Search Documents

By H. L. Bourne

This paper describes six basic stages between perception and production for a new sand and gravel deposit. Sand and gravel, like many of our natural resources, is taken for granted. It is assumed by John Q. Public that because sand and gravel is ubiquitous that it is available whenever and wherever needed - so long as it does not have to be mined in his neighborhood. This idea illustrates one of the enigmas of the industry, the fact that sand and gravel is abundant; however, its availability is another matter. Another problem is that this resource falls in the category of high volume, low profit materials; therefore, transportation costs are critical. Transportation roughly doubles the cost of these materials. It is not difficult to find sand and gravel, at least in Michigan. The problem is to locate a new source close to a market, near an adequate transport route (usually a highway) and in an area which will allow mining.

Jan 1, 1970

By J. Scott McDougall, J. Herman P. Eng. Vanderlaag

An underground mine fire can seriously threaten the lives of all personnel in the mine. This fact makes fire emergency planning a high priority in the mining industry. The optimum warning alarm must be fast and able to reach all miners, regardless of their location or work activity. Current means of fire warning are varied, and include such methods as stench, telephones, and word-of-mouth (messengers). Unfortunately, none of these methods are entirely satisfactory. A novel fire warning alarm which enables instantaneous warning of all underground personnel, the Canary Nine Messenger System, has been developed by VLF Magnetic Systems Inc. in conjunction with Noranda Technology Centre and the U.S. Department of the Interior - Bureau of Nines. The warning is sent by an electromagnetic signal which penetrates through mine rock to receivers housed in the battery packs which also power each miner's cap lamp. A loud buzzer in the integrated battery/receiver unit and the flashing of the cap lamp alerts miners to incoming messages. Testing of prototype equipment has demonstrated that the transmitted signal is capable of penetrating through over a mile of mine rock and activating the receiver. This report describes the theoretical basis for through-the-rock ultra-low frequency electromagnetic transmission, and the design of recently available transmitter and receivers.

Jan 1, 1995

By A. Bumanis, K. S. Bawa

INTRODUCTION A rail rapid transit system called the "Metro" system is presently under construction in the Nation's Capital area. The agency responsible for the design and construction of the Metro system is the Washington Metropolitan Area Transit Authority, an independent tristate organization set up under an Act of Congress and financed by federal, state, and local public funds supplemented by revenue bonds. When completed, the Metro system will comprise nearly 100 route miles. About fifteen percent of this mileage is now under construction, while designs for the-remainder are in progress. The system is scheduled for completion in about eight years at a cost of approximately 3 billion dollars. The Metro system will involve nearly all types of construction generally used for rapid rail transit projects. About half of the mileage will be underground, comprising approximately 16 miles of rock tunnels, 10 miles of earth tunnels, and nearly 21 miles of cut-and-cover construction in earth (see Figure 1.). The remaining 51 miles of the system is planned to be constructed on the surface as at-grade or elevated structures. The system includes 86 passenger stations, 53 of which will be underground structures. Twelve of the underground stations will be large size chambers in rock while other underground stations will be constructed in earth as cut-and-cover structures. Thus, about one-fifth of the system will be designed as underground structures, namely tunnels and stations, in rock. Such designs in rock resulted from the existence of bedrock (schistose gneiss) at reasonable depths generally in the north and northwest

Jan 1, 1997

By Koehler Stout, Leroy Friel

INTRODUCTION Hydraulic sand fills have been extensively used in the United States in deep metal mines since 1940, and hydraulic fills have been placed in coal mines in Europe for many years. Numerous surface hydraulic fills exist in Appalachia for the disposal of coal mine waste and throughout the United States for the disposal of other mining, manufacturing, city, and paper company wastes. Hydraulic fills, as they are now deposited in stopes in mines, are often deposited at near minimum density and hence provide very little support to stope walls and pillars. If the support strength of fills could be increased, perhaps ground conditions in deep mines could be improved making them safer and more efficient. Surface fills deposited at higher densities could be covered with top soil upon which grass could be planted. The purpose of this paper is to describe procedures where the support strength of hydraulic fills can be considerably increased, and the focus of the paper is on applications to deep mines. In deep mines the objective of increased fill strength is to reduce heavy ground problems, improve destressing techniques, reduce or eliminate rock burst incidences, provide better working conditions, provide wall support so that more or all ore pillars can be removed, and improve mine safety, efficiency, and reduce surface environmental problems. The authors have shown that it is possible to improve fill strength used in deep mines. This paper reports the slurry filling procedure, fill testing techniques, and some recommendations for application in deep mines. Some of the reasons for low strength hydraulic fills are:

Jan 1, 1979

By A. T. Yu

As a nation, we have been known as perhaps the most wasteful in history. From the perspective of engineers and builders on the other hand, planned obsolescence and demolition did beneficially pave way for growth and provided environment for new businesses. Recent economic recession and intense competition from overseas, however, have drastically changed the economics. The high cost of capital and the demise of indiscriminate plant expansion have totally altered the way we conduct our business and run our operations. As a response to increasing demands for better efficiency with little or no funding available, everyone is forced to make do and do better with whatever little he has. Today it nay not be an exaggeration to state that modification of existing facilities may have finally emerged as a way of life. This paper will outline examples of how several companies have effectively modified existing facilities to do more and do it efficiently without having to demolish everything and/or to spend a fortune.

Jan 1, 1985

By Stanislaw Wasilewski, Zdzislaw Krzystanek, Boleslaw Firganek

The experimental system for mine venti1ation control in Staszic colliery has two - level structure. In the lower - measuring 1evel the existing computer - based early fire detection system has been used completed with a number of additional sensors needed for ventilation parameters monitoring. The higher 1evel is a secondary computer equipped with a suitab1e dedicated software performing data processing according to the control a1gorithm. Direct control of air flow in a selected mine district is performed by means of a remotely controlled automatic regulator. Apart from functional tests of the system and its elements some research work has been carrying out in the colliery based on observations of transient effects caused by changes in air flow distribution.

Jan 1, 1989

By Jaye Pickarts, Bret Boster, Jack McPartland

Pegasus Minera de Chile, Ltda. is completing three phases of metallurgical evaluation on the Pullalli project to develop a preliminary process flowsheet. A project feasibility study is in progress. The feasibility study includes a proposed process flowsheet designed based on results from the multiple stages of metallurgical evaluation. Phases I and II of metallurgical evaluation included laboratory scale heap leach and milling cyanidation testwork on multiple drill core composites and bulk ore samples from the Pullalli Project. Phase Ill included pilot scale milling/cyanidation testwork on Pullalli drill core composites. The proposed flowsheet includes selective mining and separate processing of low grade and high grade ores. Low grade ore will be crushed and heap leached. High grade ore will be milled leached for 12 hours in an agitated cyanidation circuit. After 12 hours of leaching, sands and slimes will be separated and the sands will be washed using a counter current cyclone (CCC) circuit. Partially leached and washed sands will be added to the crushed low grade ore for heap leaching treatment and permanent placement. Partially leached slimes will be thickened in a high capacity thickener and will be processed in a CIP circuit. Leached slimes will be placed in a tailings impoundment.

Jan 1, 1996

By Sean E. Armstrong, Deepak Malhotra

Gold extraction from refractory ores as a percentage of total gold production is increasing. The processing technology options for treating difficult-to-process refractory ores are also increasing. The best processing option is dependent on many factors including feed grade and the cause for ore refractoriness. The causes for ore refractoriness are many foldCpreg-rob­bing, encapsulation in pyrite, arsenopyrite or silica, presence of cyanocides, presence of cyanide-insoluble gold compounds, etc.1. The first step in the process development of a refractory gold deposit is to determine the cause for ore refractoriness. The traditional approach of undertaking detailed mineralogical examination of ore types, major and minor mineral constituents and their association does not necessarily provide the metallur­gist all the information needed for characterization of gold-bear­ing ores. For process development programs it is desirable to complement traditional mineralogical methods with diagnostic leach testing, which attempts to quantify the deportation of gold in various mineral matrices. This paper briefly reviews the diagnostic leaching proce­dures and its applications for a wide range of gold-bearing refractory ores, both primary and by-product.

Jan 1, 1996

By F. W. DeVries

The preoccupation with cyanide as an environmental issue has been described as virtually an obsession for state and federal agencies enacting regulations for environmental protection. This seems likely to continue in legislative planning, as well. This is despite the fact that the only significant group of cyanide-related incidents has been the bird-mortality occurrences, predominantly in arid areas, and these have been greatly reduced by a concerted effort by operators. What follows is a brief list of areas for which the industry may need either additional information or plans for defensive strategies over the next two to five years.

Jan 1, 1991

By L. B. Hales

Color video or digital cameras have been installed over flotation cells to monitor color, bubble size, froth movement, and other characteristics. These systems are designed so that the camera provides flotation performance information just as any other sensor might. Factorial tests have been run to monitor and measure the variation in froth characteristics as a function of flotation control settings. Ultimately, it is envisioned that froth image sensors can be used to monitor and control the flotation performance as effectively and for less cost than current analytical systems.

Jan 1, 1999

By Osamu Shoji, Mamoru Kato

In order to continue improving the quality of telecommunication services to meet the expectations of the people and to increase reliability in the case of emergency such as disasters, Nippon Telegraph and Telephone Public Corporation (NTT) is now constructing cable tunnels which connect main urban telephone offices. However, almost all the large cities in Japan are built in river deltas, so that their chief underground features are low strength fluvial deposit and a high ground water level. In this saturated soft ground, the ground surface at an installation site has occasionally subsided through deep excavations for cable tunneling construction. As these settlements have sometimes caused accidents, especially in densely populated large cities, NTT has made much effort to avoid such accidents. These accidents have occured mainly in flexible sheeting due to its inward movement. Therefore, after the investigation into forecast method of sheeting deflection with accuracy, NTT has reserched a system which forecasts ground surface settlements. This paper describes an outline of the ground settlement forecast system and practical example on the site.

Jan 1, 1979

By John A. Shuster

Case histories are reported for several soft ground shafts ranging from 6' to 40' in diameter and 50' to 230' in overburden depth for which ground freezing was employed to provide temporary ground support and groundwater control during shaft sinking through the overburden. Cases reported emphasize dealing with difficult site and ground conditions such as working within existing buildings, through very soft, running and bouldery soils, in the presence of substantial lateral groundwater flows, and into salt dome deposits requiring special considerations. Construction procedures, schedule, and relative costs are discussed for each case.

Jan 1, 1985

By M. B. Mooiman

Cyanidation of gold and silver ores by conventional mining and milling techniques has been practiced for over a century. During the past decade, heap leaching has emerged as a viable process for treating certain gold and silver ores. (1) The rapid development of heap leaching for gold and silver ores is largely a result of lower capital and operating costs and faster start-up time than that offered by conventional mining and milling. In general, these features make heap leaching an ideal approach for exploiting either small or large low-grade disseminated deposits of gold and silver considered to be uneconomic by conventional methods. The development of heap leaching technology has evolved from the operations initiated in the western United States. The basic components of a typical heap leaching operation are depicted in Figure 1. Run-of-mine or crushed ore (usually 1 to 5 ppm gold) is delivered to specifically prepared impervious pads. Alkaline cyanide solution is applied to the surface of the heap and allowed to percolate through the heap (typically 10-30 ft high). Pregnant leach solution which drains from the heap is collected and stored in tanks of sufficient size or in collection reservoirs. Gold and silver are recovered from the pregnant solution and the barren solution is recirculated back to the heaps after reagent make-up.

Jan 1, 1983

By James M. Reichman

Waterjet assist of mechanical cutters has been demonstrated in a variety of laboratory studies as well as on field equipment. As this technique becomes more widely accepted, it will be necessary to develop methods of minimizing the horsepower and water requirements. In machines such as roadheaders, continuous miners, and longwall shearers, the use of waterjet assist can be optimized through the development of phasing valves. Phasing valves will allow only the cutters in contact with the rock to be assisted. Since only 30 - 40% of the cutters are in contact with the rock, the saving power is significant. Flow Industries has developed a phasing system for use on roadheading machines. This system allows the operator extensive control of the angle of assist as well as the quadrant being assisted. This system could be greatly simplified for production machines and adapted for use in continuous miners and longwall machines.

Jan 1, 1985

By K. Tokutake

Kobe Steel, Ltd. improved the quality of iron ore pellets for blast furnace burdens when it enlarged its blast furnaces. However. there still remained room to increase reducibility at high temperatures for better blast furnace operation. In particular, it was still necessary to lessen the reduction retardation above 1200?C. In the last few years, by employing iron ore and additives of optimum size structure, large pore pellets with a high porosity have been obtained. By using this method. Kobe Steel. Ltd. has accomplished the technology to produce pellets with remarkably high reducibility.

Jan 1, 1989

By E. Topuz

Mining equipment, like all other equipment, is subject to failure. Since most failures occur at random and are unexpected, corrective maintenance is usually more expensive and causes more down-time than preventive maintenance. In order to reduce the number of failures and thereby increase the availability of an equipment or system, preventive maintenance can be scheduled at predetermined points of time. The preventive maintenance scheduling policies presented in this paper utilize reliability and probability theories. They can be applied to various production bottlenecks where high cost equipment precludes having sufficient quantities of stand-by units.

Jan 1, 1982

By James J. Fallen

In this paper we are going to look at some things that may happen to the industrial minerals industry in the next decade. First, some concepts and definitions. What are industrial minerals? Not everyone agrees on an answer to this. So let's look at some of the opinions. Some say that industrial minerals are non-metallic minerals. As you well know, metallic minerals are used as a source material for metals. Copper, lead, and zinc are extracted from metallic minerals. But, some metallic minerals are also used for other reasons. Bauxite is used as a source of alumina and aluminum. It is also used as proppant in well drilling, as an abrasive, as a refractory material, and as a source of aluminum-based chemicals. So bauxite is both metallic and nonmetallic. There are other examples, too. Bastnasite is a source of rare earth metals and alloys but its concentrate is used in fluid cracking catalysts. Phosphate rock is an industrial mineral when used for fertilizer, but it is also the source of phosphorus. Ilmenite and rutile are sources for titanium dioxide pigments as well as titanium. So the nonmetallic designation is not adequate to define industrial minerals. Some say industrial minerals are called such because they are consumed in industry. How about your cat's litter box? Is that industry? Huge amounts of montmorillonite, attapulgite and other sorbtive minerals are pelletized and calcined to make animal litter. Doctors are trying to get people to cut down on their salt consumption. They are against people eating industrial minerals. When diamonds are a girl's best friend, they are not industrial minerals; when they are grinding and polishing media, they are. These examples show that industrial minerals are not exclusive to industry. Regardless, here is my list of industrial minerals: Abrasive Materials - Bentonite Antimony (Oxide) - Borates Asbestos - Calcium Carbonate Attapulgite - Diatomite Ball Clay - Dolomite Barite - Feldspar Bauxite (and Alumina) - Fire Clay Fluorspar - Pyrophyllite Fuller's Earth - Rare Earths Graphite - Salt Gypsum - Sand and Gravel Kaolin - Silica Sand Kyanite - Soda Ash Limestone - Sodium Sulfate Magnesite - Spodumene (Lithium) Magnetite - Sulfur Mica - Talc Nepheline Syenite - Titanium Dioxide Perlite - Vermiculite Phosphates - Wollastonite Potash - Zeolites Pumice There is some overlapping. Fuller's Earth takes in some attapulgite, bentonite, and other minerals, depending on the market. Some would like to distinguish industrial minerals by the market emphasis they receive compared to fuels, metallics, and precious metals. But even there, strict logic fails. Some industrial minerals are commodities. They are sold on a price basis against industry product specs, usually in large volumes. Phosphate rock, potash, sulfur, salt, soda ash, and other materials fit this category. Some are almost custom-designed for end-use and meet performance specs. These are sometimes called functional or specialty industrial minerals. Examples of these are ground calcium carbonate, water-washed kaolin, cosmetic grade talc, filtration grades of diatomite, perlite, and vermiculite. To determine prospects for the decade ahead, regardless of our

Jan 8, 1984

By J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m (36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM -800 Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

By R. S. Mateer

Linear programming on desktop computers is commonly used to optimize coal blending proportions. The objective function is usually the cost of the blend. The constraints consist of materials and heat balances as expressed as linear functions of the blend. This is illustrated in Example 1. Inclusion of a sulfur compliance constraint in more complex because the maximum permitted sulfur percentage is not a pre-specified constant. Rather, it is a function of the calorific power of the blend itself. The current limit of 1.2 pounds of sulfur dioxide per million Btu may be expressed as: [Sulfur Max%= 0.6 . Hl10,OOO with H in Btu/lb.] A proper constraint equation may be formed by defining for each coal a function that is the difference between the actual sulfur percentage and the maximum sulfur percentage. This may be regarded us an excess sulfur percentage. For Coal A of Example 1. this would be: [ Sulfur Excess%=0.5-0.6 13,000/10,000=-0.28] This value would be used as the coefficient of the weight proportions of this coal in the blend. The complete constraint equation would then be the sum of such terms for each coal set less than or equal to zero. This is illustrated in Example II. [ ]

Jan 1, 1995

By K. Hansson, A. Jedborn

Background In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore, from a system's point of view, slurry transporta¬tion would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alterna¬tive examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasi¬biliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. l . The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then tempo¬rarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situ¬ations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe¬line, and personnel are needed. In a first phase (Fig. 2), a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1989