Search Documents

By A. MacG. Robertson

INTRODUCTION The tailings, or solid waste, remaining after uranium has been extracted from an ore and the liquid wastes associated with it contain both radioactive and other substances which, if released to the environment, may have a detrimental impact on man and his environment. Although the radioactivity of the waste is of natural origin, the mining and milling process results in bringing the radioactive ore to the surface, changing its chemical and physical form, increasing its mobility and, therefore, enhancing the potential radiological exposure to man. Exposure to radionuclides released from a tailings impoundment, while small as applied to any one generation, can be made large by counting far into the future, large enough to be the dominant source of exposure from the nuclear fuel cycle, Cunningham (1978). Increasingly it is being found that where the prime concern was initially the radionuclide releases, the release of other pollutants and contaminants may be of equal or greater concern. While there is a definite benefit, at least to present generations, resulting from the recovery of uranium, current and long-term concerns require that consequential present and future releases be kept as low as is reasonably achievable. Design practice, to minimize this release, is currently passing through a technical revolution; precipitated by public and institutional concerns. New techniques and methods are, therefore, being actively sought and continuously implemented. Because of the complexity of the pollutant release mechanisms and the sitespecific nature of each impoundment site and tailings product, a wide variety of site selection and design options have been implemented or considered. It is often possible to design a number of satisfactory tailings disposal schemes which differ widely in nature and cost. This paper outlines the principal areas in which options are available and discusses some of these options. Both operating and post-decommissioning conditions are consi-

Jan 1, 1980

By John W. Conn, Harry C. Verakis

An explosion in an underground coal mine can have a devastating effect on the main fans used to provide mechanical ventilation. The Code of Federal Regulations, Title 30, Part 75.310 (CFR, 1992), specifies that each main mine fan shall be offset by at least 15 feet (4.6 m) from the nearest side of the mine opening unless an alternative method of protecting the fan is approved in the ventilation plan. Also, each main mine fan shall be protected by one or more weak walls or explosion doors. This paper presents venting and fan configuration designs which provide a comparable degree of safety for explosion protection. Design flexibility is enhanced and a means for consistency in safety judgements is afforded.

Jan 1, 1993

By Margaret Fuller Boos

Precambrian granitic pegmatites on the west, south west, south and southeast slopes of Storm Mountain, Larimer County, northern Colorado, were explored and mapped geologically 1956-1959. The area between Crystal Mountain Mining District on the north and Hyatt pegmatite mine area on the south was nearly inaccessible until a company built an access road, which was completed in 1959, into Roosevelt National Forest and its jeep-type roads. The area is extremely rugged, rising from some 6,000 feet on the highway at Drake, on Big Thompson River, to an altitude of over 10,000 feet at the summit ridge of Storm Mountain. Almost innumerable pegmatites of every possible type of granitic pegmatite intrusion infest the Precambrian gneisses and schists of the southwest-tilted fault block of Storm Mountain. The major bodies stand at least 100 to 200, feet high above the surrounding forest floor. Core drilling has shown that some extend to at least 200 feet below the surface. They blunt out at the southwest, some keel out below and others are faulted out at their southwest ends. Strike length ranges from 200 to 600 feet. The massive bulky bodies have nearly vertical walls. Contents are zoned or ribboned and layered. They consist of local commercial bodies of beryl, potash feldspar, mica, uranium minerals and quartz. As yet no lithium minerals have been encountered.

Jan 1, 1960

By D. Gill, R. Burgess, B. Kyslinger

"There is always a demand in the mining industry to improve the safety and efficiency of roof bolting. Since 2008, Anglo American and Fletcher® have been working together to develop a new roof bolter concept that is safer and more ergonomic while maintaining current production rates. The recognized types of machines currently used in South Africa are always under constant review for improvement; however, there are limitations to the current design. The majority of the machines in South Africa are the “Man in Position” roof bolters. There are currently over 200 of these roof bolters in South Africa, with the bulk of the machines being twin-boom units. When operated correctly, these machines are safe, versatile, reliable and productive. However, with the operators located close to the drilling and bolting operations, they can be exposed to operational hazards. In addition, the major amount of material handling can be quite difficult on an operator. Anglo American, with a desire to improve safety, approached Fletcher to develop a remote style machine with simplified controls that maintained the productivity of the twin-boom machines. After several prototypes, the current model was developed. The chassis was designed for better operator comfort. A dual mast drill module was implemented to reduce the total time to bolt a cut. A remote operator’s station was incorporated to remove the operator from the front of the machine. The design was all about producing a safe and ergonomic machine from front to rear. This paper will explain the evolution and technological advancements from earlier prototypes to the current production machine. INTRODUCTION With mining, especially coal extraction, comes the necessity of supporting the roof. Since the 1950’s, the primary method for roof support has been the use of roof bolts. Roof bolting is considered one of the most hazardous jobs in underground coal mining. In 2004, there were 3,405 injuries reported to MSHA (Mine Safety and Health Administration). Of those injuries, 17 percent were associated with bolting machines (593 injuries). The majority of the injuries resulted from rock falling from supported roof. However, injuries involving a part of the body being struck by, or caught between, during bolting and drilling occurred with relatively high frequency (Burgess and Steiner). Roof drilling and bolt installation is labor intensive and repetitive. These labor intensive and repetitive requirements can lead to cumulative trauma. Operators are expected to perform a considerable amount of lifting, carrying, bending, reaching and stretching. Back and shoulders become sore from bending and twisting to install bolts or lift and position drill steels, wrenches and bolts. Confined operator spaces also contribute to difficult and awkward working positions for the operators (Cornelius and Turin)."

Jan 1, 2017

By D. Yeager

Researchers at the U.S. Bureau of Mines have successfully used a genetic algorithm to tune computer models of three column flotation units simulating a separation circuit. The computer models rely on empirical constants that are selected so that the models accurately predict the performance characteristics of individual column flotation units. Unfortunately, these empirical constants have traditionally been selected using a time consuming trial and error process. A new and more efficient approach to selecting empirical constants for computer models has been developed. A genetic algorithm has been used to select the empirical constants for column flotation models used to simulate a three column circuit. Genetic algorithms are search algorithms based on the mechanics of natural genetics. They rapidly locate near optimum solutions in difficult search spaces. Bureau researchers have used these innovative search algorithms to dramatically reduce the time needed to select empirical constants for column flotation models. The approach is applicable to the selection of empirical constants for numerous other computer models.

Jan 1, 1995

By Greg Bold, Mahmood Khwaja, Yuannian (Jerry) Wan, Michael S. Schultz, William Simcoe

Beaver Creek Clean River Project will satisfy the consent decree requirements by capturing and treating combined sewage overflows. The project consists of, approximately, 2,700 feet of 30-inch trenchless pipe installation, a new screening/disinfecting facility, an expansion of an existing diversion structure, and a 72-inch internal diameter, 530-foot long mined tunnel. The tunnel portions are being progressed as early release packages. This paper presents the geotechnical exploration program and the subsurface conditions encountered; interpretation of the geotechnical conditions; and, approach to developing stand-alone packages for the tunnels to mitigate construction and schedule risks and continue to advance the project.

Jun 13, 2021

By M. H. Col

Within the last few years, there have been numerous techno-logical advancements within material handling due, in part, to the introduction of conveying systems and mobile material handling systems to the industry. Although the traditional material handling methods are still commonly used, the introduction of conveyors to the industry has provided companies with some very efficient and economical options. These "new" systems change with the industry to accommodate rigorous demands, ease of operation, and low operating cost requirements. The number of mobile material handling systems utilized in mining operations is increasing, especially in heap leaching applications. Ten years ago, mobile material handling systems like Mobile Stacking Conveyors (MSC) were considered a novelty. There were two (2) MSC's in actual operation and only one of those in a heap leaching application. Today there are numerous proven systems operating at mine sites around the world-La Coipa, Zaldivar, Florida Canyon, Cananea, El Abra, Chuquicamata, and Radomiro Tomic. The popularity of mobile systems is due to the benefits realized by individual projects. As technology advances, so do the concepts behind mobile material handling systems. Implementing self leveling mechanisms, Programmable Logic Controllers, and Global Positioning Systems to control the equipment are just a few of the recent advances that will be discussed in this paper. We will also discuss current proven systems, and touch on what we see as some of the future advances.

Jan 1, 1998

By David E. Peterson, F. Merz

The Waihi Gold Mining Company Limited, Martha Hill Project was the first major hard rock mining operation following the resurgence of the mining industry in New Zealand. Because of its location adjoining a town and at the southern part of the sensitive Coromandel Peninsula, the operation received a high level of public scrutiny. Very srrict limits for effluent criteria had to be met and led to the necessity for advanced wastewater rreatment technology. The process technology selected was the copper catalysed oxidation of cyanide using hydrogen peroxide, with subsequent removal of heavy metals by precipitation and filrration. This paper discusses the adoption of environment limits together with the detailed description of the plant and design criteria. Data of the one year's operational history is also presented.

Jan 1, 1991

By M. G. Schulz

Mining of molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock-types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the ore body. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1985

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

"On-site research and development as well as in-situ testing are key factors to the successful implementation of new mining equipment and technology. Unfortunately the demands and necessities of research and development often conflict with the reality of mine production in operational mines, especially during early stages of research and development and the initial testing of new equipment. Several experimental mines under university supervision attend to this problem and provide a close-to- reality testing environment for the mining industry and mining equipment manufacturers. This paper gives an overview of the design and organization of such an underground testing area as well as of the wide range of possible operations it can facilitate at the example of the FLB Experimental and Teaching Mine (Forschungs- und Lehrbergwerk) at Technische Universität Bergakademie Freiberg, the central European underground research mine. INTRODUCTION As well as the Mining Engineering education follows the same pattern worldwide, the tasks and duties to be fulfilled by engineers in the productive mines are comparable around the globe. This also holds true for the technologies and equipment needed, both in surface and underground mines. Almost all mining equipment brands are being distributed worldwide. The tasks and challenges of guaranteeing an ever- increasing productivity at the mines, while simultaneously maintaining, respectively improving, safety standards, also in the developing countries and emerging economies, requests a constant development, improvement and adaption both of the engineering education and of R&D in technology and equipment. The increasing safety requirements at the mines, in combination with also increasing safety and liability policies, do often not allow a proper practical education of mining engineering students. At the same time, new technologies and equipment to be deployed / brought to the mines have to be fully functional in a production operation from the very first moment. Time losses like break-down time or even repair and maintenance breaks are often costly and, even when expected up to a certain degree with newly developed machines, have a wider negative impact on the neighboring operations and operations within that mine, thus often being unacceptable within the ongoing production process and extremely costly."

Jan 1, 2015

By H. Yoon

Several processes involving injection of sorbent and humidification water downstream of the air preheater in a coal-fired boiler unit, are being developed as low capital cost retrofit S02 control options. Extensive laboratory work, pilot plant programs and larger scale programs have developed performance data and design information. Many of these programs were supported by the U. S. Department of Energy (DOE) as "proofs-of-concept" of three different processes proposed by Dravo, Bechtel and General Electric. Based on these project results, DOE formulated a comprehensive in-duct sorbent injection development program to fully commercialize the technology by 1992. Also, EPRI will conduct a 4 MWe pilot program to develop its HYPAS process. The Consol Coolside process is scheduled for utility demonstration in 1989 on a 104 MWe unit at the Ohio Edison Edgewater Station under partial sponsorship of the DOE Clean Coal Technology Program.

Jan 1, 1989

By Xiangze Shu, Yuzhong Xing

All programs used to optimize main fan nowdays have to be run on the large and medium- sized computers. With a lot of array elements, complex processes, low convergence speed and large storage, these programs are both time consuming and difficult to be used in the micro computer. This program uses two languages (dBASEIII and BASICA) to calculate the network and to choose the fan respectively. It allows user to compare and choose the parameters of various kinds of fan and to transfer the selected fan parameters to the master program by a data communication system. Then the user can get the air quantity, the air pressure, the power and the efficiency of the main fan. The advantages of this program arc as follows: 1. It can be run on IBM-PC or compatible micro computer. 2. It can select a fan more quickly and less time consumingly. 3. It can choose desired one or a set of fans according to user's requirements. 4. It is suitable for the research institutions and coal mines.

Jan 1, 1991

By Douglas W. Barr

Water is a necessary part of our environment. It is a biological necessity, but more than that, it is a necessary part of our life style. Those of us who live in the north woods expect water to be part of the scene. There are few natives of this region who would be content to eliminate the streams, the lakes, the marshes, or our forests. Throughout the world, water has been so much a part of man's environment and man's adaptation to life has been so closely tied to water that our way of life and ways of accomplishing our work include water as an essential tool. The production of taconite is an example of our dependence on water. Other methods could have been developed to process taconite ore but the process methods chosen utilize water. Water is used for grinding and separation and for trans- porting the ore from one part of the process to another and for dust control. A typical large plant producing 10 million tons of taconite pellets per year will have on the order of 130,000 gallons per minute (8.202 m 3/51 of water in circulation in the plant. About 120,000 gal. per min. (7.571 m 31s) will pass to tailing thickeners where 110,000 gal. per min. (6.940 m 31s) is separated from tailing and returned to the process. About 15,000 gal. per min. (.9464 m 31s) goes with thickened tailing to tailing basin. My point is that there are great volumes of water in motion in a taconite plant,

Jan 1, 1980

By Birger Schmidt

The design of underground nuclear waste disposal facilities poses new problems related to the requirement of long term safety against radionuclide migration. The degree and effects of rock disturbance caused by construction and by the long term thermal effects from the hot waste must be predicted with confidence. Computer modeling can, to an extent, be verified by accelerated near-surface tests. Credible extrapolation to deep, long-term conditions requires successful near-surface modeling verification, proper characterization of near-surface and deep rocks, and successful determination of in-situ stresses. Excavation induced disturbance may be assessed primarily by empirical evidence.

Jan 1, 1981

By Robert R. French

Beneficiation of-low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, electric and magnetic properties of the ore and gangue are similar the possibility of separation by color, reflectivity, or fluorescence offers hope for utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Electronic color sorters were first designed to process agricultural products and were small low-capacity units. However, the recent introduction of larger machines designed to process 6-in, diameter ore at a rate of 30 to 50 tph (Anonymous, 1966a), has brought color sorting into the capacity range required by many mineral producers.

Jan 1, 1967

By P. Christmann

The operational paradigm of mining industries is shifting from ?optimal profit for the financial stakeholders? to a new concept compatible with sustainable development ethics: ?maximize economic and social returns at the local, national and global levels, while avoiding negative environmental impacts?. The number of stakeholders concerned by mining companies has grown significantly over the last few decades, and the role of local communities and civil society is now acknowledged by the mining companies adhering to the sustainable development ethics. ?Involve me? is becoming a key to maximize the returns the mining industry can provide to sustainable development. As the world?s major importer of many mineral commodities, several coming from developing countries facing severe short-term problems, the European Union (EU) is an important stakeholder and has a responsibility in supporting actions to strengthen corporate and public governance capacities. The purpose of this paper is to highlight the drivers leading to the development of sustainability indicators and to propose, within the 6th European Framework Programme for Research, Technological Development and Demonstration Activities (FP6), an European-level initiative to develop sustainability indicators adapted to the mining industry and its population with relevant data.

Jan 1, 2003

By R. H. Weiland

The dewatering of flocculated clay suspensions by compression in a centrifugal field has been investigated. The results are evaluated with regard to both direct applicability to centrifugal dewatering, in solid-bowl centrifuges for example, and indirect applications to gravity sedimentation systems. It is well known that sediment consolidation under gravity depends on structural characteristics such as permeability and on the "self-weight" of overlying sediment layers. An important objective of the study has been to evaluate the self-weight effect using centrifugal forces to simulate consolidation in deep sediments. In this way, small-scale laboratory tests can be used to predict the rates and limits of sediment compression in industrial systems such as thickeners and settling ponds. Experiments have been conducted in which the sediment mass and initial structure were maintained constant while the effective sediment weight was varied by centrifuging at different speeds. The effects of initial structure have also been studied using controlled variations in flocculation conditions.

Jan 1, 1993

By Stanley Dempsey

INTRODUCTION The mining industry has been under- going a significant restructuring for the past several years. Some firms have been liquidated. Some have been merged with other firms. A number of mining divisions of larger firms have been spun off, in some cases in leveraged buyouts by management. Recently, there have been a number of spin outs of gold subsidiaries. There are also a number of start-up situations where new firms are emerging as significant gold producers through mine development or acquisition. This restructuring has created an attractive market for specialized mining finance firms, and a number of firms have recently entered that field in the United States. These firms provide financial advisory and valuation services to mining firms and project developers, and access to venture capital. In some cases, they invest for clients or for their own account. I have been asked to describe how our firm works, and what kind of information we expect to receive when mine developers seek our assistance in financing a project. HOW WE OPERATE Denver Mining Finance works for both mine developers and investors. We also provide expert advice on mining issues to governments and to firms who are in litigation over mining issues. A lot of our work involves valuing mineral interests for various purposes. Our principal expertise is in the technical, commercial, and financial area. We help put mining deals into shape commercially so that they can be financed, and we help investors get into mining deals that are commercially sound. We work on projects, but we also advise mining firms on the structure of their business and how to make the most out of one or several mines that they might own. In addition to our work for clients, we are also prepared to invest in mining projects for our own account, and to recommend gold properties for acquisition by our parent company, Royal Gold, Inc. We are, to some extent, a venture capital firm, in that we sometimes work with projects that are not "bankablerV1 and are prepared to invest in attractive early-stage situations in mining. However, I want to emphasize that our principal focus is on development of commercially attractive mining projects that can be brought into production in the best possible financial terms. If we can make a project qualify for a project loan from a commercial bank, we will not advise the developer to use high cost venture capital. For the purpose of this paper, I will focus primarily upon our functions with respect to development of precious metal projects. In a typical case, a firm with an advanced-staged project approaches us for help with financing the final feasibility study, and construction and operation of a mine. In some cases, the developer has already developed a financing plan and wants only our access to investors. If we agree that the project is sound and that the financing scheme will be attractive to investors, we will help the developer reach investors on a commission basis. In such cases, we are particularly insistent that the financing plan and our participation meet all regulatory requirements, particularly compliance with state and federal securities laws. In most cases, however, the developer asks us for advise both on how to structure the financing, and how it can be implemented. Here we work for fees based on hourly rates for advisory work,

Jan 1, 1987

By G. A. Kordosky

The control of pH in solvent extraction circuits is an old technique (1,2) but one which has a large potential for future use. The equilibrium position of any reaction which has hydrogen or hydroxide ions, either as products or as reactants, can be controlled by pH adjustment. Several examples of reaction types which are important in solvent extraction systems and which also show a pH dependence are shown in Figure 1. The examples were chosen to show the wide variety of reactions which fit the above criteria, but it is not meant to be a complete listing of all the possible reaction types, Some of the reactions are presented in a simplified form. It is the intent of this paper to discuss pH controlled solvent extraction reactions for some relatively simple systems through more complex ones.

Jan 1, 1979