Search Documents

By Lightfoot. Nicholas, Na Liu

"Mining in multi-seam workings has been undertaken for many years in the VK Remnant pillars above and/or below current working areas have an important influence on retreat gateroad conditions at five of the remaining six deep coal mines. These interaction effects need lo be predicted ahead of mining so that longwall panels can be positioned to minimize roadway damage and to identify areas where additional support should be installed early into competent strata when and where it is most effective.Currently, three-dimensional elastic stress analysis using MAP3D is undertaken to predict local vertical and horizontal stress magnitudes during gateroad development and in front of the face on retreat. The predicted stress fields are often used as input to FLAC for roadway modelling.Using Maltby Colliery in South Yorkshire as a case study, this paper illustrates the MAP3D approach, together with its current limitations and uncertainties. Possible future improvements in the analysis method are proposed and the authors would welcome comments on these, or suggestions for alternative approaches.MODELLING OF MULTl-SEAM LAYOUT & MULTI-SEAM INTERACTIONThe remaining large coal mines in the UK arc operating at depths of 800-1, 150 m (2,625-3,773 ft). Production panels are now mined on retreat after the accompanying single entry access roadways have been completed. These gateroads are typically supported with a system of steel rock bolts and cable in the roof and steel bolts and glass re in forced polymer (G RP) dowels in the sidewalls.In addition to new panels being mined in the vicinity of old goafed districts, a significant amount of extraction has usually already taken place in coal seams above and/or below the current working areas. This means that there is also interaction between the current workings and the remnants of the old workings in other seams. As a consequence of the mining methods employed, old workings can have a complex geometry compri ing collapsed and partially collapsed excavations intersper ed with small and large pillars of unmined coal. The unmined coal pillar act as stress concentrators that carry the overburden load while the mined out excavations create stress shadows of varying degrees depending on how much collap e and reconsolidat ion has occurred. This is illustrated by a simple elastic model as shown in Figure I."

Jan 1, 2010

By Frank E. Chase

Sacrificial entries, roof slotting, and other tactics have been used to combat high horizontal stresses during roadway development in U.S. coal mines. In Australia, the "pillar extraction on the advance" mining method has been successfully employed as a horizontal stress control technique. The concept of advancing and relieving mine workings through pillar extraction developed from observations that some mines experience difficult ground conditions when advancing and retreating the first panel in a new reserve. However, conditions dramatically improve in subsequent panels. Apparently, the creation of a gob area stress relieves the adjacent panel workings. After much debate and close scrutiny, the first U.S. roof control plan to advance and relieve was approved in 1998, for the Sargent Hollow Mine in Wise County, VA. The major concern was that this mining practice places section personnel inby of the gob. The tentative approval permitted barrier pillar slabbing and removal of the adjacent development pillar during panel development. The intent of the plan was to provide a "stress shadow" for the advancing faces and outby workings to reduce the excessive number of roof falls. Sargent Hollow successfully extracted their first panel by pillaring on advance and retreat mining using posts. Mobile roof supports were employed to extract pillars while advancing the second panel. This paper summarizes Sargent Hollow Mine's experiences with the advance and relieve mining method.

Jan 1, 1999

By X. L. Yao

This paper analyses the effects of mining extraction geometry (width/depth ratio) and dip of seam on subsidence parameters based on a large Database, containing 120 longwall mining cases all within the UK coalfields. The subsidence parameters evaluated in this paper include the following: the maximum subsidence value with different goaf-treatments, the position of maximum subsidence, the position of half-subsidence, subsidence value over the rib-side, positions of maximum tensile strains, positions of inflection points and the magnitude of maximum tensile strains on both rise and dip sides. Additionally, the maximum compressive strain and two limit angles are also studied in this paper. Based on a comprehensive Database analysis, several equations are derived relating these parameters to the width/depth ratio and the dip of seam. The results should assist engineers to design new structures, or take measures to protect existing structures from strain effects. The findings of the research assist in extension of the SEH to inclined seams with greater certainty.

Jan 1, 1990

By Tom Blevins, Roland Walker, Jinsheng Chen

"The Dywidag-Systems International DSI Tandem Anchor bolt, with an improved expansion shell-washer design, can substantially reduce potential entry roof falls caused by twisted or deformed expansion shells of the traditional mechanical anchor bolts during installation. In addition, the improved anchorage system can also ensure that a consistent and high installed load is achieved, which is critical for effective beam building under thinly laminated or layered roof conditions. This paper discusses the genesis and anchorage performance of the Tandem Anchor bolt, and analyzes the tension/torque relationship of different mechanical shell anchors using data obtained from both lab and field tests. It also discusses roof bolting mechanisms, roof bolting systems, and factors influencing effective beam building. Finally, numerical modeling was used to analyze the effect of bolt pretension magnitude on entry roof stability.INTRODUCTIONThroughout the history of underground mining, keeping the roof from uncontrollable collapse has been the greatest concern of the miner. Tremendous strides have been made in better understanding, predicting, and supporting the mine roof. This conference has spent the last twenty-eight years sharing information and distributing it to the mining community. A paraphrased statement from former Secretary of Defense Donald Rumsfeld adequately describes the challenges to the mining engineer as it pertains to roof control: it is a study of known knowns, known unknowns, and unknown unknowns. It is the hope of the authors to address some of these unknowns.The paper discusses the development of bolt anchorage systems from dry shells to shells with resin-assisted anchorage. It looks at some of the issues faced with the anchorage shells being used when introducing the insertion pressures caused by resin cartridges. The rationale behind the shell design changes was to compensate for this resin induced stresses.An improved expansion shell assembly (a slotted expansion shell base, a tapered cramming plug, and a novel support nut with tapered top) for mine roof bolts makes up the Tandem Anchor (U.S. Pat. No. 6742966); this minimizes the possibility of twisting seen with traditional mechanical shells and thus prevents springy bolts and shell leaves from breaking. A fully grouted Tandem Anchor bolting system has the advantages of both the pure mechanical point-anchor and the non-pretention fully grouted bolting systems. Once installed, the installed load or pretension will be locked in and never bleed off. Compared with the fully-grouted (2-speed resin) tension rebar bolting system, the fully-grouted Tandem Anchor bolting system can (a) reduce bolting cycle time (about 15 seconds per bolt), boosting coal production and productivity; (b) provide a greater installed load or pretention; and (c) achieve a consistent tension/torque ratio, which gives better bolting quality control. Therefore, a fully grouted Tandem Anchor bolting system is the most effective means to reinforce a weak rock mass intrinsically by the theory of beam building. For thinly laminated or layered roof conditions, a higher installed load or pretention (50% or more of the bolt's yield strength) can make a roof bolting system much stiffer, which results in less roof movement. Numerical modeling results show that the magnitude of the roof's tensile stress and relaxation zone can be substantially reduced under a higher installed load or pretention."

Jan 1, 2010

By David F. Gearhart, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

"Coal mine longwall gateroads are subject to changing loading conditions induced by the advancing longwall face. The ground response and support requirements are closely related to the magnitude and orientation of the stress changes, as well as the local geology. This paper presents the monitoring results of gateroad response and support performance at two longwall mines at a 600-ft and 2,000-ft depth of cover. At the first mine, a three-entry gateroad layout was used. The second mine used a four-entry, yield-abutment-yield gateroad pillar system. Local ground deformation and support response were monitored at both sites. The monitoring period started during the development stage and continued during first panel retreat and up to second panel retreat. The two data sets were used to compare the response of the entries in two very different geotechnical settings and different gateroad layouts. The monitoring results were used to validate numerical models that simulate the loading conditions and entry response for these widely differing conditions. The validated models were used to compare the load path and ground response at the two mines. This paper demonstrates the potential for numerical models to assist mine engineers in optimizing longwall layouts and gateroad support systems.INTRODUCTIONThe need for roof stability in coal mine longwall gateroads places significant demands on the gateroad ground support system. The variable loading conditions associated with the approaching longwall face can cause excessive ground deformations that need to be accommodated by the support system. In coal mines in the United States several different types of supports are used to maintain the stability of gateroads. The supports may include grouted roof bolts, cable bolts, and roof trusses as intrinsic support. Standing supports include timber cribs, engineered timber props, and various types of cement-based cribs. The intensity of support is governed by the expected geologic conditions and the expected stress changes that will occur during longwall mining. At present, the design of ground support for gateroads is largely based on local experience. In-mine trials are usually conducted when new support technologies become available or ground conditions dictate a change in the support system. The research reported in this paper has the objective to assist mining engineers in evaluating alternative gateroad supports and to design suitable support systems for the local ground conditions."

Jan 1, 2018

By Ihsan Berk Tulu

The complex interaction between multiple seam pillar extraction panels and variable topography can generate unexpected ground control problems. This case study describes stress-related damage in multiple seam workings that resulted in difficult operating conditions and compromised the safety of the support crews. The damage appeared to be caused by horizontal stress but the unexpected location of the damage baffled the authors. A 2D Finite element analysis was conducted of the mine layout and surface topography in an attempt to explain the observed failure. It was discovered that the topography resulted in the rotation of the major stress at the location of the current workings. The stress rotation caused asymmetrical interactions between the workings on the different coal beds, which can explain the unexpected response observed in the mine. Consequently the layout of the next panel was changed by locating the vulnerable entry 30 ft away from its originally planned position. The new location was selected to locate the entry in favorable stress conditions. The change in layout resulted in a significant improvement in conditions when the next panel was mined. At the time of writing this paper, a full panel has been developed using the modified layout without undue ground control problems. The case study demonstrates that numerical models can help engineers to interpret and solve complex multi-seam interaction problems.

Jan 1, 2014

By Bo-Hyun Kim, Mark K. Larson

"While faults are commonly simulated as a single planar or non-planar interface for a safety or stability analysis in underground mining excavation, the real 3D structure of a fault is often very complex with different branches that reactivate at different times. Furthermore, these branches are zones of non-zero thickness where material continuously undergoes damage even during interseismic periods. In this study, the initiation and the initial evolution of a strike-slip fault was modeled using the FLAC3D™ software program. The initial and boundary conditions are simplified and mimic the Riedel shear experiment and the constitutive model in the literature. The FLAC3D model successfully replicates and creates the 3D fault zone as a strike-slip type structure in the entire thickness of the model. The strike-slip fault structure and normal displacement result in the formation of valleys in the model. Three panels of a longwall excavation are virtually placed and excavated beneath a main valley. The characteristics of stored and dissipated energy associated with the panel excavations are examined and observed at different stages of shear strain in the fault to evaluate bump potential. Depending on the shear strain in the fault, the energy characteristics adjacent to the longwall panels present different degrees of bump potential, which is not possible to capture by conventional fault simulation using an interface.INTRODUCTIONThis paper is part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bump-prone potential in highly stressed ground conditions. More specifically, this paper reports an exploratory effort with an unconventional approach using a numerical tool to try to better understand a possible scenario where bump risk might be increased—that is, a scenario involving a strike-slip fault. The objective is to assess whether a numerical tool might be useful or practical in forecasting bump potential associated with a strike-slip fault for a typical, structural geologic setting."

Jan 1, 2018

By George S. Kalamaras

Coal strata strength is included as a vague term in most of the pillar design formulas, either as a questionable fraction of the intact coal strength or a size-dependent relationship for scaling down a laboratory value to the in situ strength. In order to introduce a coal mass strength criterion which would be compatible with current design trends, the Rock Mass Rating (RMR) system was revised to incorporate factors governing coal seam behavior under load. A number of adjustment factors have been proposed but, the most significant change, is the introduction of a parameter representing the heterogeneity of the seam. When developing a rock mass strength criterion, it is necessary to find the constants of appropriate intact rock strength criteria and to establish a correlation to scale down these constants as a function of the RMR. For four intact rock strength criteria, the constants for coal were found using the Nelder-Mead method. To correlate the constants of the strength criteria with the coal seam quality values (RMR), a procedure was developed based on finite element modeling of in situ large scale tests for which the RMR was known. A new coal strata strength criterion is proposed, in a principal stress formulation, for modeling coal pillar behavior when the stress field in a pillar is known. A linear relationship is also given, to be used when empirical pillar strength formulas are used to design pillars. The proposed criteria have been evaluated in a case study.

Jan 1, 1993

By John G. Oldsen

Passive cable bolting and active cable trusses have been used in roof support for more than two years Excellent roof control has been experienced by many coal operations. This paper covers the new and innovative developments in cable support systems and their application in mines. Multiple cable bolts, tensioned cable bolts, coal rib wrapping, and other cable applications will be covered.

Jan 1, 1997

By Bruce K. Hebblewhit

Australia is well endowed with extensive reserves of thick underground coal scams, particularly in the range of 4.5m to 9m thicknesses. (For the purposes of this paper, thick scams are defined as being greater than 4.5m thick.) At the present time, the thickest, high production, high productivity underground mining operation in Australia operates at a maximum of approximately 4.8m using single pass longwall methods. In a number of instances, conventional' height operations are mining thick seam coal, effectively sterilising considerable reserves - either because of financial or technical risk concerns, or in some cases poorer quality coal at some horizons in the scam, UNSW has been involved in thick scam mining research over many years, most recently through an ACARP -funded project, jointly with the CMTE in Australia. A key part of that project involved the assessment of the relative geotechnical risks associated with the various methods under consideration. The methods were: single pass longwall; multi-slice descending longwall; soutirage and related caving methods (including the Chinese Longwall Top Coal Caving method (LTCC)): and hydraulic mining. A formal risk assessment process was adopted to review the risks, relative to a conventional 4m high longwall operation. This paper presents the findings of that risk review and discusses the geotechnical issues (and some possible solutions for risk management) which need to be dealt with in order to bring these methods to fruition in the context of the Australian coal industry environment.

Jan 1, 2001

By John L. Edwards

The underground coal mines in the Lake Macquarie area of the Newcastle Coalfield, New South Wales, Australia are constrained by surface subsidence restrictions as low as 150 mm. The mining environment is shallow, generally between 100 m and 200 m, often multi-seam and commonly overlain by residential development or tidal waters. Most mines use partial or panel and pillar extraction techniques to meet the subsidence restrictions and allow maximum resource recovery. This paper gives an overview of the results of a recent two year government funded research project aimed at developing a mechanistic, geomechanically based mine design criteria for subsidence control. Three extraction layouts were monitored in detail to assess the relationship between mining geometry, pillar behaviour and surface subsidence. Pillars at each site were instrumented with stress cells, convergence monitors and extensometers. Field data was used to initially calibrate, and subsequently, verify stress and displacement predictions made by the three-dimensional displacement discontinuity code, SUBSOL. Back-analysis of the modelling results indicate SUBSOL's capability as a tool to satisfactorily predict surface subsidence magnitudes and pillar loads for alternative pillar and panel layouts.

Jan 1, 1993

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By Xingkai Wang, Wenbing Xie

"To control the large deformation of soft rock around the roadway subjected to high stress, it is important to improve the stability of support structure, in addition to increasing support strength. In this study, the causes for the destabilization of U-steel frame and its loading characteristics were analyzed by theoretical analysis, laboratory experiments and field tests. The technology of constant support resistance, the principle of support structure compensation and the compensation technique are proposed. The results indicated that the main reasons for frame structure destabilization are caused by low strength of connector, irrational structure of connector, poor interaction between the surrounding rocks and support frame and structure, and unstable support structure. Thus, the corresponding technological measures, such as connector with high strength and rational structure are adopted. The bearing capacity of frame is unstable after slipping. In order to maintain the high support resistance when the frame is performing the support function, the frame connector should be retightened after slipping. Though the working resistance may be improved greatly by using the backfilling or back grouting of U-steel, the frame remains unstable because of the unstable frame structure. Therefore, according to the deformation characteristics of rocks surrounding the roadway and the structure instability of U- steel frame, the stable structure device is used to carry out the structural compensation of U-steel frame, and the whole bearing capacity of the frame and its structural stability are improved greatly.INTRODUCTIONThroughout the development of the roadway supports for coal mines in China, it can be seen that the supporting strength and supporting resistance increase continuously with increase in mining depth and supporting difficulties [1]. With respect to the ground control mechanism and supporting technology of rocks surrounding the soft rock roadways subjected to high stress, considerable research has been done both at home and abroad. The backfilling technology behind the high-resistance and yieldable U-steel wall, the new type of grout/bolt support technology and the bolting with high-strength mesh support technology were developed, and have been used widely in coal mines with notable economic benefits [2-7]. However, a large number of engineering practices show that in many cases the existing rock control technology of roadway may not control the large deformation of the soft rock roadways subjected to high stress. The reason that the large deformation of soft rock roadway occurs is mainly due to poor structure stability of existing frame bearing structure, not insufficient support strength."

Jan 1, 2015

By Pierre-Yves Declercq, Andre Vervoort

"After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—an upward movement. Although most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method, surface movement still occurs many decades after mining is terminated. After the closure and flooding of underground excavations and surrounding rock, this movement is reversed. This paper focuses on quantifying the upward movement in two neighboring coal mines (Winterslag and Zwartberg, Belgium). The study is based on data from a remote sensing technique: interferometry with synthetic aperture radar (INSAR). The results of the study show that the rate of upward movement in the decade after closure is about 10 mm/year on average. The upward movements are not linked directly to the past exploitation directly underneath a location. The amounts of subsidence at specific locations are linked mainly to their positions relative to an inverse trough shape situated over the entire mined-out areas and their immediate surroundings. Local features, such as geological faults, can have a secondary effect on the local variation of the uplift. The processes of subsidence and uplift are based on completely different mechanisms. Subsidence is initiated by a caving process, while the process of uplift is clearly linked to flooding. INTRODUCTION After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—upward movement in the area above the past exploitation and in the immediate surroundings. Of course, most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method (Peng, 1986). This downward movement continues to occur at a smaller rate many decades after mining has been terminated when the water in the underground excavations is pumped to the surface. This is the case as long as a mine is in operation. However, after the closure and flooding of the underground excavations and the surrounding rock, this movement is reversed, and the surface is uplifted. A total uplift of about half a meter has been recorded to date. This phenomenon has been described in several different coal basins in Europe, for example, in Belgium (Devleeschouwer et al., 2008), France (Samsonov, d’Oreye, and Smets, 2013), Germany (Baglikow, 2011), the Netherlands (Caro Cuenca, Hooper, and Hanssen, 2013), and Poland (Preusse, Kateloe, and Sroka, 2013). To date, research has focused mainly on understanding the phenomenon (e.g., Herrero et al., 2012) and identifying general trends, whereby the link with the rise in water levels is an important issue (Caro Cuenca, Hooper, and Hanssen, 2013). The most accepted explanation is linked to the swelling of clay minerals in the argillaceous rocks in the coal strata (Herrero et al., 2012). Without doubt, the full explanation is complex, and swelling is probably not the only cause of the residual movement. Most coal strata rock is weakened upon contact with water. The increase in water pressure also results in a decrease in the effective stress. Both aspects facilitate the fracturing of rock, which normally would result in further subsidence. However, decreases in the effective stresses also result in the relaxation or expansion of the rock, which induces an upward movement (Fjar et al., 2008). All of these aspects, including the long-term residual subsidence due to compaction under dry conditions, result in a net upward movement. The phenomenon discussed here is clearly different from the upsidence, sometimes observed on other continents (e.g., in Australia, Galvin, 2016). When upsidence occurs, the rock near the surface bends and buckles upwards due to the overstressing of the floors of the valleys."

Jan 1, 2017

By Adrian L. Moodie

Austar Coal Mine (formerly Southlands and Ellalong Collieries) has had a long association with difficult strata control conditions associated with mining depth and a highly jointed/cleated coal seam. The conditions include poor longwall face conditions, cyclic loading, heavy tailgate (TG) roadway conditions, and difficulties in maintaining stable roadways on development at 5.2 m (17 ft), as well as the geotechnical challenges of an 8.5-m (27.9 ft) -wide roadway required for installation faces. The introduction of Longwall Top Coal Caving (LTCC) to this environment has aided in the management of some of these issues, but LTCC has also given rise to other geotechnical considerations. Additional geotechnical issues associated with LTCC not only require management during operations, but also require consideration when evaluating new mining areas at Austar Coal Mine or potential LTCC extractable resources throughout Australia and the world. In September 2006, LTCC commenced at Austar Coal Mine in longwall panel A1. Since this point the LTCC face has been increased from 147 to 216 m (482 to 709 ft)and finally to 227 m (745 ft) in width, and it has also been rehanded and modified in the three fully extracted panels to date. The application of LTCC in panels A1, A2, A3, and now A4 has been very successful, both from a coal resource recovery point of view and in the management of the principal hazards of spontaneous combustion and strata control. This paper focuses on the geotechnical aspects of the application of LTCC at Austar Coal Mine and also reviews some advances in general strata control management at the mine.

Jan 1, 2011

By Fernando O. L. Xavier

"The Barro Branco coal mine was located in the southern region of Brazil, in the state of Santa Catarina. In 2002, an incident occurred at the mine, leading to a violent, massive pillar failure, resulting in almost 100 failed pillars in less than 3 hours, totaling nearly 700 collapsed pillars after a period of 6 weeks. The paper outlines the geological and operational conditions before the accident and analyzes the primary factors leading up to the event. This paper also discusses and examines the unusual characteristic of violent, uncontrolled pillar bursts that occur over a longer timespan, in comparison to other equally violent but rapid events, such as those that occurred at the Crandall Canyon Mine, at a Book Cliffs District mine, and at the Solvay Mine. INTRODUCTION The southern region of Brazil holds 100% of the coal reserves for the country, and half of it is located within the state of Santa Catarina. Almost the entire Brazil’s coal production, around 8 million tonnes/year, is consumed for electricity generation. Most of the coal mines in Santa Catarina are underground room-and-pillar mines, and most are shallow mines, with depths of cover ranging from 20 to 400 m. The Barro Branco mine, near the city of Criciuma, experienced a violent mine collapse at the end of March 2003, which was analyzed and discussed by Zingano, Koppe, and Costa (2004). The event consisted of violent failure of 100 pillars in less than 3 hours, and a subsequent failure of approximately 700 additional pillars over the next 6 weeks. After the panel collapsed, the mine was closed due to unsafe conditions as a consequence of the seismic event. A map of the collapsed area is shown in Figure 1. GEOLOGY AND MINING METHOD There are two coal seams mined at Barro Branco mine. The first is the 1.5 m to 2.3 m thick Barro Branco Seam, under about 75 m of cover. The second is the Bonito Seam, where the collapse occurred. The Bonito Seam is 2.5 to 5.5 m thick located at a depth of approximately 80 m, with an average dip of 0° to 15°. Various major faults and inherent joints are present in the area."

Jan 1, 2017

By Anthony T. Iannacchione

The Solar No. 7 and Solar No. 10 mines were designed to prevent mine waters from directly discharging to the surface. In January of 2004, a discharge occurred as the Solar No. 7 mine was in its final stage of flooding through a barrier averaging 456-ft in width over a 1,600-ft length (No. 1). Another barrier (No. 2) was designed to protect four municipal water wells operating 1,800- ft away and producing from within or slightly below the Upper Kittanning coalbed from the adjacent Solar No. 7 and No. 10 mine pools. These two barriers were selected for this study because of varied mine layouts, mining methods, and geology factors affecting their performance. Analysis was aided by the collection and georeferencing of 6-month mining maps from the Pennsylvania Department of Environmental Protection (PA DEP). A structure contour map of the Upper Kittanning coalbed was constructed from mine map elevation points. These data and 2-ft surface contour maps were used to measure the precise location of the coal outcrop. The actual discharge point was as little as 425-ft away from a thinpillar section and 475-ft away from a pillar recovery section. The discharge point was found to be located slightly above the coal, indicating that the drainage path was at least partially through the strata directly above the Upper Kittanning coalbed. Hydraulic conductivities and potential discharge pathways are analyzed and discussed. The possible factors influencing the performance of the down-dip barriers at Solar No. 7 and Solar No. 10 are: a) the width of the barrier, b) the applied hydraulic gradient, c) the type of mining adjacent to the barrier, d) the overburden, e) the pattern and characteristics of fractures, and f) the quality of waters contained within the mine pools. This study, part of a larger effort funded by the Appalachian Research Initiative for Environmental Sciences (ARIES), is tasked to determine the key factors responsible for the successful design of down-dip coal barriers.

Jan 1, 2013

By Katya V. Babenko, Victor V. Nazimko

We address the problem of the stochastic nature of ground pressure manifestation. Stress distribution in a rock mass and ground irreversible movement are governed with a set of random factors that affect the over-peak strength of the rocks, making them extremely sensitive to any perturbation of the external environment and to internal fluctuations of the thermodynamic state of the rock. We investigate the fluctuation evolution during a longwall face movement to find out whether the fluctuation dissipates or builds up. Five adjacent powered support failures simulate the ground pressure fluctuation. The main roof has been presented as a plate that reposed on the rigid base. The stiffness of the base depends on the thickness of the extracted coal seam and on the dilation of the caving roof. Maximum stiffness occurs in situ, and minimum stiffness is in the gob when the roof is highly flexible and subsides elastically, without caving. The more stress acts in the roof, the higher the cavity that occurs and the larger increment of the base stiffness. The wave of the fluctuation has extended both to the direction of the longwall advance and along the face from the point of the fluctuation agitation. There was an incubation period when the fluctuation was negligible, and the process of the main roof caving remained unaffected. The distance of the longwall advance during the incubation period was twice the longwall length when the fluctuation magnitude was 1% relative to the maximum possible disturbance and 0.76 of the longwall length for the magnitude of 24%. However, the pattern of the roof caving has dramatically changed during further movement of the longwall. All caving parameters have changed: step of the caving, ground pressure distribution, and the manifestation in the longwall and entries. A histogram of the fluctuation magnitude is symmetric in accordance with normal distribution. However, the distribution has abnormal excess. These findings are the first step toward answering the question whether it is possible to forecast the process of main roof caving and weighting consistently. Our preliminary conclusion is that the space and time intervals where this prediction can be made with certain reliability are limited, so further investigation is needed.

Jan 1, 2017

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff' backflll to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

By William Blake

Mining induced rock bursts have been a severe operational hazard associated with the deep silver mines of the Coeur d'Alene mining district for over 30 years. Recent studies during the past fm years have led to a better understanding of the different types of rook bursts and their causative mechanisms. This has resulted in ground control measures that more effectively minimize burst occurrences as well as contain burst damage. Case histories of burst incidences and examples of control measures are presented.

Jan 1, 1987