Search Documents

By R. D. Hansen

This paper discusses the influence of frother type and dosage on recovery/selectivity in coal/sulfide mineral flotation as a function of particle size. It is shown that different frother structures do exhibit quite different but consistent performance characteristics depending on the underlying particle size ranges involved as well as the dosage levels of both the frother and collector. The data presented on existing commercial frothers end some new special purpose experimental frothers is used to illustrate some general operator guidelines on proper frother selection and use.

Jan 1, 1985

By Thomas F. Clemens

This paper covers various changes in government regulations, taxation, and legislation for the past two plus years and the up- coming one. Part of the paper will discuss recent business conditions and how they have affected the cement and lime industry.

Jan 1, 1983

By Gary L. Simmons

Over the past several years, Newmont Gold Company (previously Santa Fe Pacific Gold Corporation) developed a new technology for the flotation of refractory auriferous sulfide minerals which is referred to as the N2TEC flotation process. Starting in April 1997, the first commercial flotation plant utilizing N2TEC technology was successfully commissioned at the Lone Tree Mine near Valmy, Nevada. The Lone Tree flotation plant was designed to process 4,085 mt/d of ore producing 494 mt/d of sulfide concentrate. A flotation tails leach CIP circuit was added to recover cyanide-soluble gold from the flotation tails. A portion of the flotation concentrate is blended with whole ore feed to the Lone Tree autoclave, up to the limit imposed by the current oxygen plant capacity. The remainder of the concentrate is shipped to either the Twin Creeks autoclaves or the Carlin roaster for subsequent oxidation and gold extraction. This paper discusses the results achieved in the commercial flotation plant compared to pilot plant testing and engineering design flotation modeling. Capital and operating cost information are also presented.

Jan 1, 1999

By Miguel Carrera, Jose Arnal, Julian Ortiz, Maarten Haest, Fouad Faraj

ShovelSense is a complete solution for bulk ore sorting at the mine face that combines robust shovel bucket mounted X-ray fluorescence sensors, with real-time material classification, fleet management integration and supporting cloud-based data infrastructure, to ensure each truck always goes to the right destination. Correct truck destinations are a challenge in many current mining settings because the material classification of a truck, which is the key input into the truck destination, is often based on estimates at block resolution (~20x20x15m), with limited adjustment for blast movement and mixing. In this contribution, we present a geostatistical, data driven approach to estimate the potential value of bulk ore sorting at the mine-face for seven open pit mines. The approach is premised on the assumption that truck loads within blocks follow a simple gamma distribution. Standard ore control data from the seven mines have been used to estimate the potential bulk sorting value at these operations and ShovelSense-integrated dispatch datasets have been used to validate these estimates for specific benches on which ShovelSense operated. ShovelSense results validate the ore control data-based value predictions and show how at mine-face bulk ore sorting value varies between distinct deposit types. In general, deposit types that have higher bulk ore grade contrasts, display more potential ShovelSense value. The manuscript concludes with the limitations and opportunities of applying the proposed value estimation approach to evaluate at mine-face bulk ore sorting opportunities for open pit operations.

Jun 25, 2023

By J. F. T. Agapito

Two flat-lying trona seams 3-to 3.5-m thick, approximately 10 m apart, and at depths of 250 m are mined by room-and-pillar at OCI's Big Island Mine in Wyoming. Continuous miners and a yielding pillar system have contributed to improvements in resource recovery and productivity. Long-term stability with minimal subsidence is needed for a large portion of the mine beneath the Green River channel. This was investigated by computer modeling in 1990. Although results of the study indicated good long-term stability, recommendations were made for stress determinations to verify the model. Stress determinations made in 1997 showed pillar stresses 10% to 20% higher than the model stresses, and barrier pillar stresses 10% to 15% lower. This implies that higher panel stresses will be transmitted from the upper to the lower seam. A stability evaluation of the lower seam is planned before two-seam mining to assess entry widths and support requirements.

Jan 1, 1999

By Karin Bäppler

Lyon with half a million inhabitants is the third largest city in France. Urban agglomerations such as Greater Lyon demand intelligent underground solutions for the freedom of mobility of its inhabitants. The city and metropolitan area of Lyon provide an example of a city strategy adapted to the changing needs due to demographic and living standard trends. The Lyon Metro Line B with a length of 2.4 km is one of the strategic projects with regard to city planning and future mobility. The paper will highlight on this special area of application in singular diverse geology with sophisticated mechanized tunnelling technology.

Jun 13, 2021

By H. I. Meyer

The mine is a large open-pit copper mine located near Tucson, AZ. Mining operations involve shovels digging at relatively fixed locations and haul trucks moving the muck to a primary ore crusher, a primary waste crusher, and directly to waste dumps. The total investment in shovels and trucks is some $100 million. Fig. l is a schematic drawing of the operation. A static method of truck assignment is used; i.e., each driver is given one particular shovel to serve until reassigned by the dispatcher. A dynamic system is one where trucks are reassigned after each trip. The problem is to compute a near optimum assignment of trucks for efficient operation.

Jan 1, 1979

By H. Barry Holt, Charles A. Bischoff

On November 15, 1990, President Bush signed the Clean Air Act Amendments of 1990. The new legislation is sweeping in its demands for cuts in smog, acid deposition, toxic air pollutants and ozone-depleting chemicals. The Amendments will siqnificantly alter air quality permitting and compliance and are estimted to cost billions of dollars to implement. This article provides an overview and summary of each of the eleven titles of the Amendments. It also addresses how the Amendments will be implemented.

Jan 1, 1991

By Horst H. Gielen

Bong Mining Company/Liberia provides the rare opportunity to compare two generations of grate kiln pelletizing plants operating on the same magnetite/hematite ore basis. In this paper advantages and drawbacks are compared: mechanical aspects, energy-savings, pellet quality. Plant I with up- and down-draft drying gas flow. Plant II runs only on down draft drying and incorporates a heat-recoup system. Ferteco Mineracao/Brazil operates a Lurgi straight grate plant since 1977 on hematitic pelletfeed. Energy-political situation and char- coal as energy source in Brazil are reflected also in the search for alternative fuels for pelletizing. First measures and results are reported as well as intended further steps towards a 100 % oil replacement.

Jan 1, 1983

By M. Ghiani

Biohydrometallurgy originated, some forty years ago, from an environmental problem, namely the serious pollution of the Ohio river by acid drainage water coming from neighboring subbituminous coal mines. Studies aimed at elucidating the cause of the intensive oxidation of the iron sulfide (pyrite) inclusions of those coals, led to the discovery of a bacterium, Thiobacillus ferrooxidans (Temple and Colmer, 1951), capable of acting as a catalyzer, accelerating the otherwise very slow chemical oxidation of iron sulfide to rates many orders of magnitude higher. However, it is now recognized that the biotechnology of microbial mining dates back to 1963, when the ability of this bacterium to solubilize copper from sulfide ores was ascertained (Razzell and Trussell, 1963). Much research has been carried out on biohydrometallurgy over these last 25 years and is still being actively conducted all over the world. The interdisciplinary nature of this young branch of science and technology is reflected by the variety of experts involved: microbiologists, mining engineers, hydrometallurgists, physico-chemists, mineralogists, solid-state physicists and biochemists. This intensive research effort has provided a solid background on the fundamentals of this technology, although many important issues have still to be solved, amongst which the enzymatic mechanisms controlling biocatalysis of mineral sulfides dissolution, the influence of bulk- and surface solid-state physics of metal sulfides on dissolution mechanisms, the interaction of the various strains composing natural microbial floras. Their elucidation should permit the rationalization of biohydrometallurgical techniques and the optimization of commercial processes. Biohydrometallurgy has already achieved satisfactory results: copper recovery from submarginal copper sulfide run-of-mine ores (i.e. assaying less than 0.3% Cu) by in-situ, dump and/or heap leaching is successfully practised in many countries and uranium recovery through bioleaching is competitive with other leaching processes.

Jan 1, 1987

By T. O. Kuhl

The Royal-Mountain King Project is 7.2 kilometers (4.5 miles) northwest of Copperopolis, California. Reserves of 8,250,000 t (9,100,000 st) at 2.32 g/t (0.068 oz/st) gold will be processed at 2500 t/d (2750 st/d) from three pits. Production is scheduled to begin the first quarter of 1989. District geology consists of northwest trending sequences of Jurassic meta-sedimentary and meta-volcanic rocks. Three ore bodies are located along the Hodson fault which trends northwest and dips 40 degrees northeast. The Gold Knoll and North Pit ore bodies are hosted in carbonate and silica altered meta-volcanic rocks whereas the Skyrocket ore body is hosted in quartz stockwork zones in meta-sedimentary rocks. Gold is present as inclusions and micro-veinlets in pyrite.

Jan 1, 1989

By David Mast, Irwan Halim, Seung Han Kim

Fermilab is constructing a large underground cavern in Limestone to house scientific equipment. The cavern will have a complex L-shaped geometry and about 215-foot depth with relatively shallow rock cover, with service/egress shafts accesses into the cavern. Three-dimensional analytical models were developed to study the ground behavior and support performance. Multiple rock constitutive and failure models were evaluated. The models were significantly impacted by the high lateral in-situ earth pressure at the site. This paper will describe the design approaches that were taken to optimize the cavern arch geometry to allow safe construction in shallow rock, and permanent support requirements.

Jun 13, 2021

By J. L. Mehaffey

A variety of chemicals offered by Armak were evaluated as dewatering aids for aqueous slurries of silica sand, sparsand and feldspar; an established commercial dewatering aid was used as a control. A number of Armak's potential dewatering aids yielded lower moisture retention values than did the commercial product on all of the mineral samples. In addition to the chemical dewatering evaluations, some of the mechanisms involved in the removal of water from these mineral samples were examined.

Jan 1, 1983

By Rollin A. Slater

The bulk materials handling industry has served silently for years as the skeleton structure and often the central system of nerves and nourishment for the body of basic production industries. During the past two decades, this body has undergone substantial growth and mutation to meet the surging demands of our national economy for more and better products. The steel industry has been prominent in this phenomena and plants of the sixties are as unlike the second war vintage as our current crop of basketball players differ from their fathers. Steel has kept pace with spiralling demand by innovation which has resulted in new processes and improved designs which generally yield greater production from fewer units. The supporting industry of materials handling has likewise improved its techniques and currently has a new stronger generation of equipment to perform its necessary supporting function. It has been my fortunate experience to have been instrumental in the creative stages of several new steel mills which are currently in conceptual design or actual construction. Drawing upon exerpts from this experience, this paper will describe a basic approach to the selection and application of modern bulk materials handling systems to an entirely new steel plant. Specific details of past work are not available for publication, therefore, the plant described herein is a composite of ideas and will be the new plant of the Hypothetical Steel Corporation which will be located on the lower shores of the Great Lakes.

Jan 1, 1967

By D. R. Spears

The Bureau of Mines has investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed, and solids concentration on the kinetics of shear-flocculation. The results showed that shear-flocculation is a two-stage process. In the first stage, mean particle size increased rapidly in the first 1-2 min of reaction; in the second stage, an equilibrium was set up between the rate of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear-flocculation to occur and was dependent on solids concentration and collector dosage. This speed was the minimum necessary for particles to overcome the electrostatic energy barrier which kept conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1993

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By Manoj Kumar, Anil Kumar Singh, Prabal Patra, Ashish Agrawal, Souvik Ghosh, Subhashis Kundu, Kamma Ramakrishna Rao, Manish Kumar Gupta, Anindya Sarkar

The slag measurement systems in the cast house are very important. In the conventional method, the slag is granulated in a slag granulation system, and the slag flow rate is measured by the associated belt scale. However, in places where a slag granulation system is not available, the alternate approach is to deduce a theoretical calculation and develop the measurement because the commissioning of such slag granulation requires huge capital and has inherent geographical limitation. However, the theoretical approach suffers from several drifts and is far from the reality. In the present paper, we have innovatively engineered a sensor by designing the stellite-coated thermocouple that can measure the temperature of the slurry and placed it in such a way that the abrasive slag granules do not obstruct it, but we could measure the temperature of hot water, and further based on the thermodynamic approach, the slag flow rate is determined that can be compared with the theoretical approach. This approach of slag rate measurement is cost-effective and long-lasting.

Oct 2, 2023

By Keith G. Wallace, Gary K. Rogers

As a supplement to an analysis involving methodologies for the estimation of airflow resistance in shafts used for both ventilation and hoisting, a detailed shaft characterization survey was distributed worldwide. The survey provided detailed information which enabled verification of recommended velocities and established limitations on fill factors and relative velocities. This paper evaluates the information obtained for 37 shafts and presents a statistical evaluation of the results. Apart from airflow rates, conveyance rates, and physical characteristics, qualitative information regarding means of conveyance stability and velocity control techniques at unloading and loading points are also presented. Calculations of fill coefficient, free area velocity, and most importantly, relative velocity between the airflow and hoist, are conducted. These results are presented by frequency diagrams which illustrate the trends, as well as provide limitations for these parameters. The data illustrates that, commonly, the fill coefficient for two or more conveyances, does not exceed 30 %. A limit of 50% is suggested for a single conveyance shaft. A recommended free area velocity of 10 m/s (1,970 ft/min) for combined ventilation and hoisting shafts, is sup- ported by these results. Relative velocities of 30 m/s (5,905 ft/min) are most frequent and 50 m/s (9,840 ft/min) being a practical maximum.

Jan 1, 1987

By T. V. Ramey

Heap leaching in certain parts of the world, such as Chile's Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts in northern Chile the soils often contain very high concentrations of soluble salts (nitrates, potassium, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and triggers differential settlement. If the settlement is great enough, the geo-membrane tears, the leakage increases, triggering more differential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will undergo a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geo-membrane with suitable flexibility under axi-symmetric (multi-axial) load conditions to tolerate the predicted settlement. (This paper was previously published for Randol Gold Forum 1996 [Ref. 6]).

Jan 1, 1997

By Caibin Wu, Chengfang Yuan, Jiaqi Tong, Zhilong Cheng, Ningning Liao, Chong Zeng

In a series of Julius Kruttschnitt size-dependent breakage models, the cumulative percentage passing 1/10 of the initial size is used as a fineness indicator for scientific research and the selection of grinding equipment. However, in industrial practice, it is quite customary to use the mass percentage passing 75 μm as the indicator. In this paper, based on the energy-particle size model, quartz and calcite, two materials with distinctly different hardness, were used as test samples in a conical ball mill. At the same specific energy, the value of the cumulative percentage passing 1/10 of the initial size decreased while that of the mass percentage passing 75 μm increased with finer feed size. The experimental test values of the mass percentage passing 75 μm have a good linear relationship with the model predictions, which suggests that the particle size energy relationship of the mass percentage passing 75 μm and Ecs can be used instead of the cumulative percentage passing 1/10 of the initial size and Ecs. By building family curves, when particle size x < 300 μm, the family curve can be well fitted, and the fine particle size distribution of the whole product can be reconstructed.

Dec 22, 2022