Search Documents

By Dennis Z. Mraz, Maurice B. Dusseault

INTRODUCTION In 1982 and 1983, as part of the mine design program for a New Brunswick potash mine, series of laboratory tests were conducted on potash and salt samples obtained during the mine exploration program. Concurrently, two rock mechanics monitoring programs were initiated in-situ the short term test at site A, and the long term test at site B (figures 1 and 2). SHORT TERM TEST (FIGURE 1) The purpose of this test was to obtain a quick confirmation of laboratory data and comparison of the rock response to excavation with the data available from Saskatchewan potash mines. Instrumentation in the main drift was installed on Day 4 after excavation, and the pressure cells were pressurized on Day 33. The packer type cells in the east crosscut were pressurized on Day 25. Excavation of the west cross-cut was begun on Day 71. This "mine by" test has provided important information required for calibration of laboratory tests, as will be shown later. The test data recorded are shown in a series of diagrams: a. initial room closures, main drift-figure 3; b. convergence graphs, main drift-figure 4; c. stresses recorded, main drift-figures 5 to 8 and, d. stresses recorded, east crosscut - figure15 Three types of instruments were used in this test. In the main drift. Saskatchewan Research Council water type hydraulic inclusions. encapsulated in potash, were used to measure lateral and vertical stresses. In the east crosscut a home-made packer type hydraulic inclusion was used to record radial stresses. The convergence stations consisted of end-grouted bars of reinforcing steel. LONG TERM TEST (FIGURE 2) The purpose of the long term test was to study the steady-state behaviour of a single opening in potash. Site B was placed in a remote area of the mine, well away from any anticipated early mining activities. To assure homogeneity of rock mass, the site was placed within a 30 meter thick vertical limb of a syncline-shaped ore body contained within a 360 metre thick vertical section of salt rocks. It was excavated mechanically as close as possible to the designed square cross-section for the entire length of the room. The square cross- section was chosen in order to achieve a comparable geometry in vertical and horizontal directions; that is, to eliminate any undesired effects of geometry interaction with lithostratigraphy which might have generated non-homogeneous behaviour. The site was extensively instrumented. As in site A, the convergence stations consisted of end-grouted bars of reinforcing steel. However, in order to avoid any measurement inaccuracies which would be associated with the brittle yield zone in the opening walls, bars were placed to the same depth in opposite sides of the opening. This allowed the convergence measurement to be obtained as the absolute convergence between two points, rather than the convergence of a single point with respect to a potentially unstable reference. For stress measurements the Saskatchewan Research Council cells were placed vertically, laterally and radially. Unfortunately, due to cost considerations, it was decided to use a compacted sand, rather than grout, to encapsulate the cells in the boreholes. Due to the extremely small strain rates, only radial ly placed cells could be adequately pressurized. The rest of the cells did not perform adequately, and are currently being replaced.

Jan 1, 1986

By Eugene R. Palowitch

From the late 1880s to the present, the Appalachian region continues to be a dominant supplier of premium-quality coals. The region contains an estimated 93.4 Gt (102.7 billion st) of demonstrated reserves in Alabama, eastern Kentucky, Maryland, Ohio, Pennsylvania, Tennessee, Virginia and West Virginia. Therefore, Appalachia will remain a source of quality coals for the metallurgical, export and utility markets. Figure 1 shows the annual production of coal in Appalachia and nationally from 1970 through 1993 (Energy Information Administration, 1994). During that 23-year period, annual domestic coal production almost doubled. Coal production from Appalachia increased at an average annual rate of only 0.7%. Coal production remained essentially constant at about 409 Mt/a (450 million stpy). Thus, Appalachia's market share decreased from 69.8% in 1970 to 47.2% in 1993 - a drop of almost one-third (Energy Information Administration, 1994).

Jan 1, 1995

By J. M. Wempen, M. K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique capable of measuring centimeter-level surface displacement with high spatial resolution over large areas. Regular monitoring of subsidence due to underground mine development is one potential application of DInSAR, and in this study, the application of DInSAR for subsidence monitoring is evaluated for two mining regions in the mountain west of the United States. In general, DInSAR has potential to identify the shape and extent of subsidence; in some cases, magnitudes and rates of subsidence can be defined. Importantly, the effectiveness of DInSAR for subsidence monitoring depends on the radar band (wavelength), the subsidence rate and the time between image acquisitions, and the topographic and vegetative surface characteristics. INTRODUCTION Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote technique that can be used to measure small surface displacements. Under good conditions, centimeter-level displacements can be measured with subcentimeter accuracy (Buckley, 2000; Massonnet and Feigl, 1998). Additionally, DInSAR data have relatively high spatial and temporal resolutions. Pixels in Synthetic Aperture Radar (SAR) images can have a ground resolution as small as about 3 m, and images often include tens to hundreds of thousands of pixels and cover tens of kilometers. Regions are imaged regularly, and periods between images typically range from weeks to months. In DInSAR, phase measurements from two radar images acquired over the same region at different times are used to precisely measure relative distances (Rosen, 2014). Surface deformation, topography, and changes in the satellite position all contribute to differences in the length of the path that the radar wave travels in each image. SAR sensors use radar with relatively long wavelengths; L-band (24 cm wavelength), C-band (6 cm wavelength), and X-band (3 cm wavelength) radar are used most commonly. Because the wavelengths are long, small changes in the path length of the radar signal can be quantified by measuring the change in the phase of the radar signal between the images. In general, changes in the path length due to changes in the satellite position and topography are known or can be estimated, and centimeter-level changes in the path length due to deformation are measurable. This study evaluates the effectiveness of DInSAR for measuring subsidence in two mining regions in the mountain west of the United States. L-band data from the Advanced Land Observing Satellite (ALOS) and X-band data from the TerraSAR-X mission are evaluated. Imaging characteristics, including the radar band and the time between image acquisitions, are important for effective subsidence monitoring."

Jan 1, 2017

By P. O. Lindahl

The U.S. Bureau of Mines initiated research to improve the safety and efficiency of transporting coal from deep underground mines using a balanced air-lift hydrohoist. A 50-m-high pilot-scale model was constructed and tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a U-tube pipeline from the mine level to the surface with the assistance of compressed air. A prototype screw feeder is used to continuously compact and inject 5-cm or less run-of-mine coal into a pressurized 20-cm-diam pipeline. Production rates up to 40 metric tph at an airflow of 1.5 m3/min were achieved with the model, and coal size degradation was relatively minor. Modifications are in progress to achieve 100 tph at an airflow of 2.8 standard m3/min injected into the riser pipe. Pilot-scale results indicate that an air-lift hydrohoist system is a feasible, cost-effective alternative to conventional skip hoisting that can be installed in existing shafts or surface-drilled holes closer to the face area. Air-lift hydrohoisting offers advantages of infinitely adjustable slurry flow rates, reduced pressure at the point of coal injection, and flexible design that can be combined with hydraulic pumping. Proposed design changes are discussed for coal transport, mine layouts, ventilation, fire control, and escapeways using this system.

Jan 1, 1995

By S. Behl

A major limitation in developing successful selective flocculation schemes is the difficulty encountered in adsorbing the polymeric flocculant only on the desired substrate. In this paper a correlation between selectivity of flocculant adsorption and separation efficiency is outlined and a potential technique to achieve selective adsorption of flocculants is discussed.

Jan 1, 1992

By P. Zhang

Phosphate mining in Florida generates approximately 100,000 tons/day of phosphatic clays (slime). This waste slime not only creates one of the most difficult disposal problems in the mining industry, but also causes tremendous loss of P2O5. About 20-30% of the phosphate mined end up in phosphatic clays. Recovering the phosphate from this waste is difficult for two main reasons: 1) the slime is extremely fine in size, and 2) clay minerals account for almost half of the material. A half dozen dispersants were evaluated for keeping the clay minerals suspended for subsequent separation from non-clay minerals by either settling or cycloning. The separation efficiency and economics are discussed.

Jan 1, 1998

By M. Y. Fisekci

Subsidence measurement methods, applied over the thick and steep seam mining in the Rocky Mountains Region of Western Canada are described. The studies to date indicate that two new subsidence monitoring techniques appear to be the most suited methods for our conditions. The computerized telemetry and aerial photogrammetry systems are being tested for the reliability of the systems during the winter months within the network of laser surveying over the workings of the new hydraulic mine. The site particulars and the mining method of the concerned area have been described briefly. The observation over the old hydraulic mine indicate that panels adjacent to each other do not obey identical subsidence phenomenon.

Jan 1, 1982

By D. W. McGlashan

[Becaune ad ;the extennive nwrgace anea od u.X chopRex2 in emmiom, emuhion dRokdtiun oddeh poaaibWa don ;the necove/ry ul; BinQey divided minmcd pa~LL&a, Swr~aC;tavu% mu2 akab&ze ;the emu-bion and poan an an ad~i&y don ;the dahed mina&. OZhm hpohtant acto oh me ;the naAwre od ;the em&iun inghedied, ;the nQRaLLve volwna 06 the colz;tinuoun and dincon;tinuoun phaa, ;the change aign bonne by the dnuplm ad the o.X phae, ;the z&a pu;tenticd od ;the dahed minmd, the ~olubRe am curdent 06 khe wcr;ten-pulped and gnuund onu. AX on nem ;the AoQRec;trtic point on ZPC, ;the doubRe Raym about ;the minW-&den oil dnopR& i~ neduced in ;tkichnaa and the dn_opR& wU codace and continue to aggnegate into agglommaka . Invetmion dnom O/U ko W/O can UCCWL depending upon a nwnbm a 6 in;tmQeaked daotuh~. EReothokin&Lc inn&wnenta;t/iun to meanwre ;the ZPC, QReckProphonQkic mobilXty z&a pokeW and hakerning cuttrtent me invcduabte in ;the appficatiun ud emu-bion dRo;tat;iun ;to m&~c and nonm&~c minu.&. ] INTRODUCTION Recent interest in emulsion flotation can be ascribed to the necessity of selective separation and concentration of extremely fine minerals. That which follows is an elucidation of the many factors-in emulsion technology in application. In applied surface chemistry for solid-particulate separation and concentration, emulsion flotation is one of the intermediate processes between froth flotation, in which the continuous phase is water (99.5 to 99.999% by volume), and particulate extraction, in which the continuous phase is almost entirely an organic-fluid. Another intermediate process is particulate exchange (or partition) in which immiscible or very limitedly miscible phases are in controll¬ed but appreciable volumes. Surfactants are common to all of these

Jan 1, 1968

By Winn B. Frank

Events of the mid-1970's have materially affected US coal production and transportation by railroad. Coal, as a replacement or substitute for petroleum fuels, has been hauled in significantly increased tonnages. Concurrent with the new demand, the railroad regulatory environment has undergone major changes, especially in "deregulation" activity. Those two events have produced considerable Litigation regarding coal rates. This paper discusses the factors involved with railroad rates and topics such as revenue adequacy, Ramsey Pricing, stand-alone cost, and differential pricing. In addition, an update on the western railroad merger situation and the implications for coal transportation are presented. The paper concludes with an evaluation of the current regulatory climate and future prospects.

Jan 1, 1983

By M. R. Peterson

The U.S. Bureau of Mines has investigated new methods for increasing the selectivity in flotation by creating and regulating reagent concentration gradients within flotation columns at steady-state operation. Gradients were generated and traced in a water-only system with the use of fluorescent dyes, and the effects of various operating parameters on these gradients were investigated. From this investigation, it was found that both gradual and steep gradients could be generated in the froth cleaning zone, and that these gradients could be changed through the manipulation of both physical and chemical operating parameters. The application of reagent-gradient control to mineral systems could improve both flotation grade and recovery in commercial flotation operations without the use of additional flotation circuitry.

Jan 1, 1992

By Saurav Kumar, Akshay Kumar, Vinayaka R. Kiragi, M. K. Banerjee, Amar Patnaik, Vinod Kumar

Today’s industrial technology offers to optimize and reutilize the resources available in terms of scum that remains after hot rolling in steel rerolling mills in Rajasthan, India. Vast reserves of low-grade coal exist and tons of mill scale are produced everyday after hot rolling in steel rerolling mills in Rajasthan, India. The present research work aimed to optimize the various parameters of solid-state reduction of mill scale using low-grade coal from Rajasthan, India. This study investigates the effect of reduction temperature (850–950 °C in steps of 50 °C), reduction time (60 to 180 min, in step of 60 min), mill scale size (800– 300 μm), and mill scale to coal ratio (1:1, 1:2 and 1:3) on achievable metallic iron percentage and its metallization. A higher percentage of iron content is obtained at a lower particle size of 300 μm. The structural analysis is carried out on 300 μm mill scales using XRD analysis, which shows the percentage of iron is approximately 63%, and metallization above 80% can be obtained under the reduction temperature at 900 °C for 180 min, for 1:3 ratio (mill scale to coal ratio). The chemical composition of the mill scale is obtained using X-ray fluorescence (XRF), and particle sizes as well as distribution of mill scale are determined by scanning electron microscopy (SEM). The elements present in the mill scale are also verified using EDS, which indicates the presence of a major portion of Fe, followed by Fe2O3, Si, and C, respectively.

Aug 14, 2020

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates.

Jun 13, 2021

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

By R. L. Sundeen

Trackless vehicles, as the name implies, are machines not bound to rails, guide cables, or other direction controlling devices. They include, for the most part, vehicles which are wheel or crawler (track laying) mounted. Power sources may be self contained such as diesel or battery and can be defined as non-captive machines, while connected power sources such as compressed air or electric can be defined as captive machines. Trackless vehicles are used in all phases of underground excavation, loading, hauling and dumping. Early application found most machines with digging ability used to load those with payload hauling ability. As the versatility of trackless methods became more obvious the trackless vehicle has evolved to more productive machines such as the self loading haulers commonly referred to as Load-Haul-Dump equipment. Trackless vehicles find wide use in drifting and tunneling. Ability to negotiate adverse grades is especially noteworthy. Experience drawn from highly efficient room and pillar mining operations has lead to relatively wide application in drawpoint and cut and fill mining.

Jan 1, 1969

By T. C. Canter

Technological change is continually affecting the mining industry and the many papers being presented at this meeting reflect this fact. I fully agree that miners must remain fully cognizant of technology that can change mining costs and therefore your competitive marketplace. Despite the embrace of new technology and effective mine management techniques, the mining enterprise may not realize increased net income if the structure of the minerals marketplace is not understood. An important segment of the marketing structure for minerals is transportation. Transportation costs per ton can be much greater than the mining costs per ton and may accordingly overshadow hard earned gains in productivity. Change is greatly affecting the transportation industry but the change is driven more by governmental policy than technology. Although some technological advances are occurring in the bulk transportation business, the changes I want to address arise from policy. Policy changes have come from legislation in the 1970's culminating with the Staggers Act of 1980 and ensuing Interstate Commerce Commission decisions.

Jan 1, 1985

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase the capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont Mining in Nevada was faced with such a need in its carbon-in-leach (CIL) train. In a collaborative effort between Newmont and Derrick Corp., tests were conceived to assess the viability of drop-in replacement screens using a three-dimensional screen panel. The synthetic pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade its urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing and other scalping applications.In spring 2014, Process Machinery Associates (PMA), Derrick’s local area representative, met with Newmont to discuss the operation of the in tank screens in the CIL train at Twin Creeks, near Golconda, NV. The process was originally designed for about 12+ kt/d (13,000+ stpd) but the throughput has been steadily rising since the plant was commissioned. Newmont now requires 14.5 kt/d (16,000 stpd) to be processed. The original screens were running at their maximum capacity, and Newmont required additional screening capacity to continue the upward trend in production.Physical separation by use of screening is one of mineral processing’s oldest methods. Screening media can be prone to blinding and pegging, and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and, thus, larger machines, screening media that does not blind or a combination of both.In an effort to avoid larger machines, Derrick had been working on a revolutionary threedimensional panel that would add nonblinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 in July of 2013. It was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By G. Piegols, J. A. Lombardi

Substantial volumes of cyanide are consumed in precious metals mining due to the purposeful destruction of base metal cyanide complexes and free cyanide to meet surface discharge regulations. This destruction of cyanide resource runs counter to the prevailing social ethic of resource conservation wherein cyanide recovery-and-reuse is considered a more socially responsible cyanide use pattern than systematic cyanide destruction. HW Process Technologies, Inc. (HWPT) has developed membrane based methods for the recovery of cyanide from barren solution as a means to reduce cyanide waste. The HWPT Engineered Membrane Separation (EMS™) system uses state-of-the-art spiral wound membrane elements that are engineered specifically for the treatment of high pH cyanide process solutions. The membranes fully reject WAD CN, SAD CN and most minor metals, and partially reject SCN, Free CN and precious metal cyanide from a high clarity barren solution feed to a small volume EMS™ “concentrate” stream. The EMS™ “concentrate” stream is returned to the process. The large percentage of the EMS™ process feed exits the system as cyanide lean EMS™ “permeate.” The EMS™ permeate, after residual cyanide destruction, polishing, and pH adjustment, is, thereafter, typically suitable for discharge. Separately, the HWPT EMS™-PLS method of cyanide recycling is an internal plant cyanide recovery step that removes base metal cyanides from a pregnant leach solution to a small volume EMSTM concentrate stream. The concentrate stream is then typically processed further for the recovery of metals and recovery-recycling of cyanide. The method makes it economically practical to recover gold from Merrill-Crowe or car-bon plant “fouling” solutions, e.g., those with greater than 400 ppm Cu, as might result from the use of the EMS™ method wherein EMS™ concentrate is constantly thrown back into the mine leach solution pool as part of the free cyanide recycle process, or as might result from the single-pass leach treatment of high copper content ores or concentrates. The EMS™ cyanide recovery method for barren solution treatment is shown to be “economic” for the treatment of clear solutions at the approximately 200 ppm total cyanide level (CNT), and for slurries at the approximately 400 ppm total cyanide level, where economic is defined as a 2 year EMS™ plant payback. The EMS™ plant payback calculation includes the beneficial monetary impacts of gold and free cyanide recycling and the avoided operating cost of cyanide destruction.• The cyanide recovery plant payback period is reduced further when the avoided capital costs for cyanide destruction (EMS™ permeate “clear solution CN destruction polish” only required) and/or metals precipitation are considered.

Jan 1, 2004

By Amoussou Coffi Adoko, Shevaune Zeng, Sebastian D’Hyon, Gareth Kennedy, Eleonora Widzyk-Capehart

Inertization of coal dust with stone dust is a common control implemented within underground coal mines to mitigate the hazard of a coal dust explosion. To achieve adequate inertization, the total incombustible content (TIC) of the coal/stone dust mixture is required to meet certain percentages depending on the risk and relevant legislation. Current methods for determining the TIC of a mixture involves laboratory analysis, colorimetric comparison, or the use of portable instruments. This paper provides preliminary analysis of determination of a sample’s TIC in real-time with chemometric modelling, using portable instruments employing near-infrared (NIR).

Feb 1, 2024

By Emily Sarver, Cigdem Keles, Jonathan Gonzalez

The study re-examines respirable coal mine dust samples using scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). It finds that SEM tends to overpredict the abundance of dust from rock strata and underpredict coal content, possibly due to coal-mineral microagglomerates (MAGs). The findings suggest that MAGs could be valuable in improving dust controls in mines.

Feb 10, 2022

By Richard Campbell, MEHMET KIZIL, Ismet Canbulat, Serkan Saydam

The design and effectiveness of ground consolidation to regain stability of longwall faces vary widely and are often based predominantly on-site precedence or what were considered successful applications at other sites in similar situations. Little is known regarding product migration characteristics or change in rockmass conditions as a result of the application of consolidation chemicals. This paper presents the in-situ testing rationale designed and implemented recently across several longwall operations in the Bowen Basin, Queensland, Australia to provide quantitative measurement of the actual zone of influence of various resin injection products. Product migra- tion was physically measured by monitoring the change in rockmass temperature as a result of the exothermic chemical reaction of the various strata consolidation chemicals used. In conjunction with strata coring and Lugeon transmissivity testing pre- and post-injection to characterise the improvement in rockmass conditions due to consolidation product injection. The results of the testing programme, migration measurements, and rockmass assessment are presented, along with a discussion on how site- based Rock Mechanics Engineers can incorporate the data into the design of strata consolidation plans.

Jun 25, 2024