Search Documents

By Christopher Mark

Sixty years ago, underground coal mining was the most hazardous job in the United States. Roof falls killed about 100 miners every year, more than all other causes put together. Fast forward half a century to 2016, and the first year ever with zero roof fall fatalities. Just three miners were killed by roof falls during the following six years. To understand how this historic goal was achieved, this study analyzed hundreds of roof fall fatality reports covering five decades. It found that the immediate effect of the Federal Coal Mine Health and Safety Act of 1969 (Coal Act) was to reduce the riskiest activities, like needlessly going under unsupported roof. Other hazards, like large roof falls, required technological developments before they were brought under control. Roof control plans, which the U.S. Bureau of Mines had been advocating since the 1920s, fostered the necessary improvements in both the safety culture and the mining technology.

Jun 1, 2024

"The use of gas, temperature and airflow sensors to monitor mine ventilation atmospheres offers numerous safety and operational bene-fits to mines. Detection of dangerous gases, changes to airflows and temperature variations are some of the obvious benefits of using at-mospheric sensors in mines. The prediction of atmospheric conditions between sensors however is potentially difficult, and gaining full cover-age a mine will require either many sensors or a method of extrapolat-ing and predicting atmospheric conditions between and downstream from a sparser array of sensors. A dynamic simulation computer model technique is demonstrated to predict time based changes to atmosphere conditions downstream from sensors. The dynamic model predicts the time based changes to conditions throughout a mine model by simulating the mixing, addition and dilution of gases and airflow changes in incremental time steps. The advantages of this method is that a real time overview of full mine atmospheric conditions can be viewed at all locations, even areas without sensors. In addition, with careful planning and consideration of potential contaminant sources, the number of required sensors can be minimized. INTRODUCTIONMine Ventilation Sensors The importance of continuously monitoring mine atmospheres has been recognised since mining underground began and the effects of harmful gases on human health were discovered. Through the 19th and early 20th centuries, coal miners would take canaries underground with them as an early detection system against life threatening gases such as carbon dioxide, carbon monoxide and methane (Figure 1). The canary, normally a very songful bird, would become agitated, stop singing and eventually die if not removed from these gases, signalling the miners to quickly exit the mine (Davalle, 2011)."

Jan 1, 2016

By J. D. Patsey, G. T. Lineberry

A.E. Hall The authors are to be commended for their attempt to provide a convenient piece of software for preliminary drum hoist specification. This field has received little attention in recent years and is eminently suited to calculation by computer. Unfortunately, there appears to be an error in the calculation of the required rope diameter. The 66-mm (2 5/8-in.) rope selected is oversized for this application. Wire rope weight and breaking strength are related to the rope diameter. For a round strand rope

Jan 8, 1987

By C. Flores, L. G. Twidwell, T. S. Jordan

It is well known that manguniferous silver ores containing manganese intimate) associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily to the recovery of copper from oxidized and oxide-sulfide ores. A new alternative process, consisting of segregation roasting followed by flotation to recover the silver from refractory manganiferous silver ores, was studied using a 23-factorial experimental design. Laboratory investigations were conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/t silver. The investigation was designed to study the effects of the addition of salts, coke and copper (11) oxide on silver recovery. The results indicated that 79.3% of the silver can be recovered in the absence of copper oxide and 88.4% of the silver can be recovered with a copper oxide content of 1.5% at 750°C, 2% salt (NaCI). 1 % coke and 30 min of roasting. It was concluded that the addition of copper oxide improves silver recovery.

Jan 1, 1996

By M. Cai

Transformation of the measured borehole deformations induced by stress relief relies on the traditional assumption that the rock is continuous and homogeneous. Systematic and quantitative tests were carried out to check the performance of devices commonly used for measuring borehole deformations within different types of discontinuous rock conditions. Test results provide a reliable basis for considering the influence of discontinuities on in situ stress measurement and for choosing the best measuring device for a given rock type and condition.

Jan 1, 1998

By Victor F. Hollister

This first section of case histories of mineral discoveries, Vol. 3, covers some of the milestones in porphyry copper and skam exploration successes. It was during the era of these discoveries that large, complex exploration departments emerged as permanent adjuncts of large mining companies. The discoveries helped shape how and where exploration activity was conducted. Probably the most important factor in exploration success is management. Few management people are mentioned in this section or in any exploration history, yet the distinction between success and failure ultimately rested with the decisions they made. One of the most successful groups was initiated by Roger Straus and Herbert Brownell when they sought to make Asarco into an important metal producer. Relying on Clem Pollock and L.H. (Bill) Hart to identify and push worthwhile projects, the Asarco management remade the company. Asarco will benefit from exploration successes com- pounded by that team for years to come. Duval is an example of a management that decided to add metal production to its industrial minerals output. When Page Morris was president, that company opened three major porphyry copper mines and became an important factor in metals. Under the Monis management team, Duval became a leader in exploration. At the other end of the scale are managements that snatched defeat from the jaws of victory and by so doing changed the character of their companies in other ways.

Jan 1, 1991

By Fred H. Seymour

In spite of the progress made by geostatistical theory over the years, evaluation of low grade open pit gold deposits continues to be challenging. Many Carlin type deposits are modelled from exploration drilling spaced on 10C foot centers. From these drill holes, 50 by 50 by 20 foot blocks containing about 4000 tons of material are estimated. The block size is a compromise between being large enough for a good geostatistical estimation and being small enough for practical pit limit analysis and mine planning. Most of these gold deposits are highly variable and include ore and waste zones that are too small to be properly defined from exploration drilling information. Because of this, selective mining is controlled by sampling closely spaced blast holes where the density can be as high as 50 blast holes per exploration drill hole intercept. Figure 1 illustrates an example of the ore/waste contact definition before and after blast hole sampling. With exploration information only, a tentative ore/waste contact can be drawn between the exploration blocks.

Jan 1, 1989

By S. K. Singh, J. Shepherd

Feather-edging, a major source of injury and fatal accidents in Australia, South Africa and the United States, refers to a phenomenon in which the roof at the goaf edge falls, often suddenly, as a thin wafer of rock that overrides conventional timber breaker lines. The fall may adversely affect a working bord at a distance of 15 m (50ft) or more from the goaf edge. Feather-edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a test in which a concentrated row of fully grouted bolts were used to prevent feather-edging in an Australian pillar- ("total-") extraction coal mine. The test demonstrated that the bolts could resist feather-edging.

Jan 1, 2000

By Scott W. Harrison, Richard E. Aaseng

In 1993 Ispat Inland Mining Company began mining its Laurentian ore reserve, which has six distinct ore types that are extremely variable. Initially batch processing was necessary to optimize mining equipment utilization. The variability as found in the ground was compensated for in plant operation, which proved ineffective. When the last of the six ore types was introduced in 1997, production, quality, and cost were seriously impacted. In-pit blending was the solution developed by the process management team to provide the plant feed required to economically process all six ore types in the Laurentian reserve.

Jan 1, 2000

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Mine explosions are one of the most concerning risks related to underground coal mining, as a single gas explosion can cause injuries and fatalities among miners. Underground infrastructure seals and build-in-place (BIP) refuge alternatives (RAs) are employed to isolate an area from active workings to mitigate coal mining-related accident risks. They are designed to withstand blast pressures from a possible accidental detonation of the contained gas or a coal dust explosion. Crosscut seals and BIP RAs, typically consisting of steel-reinforced concrete, are prone to strong convergence and have a significant leakage potential due to high convergence damage near mined-out areas. The roof-to-floor convergence can change the structural integrity of these structures, and altered structural integrity can lead to less explosion resistance capability. Hence, a thorough analysis is needed to further understand their explosion response under various strata conditions.

Jul 1, 2023

By Donald J. Donahue

Ladies and Gentlemen: As we begin these three crowded days of technical and economic discussion of problems faced by mining and metallurgical engineers, it seems appropriate at this Keynote Session to consider the future of this industry from which we derive our livelihood, It is also appropriate at this international meeting to view our industry on a world-wide basis. First, let us assess the world's future needs for minerals - the needs which it is our industry's task to meet. Next, let us look at what supplies of minerals may be available to meet those needs. I will speak of this first in terms of the physical availabilities of minerals. Finally, we can consider some of the social or institutional factors which will condition the world's mining industry as it goes about its task of discovering, developing, producing, and delivering the minerals needed to meet the world's demands. Let me give you a foretaste of my conclusions. First, future world demands upon our industry will be enormous, eclipsing anything that we have known up to this point. Second, there is strong evidence that our earth's crust contains a sufficient physical quantity and variety of minerals to meet forthcoming needs for as long a period ahead as one can envisage.

Jan 1, 1974

By Justine Ealy, Daniel Yang, Christina Foster

Maintaining stable high walls can be a challenging task. Complex geological and structural features, alteration zones, rock mass properties, and hydrogeological conditions must be well understood to design a safe mining environment. Economic considerations must also be taken into account as the mine operator must provide ore deliveries and protect reserves. However, even when good engineering practices are followed, and proper blasting and mining techniques are implemented, slope movements may still occur. When these slope instabilities are minor, the mine is often able to continue operations with minimal impacts on safety or production. When these occurrences are excessive and coupled with high rates of movement, a robust monitoring system is crucial to continuing mining activities while protecting personnel. This paper summarizes the approach an open pit mine in Nevada took as excessive and rapid high-wall movement was experienced in an integral area. Creative mining approaches, combined with slope monitoring radar technology, were utilized to maintain safe and successful mining activities despite active movement that exceeded an average velocity of 30 inches per day.

Feb 1, 2024

By Justus B. Deen, Randy Peterson

INTRODUCTION The General Chemical Soda Ash Operation located near Green River, Wyoming produces about 4.5 Mt of trona per year. In July 1989, Mine Ventilation Services Inc. performed a ventilation survey of this complex trona mine which had thirteen active panels spread over 36 square kilometers. The ventilation survey and subsequent study showed that the intake shaft air velocities were at their practical limits (Wallace and Rogers, 1987). The need for additional intake capacity was immediate. The ventilation network modeling delineated the best location for this new intake shaft as it applied to the 5 year ventilation plan. Unfortunately, this location, 6.5 kilometers from the soda ash processing plant, would make heating this intake air very costly. Presently, the intake air is heated by heat exchangers which use waste heat from the plant. Air heating during the winter months is necessary for miner comfort and to prevent potential freezing of water lines in the mine. It was decided to examine the feasibility of heating the air geothermally by coursing it through an old production panel. This method of air heating has been used in this region with good results at the Stauffer Chemical Operation (now Rhone-Poulenc) (Moore, 1985). In 1990, a geothermal heating study examined four different production shaft/panel configurations and a workable design was found. The operators at the General Chemical Soda Ash Operations acted on this design and began raise boring a ventilation shaft in the Spring of 1991. This paper describes the ventilation system, briefly, and the geothermal heating studies performed. Findings of the 1990 geothermal studies are then compared to field data acquired in the Winter of 1992. THE VENTILATION SYSTEM The ventilation system at General Chemical had four shafts serving the mining horizon in July 1989; three of these shafts are located at the Northwest end of the mine. The active work areas had progressed to the South over the past years and supplying ventilation has become increasingly difficult. The 6.1 meter diameter #3 Production shaft and the men and materials compartment of the 6.1 meter diameter #2 Split Shaft had reached their air velocity limits. Conversely, the 4.6 meter diameter #5 Exhaust Shaft was under utilized. Ventilation studies showed the conversion of the 3.7 meter diameter #1 Exhaust Shaft to an intake would provide adequate intake capacity for two years. The next option to improve ventilation was the addition of an intake shaft at the southeast part of the mine at the intersection of H Mains South(H-M-S)and J Mains East(J-M-E) (See Figure 1). A service shaft has been planned for the extreme Southeast end in the late 1990's. Ventilation network analyses showed this interim intake shaft would have to be at least 2.5 meters in diameter to postpone the service shaft construction beyond 1995. The greater the size of the borehole, the further the construction could be postponed. In October 1991, General Chemical commissioned the 4.57 meter diameter #4 Ventilation Shaft near the junction of H-M-S and J-M-E as shown in Figure 1. The L95 panel would be used for air heating as described in the geothermal heating section to follow. GEOTHERMAL STUDIES Geothermal heating studies were performed by MVS Inc. in May 1990. Using a modified code of CLIMSIM, an underground mine climatic simulation model, several different shaft/panel configurations were examined to see which would provide adequate air heating during the winter months. CLIMSIM simulates heat flow into a single underground airway. The program was used to evaluate the heat flow to and from the airway surface and to calculate the resulting change in dry bulb temperature of the ventilating air. CLIMSIM uses inlet air conditions, airway characteristics, and rock thermal properties input by the user to predict the variation of psychrometric and thermodynamic parameters along an underground airway.

Jan 1, 1993

By S. K. Mishra, S. B. Kanungo, D. Biswal

Jigging of the -2.8 +0.7-mm size fraction of a friable, low-grade manganese ore sample from Andhra Pradesh increased the Mn content of a concentrate by 7% to 8%, with an average recovery of 57%. The jig concentrate was mixed with the unjigged -0.7-mm size fraction and ground to -150 µm. The sample was then subjected to wet high-intensity magnetic separation (WHIMS). The magnetic fraction thus obtained showed an increase in Mn content of 6%, but with an overall recovery of only 50%. The results of hydrocyclone classification of -150- µm ground ore indicated that the method is not capable of upgrading the manganese content, as both ferromanganese oxides and aluminosilicate gangue minerals constitute the fine size fraction. However, when the nonmagnetic fraction obtained from the WHIMS of -150- µm ore is subjected to hydrocyclone classification and the underflow obtained is subjected to WHIMS again, an overall recovery of about 50% to 52% is obtained with at least a 7% to 8% increase in the Mn content of the product. The phosphorus content in the product is not reduced by either of the two combinations of methods. The complex association of phosphorus with all the major phases in the ore has been clearly demonstrated from the linear correlation between the distribution ratios of major constituent phases and phosphorus.

Jan 1, 2000

By Steve Lloyd, Mary Anne Antonioli, Byron Darnton

Pegasus Gold Corporations' Montana Tunnels mine began oper­ation in March 1987. The process plant at startup consisted of a bulk flotation circuit followed by leaching of the reground bulk concentrate. The leach residue then advanced to selective Pb/Zn flotation. This original circuit had its share of problems, and the leach circuit was abandoned after six months. The bulk flotation circuit was modified to selective Pb/Zn flotation at this same time. Gravity concentration was researched early on, prior to selecting bulk flotation with leach as the flowsheet of choice. Flotation was deemed to be more practical than gravity due to the lower capital and operating costs. No further work was done concerning gravity concentration until 1990 when it was decid­ed to investigate ways to diminish the occurrence of free gold reporting to the flotation tailings.

Jan 1, 1996

By Jim Avraamides

Historically, much of Western Australia's gold production has come from the refractory sulphide-telluride ores located in Kalgoorlie's Golden Mile. Most of the recent gold boom has been associated with low grade, open pit free-milling oxide deposits. Primary sulphides are commonly encountered at depth and in many cases are highly refractory. Different approaches to the problem of recovering go1d from these ores have been adopted subject to local conditions both technical and environmental. The least preferred option is the preparation of a gold- rich flotation concentrate which is shipped to a smelter. Roasting of flotation concentrates can be practised in certain remote locations where sulphur emissions are tolerated. Fine grinding of flotation concentrates followed by direct cyanidation is another popular approach although this often leads to fouling of carbon by flotation reagents in the adsorption section and high soluble gold losses.

Jan 1, 1989

By Joseph W. Kupfner

It is a recognized fact that a good maintenance program is a pre-requisite for minimum delay costs and maximum availability of equipment. To develop such a program and to make it effective, one must establish detailed instructions pertaining to inspections, lubrication, servicing, and/or replacing of various parts. A schedule must also be established for these maintenance checks, whether they be weekly, monthly, or whatever period is essential for the equipment. The number of tasks to be performed becomes monumental, and the administration is beyond error-free human capacity. It is for this reason that the computer must be an essential element in any efficient and economical preventive maintenance program. The evolution of a computerized maintenance program began some 18 years ago in the Mining Division of USSteel. It started with a manual system of preparing cards containing preventive maintenance instructions that had to be performed on some regular basis. We were very quickly overtaken by the massive task of administration and distribution of instruction cards to the users. The task became insurmountable as more mines were added to the system, mines that were spread over a large geographic area. It also became evident that the ability to make changes in equipment assignments and in the "what to do" instructions would require more time than had been anticipated.

Jan 1, 1986

By O. E. Brown

The measurement principle of the Coulter Counter for particle size analyses is described. The application of the Coulter Counter to cement particle content and size analysis and to the size distribution of clinker from standard grindability tests are described. Methods of calibration, sample preparation and data reduction are presented. The results of the analyses obtained are compared with characteristics associated with performance showing both concordance and non-concordance of test data., Future uses of the Coulter Counter for particle size analysis in research and plant control adaptations are indicated.

Jan 1, 1960

By Vladimir Nikolić, Alex Doll

The Bond ball mill grindability test is one of the most common metrics used in the mining industry for ore hardness measurements. The test is an important part of the Bond work index methodology for designing and measuring the efficiency of mineral grinding circuits. In spite of being called “Bond’s Law,” the work index equations are not a law of nature; but rather an empirically measured regression of a large data set collected by the Allis- Chalmers corporation in the period between 1930 and 1952. As a regression, it is valid within a specific “calibration space,” and great care is required when deviating the test procedures or observing results that are outside of that calibration space. This paper is a collected summary of other works by the Authors that describe feed sizes, product sizes, quality control checks, and other information about interpreting the test and using its results. Examples of adjustments that are sometimes required when using the test are: changing the test product (P80), and coping with a feed that is too fine to apply the “proper” feed preparation steps (such as is sometimes observed from HPGR or SAGDesign product testing). Related metrics, like the Morrell Mib value and Levin B value will be discussed, along with recommendations for their use on design projects. The intended audience is any user of laboratory work index test data.

Feb 1, 2024

By Andrew J. Neale, Mark Franklin, Mike Cooper

Although recent advances have significantly improved our understanding of flotation fundamentals, disturbance variables combine to make it difficult to maintain steady state operating conditions over either the short or long term. One of the major concerns relates to knowing how much reagent to add to the flotation system, how to monitor the addition rate, and how to determine when to adjust the reagent addition rate in the presence of these disturbances. This paper will look at the development and installation of process control systems that address these issues. The economic benefits that accrued from the implementation of these strategies is described.

Jan 1, 1994