Search Documents

By F. Gonzalez, A. Zambrano, J. Schwoebel, S. Kravits

Significant lost time delays were experienced by Carbonifera de Nueva Rosita, S.A. de C.V. ("CNR") during mining development of the Pasta de Conchos Mine ("the Mine") near Nueva Rosita, Coahuila, Mexico. Furthermore, methane gas concentration in the return air course had exceeded 1.0 percent. Resource Enterprises, Inc. ("REI") was contracted by CNR to recommend an approach to reduce methane emissions at the Mine. In order to recommend a degasification approach, REI and CNR obtained geologic and reservoir characteristics of the Double coal seam, Olmos Formation. A vertical core hole was drilled to obtain core samples to determine gas content (average 8.4 cm3/gm) and to conduct a slug test to estimate permeability (34 md). This information was used to simulate gas productivity and drainage effectiveness. The simulation indicated that underground horizontal boreholes would remove significant quantities of gas in advance of mining in a reasonable period of time. Based on the results of the simulation study, an underground degasification drilling program was initiated at the Mine. In a six month period, five long in-mine degasification boreholes were drilled in advance of CNR's three to five years mining projections. Peak gas production from the five boreholes (approximately 2,750 cumulative meters) had exceeded 45,000 m3/D. Results to date have indicated a general reduction in methane concentration in the return air course below 0.8 percent.

Jan 1, 1993

By James J. Fallon

I'm glad this meeting is being held in New York. First, because the city is close to my home in New Jersey, only 35 minutes from Times Square ..... if I were to come to Times Square between two and three in the morning. Otherwise it takes two hours. But even more important is the fact that all of you good people from around the country and around the world will enjoy the unique experience of that warm friendly atmosphere in the greater metropolitan area, something that you won't see any place else on the face of the earth. Seriously, the greater metropolitan area has been a large part of my industrial, cultural and spiritual experience. There are many aspects of it which I find disagreeable but on net I would rather live in this area, at least for the time being, than any other area of the United States. As a consultant I find contact with financial institutions, corporate headquarters, information sources and a great many production and research facilities a valuable asset to my activity.

Jan 1, 1985

By J. D. Vincent

The Mission By-Products Plant at the Mission Concentrator of the American Smelting and Refining Company, some 20 miles south of Tucson, Arizona in the Twin Buttes mining area, has been in operation slightly over a year. The plant produces a molybdenite concentrate a copper concentrate and, at times, a zinc concentrate. An intensive test program of over three years was conducted at Mission to make the recovery of molybdenum economic. Briefly it was found necessary to make a scavenger concentrate in the copper mill before it was possible to recover economic quantities of molybdenite. By so doing there were resulting additional recoveries of copper, silver and zinc. This program resulted in the design and construction of the existing plant. A paper by the authors discussing the test work and the design was presented at the, October 1965 meeting of the American Mining Congress in Las Vegas, Nevada, by Mr. Wayne Bossard.

Jan 1, 1966

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By John H. Archibald, Arthur L. Miller, George A. Savanick

As part of its continuing research on selective mining, the Bureau of Mines has made progress toward developing a tool capable of remotely extracting hard minerals through a borehole. As the successor to the successful borehole miner, which extracted soft materials through a straight borehole, this new device has several innovative features: 1) it can propel itself in and out of an 8-inch borehole; 2) it can cut hard rock with an abrasive jet and transport the cuttings to the surface; and 3) it can negotiate deviated boreholes--the feature that enables it to follow a vein and extract only the values. This paper describes the development and feature testing of the reamer/miner.

Jan 1, 1991

By G. Hoffmeyer, I. Ream

"Several copper projects exclusively utilizing in-situ recovery methods are currently under development in Arizona. Favorable conditions for In-Situ Copper Recovery (ISCR) include a saturated orebody, fracture hosted mineralization, hydraulic conductivity sufficient to effectively inject and recover solutions using wells, and a relatively flat background hydraulic gradient. Safe operation of an ISCR project requires that the operator have the ability to induce and maintain localized hydraulic gradients, thereby controlling the movement of injected and recovered solutions. Benefits of ISCR include reduced initial capital, and a greatly reduced environmental footprint. THE ISCR METHOD EXPLAINED The method chosen to extract a mineral from a deposit is driven by characteristics such as its size, grade and depth of burial. Large lower grade deposits that require significant excavation to access using surface methods are potential candidates for in-situ recovery. ISCR may also be ideal for smaller deposits due to the lower initial capital. However, regardless of the size of the deposit, certain hydrogeologic conditions must be present for ISCR to be successful. In-situ recovery methods do not require excavations of rock from the surface or underground, resulting in a dramatic reduction in surface disturbance when compared to conventional mining. With the ISCR method, what is visible above ground is the processing plant, well heads, piping, process solution impoundments and evaporation ponds. There are no waste rock piles, tailings impoundments, leach pads, or impacts associated with blasting and hauling. Other benefits include reduced initial capital, reduced dust and noise, and lower water use. Early testing of the in-situ copper recovery method by Occidental on the Van Dyke deposit east of Phoenix and by Kennecott at Safford Arizona in the 1970s produced encouraging results, but the permitting regime for a large-scale operation was not yet in place. Additional testing and commercial application of in-situ copper recovery techniques have expanded since the 1980s, most commonly in conjunction with open pit or underground mining operations. For example, several operations in Arizona (San Manuel, Miami East and Tohono) have used in-situ techniques to extract additional copper following conventional mining from parts of the deposits adjacent to open pits or underground workings. Where the rock has been broken up by conventional methods, the method is called “in-place” leaching. The US government has also been involved in assessing in-situ techniques. For example, joint research was conducted by the US Bureau of Mines and industry on the Santa Cruz deposit in Arizona; and both federal and state agencies have been involved to establish the comprehensive permitting regime that exists today. Currently there are several projects in Arizona being evaluated as stand-alone ISCR operations."

Jan 1, 2016

By Stanley W. Ivosevic

Introduction Increasing investor and industrial demand for gold is not being matched by new mine output from traditional sources. This forces the exploitation of alternative natural and industrial resources to supplement traditional sources. A traditional natural resource is either high- to medium-grade ore, of gold or silver with coproduct gold. Or, they are medium- to low-grade base metal ores having byproduct gold. Traditional ores are also frequently extracted at relatively great expense by selective underground mining. Alternative natural resources include low-grade, near surface ores and the products of mining-dumps - and of onsite processing - tailings. Traditional industrial resources are newly mined gold or that obtained from plant sweepings. Their alternative analogues include gold in old scrap and chemical sludges and precipitates, notably those incidental to the electronic industry. These alternative gold resources have several attractions. They are untapped and abundantly available. Having been overlooked by prior metals suppliers, title to many alternative resources is easily acquired. Or, the value of such a resource may go unnoticed until its gold is rendered exploitable by an advance in extractive technology or an other approach. This article addresses the effect of large tonnage, low-grade lode ores on gold supply. Exploiting these ores is rendered commercial by their amenability to bulk mining by modern large-scale mining and metallurgical operations requiring little selectivity. Placer gravels, perhaps the earliest type of gold ore mined, also are bulk minable. But these fall outside the definition of being lode deposits. Most lode bulk mining is from surface open-pit mines. Some, however, is from underground by such large-scale mining techniques as room and pillar, vertical crater retreat, and end slicing. The low-grade gold ore being discussed averages 2.8 g/t (0.082 oz per st). Output How greatly do bulk minable, low-grade resources effect supply? 1982 was a somewhat healthy year for gold mining and exploration in North America in spite of the general depression in the mining industry (Table 1). The wildly fluctuating price of gold bullion had stabilized at an annual aver¬age of $12.08/g ($376 per oz) - (Handy and Harmon base price). Half of the 1.3 kt (43 million oz) of 1982 world gold mined were from South Africa's high-cost, medium-grade, selective underground mines. Of the remaining half, 20%, or about 130 t (4.2 million oz), was mined in North America. This includes Canada and the US - the third and fifth largest gold producers in the world. Of that North American production, more than 62.2 t (2 million oz) of gold, or about 50%, came from bulk mining of gold ores with or without co-product silver. Most of this was in the US, where bulk minable gold-silver lode ore produced nearly 31 t (1 million oz). This amounted to 60% of the nearly 46.6 t (1.5 million oz) produced in the US during 1982. An additional nearly 7.7 t (250,000 oz) of gold were produced as the byproduct of bulk mining of cop¬per ore, for a total of 34 t (1.1 million oz) of gold, or 75% of US gold production by bulk mining. To further illustrate this, US placer, mine dump, and related operations produced an insignificant 4% of US gold output at the time. Exploitation of bulk minable gold deposits is becoming increasingly important worldwide. Most new Australian gold mining announcements are of bulk minable developments. This trend will increase in North American mining as more large tonnage, low-grade operations come onstream in Canada, where much current production is from underground. It will increase with the general climb in Mexican gold mining. And it will grow with expansion of the 12 t/a (400,000 oz per year), gold production of the Dominican Republic. Production Metal price and operating costs make these large tonnage, low-

Jan 11, 1984

By M. J. Raffaldi, L. A. Sandbak, K. K. Dehn, S. N. Warren, J. B. Seymour

"Confidence in the design and stability of an undercut cemented rockfill (CRF) span requires a thorough understanding of its emplaced material properties. The unconfined compressive strength (UCS) of cast 6×12-inch QA/QC cylinders is typically used as an index test to track the performance of a backfill plant. However, these strengths need to be adjusted for oversize aggregate removal and sample size effects if used to estimate the emplaced UCS. UCS testing of 6×12, 12×24, and 18×36-inch cast CRF cylinders was used to quantify the relationship between readily available 6×12-inch QA/QC strength data and the emplaced UCS. Test results indicate that the UCS of 18×36-inch cylinders is roughly 40% of the 6×12-inch UCS for similarly compacted samples. Mine QA/QC data indicate that the UCS of CRF is highly dependent on the degree of compaction as measured by bulk density. Based on these results, knowledge of the emplaced CRF density compared to 6×12-inch QA/QC density is also necessary to estimate the emplaced UCS. The scale effect reported in this study is more pronounced, compared to current understanding of backfill properties discussed in the literature, and underscores the need for further site-specific testing. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SRMD), in cooperation with Barrick Gold Corporation, is conducting research with the goal of determining a relationship between 6-inch QA/QC cylinder strengths and the in-place strength of cemented rockfill (CRF). CRF cylinders with dimensions (diameter × length) of 6×12, 12×24, and 18×36 inches were cast onsite at the Turquoise Ridge Joint Venture (TRJV) and Cortez Hills Underground (CHUG) mines using CRF mixed at the mines’ respective batch plants. UCS tests were performed after 28 days of curing to estimate the size correction factor for each mine’s CRF. This paper presents an overview of the mix designs, sample collections, testing methods, test results, and an estimate of the UCS size correction factor for CRF at these mines. BACKGROUND Underhand cut and fill mining methods utilizing cemented backfill are common in underground metal mines in the United States. These methods are advantageous for controlling weak or highly stressed rock mass conditions by creating an engineered material that can be placed in openings, forming a beam that provides a safe, stable back for the next undercut. Increased use of underhand methods in the last 30 years has greatly improved safety in many cut-and-fill mines. However, with the continual push for more efficient and cost effective mining, there is a need to thoroughly understand the geotechnical properties of cemented backfill to assist in designing safe, stable openings while optimizing costs and production schedules."

Jan 1, 2018

By Khosrow Badiozamani

Traditionally the mining industry has been lagging in application of computers in their daily or long range plan activities compared to other industries. The question then remains as to how the technology of higher computing capacity for less cost is going to affect the mining industry and how the lukewarm reception of engineers in acceptance of computerized mine planning in the past is going to change because of the new wave of high techology. These questions and the reasons for the lack of usage of computerized mine planning systems by engineers will be evaluated in this paper. In addition, alternatives available to the mining industry will be analyzed and the direction of the future "user friendly" software will be discussed.

Jan 1, 1984

By Gary E. Slagel

The federal Office of Surface Mining (OSW) has undertaken an effort to revise many of their permanent program regulations. Numerous procedures for compliance are being rewritten to allow for greater flexibility while meeting the requirements of the Surface Mining Control and Reclamation Act. This study investigates, for certain select provisions, the cost differential between complying with the original OSM standards and the more flexible, state-specific standards being allowed in many of the revised regulations. Estimated cost savings that could be realized under a few of the revised regulations are substantial and should provide a basis for seeking revisions to the state regulatory programs.

Jan 1, 1982

By William S. Gilmer

INTRODUCTION As man moved through the ages into the era of metals, he became increas¬ingly dependent on the extraction and beneficiation of various ore types. His progression has required more material, new sources, and inevitably, a need to extract the values from ores of much lower yield. Inherently welded to this need to extract has been the attendant requisite of power and water to carry out these tasks. With the richness of these deposits diminished, and the in¬crease of demand, mining has become so intimately tied with the needs of these auxiliary systems that the modern day milling operation can ill afford to ignore them. In the times of Agricola 16th century methods of milling required little thought for power or water consumption. Reduction was accomplished by hand¬sorting and hammer and grinding done with stamps and millstones. Medieval concentration was carried out by the "Jigging sieve" with agitation supplied by the sleeveless arm of the operator (The Mines Magazine,_ March 1933). Little consideration was likely given to the power source unless it became apparent that he had insufficient means to meet the demands of a dawn to dusk operation. Fuel for power production was also probably of little consequence unless sustained drought or warring neighbors burned the miners fields. Water was available from any adjacent stream with recycle, potable, tailings and mill consumption all going and coming from the same source. By the end of the 18th century and the early 19th century the requirements of larger throughputs and better re¬covery were forcing the miner to the need for greater sources of power and water. Arrastras, capable of accepting several hundred pounds of charge, con¬sisted of a clay bottom, a "liner of rocks harder than the substance to be crushed" and a revolving center post in which the ore was ground and amalga¬mated. Used in conjunction with a slucing system, this formed the primary recovery method of the time. Power was supplied by horse or oxen or, if terrain was amenable, by use of a horizontal or overshot water wheel. A typical system required 4.5 kw (6 hp) and needed to run in the vicinity of 15 rpm (Pre¬ston, 1895).

Jan 1, 1986

By David Pentz, Paul Hodges

GENERAL INTRODUCTION The object of this paper is to discuss those aspects of open pit mine design which are affected by geotechnical factors. The temptation exists for some practitioners of geotechnical engineering to believe that this relatively new engineering discipline is the ‘be all and end all of mining.’ In the opinion of the authors, this is fallacious but, as our ability to put numbers to the behaviour of rocks and soils improves, it is clear that geotechnical engineering will become an integral and important part of designing and operationg mines success- fully. Open pit mines in the context of this paper also includes open cast mines, where the 'ore" is extracted and the waste material is immediately replaced or ' backfilled in the mined portion of the pit. Open pit mines operating today move from very small tonnages a day to in excess of 400,000 tons per day. Several mines are operating and are being designed to capital expenditure for such projects in some cases exceeds five hundred million dollars and in a few cases will exceed one billion dollars. The size of this investment means that financing will have to be provided from banks or joint partnerships. This financial environment means that planning will be carefully scrutinized by experienced representatives of financial institutions or other mining companies. All too often a project has been put in jeopardy because the personal desire of one or two men to make a project proceed has caused incomplete planning or perhaps in some instances deliberately leading observers 'down the garden path.’ In our opinion the day is rapidly arriving when the quality, logic, practicability and completeness of the planning will make the difference between securing financing or not and, in the cases of existing open pit mines, of the difference between survival and closure.

Jan 1, 1977

By Richard D. Nichols

A new method of slaking lime has been developed by DENVER EQUIPMENT DIVISION of Joy Industrial Equipment Company and patented under U. S. Patent 4,261,953. The new method utilizes an attrition machine, commonly used in mineral processing circuits as a sand scrubbing device, to slake lime. The scrubbing effect of the attrition slaker continuously produces a fresh reactive surface so that further slaking may occur. This process allows for utilization of slaking all grades of burnt lime and most grades of dolomite lime. Testing indicates that poor grades of water usually not considered for this service can now be tolerated using the attrition slaker. The slaked lime produced is of higher quality, faster reacting and much less apt to produce scaling problems than previously experienced. The attrition slaker can be combined with a spiral classifier and ball mill to eliminate any need for grit handling or grit removal. The attrition slaker can be designed for all burnt lime tonnages up to the limit of 175 tph and 1" pebble lime size. Control can be maintained easily with minimal operator assistance. The equipment, the principals of process metallurgy, and the above topics will be presented.

Jan 1, 1982

By William Gleason

"Modern society demands much more from the mining industry than just the raw materials it produces. In addition to providing copper, gold, coal and other minerals that make society function, the industry must conduct its operations in a safe and environmentally sustainable manner. This includes the equipment used and the engines that power the machines.In the United States, Tier 4 diesel engine standards that were set by the U.S. Environmental Protection Agency (EPA) are the strictest emissions requirement for off-highway diesel engines. This requirement regulates the amount of particulate matter (PM) and nitrogen oxides (NOx) that can be emitted from an off-highway diesel engine. In Europe, the Euro V standards are driving technology advancement in the sector.The European Euro V standards are required for new equipment manufactured beginning in January 2019. U.S. Tier 4 standards for heavy-duty off-road engines came into effect with model-year 2014 vehicles and equipment. China 6 standards come into effect in July 2020. India’s Bharat Stage VI standards will take full effect in 2020, and the phase-in of BSVIcompliant clean fuels began in April 2018.Caterpillar, Cummins and MTU are three of the leading manufacturers of engines for the mining sector. Each company is working toward creating efficient engines that can function in the often harsh environments found at openpit and underground mines around the world. In short, society is placing demands that are challenging engine manufacturers to deliver a product that can do more work while consuming less fuel and emitting fewer emissions.Technologies range from selective catalytic reduction (SCR) and diesel particulate filters (DPFs) to other engine strategies and emissions control technologies, which deliver near-zero black carbon and nitrogen oxide emissions, and lower greenhouse gas emissions. Caterpillar’s investmentCaterpillar, the world’s largest producer of mining equipment and mining engines, has been at the forefront of the changing demands placed on the industry and has remained on the cutting edge of engine development over the years, thanks to its investments in the sector.“Caterpillar made the choice to fund major engine and machine development work — even during a deep trough in the mining industry — so that Cat machines would meet Tier 4/EU Stage 5 mandated compliance dates of Jan. 1, 2018 / Jan. 1, 2019, respectively. For Caterpillar, these efforts enabled our mining trucks to provide improved engine component life to help our customers’ total cost of ownership (TCO) and produce a neutral TCO compared to our Tier 2 products,” said Jeff Castleman, new product introduction manager, large mining trucks for Caterpillar."

Aug 1, 2019

By R. Robertson

Dense medium cyclones are the preferred means for cleaning 112 in. x 14 Mesh to 28 Mesh (12.7 mm x 1.0 mm to 0.6 mm) raw coal and are becoming a common choice for cleaning raw coal from a nominal top size of 2-1/2 in. to 3 in. (63.5 mm to 76.2 mm) down to 14 Mesh to 28 Mesh (1.0 mm to 0.6 mm). During the last ten years, dense medium cyclone circuitry design has undergone changes which have combined to improve process efficiency. This paper describes these improvements and compares present day design with the design used prior to the mid 1980's. Improvements in the following areas are described: Raw coal desliming, cyclone configuration, drain and rinse applications, dilute medium circuitry, and instrumentation and control.

Jan 1, 1997

By M. C. Fuerstenau, J. J. Fitzgerald

Aluminum silicate hydrosol synthesis and characterization are discussed. Plausible polymeric aluminosilicate species are presented together with their effect on electrokinetics of selected minerals and flotation response of various ores. The addition of aluminosilicate hydrosol to porphyry and oxide copper ores and to a tungsten ore resulted in enhanced flotation recoveries ranging from about 1.5 to 5 percent. A significant portion of the nation's mineral resources are presently lost in the form of particles with very fine grain size. In the case of copper, for example, approximately 225 million tons of ore are concentrated by flotation per year in the United States. Total losses from porphyry ores are generally 15 to 20 percent with half of these losses being finely-divided copper sulfide minerals which do not respond to flotation. The additional 5 to 10 percent loss is the result of copper oxide minerals which are not floated. The losses of copper sulfide minerals are thought to be due in part to the lack of appropriate dispersion of the finely-divided solids less than 20 microns in size. To effect dispersion in flotation systems, sodium silicate is commonly added. Enhanced dispersion effectiveness is achieved when polyvalent metal salts are combined with sodium silicate. Since originally described by Patek (1), numerous workers have explored the utility of metal silicates. Makrousov (2), Belash et al. (3), and Eigeles (1950) (4) showed the applicability of these reagents to calcite/apatite and fluorite/calcite ores. Mercade (5, 6) reported depression of calcite in the presence of 3.33/1 mole ratio Al/Si hydrosols prepared from Type N sodium silicate (Si02/Na20 ratio 3.22/1) and 1% A12(SO4) 3•18H20 solutions. He importantly observed that the colloidal precipitates did not play a significant role in dispersion and depression but that the soluble species were responsible for this action. Patented work by this author described metal silicates used to depress calcite in scheelite flotation using 1% metal salt (FeSO4•7H2O, CoSO4•7H2O, etc.) and 5% Type N sodium silicate solutions to produce hydrosols with Si/Fe or Si/Co ratios of 8.79/1. Aluminum (III) ion systems were less effective as depressants than the iron and cobalt systems. Yang (8, 9) has studied metal silicate sols for use in the flotation of lithium and ultra-fine hematite ores. Using 10/1 Si/Fe mole ratio hydrosols prepared from 2% ferric nitrate, Fe(NO3)3.9H20, and 5% Type N sodium silicate solutions, solutions, he showed that the hydrosols either modify the slime particle surfaces or are adsorbed on the slime particles preventing anionic collector adsorption. In a subsequent patent, Yang also reported the use of these hydrosols as dispersants for beneficiation of lithium ores. Recent studies of aluminum silicate hydrosols in the flotation of chalcocite, chalcopyrite and scheelite have been reported using Si/Al dispersants prepared from 5% Type N sodium silicate and 0.1 M aluminum chloride (A1C13.6H20) solutions. Dispersant properties were shown to be dependent upon the method of synthesis, supernatant pH, and the hydrosol Si/Al mole ratio. Polymeric soluble species in these hydrosolsupernatants have been proposed as the active dispersant species. Aluminosilicate hydrosols are synthesized by the general reaction scheme presented in Figure 1. Commercial sodium silicates are available with ratios of SiO2 to Na20 of 1.60-3.25. The sample which is most frequently employed is Type N whose ratio of Si02/Na20 is 3.22/1.00. Gel filtration chromatography and NMR studies have shown that these sodium silicates contain numerous species of molecular weight from 325-2,000 gm/mole. Monomeric, oligomeric and higher molecular weight linear polymeric arrangements of these structures are found in these solutions.

Jan 1, 1989

By R. L. Derick

The Orchard Valley Mine, a large underground coal mine located in western Colorado, experienced a major mine fire during an idled Sunday on June 1, 1986. This mine had extensive problems with spontaneous combustion near the coal outcrop. Spontaneous combustion has been determined to be the probable cause of that fire. Preparing for a mine emergency was an on-going task. Once the emergency occurred, much of the preparation work was implemented and aided in controlling the situation. Later, the successes and shortfalls that arose from that emergency were analyzed for future course of action. This paper summarizes the activity that led up to the major fire, the handling of that emergency, the lessons learned, and the changes implemented.

Jan 1, 1993

By Christopher J. Bise

The potential of the coal reserves in the western United States for meeting future energy needs has been recognized for quite some time. However, two of the major constraints which have tended to limit the development of these reserves which can only be deep-mined are the great thicknesses of the coal seams encountered and their high pitch. Although new mining methods may need to be developed to recover these reserves, at least in the short- term the industry has to incorporate presently available equipment which were not originally designed for thick-seam mining. The purpose of this paper is to present an analysis of the various equipment that are in use today and their possible application to thick-seam mining. The paper also addresses the various ground control and safety considerations that are unique to thick-seam extraction.

Jan 1, 1981

By Richard D. Zigmond

In this paper, a computer program that has been developed for determining the capital and operating costs for coal preparation plants is described along with its applications. The logic of the computer program is based upon the results of a survey of existing preparation plants, operators, plant contractors, equipment manufacturers, and consulting firms. This survey provided information on plant performance, order-of-magnitude costs, and costing procedures. Additionally, an extensive cost data file for the major capital equipment in coal preparation plants has been developed. Using the washability data and the computer program outputs, the cleaning costs per million Btu can be calculated. Details about the program and its applications can be found in a report by the authors (Zigmond et al., 1979).

Jan 1, 1981

By Shosei Serata

In the past, salt cavities for storage of liquid and gaseous fuels have been developed and operated using practical experience as a guide rather than rock mechanics principles and practices. Although many salt cavities are still operating satisfactorily. some of them are beginning to show various problems associated with long-term deterioration of the cavities. This paper describes a major breakthrough in the rock mechanics design of solution cavities which is the development and application of the REM computer simulation system. From the computer simulation analysis, the long-term deterioration process of cavities can be related to the basic parameters of rock mechanics design and the storage operations. The computer simulation system is also used for optimizing cavity design and operational specifications. This optimization technique is explained by its application to the three basic storage systems: 1) open dry storage system for liquids and solids 2) open wet storage system for liquids 3) pressurized storage system for gases, liquids and solids The effectiveness of the optimization technique is illustrated with some field examples by showing the direct interaction between the computer simulation system and field data of a test well including tectonic stress conditions, material property coefficients and geological anomalies.

Jan 1, 1974