Search Documents

By A. H. Summers

The La Choya mine is located 55 km south of Sonoyta in northwestern Sonora, Mexico. Mineralization is controlled by a 40 meter thick thrust fault zone which created a permeable host for the metal-bearing hydrothermal solutions. The ore body is mined by open pit using wheel loaders and truck haulage. Gold and silver are recovered from low grade ore by heap leaching followed by carbon adsorption.

Jan 1, 1997

By John W. Stevenson

At the No. 4 Mine of Jim Walter Resources in Tuscaloosa County in the North Central part of the State of Alabama, the Mary Lee and Blue Creek coal beds lay 2000 feet below the surface. The quantity of methane gas stored within the coal bed reservoir at this depth and released during development mining necessitates that each coal producing section be ventilated using large air quantities approaching 100,000 cfm. In order to meet coal contractural commitments in the early stages of mine development by installing the necessary number of continuous mining machine units and to develop the mine to projected air shaft sites, high pressure, large volume mine ventilating fans were required. This presentation discusses the installation start-up and changeover procedures when two size GAF 31.5-28-1 TLT-Babcock 3500 Horsepower fans with adjustable pitch in flight blades were put on line while phasing out two Jeffrey Mining Machine Company 8HUA 117 Fans. A graph will be presented to depict the most economic diameter shaft size under 2000 feet of cover with different air quantity requirements.

Jan 1, 1982

By P. Saunier, S. Fourmont, R. Stafford, A. Jung, J. Mlynarek

The safe and economical storage of tailings generated by modern day mining operations is possibly the single largest challenge faced by miners today. By nature, tailings are a waste product that have little to no economic value. Yet, their physical and chemical contents can pose incredible environmental hazards if not stored correctly. The variety of factors that are met when designing Tailing Storage Facilities (TSFs), means that in most cases, a low-cost solution is sought to accomplish storage, meet environmental regulations, and adhere to industry best practices. TSFs can be large dam face structures or smaller structures like retention/evaporation lined ponds. Water management is potentially the single largest factor that miners and designers must contend with when constructing a TSF. Water is a necessary component in the process of extracting ore but can be difficult and expensive to remove once it is mixed with solid tailings particles. As a result, the most common disposal of these water containing tailings, called a slurry, is to simply discharge into an embanked TSF (Vick, 1990). These structures, just like any other water retaining dam, can breach releasing contents downstream. Despite modern advancements in TSF design, there have been numerous dam failures that have resulted in tragic loss of life and ecological devastation. Most notably in the last decade, the Brumadinho and Mariana Dam disasters in Brazil killed 278 people in downstream communities when TSF dams failed in 2019 and 2015, respectively (Rotta at el., 2020). Similarly, in 2014, the Mount Polley tailings spill in British Columbia was the second largest tailings spill on record and caused extensive damage to adjacent watershed ecosystems when the TSF embankment was breached (Byrne at el., 2018). While there were indeed numerous unique and underlying factors present in each of these structural failures, a shared element in the devastation was the large-scale release of unstable liquefied tailings

Mar 2, 2022

By F. L. Pirkle

A heavy mineral deposit about 1.6 km (1 mile) in length, 0.13 km (0.08 mile) in width and averaging about 3 m (10 ft) in thickness is exposed approximately 130 km (80 miles) east of Denver, along Interstate 70, in Elbert county, CO near the town of Limon. The deposit is exposed in a geomorphic feature known locally as Titanium ridge. The dominant heavy minerals, accounting for about 70% of the total heavy-mineral suite by weight, are ilmenite, garnet and zircon. The mineralized zone appears in a series of visually interpretable facies that are stacked vertically and represent subtidal, forebeach, backbeach, washover fan and aeolian depositional environments. These paleoenvironments are analogous to depositional environments represented by a modern heavy-mineral bearing facies tract on St. Catherines Island, Ga. Thus, Titanium ridge provides evidence that heavy-mineral accumulation models for late cenozoic deposits in the Georgia and Florida coastal plains are applicable to heavy-mineral deposits of the Western Interior subsurface and, by implication, the Western Interior Seaway, extending from Mexico to the Canadian Arctic.

Jan 1, 2012

By Basilio Giurgola, Federico Bonaiuti, Norbert Fuegenschuh

The North East Boundary Tunnel (NEBT) project in Washington, D.C. requires design and construction of several SEM adits which have to be built between lateral shafts and the NEBT-TBM Tunnel. The paper describes ground improvements, the actual excavation, and also the final lining works. Schedule and sequencing restrictions provided some unique challenges which had to be considered when designing and constructing these mostly short, but essential portions of the project

Dec 1, 2022

By J. Richard Tonry

In portland cement manufacturing, the raw materials axe changed to clinker in the burning operation. Generally the rotary kiln is used for this purpose and involves many processes, including pelletizing and nodelizing. This transformation is called clinkering, and is analyzed as now generally practiced in cement making, from the raw material to the resulting clinker.

Jan 1, 1963

By W. C. Brice

Minnesota contains a major copper-nickel resource. In anticipation of requests by industry to develop this resource, the Minnesota Department Of Natural Resources has developed a computerized resource inventory and analysis system, MINESITE This extensive database is available to regulatory agencies as they evaluate mining proposals as required by law. The Resource Analysis phase of the project allows state mining policy decisions to be evaluated in terms of long-range effects on Minnesota's mining industry and environmental and land use impacts. The analysis also allows for comparison of proposed mine facility sites to a representative range of sites in terms of engineering, site characteristics, and land use and environmental impacts.

Jan 1, 1980

By James W. Cooksley

Through the early stages of metamorphism, when diffusion is the predominant mineral forming process. there is a tendency toward homogenization of rock units; but there is also zoning resulting from differing primary lithology and structure. Later stages of metamorphism, when infiltration occurs, tend to intensify zoning within the rock mass. The above concepts have been borne out in exploration of talc deposits and skarns. Initially, geologic mapping and soil sampling are directed to understanding mineralogy and petrology. Later, seismic methods are employed to further define lithology in the subsurface. Magnetometer surveys can also define some metamorphic units efficiently. Then, drilling must ensue to confirm lithology and determine extent of mineralization.

Jan 1, 1992

By Brett Schug, Caelen Anderson, Sohail Nazari, Carlos Cristoffanini

"The Haile gold mine in South Carolina is increasing the automation level of its processing plant in order to improve operational stability. One step toward this goal is the application of a digital twin concept to provide virtual instruments. Haile has engaged Andritz to implement virtual instruments at its grinding area hydrocyclones and at its tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The digital twin is a first-principles integrated design engineering with advanced simulation (IDEAS) simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters.OceanaGold’s Haile gold mine is located near Kershaw, SC, about 80 km (50 miles) southeast of Charlotte, NC. This location was first mined in 1827 and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile operation.The current operation began in 2017 as an openpit mine with additional underground resources. The nameplate throughput is 5,760 t/d (6,350 stpd) ore, and 2017 production was 3,345 kg (118,000 oz) gold, with 3,968 to 4,384 kg (140,000 to 155,000 oz) gold expected in 2018. Proven and probable reserves exceed 85 t (3 million oz) gold at a grade of 2 g/t (0.06 oz/st) gold. The process, as shown in Fig. 1, includes a primary jaw crusher, comminution with a semiautogonous grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon-inleach leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile operation’s inaugural gold pour took place Jan. 20, 2017. Mine life is expected through the year 2030."

Dec 1, 2018

By H. N. Frock

The use of low-angle forward light scattering for measurement of particle size distribution has been described previously.1 Laboratory instrumentation using this technology is used routinely in operating plants for quality control and production control.2,3 Extension of the technique to on-line process monitoring and control has also been undertaken in several important areas. This paper will discuss the application of MICROTRAC R systems to the monitoring of particle size in wet slurry processes and dry powder grinding circuits. Examples of existing installations will be given with emphasis on performance and on-line reliability.

Jan 1, 1979

By M. C. Williams

As the flaws in the population balance model (PBM) comminution model are examined more deeply, further errors and problems were discovered. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalization assumption. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions.

Jan 1, 1993

By J. García, B. Arango, F. Calderón, O. J. Restrepo-Baena, A. Carreno, L. Rojas-Mendoza, J. Pérez, E. Bedoya

"Tungsten extraction is a subject of global interest due to is properties. These properties, such as its high melting point, have contributed to the development of metallurgical extraction processes that can be adapted to the particular chemical composition and mineralogy of the ore. In Colombia there is a research deficit in tungsten related areas, and especially with regard to its extractive metallurgy. In this study the physical, chemical and mineralogical characterization of a sample were performed. Subsequently, crushing and grinding were employed to reduce the material to a more convenient size, making it suitable for further concentration and metallurgical processes. Through physical concentration techniques it was obtained a concentrated ranging between 60 -70 % of WO3 content.INTRODUCTION Tungsten is a metal of great economic importance due to its excellent properties such as high density and extraordinary melting point 3422°C), which is indeed the highest of all the elements. Tungsten is primarily used in metal alloys, manufacture of special steels, coatings and catalysts; products of interest to both international and national industry. However; given that the use and economic value is determined by the percentage of tungsten in the mineral, particle size and chemical associations, it becomes essential to properly characterize the mineral to further define possible metallurgical extraction routes. The metallurgical processes for minerals enriched in tungsten may vary depending on location and the genesis of the ore body, which means that for each ore a particular set of operating conditions must be determined. This is important since process standardization can lead to misuse of the mineral resource. However, in Colombia there is a research deficit as it relates to minerals enriched in tungsten and to its extractive metallurgy. Then, there is a need to conduct studies that can lead to a better understanding of the ore, and to develop extraction processes for the metal of interest. EXPERIMENTAL A state of the art review was made in order to gain insights of the tungsten metallurgical process. Comminution was necessary with the aim to reduce the sample size; therefore the sample was taken into crushing and grinding stages. Concentration techniques such as magnetic separation, gravity and / or electrostatic were also applied. Physical, chemical and mineralogical characterization were performed by using polished sections, grain size determination, X-Ray Fluorescence (XRF) and X-ray diffraction (XRD) techniques."

Jan 1, 2015

By Ulrich Maidl, Jamal Rostami, Ulf Gwildis

Tunnel Boring Machines (TBM) have more or less become the preferred method of tunneling in various ground conditions and Programmable Logic Controllers (PLC) or microprocessors are standard features on TBMs to monitor and record various sensory systems on the machine providing the possibility for machine automation and control. The data collected from these sensory systems and channeled through PLC is stored for real-time analysis or use by the operators. Based on typical construction specifications, part of the information collected in the process is shared with the project management team representing the owner. Machine data automatically acquired during TBM advance is typically processed by specialized software to offer the project team data visualization and evaluation options. Interfacing with Geographic Information System (GIS), Computer-Aided Design (CAD), 3-D geologic model, instrumentation data bases, and Document Management Systems (DMS) allows for developing Building Information Models (BIM) of the tunnel’s as-built condition. Application of Artificial Intelligence (AI) processes such as Machine Learning (ML) have already been used for analysis of data, including performance prediction of hard rock TBMs, and exhibited the potential of big data analytics in improving the productivity of the operations. This paper outlines anticipated disruptive technological advances with implications on geotechnical exploration, TBM operation, face condition tracking, subsurface risk allocation, and claims management in the future.

Jun 13, 2021

By William A. Wallace

Common mineral resources (sand, gravel, crushed stone, etc.), which are so necessary for the construction of metropolitan areas, are rapidly being depleted or otherwise rendered unavailable in the very areas that need them most. However, the problem of planning for these resources involves a number of independent and dependent variables that must first be defined and related. Finally, a dollar value must be assigned where possible. Complex interrelationships between the variables and their dependence on outside factors has made mathematical "solution" of the problem of planning for non-renewable mineral resources difficult at the present time. Therefore, the use of computer simulation is suggested as a means by which this complex problem can be investigated. The purpose of this paper is to report on a continuing research program whose objectives are: (1) to delineate the factors involved in planning for the utilization of common mineral resources in urban-suburban environs; (2) to construct a planning model for these materials amenable to computer analysis, (3) evaluate the model by using test cases, and (4) perform a sensitivity analysis to determine the initial parameters in future planning for these materials.

Jan 1, 1968

By D. U. Gustafsson

After half a million meters drilled with Wassara we are now confident that ITH hammers powered with simple water will become an established product for production drilling. Today four drill rigs in LKAB Malmberget equipped with Wassara drill about 25 000 m per month of 4 1/2" holes. In Kidd Creek, Canada, Was sara is used for production drilling in stopes with good results. The first Wassara 6" hammer has drilled a 36 meter long, completely straight horizontal cut hole for drifting in the LKAB Malmberget Mine. Main advantages are about doubled penetration rate, very good air quality and improved hole cleaning which facilitates stabilized drilling. Disadvantages are resistance to new technology and, in some cases, the increased use of water.

Jan 1, 1995

Longwall mining is a commonly used method of coal extraction that involves the complete removal of large, rectangular panels of coal. Longwall mining causes the immediate seam roof to break and fall into the void created by mining. The convergence of the surrounding strata towards the mining void causes subsidence on the surface. The subsidence magnitude is related not only to the mining depth, the topography, the geological features and the overburden materials, but also to the sequence of the strata overlying a coal seam. In additional to the vertical subsidence which is evident at the surface, there are also horizontal movements inwards toward the centre of the void, which cause the surface to tilt, bend, stretch and com-press. This paper presents a parametric investigation of the influence of the overburden stratigraphy to surface deformations due to longwall mining using 2D finite element models. Models simulate rock movement by applying equivalent edge load to the open roof.

Jan 1, 2008

By Malcolm J. Robinson

Over 80% of Australia's population lives within 200 km of the coast, 70% in 10 major coastal cities. Potential cement raw materials are widely distributed but deposit size, quality, transport, market and environmental considerations are important in determining economic value. Major production locations are in a variety of geological environments ranging from Lower Paleozoic crystalline limestones to Tertiary and Recent polyzoal limestones and limesands, both onshore and offshore. Raw material transportation is by road, rail, sea, aerial ropeway and pipeline; road/rail transportation of the finished product is traditional but movement by sea of clinker and cement is increasingly a feature of the industry.

Jan 1, 1982

Gold cyanide equilibrium adsorption isotherms in the loading range typical of operating carbon-in-pulp/carbon-in-leach plants have been established and the effect of various cations and the presence of copper cyanide species quantified. It was found that the equilibrium loading of gold was enhanced by the presence of sodium or calcium, with calcium having an order of magnitude stronger effect. The presence of copper has an adverse effect on the equilibrium loading of gold. A unified model was developed to predict the effect of sodium and calcium concentrations in solution and the competitive carbon adsorption of copper on the equilibrium loading of gold on carbon. A satisfactory agreement between the measured gold equilibrium loadings and the model results was obtained over a wide range of solution conditions.

Jan 1, 2010

By M. S. Moats, A. Luyima, W. Cui

"Organic smoothing additives are used to produce dense, thick, high-quality cathodes in copper electrowinning. Glue had been used traditionally and is still used in operations that do not employ solvent extraction to produce the electrowinning electrolyte. With the advent of solvent extraction–electrowinning, guar started to be used and remained in use for many years as it does not affect the phase disengagement in solvent extraction. Recently, however, guar has been replaced by less-expensive saccharide- and polyacrylamide-based additives. This paper is the first of a series of four papers that examine saccharides and polyacrylamides as new additives for copper electrowinning. A review of previous research related to copper electrowinning additives is presented here, along with a selected review of additives in other copper electrodeposition systems.IntroductionThe recovery of copper from solution by electrowinning was first practiced in the early 1900s, but it was the combination of solvent extraction with electrowinning (SX-EW) in March 1968 at the Ranchers Bluebird Mine (Kordosky, 1992) that changed the landscape for the electrowinning process. Most copper electrowinning capacity is now associated with solvent extraction, though some copper is still won directly from leach solutions (Robinson et al., 2013). The ability to produce high-purity copper cathodes from SX-EW has taken the continued improvement of SX-EW technology over the past more than 40 years.One of the technologies that has seen improvement is that of the organic smoothing agents used during the electrodeposition of copper in the tankhouse. These organic additives are added to the acidic copper sulfate electrolyte during electrowinning to improve the smoothness, brightness and density of the copper cathodes. The organic additives that are presently in use are different from those used in 1999 (Jenkins et al., 1999). Over the past decade, many tankhouses have replaced the use of guar-based organic additives with those derived from other saccharides. Until now, there has been no comprehensive publication in the open literature on the behavior of these additives during copper electrowinning."

Jan 1, 2016

By Panshi Xie, Yan Chen, Shaogang Wu, Yang Hang

In order to realize the intelligent mining of coal seam with large dip Angle, this paper adopts the methods of large proportion variable Angle loading threedimensional physical simulation experiment, numerical simulation and field measurement with digital twin technology. The hydraulic support with large dip Angle and large mining height is used as the prototype to design the physical entity model of 1:5 hydraulic support, combined with modeling and graphics rendering technology. Angle, displacement and load sensors were selected and placed to realize the data channel between the lower machine and the upper computer of the digital twin system, so that the position and load data of the physical entity model and the twin model of the laboratory hydraulic support could be shared in real time. Moreover, the multi-dimensional dynamic and static load transfer law and the position evolution characteristics of the support and surrounding rock under different inclination angles were analyzed. The results show that: with the increase of the Angle of the working face, first, the initial support force required by the support decreases, and the damage degree of the roof increases; When the roof is soft, the lifting operation can avoid the instability of the support to a certain extent. Second, under the action of positive pressure, the load of the top beam under different angles is balanced; Under the backpushing action, the load in the upper inclined area of the shield beam increases gradually, while the load in the lower inclined area decreases gradually. Under the lateral push, the load changes periodically, and the load in each cycle is increased compared with that in the previous cycle. Third, the numerical simulation analysis shows that the load on the lower bracket is less than that on the upper bracket, and the load on the bottom of all the columns is greater than that on the middle and upper brackets. In order to reduce the impact of the columns on the bottom plate or the base, it is necessary to improve the anti-subsidence ability of the base. Finally, according to the research results, the improvement and optimization measures of the support are put forward, and the field test shows that these measures effectively solve the problems of sinking, sliding and tipping of the support in the working face with large inclination Angle, and obtain good application results.

Feb 1, 2024