Search Documents

By T. W. Peterson

There are two approaches to developing a minicomputer based application for an industrial grinding circuit. Usually, the control program is coded and compilation-debugged on a large-scale scientific computing system or the minicomputer itself if the machine is available. Final debugging and testing must wait for installation and checkout of the entire minicomputer system. Two immediate disadvantages of this approach are the need to obtain, install and check out the hardware before the final debugging stages of program development can begin, and interference with normal mill operation during such final testing. This work reports on an alternative to the usual procedure. Here both compilation and execution bugs are eliminated from the application program before hardware installation by testing the control program against a reasonable dynamic simulation of the entire process. Thus, software development can be completed before the target mini is installed. Such off-line development requires a reasonably accurate mathematical model for the entire process system as well as a suitable simulation package for communication between the simulated environment and the minicomputer application program. Specific data describing the design configurations and dimensions of the mills, cyclones, sumps, pump characteristics and analog controller configuration were supplied by ANAMAX for a grinding division consisting of a rod mill followed by two ball mills in parallel. This information was used to set up a plausible model structure. Steady state ANAMAX data on particle size analysis at various points in the circuit and corresponding values of flow rates, pump speeds, sump heights and slurry densities were used for model parameterization. The preferred operating control strategy - "best grind at operator-set rod mill feed rate" - was set by ANAMAX. An inferential particle size analysis technique using the cyclone cluster as an on-line particle size sensor was used in a novel control strategy_ to achieve the stated objective. Two disturbances common in the ANAMAX circuits - rod mill scoop pluggage and shut down/start up of one of the ball mills - were studied in detail. This report out- lines the steps in system development and testing and the results obtained.

Jan 1, 1974

By Paul H. Lu

This paper proposes a novel method, "integrity factor approach," of mine-pillar stability evaluation based on in situ triaxial-loading measurement. The pillar integrity factor is defined as the quotient resulting from division of integrated total pillar strength across the critical dimension by the integrated total pillar load across the same dimension. The integrity factor is dynamic, while the conventional safety factor is static. With this approach, the pillar stability can be evaluated at any stage of mining progress during panel operation. It automatically considers the progressive failure of the pillar and post-failure strength without the need to clearly define the boundary between yielded and intact zones of the pillar. Based on two case studies, the integrity factor approach is shown to be a practical, effective technique for evaluating stability of conventionally designed pillars. It is suggested that a more realistic estimate of in situ pillar strength could be made based on the combination of in situ triaxial-loading measurements and laboratory true triaxial compression tests, rather than through the traditional combination of biaxial-loading measurements and conventional triaxial compression tests.

Jan 1, 1986

By Ch. Roumpos

The present contribution investigates the way of applying benchmarking for large-scale open-pit mining operations based on sustainability indicators proposed by numerous institutions or groups of experts. These indicators have been developed taking into consideration the legal and regulatory framework that are in force. However, their scope is not only to declare the mining company?s compliance with all legal requirements but also to represent its economic, environmental, and social performance. In this way, sustainability indicators allow assessment of a company?s capacity to produce commodities, to meet the environmental quality requirements and to contribute to a long-term economic, cultural and social development of the local communities.

Jan 1, 2007

By Raj K. Rajamani, Ilesh M. Shah

Maintaining pH, a routine requirement in many industrial processes, is by no means trivial. The control is troublesome because of the inherent nonlinearity and frequently changing process dynamics. Many researchers in the past have investigated advanced on-line estimation and/or adaptive control techniques to overcome these difficulties. Most methods require the development of a complex mathematical model. The present work deals with the use of a simple and elegant method for pH control, based on the use of fuzzy logic. First, a standard fuzzy-logic controller is discussed, followed by a self-organizing controller. The latter algorithm generates a set of rules based on observation of the process. Thus it is a learning algorithm. The development and application of the algorithms to a laboratory acid-base neutralization experiment are presented. This elegant technique is powerful and deserves attention in mineral pro- cessing.

Jan 1, 1990

By W. S. Fyfe

Gold is mobilized or made soluble under all crustal conditions given appropriate fluid chemistry with molecules which complex gold. In the surface environment chloride, thiosulphate and a host of organics may mobilize gold. In the epithermal range bisulphide appears effective as shown by the classic studies in the Taupo volcanic zone of New Zealand. In the high grade metamorphic to igneous ranges little is know but it appears that gas molecules in the system CO2 -CO-H20-S-C1 can do the job. Precipitation may occur by changes in P-T-EL-pH or boiling where such changes influence the liquid concentration. Of the known regimes information is good for epithermal systems, poor for surface lateritic environments, inadequate for high-T systems. Gold is often concentrated in bio-systems both living and dead. The influence of biosystems is little appreciated. There is a great potential for the discovery of new types of gold deposits and in particular, gold in weathering environments, gold in very high-T environments, gold in strike-slip faults and thrust regimes, and gold as a by-product in materials like coal and other organic debris. By the year 2500 we may find our noble metal resources in the asteroids.

Jan 1, 1987

By Ricardo Presnell, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Douglas N. Halbe

Large (> 100,000 oz.) sediment hosted disseminated gold (SHDG) deposits are often spatially associated with anticlines. Many SHDG deposits are within or closely associated with windows. Windows are erosional manifestations of fold culminations (4-way closed anticlines). Hydrocarbons are often trapped in fold culminations in the Canadian Rockies, and may account for degraded hydrocarbons in many SHDG deposits. In the Eastern Basin and Range Province, Mesozoic anticlines may have been large scale conduits fm gold bearing Mesozoic and Cenozoic hydrothermal fluids which became trapped and/or concentrated at the fold culminations.

Jan 1, 1990

By M. B. Thorpe

Land use and access to land are limiting factors in economic development in the Western region of Ghana. Mining uses land during operations and then rehabilitates the land as part of ongoing operations and closure. Golden Star Resources Limited (GSR) aims to contribute to the sustainability of the local economy during its operations and then post-closure. Following a series of alternative livelihood initiatives, GSR reviewed the success of these programs and decided to focus on an oil palm project that uses out-growers to reach the local economy. The project started using small holdings that were individually managed. However, the ongoing effects were limited. Following a review of the options, the Golden Star Oil Palm Project was started using land committed to the pro-gram by the Bogoso Mine. The initial program covered 275 ha with over 40,000 trees with 300 people involved in the development. The Traditional Authorities have committed additional lands to the project to a planned total area of 18,000 ha.

Jan 1, 2007

By H. Wagner

INTRODUCTION One of the most important tasks facing the opera¬tors of deep-level gold mines is supporting the roof strata in the immediate vicinity of the stope faces. Some of the deeper gold mines operate at depths ex¬ceeding 3.0 km; the extreme mining depths and the tabular nature of the gold-bearing reefs result in high stress concentrations at the abutments of the stope faces. These, in turn, lead to extensive fracturing of even the hardest quartzites. Although most of these fractures develop in a stable manner, there have been many instances where rock failure occurred suddenly, resulting in a considerable amount of damage to the underground workings. Such violent rock failures commonly are known as "rock bursts," and they are typical of many hard-rock mines that are operating at great depths. To safeguard mining personnel and equipment against the effects of stable and unstable rock failures, adequate support must be provided to the fractured roof as quickly and as effec¬tively as possible. Traditionally, timber props and timber packs have been utilized to provide roof support in gold mine stopes up to 1.5 m wide. Both methods of support suffer from the fundamental disadvantage of generating sup¬port only in reaction to movement of the strata. Since unrestrained strata movement often results in a break¬down of the frictional forces that preserve the stability of the intensely fractured roof strata, it is essential that stope supports have rapid load-bearing characteristics. An equally important requirement is that the roof sup¬ports be able to accommodate displacements of the rock mass. A third requirement of roof supports in gold mine stopes is that they must be able to accommodate the high rates of stope convergence typical of rock bursts. The hydraulic prop is the obvious choice for sup¬porting the stope faces in deep-level hard-rock mines. Since hydraulic props can be installed with a positive setting load, they can provide roof support that is independent of strata movement. By equipping the hydraulic props with yield valves, they meet the require¬ment of being able to accommodate rock-mass displace¬ments. However, the requirement of being able to accommodate high rates of stope convergence without overloading or damaging the rock strata was rather difficult to meet. The first introduction of hydraulic roof supports into gold mine stopes showed that conventional hy¬draulic props, such as those used in coal mines, were completely unsuitable for a number of reasons, in¬cluding: 1) Since drilling and blasting are used to break the ore in gold mine stopes, supports installed close enough to be effective are exposed to the vigor of the blast. Conventional coal-mining props suffered extensive blast damage, despite being protected by a blast barricade. 2) The environmental conditions in gold mine stopes favor corrosion. The high quartz content and the abrasiveness of the ore further aggravate the problem by damaging the protective coatings on the hydraulic surfaces. Simply changing the design of gold mine props to have the piston project from the bottom rather than from the top resulted in dramatic improvements in the service life of the props. The improvement was attributable to external water in the stope washing the fine quartz grit away from the hydraulic surfaces, rather than concentrating the particles between the cylinder and piston of the prop. 3) The most obvious deficiency of conventional coal mining props was their inability to yield rapidly enough to accommodate the high convergence rates of rock bursts without overloading the supports. As a result of the first disappointing results with hydraulic supports in narrow hard-rock stopes mined by drilling and blasting, a comprehensive research and development program was undertaken. The hydraulic props resulting from several years of research and exten¬sive field trials are described herein. To date (1978), more than 130,000 of these props have been manufac¬tured and used successfully in a number of mines and under a variety of geological conditions. Although many of the detailed specifications are directed spe¬cifically to gold mining conditions, there are a number of points that are of general importance in the design of underground support systems for tabular excavations in hard-rock mines of any type. SPECIFICATIONS FOR RAPID-YIELDING PROPS Yield Requirements The yield requirements for hydraulic props in deep¬level hard-rock gold mines are summarized in the fol¬lowing paragraphs. Slow Yield Load: The design of the yield valve must allow the yield load to be preset to between 300 and 400 kN. This flexibility is necessary to account for the differences in the strength properties of the roof and floor strata. Drop in Load Under Slow Yield: The drop in sup¬port load during a slow yield should be as small as possible, but it should not exceed 5% of the slow-yield load. Rapid-Yield Load: The load exerted by the prop during periods of rapid stope convergence should be as close as possible to the slow-yield load. The rapid-yield load should not exceed the slow-yield load by more than 15% at yield rates of 1.0 m/s. The limitation of the upper valve of the yield load is important; it deter¬mines the hydraulic performance of the yield valve. The hydraulic props that satisfy this criterion have performed well, even under severe rock bursts. Load Changes Under Rapid Load: On some of the earlier rapid-yielding props, conditions of dynamic in¬stability were observed; these conditions resulted in a complete breakdown of support resistance. It is essen¬tial that the force oscillations during rapid yielding be as small as possible, not exceeding -*5% of the average rapid-yield load at a yield rate of 1.0 m/s. Longitudinal Resilience: During rock bursts, vibra¬tions of the roof and floor sometimes are observed. To

Jan 1, 1982

By Vincent J. Murphy

INTRODUCTION Geophysical applications to engineering projects are usually considered for reconnaissance exploration, and for some preliminary design phases. Recent experience indicates a growing need and a greater number of requests for measurements during construction. This is particularly true where seismic velocity values are related to strength properties of rock. Typical project objectives during construction are: dike and tunnel realignments required by surprise conditions encountered during foundation preparation; checks on grouting effectiveness which require velocity measurements before and after grouting; and dynamic moduli measurements along the walls of tunnels and deep excavations. This paper considers one of the on-site seismic applications that is rather simple and straightforward, and yet has few references in the literature. The specific objective is the measurement of seismic velocities (both "P" waves and "S" waves) for determining the thicknesses and dynamic moduli values of loosened zones of tunnel wall rock. PRE-EXCAVATION SEISMIC METHODS The seismic methods suitable for engineering project studies are well known and especially suited for routine site reconnaissance; these are illustrated in Fig. 1. The seismic refraction profile with a

Jan 1, 1997

By Robert F. Baker

Neanderthal technology is a harsh and inaccurate way to describe modern underground construction and mining practices, but such an exaggeration helps to focus on a major problem or wasted opportunity of modern society. Why is it not safer to excavate in the underground? Why are the working conditions still so unfavorable? Why are urban freeways, shopping malls, warehouses, power plants, sewage disposal treatment plants, and similar facilities still constructed on the surface of the ground--because it is a better location? On the contrary, if underground technology made full use of existing knowledge, underground resources and space would be much more effectively used. And why is the technology so inadequate? Certainly, researchers and practitioners are aware of the shortcomings and are equally aware of problems that have to be overcome. One of the most important reasons has to do with the type of policy goals that society has set in the past. Policy makers may have agreed that improvements would be desirable but no serious commitments have been made--that is, there has been no major allocation of resources to advance these technologies. And yet, to bring about significant changes will require significant time and resources. The resources that are needed are far in excess of what industry can afford to invest, particularly since the pay-off may be far in the future. So the problem reverts to society in general. As long as society is willing to tolerate the present costs and safety requirements for recovering minerals and for constructing underground facilities, then the changes will be slow in coming. Until such time as society sees and desires the benefits

Jan 1, 1974

By Bruce D. Hanson

A computer model capable of simulating the basic production system in a variety of underground mining methods has been developed at the Twin Cities Mining Research Center. This Bureau of Mines paper describes the simulation of the basic production system at the working face, which includes drilling, blasting, mucking, and roof bolting. The model is event-oriented; that is, the status of the system is updated at the occurrence of an event. All event or activity times, including failure and repair of equipment, are treated as stochastic variables. A location dimension, in addition to the time dimension, is used, allowing the simulation of multiple location systems. To aid the user in determining the efficiency of his system, the model provides several reports. An event or activity report gives the frequency of occurrence total active time, and cumulative delay statistics for each event. An equipment report delineates the availability and utilization of all equipment. A production report provides information on various performance measures such as tons produced and holes drilled. The cost report gives the cost of various elements in the system. Operating data from an actual mining situation were used in validating the model. In addition to the description of the model, examples of simulation experiments which were performed on a room-and-pillar mine system are given. Use of the model to determine methods for improving the efficiency of the system is discussed.

Jan 1, 1974

By B. M. Davis, J. Wilkins

The method of conditional simulation is easily implemented on the personal computer when the LU decomposition algorithm of Davis (1987) is employed. This algorithm is fairly compact, yet can generate moderate-sized simulations in a few minutes on a 80286 or 80386-based personal computer. The application of conditional simulation presented here is to generate possible ore inventories from a limited amount of exploration sampling. The simulations can then he examined to decide if the potential inventories are sufficiently attractive to proceed with further exploration. An example showing one application of this approach is presented.

Jan 1, 1992

By F. F. Aplan

Rather than reiterate what is well known about the flotation of the non-sulfide minerals, emphasis has been placed on those separations which are not so effective. These difficult separations are largely connected with problems of selectivity in the flotation of the base metal oxides, the other slightly soluble minerals, the insoluble oxides and the naturally floatable minerals. The paper discusses possible methods of improving selectivity between similar species and of improving selectivity against the gangue minerals.

Jan 1, 1994

By Sandra L. Maxfield, Alan Mair

Strategic design of groundwater monitoring programs can increase public confidence in mine management, decrease financial assurance requirements, and minimize environmental budgets. Monitoring of inorganics is challenging because many occur naturally with baseline concentrations fluctuating spatially or temporally. Evaluating monitoring data to distinguish between a hazardous release or a natural fluctuation in baseline concentration can be controversial. In order to develop an effective program, monitoring parameters should be selected which are mobile and stable. Statistical procedures should be customized to address the uniqueness of groundwater systems. Calculated baseline concentrations should minimize the false negative & false positive rate.

Jan 1, 1995

By Khosrow Bakhtar, Robert E. Cameron, Arfon H. Jones

The use of rock simulators in rock mechanics research greatly expands the scope of the problems that can be investigated with physical models. However, the exact reproduction of full scale conditions, or absolute simulitude, is not obtainable on a small scale model. For this to be possible, the scales of length, time, and pressure (or mass) must be changed without altering the theoretical equations that describe the behavior of materials concerned. In using rock simulants for physical modeling of structures designed in rock, the geometry of full scale structure is reduced to a size suitable for the available testing machine. This will require the strength related properties to be scaled down. Simulation should be representative of the in situ conditions. Complete simulation will require that friction parameters and the stress ratios be matched exactly between prototype and model. The procedure involved in application of physical modeling for rock mechanics research is discussed in the following pages. Background, theoretical approach, and anticipated benefits to the research community are also elaborated.

Jan 1, 1986

By R. S. Farinato

Thionocarbamate flotation reagents have enjoyed a niche position in the recovery of copper sulfides and activated sphalerites since their introduction in the mid 1950's (Harris, 1954). Thionocarbamates containing an allyl group (-CH2- CH=CH2), introduced recently Lewellyn, 1985; Nagaraj, 1988; Avotins, 1991), are used commercially as collectors for copper sulfides and activated sphalerite. Laboratory flotation tests and plant usage have demonstrated that allyl-containing thionocarbamate collectors exhibit certain unique properties that distinguish them from the corresponding dialkyl thionocarbamates. Spectroscopic (FTIR, XPS) and wettability studies of N-allyl iso-butyl thionocarbamate (AIBTC) and its saturated analog N-propyl iso-butyl thionocarbamate (NPIBTC) adsorbed on copper at pH 9 were performed in order to investigate whether there were any fundamental reasons for these differences. Flotation tests were carried out on chalcocite, copper ore and an activated sphalerite.

Jan 1, 1993

By Ernest Peters

To model the zinc pressure leach, equations have been written that describe the rates of individual reactions taking place, including (a) oxygen mass transfer, (b) ferrous oxidation by dissolved oxygen, and (c) ferric reactions with ZnS and other minerals. In the continuous process, at steady-state, these take place at the same rate, and so the equations can be solved simultaneously. Model calculations using simultaneous equations are shown in graphical form to demonstrate the effect of different variables on the leach performance.

Jan 1, 1993

By L. Rudolphy, P. Tähkiö

"The cPlant is a modular flotation plant which has been designed to minimize capital expenditure and risk. The plant is based on a number of standard modules, for both flotation and ancillary equipment, which can be configured to give the required flowsheet for the ore being treated. All of these modules can be rapidly deployed and erected onsite, minimizing not only engineering time and site preparation but reducing the time taken to get the plant up and generating revenue. Given the paradigm shift in flotation circuit design that has been employed in the cPlant it may allow smaller, previously uneconomic deposits to be exploited and create a more cost efficient upgrade route for existing plants. This paper introduces the cPlant and presents a case study comparing EPC cost and development timing of a cPlant against a traditional flotation circuit design. INTRODUCTION In the development of any mining project the cost associated with process plant engineering, equipment procurement and installation can affect the financial viability of a project. This is of special significance for smaller scale mining projects which perhaps don’t have the mine-life or revenue generation to justify the payback on a modern processing facility. Listening to customer feedback and understanding the challenges that small to mid-sized projects can face lead Outotec to the development of the cPlant. Modularization of mineral processing plants isn’t a new idea with a number of examples being reported in literature for gravity gold (Cabot, Trudel and Cabot, 2001; Gray et al., 2006), dense medium separation (September and Abate, 2006) and even hydrometallurgy (Saario et al., 2013). All these plants have been developed to try to improve on the traditional economics associated with fixed processing plants. Using standardized modules to construct a plant reduces engineering time and design costs which can both be beneficial to the outcome of a project. In addition the modular nature of the plant lends itself to transport to remote sites and rapid installation with only minimal site preparation required. A plant of modular design also has several other advantages over its conventional cousins. Firstly it is relatively easy to expand by duplicating existing modules. Secondly the modules can be treated as building blocks for the process and rearranged if a change in conditions requires flowsheet adjustment. Thirdly, there is potential to disassemble and remove the modular units at the end of the mine life. The ability to easily disassemble, re-pack and transport the plant to a new location not only is important to the long term environmental footprint of an operation but can also be seen as a bonus to an operator that has a number of small ore deposits. If applied in this way modular plants have the potential to create a whole new operating model for previously unviable ore deposits."

Jan 1, 2016

By T. Luterbach, V. T. McLemore

"Trace element analysis of placer gold can be used as a valuable exploration tool in order to determine the original deposit source and locating lode gold deposits. Placer gold collected from multiple districts in New Mexico and Alaska, coupled with a broad database of previously analyzed placer gold samples indicate correlations between chemical signatures (especially gold, silver, and copper) and type of deposits (i.e., Au-rich copper porphyry deposits, Au porphyry deposits, and epithermal deposits). By completing a chemical analysis and determining the particle morphology of placer gold collected from these districts using an electron microprobe, patterns in the chemical signatures from each location can be used to examine chemical variability (1) within the individual placer gold particles, (2) within the same district and (3) among different districts. INTRODUCTION Although there are numerous past studies on the chemical composition of placer gold by Newberry et al. (1997), Melchiorre (2001, 2009), Townley et al. (2003), and McLemore et al. (2014), the gold analyzed tends to be collected from one or few specific districts. Rarely do those studies compare compositional results to additional districts, or elaborate on the correlation between the elemental composition of the placer gold and the original deposit source for the respective districts. This research analyzes the composition of placer gold from multiple districts and within the same district. There are a number of elements, which can, in various quantities, be present in placer gold particles. Native gold can be in complete solid solution with native silver and contain additional elements including Cu, As, Pb, Fe, and S. The chemical signature of the gold is determined by the thermodynamic conditions of precipitation and transport as well as the total metal content of the system. As Townley et al. (2003) explains, “These thermodynamic conditions and metal budget differ from one type of hydrothermal deposit to another, and hence different deposit types will each have a characteristic gold compositional signature.” Identifying this signature can be a highly valuable tool in exploring for gold, as it can not only be used to determine the original source deposit of the placer gold, but provide valuable insight as to the erosion level of the present deposit."

Jan 1, 2016

By A. Perelli Cippo, R. Granata, D. A. Bruce

During the last few years, significant advances continue to have been made in aspects of grouting technologies used for ground treatment in advance of tunnelling. In permeation grouting, fundamental researches have continued into improving the penetrability characteristics of cement-based grouts. The twin advantages of field regrinding normal grouts to reduce cement particle sizes, and incorporating special additives into stable grouts, are now being systematically exploited in major soft ground tunnelling projects in Europe. The methodologies of jet grouting continue to be developed with special attention being paid to qa/qc issues, reducing unit production costs, and improving predictive capabilities for subsequent settlements.

Jan 1, 1993