Search Documents

By Siegfried Zell

Preface Pipe heading is a customary and proven technology for the underground installation of all types of piping. In over 90 % of all cases, straight pipe sections are used between shaft constructions since, e.g. this follows roadways or it is necessary from the operational aspect due to pipe control methods, e.g. to use a remote control pipe sensor or comparable control devices within sight from shaft to shaft. Frequently, a straight pipeline is impossible, and is replaced by a more or less spatial alignment due to surface conditions, structures in the ground or foundations. This situation applied for the construction of the Nebensammler Neuland (intercepting sewer) in Hamburg-Neuland for sections IV and V. The following paper is not intended as a description of the complete project. It deals mainly with the special features of this pipe heading, with what I believe to be its somewhat unusual route. The task The building authority design issued by the Main Department for Urban Sewerage of the Free and Hanseatic City of Hamburg consisted of the construction of the collector by a pipe heading using NW 1300 pipes in 2 heading sections. One short straight and one long

Jan 1, 1989

By D. L. Purcell, B. T. McClure, J. McDonald

The U.S. Bureau of Mines has completed a laboratory evaluation of exhaust emissions from a diesel engine using an oxygenated diesel fuel. The fuels tested were soy methyl esters in a neat (100%) form and low sulfur, petroleum number 2 diesel fuel (D2). The engine tested was a Caterpillar 3304, indirect injection, naturally aspirated, 75 kW, diesel engine that is typical of engines used in underground mining applications. The objective was to determine the extent to which oxygenated fuels, such as methyl esters, reduce diesel particulate matter (DPM), and their influence on upon gaseous emissions such as total hydrocarbons, CO, NOx, NO2, formaldehyde, and other exhaust emissions. Heavy- and light-duty transient tests were used to simulate load cycles typical of mine applications. The soy methyl ester fuel produced greater amounts of volatile DPM (organic material) but much less nonvolatile DPM (carbon soot) for overall DPM reductions. A diesel oxidation catalyst (DOC) typical of the type commonly used in metal and nonmetal mines was tested with both fuels. The DOC further reduced the volatile and total DPM when used with the soy methyl esters, but increased the total DPM for D2 due to sulfate formation. The soy methyl ester fuel reduced CO and hydrocarbon, and NOx emissions. The DOC further reduced CO and hydrocarbon emissions.

Jan 1, 1995

This paper reviews the historical literature and the author's experience with regard to the effect that the selection of grinding ball size or sizes has on ball mill grinding efficiency. The conclusions presented provide guidelines for single and multi-size charging prac- tices in commercial milling operations.

Jan 1, 1998

By B. K. Parekh, W. M. Goldberger

Sludge obtained during the production of magnesium (Mg) from molten MgCl2 by electrolysis contains entrapped magnesium particles. The sludge containing the magnesium particles is a friable, continuous matrix of frozen salts that may also contain some oxides and impurities. Due to the high reactivity of magnesium metal with water, a dry process was developed to recover magnesium metal from the sludge. The process utilizes mineral-processing unit operations. The steps include selective comminution, screening, attritioning and tabling. Recovery of the high-grade (>90%) metal was in the 70% range. The novel process was also successfully applied to a magnesium-alloy for the recovery of metal from the sludges.

Jan 1, 1997

By N. L. Wesis

General History The first jaw crusher in the US was patented about 1830, but the Blake crusher that has maintained a substantial advantage over other types was invented in 1858 by Eli Whitney Blake. For going on 150 years the jaw crusher has been an invaluable machine; even today, when gyratory crushers have assumed most of the burden of crushing large tonnages of large rock and ore, the jaw crusher has a firm place in the mining industry. It is interesting that soon after the invention of the Philetius Gates gyratory crusher in 1881, a contest between the first No. 2 Gates and Blake jaw crushers of equal gape showed the gyratory to be 3.2 times as fast. This foretold a day not far in the future when the jaw crusher would not be adequate on the largest jobs. In his Textbook of Ore Dressing (1909) R. H. Richards recom¬mended that the word breaker be used for all machines breaking to relatively large sizes (say to 5 in. or greater), and crusher be used for finer work. Even in the 1968 US Bureau of Mines dictionary of mining terms the work breaker is defined by Richards in this context. However, in modern US usage it is nearly limited to coal breaking. Over the years the jaw crusher has been developed in a variety of forms but it appears today in these three general forms: (I) Blake type, (2) Dodge type, and (3) single toggle (or overhead eccentric) type. All of these crushers have a fixed jaw and a moving jaw, between which the coarse rock fragments are intermittently caught and crushed. The three types are differentiated by the manner in which the movable jaw is moved in relation to the fixed. Types The Blake-type crusher is shown in cross section in Fig. 1. The simplicity and strength that have made it first among jaw crushers are evident. The movable jaw is suspended from a cross-shaft at its upper end, this shaft being carried in bearings on the sides of the frame. The actuating mechanism consists of an eccentric shaft, also supported in frame-mounted bearings, which imparts through a pit¬ man and a pair of toggles a reciprocating motion to the bottom of the swing jaw, the return movement being effected by several spring¬loaded rods. The whole is built into a box frame with the crushing chamber at one end. As in all jaw crushers, the eccentric shaft is equipped with a heavy flywheel that maintains an even speed through¬out each stroke. The Dodge-type crusher illustrated in Fig. 2 is simple, mechani¬cally. Its movable jaw, being pivoted below the discharge opening, has minimum movement at crusher discharge and maximum at crusher feed. Because the choke point coincides with the point of least motion, these crushers are of relatively low capacity, and the rapid action in the feed area gives the machine the advantages of large reduction ratio and closely sized product. Thus, it fits well into low-capacity operations like sample reduction. Besides low capacity, its principal disadvantages are tendency to pack and make fines. The single-toggle or overhead-eccentric type of jaw crusher (see Fig. 3) has gained in usage, starting as a modification of the Dodge idea in that the greatest movement of the movable jaw occurs at the top, and being gradually improved and strengthened to its position today where it covers just as wide a field of application as the Blake type from the standpoint of feed opening. The motion of the movable jaw is the result of the circular motion of the eccentric shaft at the top of the swing jaw combined with the rocking action imparted to the bottom by the inclined toggle plate. Because of light weight and mechanical simplicity, it is economical in small mills and portable plants where the rock is not as tough and abrasive as to punish the machine with excessive impact from shocks, or excessive wear result¬ing from the pronounced vertical component of motion.

Jan 1, 1985

By Wilbur I. Duvall

This paper discusses general principles of underground opening design based on the concept that with the necessary input data regarding the geology of a site, the physical properties of the rocks, the in situ stress field in the rock and the general geometry of the underground openings, the rock formation can be classified into six major categories which are useful for design purposes. Using simple theories for the criteria of failure for rock In compression and tension, general elastic theory for stress concentration around openings and In structures, beam theory for stability of roof rock, and elementary inelastic theory for creep phenomena, basic design techniques are outlined for the various rock classifications. The need for field evaluation of the theoretical design is stressed and some general techniques that should be used in these field evaluations are discussed. Where appropriate, the need for additional studies and research is noted.

Jan 1, 1977

By Scott G. Britton

The first section of this text delves into construction engineering techniques for successfully completing necessary underground production support projects. I will discuss alternative design concepts, installation practices, materials and material costs, completion time, and necessary labor for individual projects. The emphasis of this section is on describing each project thoroughly and providing a practical guide for the supervisor or engineer. There are four main construction categories for typical underground mining projects. These are: 1) Transportation of men and supply materials. This refers to track and wire installation and roadbed grading and ballasting. 2) Ventilation, composed of overcasts, man doors, regulators, and stoppings. 3) Drainage, including sumps, pumping stations, drainage networks, pumps, and face drainage. 4) Haulage of coal and rock from the face to the outside. The focus here is in the installation of belt lines, belt drives, transfer points, and vibrating bins/feeders. The first section shall fully discuss these four categories in regard to the construction engineer or supervisor designing, building, or improving a system. In addition, special projects such as surge bins, rotary dumps, and underground offices not classified under these categories will be discussed. For manageable purposes, I have limited the installation discussions to one or two approaches I feel have merit. The variation of installations in coal mining is endless, each with its own advantages and disadvantages. Therefore, the reader should not dismiss or restrict his thinking to only the approaches in the text. It serves as a guide only.

Jan 1, 1983

By R. L. Weigel

As Florida phosphate mining gradually moves from the Bone Valley formation to the Hawthorn formation, a greater portion of the minable deposit contains dolomitic diluents which result in lower product grades that can be detrimental to the production of phosphoric acid for fertilizer uses. One beneficiation technique found applicable to the phosphate pebble size range (3 X 16 mesh) is heavy media separation using suspensions of magnetite and ferrosilicon. As part of an ongoing investigation of dolomite removal technology, a pilot heavy media cyclone system was constructed by IMC and used in the testing of a variety of drill core composites and hulk samples. The results of these tests were used to develop a predictive model for heavy media cyclone separation based on pebble fraction assays and heavy media operating parameters. This model is currently being used in the evaluation of specific future mining areas.

Jan 1, 1984

By Nicholas Kyriazia, John P. Shubilla

A performance study of oxygen self-rescuers of varying durations from the United States and other countries was undertaken as an assessment of present worldwide technology. The apparatus were tested on a Breathing and Metabolic Simulator in the Life Support laboratories of the Bureau's Pitts- burgh Research Center. Parameters monitored during the testing were inhaled levels of C02, 02, inhaled gas temperature, and breathing resistance. The metabolic demand placed on the apparatus represented the average demand of the 50th percentile miner performing a 60-min man-test 4, as described in 30 CFR 11H. Results presented include apparatus service life and subjective comments as well as averages and peaks of monitored parameters.

Jan 1, 1986

By Leo Misagi

THE ROLE OF MANAGEMENT IN PLANT SAFETY Safe Production In plant management, safe production is an ideal. It becomes reality when: 1. Plant employees work in healthful and safe conditions. 2. Plant safety is in harmony with productivity. 3. Worker absenteeism and turnover are low-the work force is stable. Plant management must apply its talents, skills, and resources to build and maintain the foundations of safe production on a system of policies, procedures, and attitudes. It must do so by marshaling all managerial functions - staffing, direction, control, innovation, and representation-toward that goal. Ideally, a plant safety program is proactive. Management should plan and implement safety activities that are aimed at prevention. Past accidents-accomplished facts-should not be the sole guide of future actions. In other words, positive preventive measures, not the fewness of accidents are the criteria for safety production. An ideal safety program is one which is cost effective. Management should view plant safety as part of a broader program-loss control. Loss control includes prevention of fires and other accidents, unhealthful conditions, and occurrences that cause bodily injury, illness, property loss, or damage. Management evaluates the employees' productivity and safety. An effective training program aimed at loss control is the hallmark of safe production. Ideally, both labor and management should be well versed in safety. They believe in the premise that work-related injury and illness, as well as property loss and damage from fire and other accidents, are manageable and preventable. Such belief prompts them to learn more about the work process and potential hazards associated with each job. They also learn how to expect and prevent fues and other accidents, and respond to emergencies at the plant. Plant management determines which individuals or groups of employees are accountable for the following functions:

Jan 1, 1991

By Stefan Medel

As a pioneer Herrenknecht started in 2018 to automate the production of tunnel lining segments. Since then, many automation processes became state of the art. Robots cleaning and oiling the moulds, hydraulic units opening and closing them fully independently. Artificial Intelligence (AI) controls the works and ensures the quality requirements. Data management has become a massive tool from a simple data collector towards a control and optimization tool. Sensors controlling concrete maturity and supporting the precast team to optimize the concrete mix. These state of the art and new innovations will be presented in this paper.

Jun 23, 2024

By M. Gobla

"Since 1994 the Bureau of Reclamation has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has applied risk analysis methods to inactive and abandoned mines to evaluate tailings dams and flooded underground mines. Case histories of potential failure mode analysis as applied to mine impounded water illustrates what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first. INTRODUCTION Impounded water, and high water content wastes, at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (5.4 million yd3 released), the Mt Poly Tailings Dam failure in British Columbia in 2014 (5.8 million yd3 released), and the Smarco Fundao Tailings Dam failure in Brazil in 2015 (78 million yd3 released) has renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originates not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes, and flooded underground mine workings. Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984 the agency developed and began using risk analysis methods. Reclamation operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of one hundred years. Many of these facilities were constructed using engineering design and construction methods which would not be considered good practice according to present day standards. Diligent observational monitoring, detailed site investigations, and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high risk sites, significant improvements to dam safety have been achieved. BOR has also applied risk analysis to evaluate and reclaim inactive and abandoned mining and industrial sites. The application of risk analysis methods in the mining industry is not new, the methodology was transferred to the mining industry more than 15 years ago as discussed in ICOLD Bulleting 121 (ICOLD, 2001), yet failures persist. This paper is meant to convey the lessons learned from BOR’s use of risk analyses in its work on mine sites."

Jan 1, 2017

By K. S. Eric Forssberg, Lennart Ryk

The paper discusses coal utilisation in Sweden. All hard coals have to be imported from other countries. Peat from domestic sources is used as a complement. Environmental legislation and taxation on fuel and emissions are severe. This situation affects the procurement, preparation, handling and use of coal. The paper presents: • R&D projects concerning deep cleaning of thermal coal. • Handling and treatment of coal used in PFBC boilers and for blast furnace injection • Dust prevention for coal and peat briquettes. Procurement of coal emphasising quality and environmental issues.

Jan 1, 1995

By Dan Ifrim

Soft ground tunneling poses major challenges to the underground industry. Most of soft ground tunnels are in highly urbanized areas, often include limited cover, and include a strong trend of increasing diameters. Therefore, soft ground tunneling works can sometimes cause inevitable ground movements and settlements that may lead to damages to adjacent buildings, roads, structures or utilities; many of these being “lifeline” infrastructure assets. Tunneling operations, Tunnel Boring Machine (TBM) advance rates, and face pressure control can significantly increase or decrease such risks, depending on how well the TBM and operational parameters are applied to the ground conditions. Additionally, the risks of impacting existing infrastructure are heightened in many parts of North America because of cobbles and boulders. To date there is no standardized guideline that determines appropriate tunneling rates nor operator’s guidelines, to ensure safe tunnelling in soft ground. The paper analyzes tunneling records from completed soft ground tunnels to determine a relation between ground conditions, tunnel cover, TBM cutters maintenance and TBM advance rates. The records are discussed to draw several mitigation measures to be adopted during tunnelling, to reduce risks of settlements, over excavation or sinkholes.

Jun 13, 2021

By M. Z. Rashad, H. A. El-Sageer

This paper compares the covariance and multiquadric functions in some mining and geological applications. The basic principals of the two techniques are covered briefly. Similarities and dissimilarities of the covariance and multiquadric functions are discussed geometrically, mathematically and practically. A 14 km2 x 16 km2 area in Baharia Oasis, Western Desert of Egypt, was selected for a detailed comparative test. The gravity anomalies of 48 test stations were computed by using the data of 63 control stations. The results indicated that the covariance function is quite better than the multiquadric one. On the other hand, the multiquadric function is simpler in computation than the covariance, which requires precalculations such as semivariogram and covariogram. Moreover, multiquadric equations are based on geometric and physical considerations rather than covariance functions.

Jan 1, 1992

By J. E. deMasi

Over the past 12 years, Exxon Coal U.S.A., Inc. has shipped over 150 million tons of coal from two mines, Rawhide and Caballo, located in the Gillette, Wyoming, area. These mines are operated by The Carter Mining Company, a division of Exxon Coal. Shipments have moved to more than 25 electric utility plants in the west, midwest, southwest, and south. The customer plants have represented a wide variety of configurations, sizes. design criteria, emission standards, and operations in different parts of the country. We have learned a great deal about the performance of Gillette area coals in utility power plants during this period. This paper covers some of the highlights of Exxon's experience with these coals in customer plants. I will focus specifically on things mining engineers may be able to do to make the product better for the customer's use.

Jan 1, 1989

By R. G. Reddy

Chemical and structural changes occurring during the roasting of refractory gold ores were investigated. Effect of temperature on oxidation behavior of ores was analyzed using TGA, DTA and X-ray diffraction methods. The experimental results showed that the carbon in the ore has to be oxidized to a minimum value before any appreciable oxidation of sulfur occurs. Oxidation rates as a function of temperature were calculated. Optimum conditions under which a successful roasting of the refractory gold ores can be obtained are discussed.

Jan 1, 1990

By H. Zhu

Qualitative and interpretative information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system pro-vides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data.

Jan 1, 1989

By M. K. Gangal, E. D. Dainty

The paper describes the capabilities of a micro-computer-based real time data acquisition system for monitoring and control of mine environments. Applications of such a system for monitoring the ventilation and air quality of a mine is outlined. The paper discusses the results of running a monitoring system with various environmental sensors in a simulated mine environment. The sensors used in this study are: carbon monoxide (CO), carbon dioxide (C02), nitric oxide (NO), nitrogen dioxide (NO2), sulphur dioxide (SO2 ), methane (CH4 ), air flow, absolute pressure, temperature and relative humidity. A performance evaluation of the monitoring system and sensors is presented.

Jan 1, 1987

By Victor E. Archer

INTRODUCTION Man is exposed to many agents which induce mutations in germ cells and/or cancer at work, at play, and at home. In this total mix of mutagenic and carcinogenic agents, how important are radon and its daughters? Before man moved into caves and other permanent dwellings, the principal mutagenic and carcinogenic agent to which he was exposed was natural background radiation--cosmic rays, radium and potassium-40 in his food, plus gamma rays and radon from the soil and rocks. When man moved into caves, captured fire, and began to preserve and store foods, his exposure to carcinogens and mutagens took a quantum leap. Carcinogens and mutagens appear to act in the same way, that is, by altering the DNA or nuclear proteins of cells. Most mutagens are carcinogens, and vice versa, so when I say mutagens from here on, I will be referring to both. The relationship of the two is emphasized by the fact that administration of a carcinogen to a group of animals not only increases cancer rates among the exposed animals, but also among their progeny (Tomatis 1979). Environmental Mutagens Smoke from man's fires, overheated foods, and foods preserved by smoking, resulted in ingestion and inhalation of many polycyclic aromatic hydrocarbons--many of which are mutagens. Caves and houses with tight windows and doors tend to collect the radon which is constantly emanating out of soil, rocks and concrete, so man's exposure to the radon daughter component of background radiation increased several fold. Preserving food by salting or pickling with material that contained nitrites and nitrates led to increased ingestion of nitrosamines, which are potent mutagens. When his grains and other foods were stored in slightly damp rooms, fungi or mold would grow on them. Several of these fungi are now known to produce very potent mutagens. The best known of these is aflatoxin B (Ramachandra 1979). It may seem strange that a living organism would produce a mutagen. One might think that it would scramble its own genetic heritage. The reason it does not is that it produces the mutagen in an inactive form. It can be activated only by an animal's enzyme systems after being eaten. When man moved into cities, the collective smoke from wood and coal fires further increased his exposure. That particular smoke has now mostly disappeared, but has been replaced by smoke from automobiles and industry. When man moved into the age of technology, his exposure to mutagens again increased dramatically. Many mutagenic chemicals, from benzene and beta naphthylamine to a long array of pesticides and tobacco products have been added to our environment. Excess deaths from cancer are now being observed among chemists in most industrialized nations. Mutagens are even found in much of our wine, beer, and whiskey (Keller 1980). Some of the chemical mutagens were widely used in food or in other commercial products before their potential was discovered. Striking examples of this is the original butter coloring agent and the polychlorinated biphenyls that have been widely used in brake fluids and electrical transformers. Large quantities of them have been discarded or disposed of in a careless manner--in such a way that many of them have contaminated our food, our ground water and air (Landrigan 1981). In this nation, with the help of several recent laws, we were just beginning to get control of the industrial chemical mutagens. With the relaxing of these laws that is currently going on, it appears that it will be many more years before we really bring chemical mutagens under control. Many nations have yet to come to grips with this problem. On top of this massive array of chemical mutagens we have now added radiation from many artificial sources. For most of us this means medical X-ray and fallout from nuclear weapons testing. Ionizing radiation is one of the most potent mutagens, so it has caught the public eye, and its contribution cannot be ignored. Fortunately, by the time we started using radioactive materials in quantity with the Manhattan Project, we had experience with radium and X-ray (some of it bad); we knew enough radiobiology and enough about methods of radiation protection so that most nuclear laboratories have had a phenomenal record of radiation safety. Radiation is one new technology with great potential for harm that has not exhibited that potential except for a few isolated situations like that of radium dial painters, uranium miners and atomic bomb victims. Uranium miners slipped into this list almost by accident. We could have protected our uranium miners just as well as we did the workers in nuclear laboratories; but we failed to do so. Why didn't we? The reason is simple. The Atomic Energy Commission was charged with protecting the health of their workers. They did not wait for a pile of bodies before they introduced controls. Congress appropriated the money, and taxpayers were willing to pay for the protection against radiation. Miners unfortunately did not work for the Atomic Energy Commission. Although mine operators were ignorant about radiation, the key item was that in the 1950s nobody was willing to pay the extra costs of adequate ventilation to control the high levels of radon and radon daughters in uranium mines. Control was not achieved until new laws and regulations were passed which made it compulsory. BIRTH DEFECTS AND CANCER

Jan 1, 1981