aluminum continuous casting, the sump is very shallow, which greatly limits the application of pulse magneto-oscillation technology."

Jan 1, 2014

By Anxiang Wang, Kunhua Wu, Yifu Li, Junjie Xu, Yongnian Dai, Bin Yang, Lingxin Kong

In this study, the saturated vapor pressures of tin (Sn) and antimony (Sb), the separation coefficient and the vapor-liquid phase equilibrium of Sn-Sb alloy were theoretically analyzed, which demonstrate that it is possible to separate Sn and Sb by vacuum distillation. The process parameters of vacuum distillation, including the distillation temperature, distillation time and alloy mass (thickness of raw materials) on the direct yield of Sn and the content of Sn in liquid phase were investigated by using single factor experiments. The preliminary results show that the direct yield and the content of Sn are 98.77 wt.% and 96.01% with the optimized distillation conditions of a distillation temperature of 1473 K, a distillation t ime for 45 min and a Sn-Sb alloy mass of 125 g ( thickness o f 8 mm). The distillation parameters in the study provide effective and convenient conditions on separation of Sn-Sb alloy.

Jan 1, 2016

By Yuzura Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about I 880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties 'such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

By Roland Loewen

A review of the aqua regia method for the recovery of gold from jewelry shop wastes is given. Also outlined is a specialized procedure for the recovery of the silver that occurs in these wastes. A classic method for the recovery of platinum and palladium is, given. There is a brief review of other gold and silver refining methods. Environmental conditions are discussed and a few perhaps, new and useful processes ,are mentioned. References are by author or editor and are listed alphabetically. Suggestions for further information in the field of precious metals, are given in a final list.

Jan 1, 1989

By Young-Chul Kang

The Onsan Copper Smelter of LG-Nikko Copper Inc. is a unique plant, which has been operating two smelting processes since 1998. The operation of the first one was started in 1979 with a capacity of 80,000tpy of copper in concentrates utilizing Outokumpu flash- smelting technology. The other one was started in 1998 based on Mitsubishi continuous process with a capacity of 160,000tpy of copper in concentrates. Through several expansion projects, the total smelting capacity of both processes is expected to reach 430,000tpy of copper in concentrates towards the end of 2002. This article describes operation advantages of having two different processes at one plant and comparative operation results in terms of productivity, impurity distribution, energy consumption and environment issues and etc?

Jan 1, 2003

By M. Tangstad, H. Mølnäs, J. D. Steenkamp

"Temperature affects several aspects of pyrometallurgical systems, including thermodynamics and reaction kinetics. Reliability of temperature measurements in laboratory and plant applications is thus important from process, safety and financial perspectives. This case study briefly introduces different techniques utilized for temperature validation, and demonstrates temperature validation on laboratory scale utilizing the wire-bridge method. Pt/Ptl3Rh thermocouple hot junctions were constructed by mechanically connecting thermocouple wires through a pure metal bridge consisting of copper, gold, nickel or palladium wire. When heating the wire-bridge thermocouple alongside a regular Pt/Ptl3Rh thermocouple, temperature offsets were quantified as the wirebridge thermocouple short-circuited at the melting points of the pure metals. At the melting points of gold (1064°C) and palladium (1555°C), average measured temperature offsets were -2.1°C ± 2.3°C and 0.2°C ± 0.4°C, respectively. Results from the copper and nickel wire-bridges were inconclusive. The paper concludes with a discussion on the potential industrial applications of the technique.IntroductionThermocouples are probably the simplest of all temperature sensors, but are widely utilized due to simplicity, versatility and ability to handle a variety of experimental conditions and industrial applications. Additionally, thermocouples are often the only option in research laboratories requiring high temperature measurements, and a high level of reliability is usually required from thermodynamic, kinetic as well as safety points of view.The study presented here originated from a test program where the compatibility between different types of carbon-based refractory materials and industrial slag produced in silicomanganese furnaces were investigated on a laboratory scale utilizing the static crucible test[l]. Due to the nature of the silicomanganese production process, the compatibility tests were to be conducted at 1600CC[2]. Details of the experimental set-up utilized for the compatibility tests are discussed in the Experimental Set-up and Method Statement section later in this paper."

Jan 1, 2012

By K. S. Han, M. Yoshimuura, H. Fujita, Y. Sato, S. W. Song

"Film of LlCoO2 as cathode material for rechargeable lithium microbatteries has been fabricated on the platinum metal substrate by electrochemical-hydrothermal method in concentrated LiOH solution at 200 °C as Soft Solution-Processing. The film fabrication has been understood in terms of dissolution of cobalt metal powders and subsequent oxidative deposition on the substrate. The film structure was characterized using scanning electron microscope, X-ray diffraction analysis; X-ray photoelectron spectroscopy and micro-Raman spectroscopy.IntroductionRapid growth of wireless communications and emerging integrated optoelectronic circuits caused the miniaturization· cif electronic devices, thus the demand for high energy density microbatteries as a power source for the microelectronics increases. In this regard, all solid-state lithium microbatteries including LiCoO2 and LlMn2O 4 [l-4], the most promising intercalation cathode material, have been developed. However, major difficulty of .fabrication of a lithium microbattery arose from the preparation of cathode film, according to a· recent report on Rare Metal News [5]. Although many attempts have been made to deposit the cathode films, all those methods are mostly chemical vapor deposiiton (CVD), various evaporation, sputtering techniques and spray pyrolysis. These methods require preparation of bulk cathode materials cir its precursor, then deposition with complicated instruments including high· vacuum system, and even postsynthesis annealing to obtain desire electrochemical 'properties. It is clear that all of these techniques are neither economic nor environmentally friendly. Compared to those methods, film form.ation from an aqueous solution is thought to be simpler and more economical, and requires much· less energy consumption. Our .group has demonstrated the utility of Soft SolutionProcessing [6,7], which is defined as environmentally friendly processing using (aqueous) solutions, to produce films of a variety of functional solid materials. According to the Pourvaix's diagram [8], some metal can be dissolved in an alkaline solution and consequently combined with hydroxyl group or oxygen anion forming metalate or metalite. Cobalt also seemed to form cobaltite, HCoOi in strong alkaline solution in the Pourvaix's pH-potential diagram. Based on this information, it was expected that LiCoO2 could be prepared using the cobalt metal in Li OH solution by Soft Solution-Processing. Recently, we reported the successful single step fabrication of electrochemically active LlCoO2 films on the cobalt metal substrate by hydrothermal methods without any post-synthesis annealing as Soft SolutionProcessing [9,10]. Film formation mechanism could be elucidated by the following evidences. . As expected from Pourvaix's diagram, cobalt metal was dissolved in concentrated LiOH solution forming dissolved cobalt species which was detected by an observation of absorption band in UV-VIS absorption spectrum [10]. Thus the reaction was assumed to be started from dissolution. Time dependent potential of Co electrode exhibited only one-step evolution with 0.6 eV from Co metal to LiCoO2 [10]. Another strong evidence was the finding of LiCoO2 powder precipitates at the bottom of tetlon beaker after the reaction [11]. Based on those experimental findings, it was understood that film is formed by dissolution-precipitation mechanism [9-11]."

Jan 1, 2000

By Jorge Alberto Soares Tenório, Flávia Paulucci Cianga Silvas, Denise Crocce Romano Espinosa, Ivo André Homrich Schneider, Erika Gusmão, Daniella Cardoso Buzzi, José Roberto de Oliveira

"This study evaluated the Salvinia sp action on metals biosorption in a synthetic sample of acid mine drainage (AMD) in order to determine the time and amount of metals uptake. Biosorptives tests were realized varying the contact time of 5, 20, 60 and 240 minutes. And keeping constant the follow parameters: pH (2.6), biomass concentration (1g.L-1), temperature (25°C) and agitation (175rpm). In order to quantify the metals concentration captured by biomass, the AMD samples will be analyzed by ICP. Biosorbent, Salvinia sp., will be characterized before and after the biosorptives tests through analysis of SEM and IR. The micrographs indicate the occurrence of micro-precipitation and changes in biomass physical structure. The infrared spectra indicate changes in functional groups present in the biomass before and after the biosorptives tests.IntroductionThe current emphasis on environmental sustainability leads the industry in general, to treat their waste. The human activities are increasing, highlighting the industrial and mining activities, and have promoted the contamination of soil, waterways and groundwater by metals (1). The waste must undergo treatment processes aimed at reducing pollution, and therefore, less aggression ecosystems.This means the importance of studies of economic and effective methods to eliminate these metals from wastewater generated. The bioindicators are good investments in this area. The aquatic weeds are plants that inhabit swamps up from truly aquatic environments. They have several morphological and physiological adaptations that enable them to colonize the various aquatic environments. They are used as bioindicators of water quality and have also been used in decontamination of aquatic environments, production of biomass for livestock feed, fertilizers, soil and fish tanks (2)."

Jan 1, 2012

By Guo Chen, Jin Chen, Jinhui Peng

"In this paper, the methods of life cycle assessment for microwave hot air systems, and the concept of green degree were proposed. Greenness evaluation index, evaluation system and evaluation model of microwave hot air systems were established. Also, life cycle assessment processing based on these ideas was introduced. Analytic hierarchy process and fuzzy decision- making method were utilized to establish and solve the greenness evaluation of assessment model, while the scores of green degree in microwave hot air systems were obtained. The results show that Life cycle assessment can be applied effectively and efficiently to the microwave hot air systems.IntroductionHot air systems are an important industrial operation condition, which is used to provide high temperature air for materials processing. Nowadays, high temperature airs are manufactured by the conventional heating processes, in which some ceramic materials are used as heating materials. However, these processes pollute the environment. Therefore, to explore new method to produce high temperature air with low energy consumption and less environment pollution are necessary.Microwaves are now being used in various technological and scientific fields in order to heat dielectric materials [1]. Microwaves irradiation has been explored in materials processing in recent years [2-3]. The main advantage of using microwave heating is that the treatment time can be considerably reduced, which in many cases represents a reduction in the energy consumption as well. Since there is energy absorption but no heat conduction, the heating is very rapid and highly efficient, resulting in energy savings and the shortened processing time [2, 4]. Compared with conventional heating techniques, the additional advantage of using microwave irradiation is that microwave irradiation achieves both internal and uniform heating [5-7]. In addition, it is more convenient to control the microwave irradiation processing, because of no direct contact between the heating source and heated materials with less equipment size and waste [2, 8-9]. Life cycle assessment is used and accepted methods for the evaluation of the environmental impacts of products or systems [10]. Recently, many appropriate evaluation methods have been developed for life cycle assessment [11-12]. These proposed methods usually are employed for the evaluating product and analyzing results [13]. Among them, the analytic hierarchy process and the fuzzy comprehensive evaluation stand out as a popular method utilized in many fields [14-16]. Analytic hierarchy process and fuzzy comprehensive evaluation are a combination of mathematical and statistical technique that is useful for analyzing the effects of several independent assessment aspects on the system goal without the need of the predetermined relationship between the objective function and the assessment aspects [17-19]."

Jan 1, 2013

By Bin Xu, Qian Li, Yong-bin Yang, Xiao-liang Liu, Tao Jiang, Yan Zhang

Some high sulfur and arsenic-bearing gold concentrate has a gold leaching rate less than 80% by oxidation roasting-pickling-cyanidation process. The characteristics and intensification of gold leaching were studied systemically. By combining chemical composition and phase analysis, the low gold leaching rate was found to lie in the capsulation of gold by iron-containing phases including iron oxides, arsenopyrite and pyrite. 96.66% of gold in the industrial leaching residue was capsulated and 95.88% of the capsulated turned out to be in the iron-containing phases. The results of laboratory pickling-cyanidation experiments on the calcine and industrial leaching residue presented further demonstration for the fact that gold capsulated in the iron-containing phases was hard to be leached. However, the gold cyanide leaching rate of calcine could be raised over 95% by a reduction roasting-pickling pretreatment which played such a significant role in exposing the capsulated gold that gold leaching was intensified remarkably.

Jan 1, 2015

By Samantha Moodley, Rauf Hurman Eric, Cevat Kucukkaragoz, Aditya Kale

"Two titania slags, rutile and synthetic rutile were chlorinated with petroleum coke and CO in a small bubbling fluidized bed reactor. The study aims to identify differences in chlorination mechanism, compare conversion rates, blowover and the chlorination of impurities for the various titania feedstocks at different temperatures.Chlorination rates were highest at 1000ºC; rutile chlorination significantly increases as temperature increases from 800ºC to 1000ºC. At 1000ºC, synthetic rutile had the highest chlorination conversion rate; this was followed by Slag B which in turn was more reactive than Slag A and rutile. The mechanism for slag, synthetic rutile (SR) and rutile chlorination differs. Synthetic rutile feed is porous, providing a larger surface area for the chlorination reaction, hence the highest conversion rates was attained. Titania slag becomes porous with the initial chlorination of FeO and MnO whilst rutile remains solid. As the porosity of slag particles increases so does its tendency to be elutriated. Ti2O3 is oxidized within the early stages of chlorination during the chlorination of FeO and MnO. Ti2O3 not oxidized is then rapidly chlorinated.IntroductionTitanium dioxide (TiO2) is the most common compound of titanium, about 95 - 98% of extracted titanium minerals is processed into TiO2 white pigment [1]. Two processing routes exist for the production of TiO2 pigments, i.e., sulphate and chloride based processes. In the chloride process, titania feedstock is fed to a fluidized bed reactor together with reductant and chlorine gas. A temperature of 1000 - 1300ºC is maintained in the reaction zone and apart from silica, zirconia, uranium and thorium, virtually all the metal oxides in the feed are converted to their respective chlorides [2]. Chlorine is recovered and recycled back to the reactor."

Jan 1, 2012

Numerical simulation of the fluid flow and heat transfer has been carried out for a waste-heat boiler in an Outokumpu type copper flash smelter. In this boiler, SO2-containing off-gas flows into the waste-heat boiler radiation section at about 1350°C. A fraction of cooler off-gas from the electrostatic precipitator at about 200°C was recirculated into the radiation section, and a small amount of ambient air was leaked into the boiler from the bottom. The computational results show that the flow is strongly recirculating and distinctly three dimensional in most of the boiler, particularly in the radiation section. The hot off-gas cooled down rapidly after entering the radiation section due to radiation. The predicted flow pattern and temperature distribution were in a good agreement with laboratory models and industrial measurements.

Jan 1, 1995

By Qingyu Deng, Shiwei Ma, Guibao Qiu, Hua Wang

"The flow behavior of the blast furnace slag bearing titanium, like viscosity, play an importance role during the iron-making process with the vanadium-titanium magnetite, which is a very special minerals in Panzhihua, China. The dependency of the viscosity on the chemical composition like TiO2, Al2O3, MgO, binary basicity (CaO/SiO2), temperature, reaction time were studied. The experiments showed that the viscosity decreased with the increase of TiO2, MgO content and binary basicity, and it increased with the increase of Al2O3 content and temperature. The viscosity showed a slight decrease within 60mins’ reaction with graphite crucible, however, it increased rapidly afterwards with the formation of Ti(C, N).IntroductionThe ordinary iron ore has been an essential part of raw materials for vanadium-titanium magnetite smelting in Panzhihua to avoid a series of problems, such as slag thickening, adhesive bond of slag and hot metal, etc. The ratio of vanadium-titanium magnetite has been decreased gradually since 1970s, and has down to about 65% now. However, with the substantial appreciation of price of imported ordinary iron ore, Panzhihua Iron and Steel Group aims to increase the ratio of vanadium-titanium magnetite and decrease the dependence on ordinary iron ore in order to lower the cost of smelting process."

Jan 1, 2012

By Kliment Y. Hakobyan

A new technology for treating molybdenum sulfide concentrates has been developed. It includes roasting the concentrate in a special regime with water vapor, cooling and neutralizing exit gas, oxidation roasting of rhenium containing MoO2, and the extraction of rhenium from exit gases. This technology allows economically efficient and environmentally safe processing of molybdenum concentrates: The degree of molybdenum extraction is 98.8%, rhenium-90%, sulphur-98.4%. The technology also ensures high extents of extraction of selenium and tellurium as well as the fixation of sulfur in the form of sodium sulfide or elemental sulfur.

Jan 1, 2006

By Tapio Ahokainen

Commercial modeling software and increasingly efficient computers enable today computational fluid dynamics (CFD) to be used as a tool for a more comprehensive understanding of the flash smelting and flash converting processes. CFD modeling can be used for design purposes in many technological areas, but some relevant physical and chemical phenomena are still missing in the commercial CFD solver packages. Therefore, Outokumpu has developed several subroutines for solvers to describe analytically the phenomena in the flash smelting environment. CFD sub-models of the copper concentrate and matte combustion, the particle-particle-wall interactions and for more accurate radiation properties of the gas-particle suspension are needed to ensure reliability of numerical simulations on the flash smelting and converting vessels. Several basic combustion phenomena can be modeled with a number of commercial solver packages, but own models for combustion must be included in the case of sulfides as the feed. Mathematical models for copper concentrate and solid matte combustion have been developed during the last decade. They calculate compositions of the particles and temperature, based on extensive experimental research work in laboratory scale furnaces with validated kinetic parameters and temperature measurements of reacting particles. Inside and near the concentrate burner, the standard particle tracking methods do not include the particle-particle interactions and the particle-wall interaction is too much simplified to describe properly the particle collisions with the distribution cone. Therefore, additional models for the particle-particle as well as particle-wall interactions have been written and implemented. For thermal radiation, models for the emissivity of a gas mixture and for calculating the particle absorption and scattering coefficients have been developed and tested. In addition, the advanced radiation model can be used i.e. in the enhanced simulation of off-gas cooling in the heat recovery boiler area of the flash smelter.

Jan 1, 2006