Search Documents

By D. Bhattacharyya

The adsorption and desorption of gold cyanide by activated carbon is significantly influenced by particle size of the activated carbon particles and the chemical environment. A series of adsorption and elution experiments have been performed with ten different particle size fractions. The tests indicate that although the ultimate adsorption capacity is independent of the activated carbon particle size, the adsorption rate is strongly affected by the particle size. Further, desorption characteristics using traditional Mintek and atmospheric Zadra procedures reveal interesting trends with variation in particle size and will be discussed in this paper.

Feb 23, 2014

By G. J. Joy, J. P. Rider

Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 30 m/min (100 fpm). This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the U.S. National Institute for Occupational Safety and Health (NIOSH) is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research (OMSHR) Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities — 152, 213 and 274 m/min (500, 700 and 900 fpm)— and at water pressures of 689, 1,034 and 1,379 kPa (100, 150 and 200 psi). Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Average reduction efficiencies of at least 90 percent were seen at the three sampling locations closest to the shearer for all three manifold systems at nozzle spray pressures greater than 689 kPa (100 psi). Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer, a spray manifold was fabricated and evaluated at an underground operation.

Jan 1, 2016

By Frank H. Buchella

Principal factors influencing equipment selection can be grouped into five basic categories. Tonnage Requirements, Ore and Waste Loading, transporting, and ground preparation equipment are largely determined by tonnage requirements. Generally, the greater the tonnage requirements, the larger the equipment size selected. Large size equipment is appropriate for a production of about six million tons (total) per month, medium size for three mil- lion tons, and small size for one million tons or less.

Jan 1, 1973

This paper reports on the behavior of mercury and its compounds during the thiosulfate leaching and recovery of gold. Thiosulfate solutions are shown to dissolve Hg0 and Hg2Cl2 to a similar extent as cyanide, but the leaching of HgS is significantly slower in thiosulfate solutions compared to cyanide. Hence, the use of thiosulfate may be an option for treating ores containing high levels of cinnabar, especially since the legislation concerning the discharge or sale of mercury is becoming more restrictive. The deportment of mercury during gold thiosulfate loading and recovery using a strongly basic anion-exchange resin was also studied. Although the mercury thiosulfate complex loads on the resin, the adsorption is weaker than for gold, with an equilibrium constant between gold and mercury of 51. Resin loaded with gold, mercury and copper was pre-eluted with thiosulfate (to remove copper) and eluted with a chloride and sulfite eluant. The majority of the mercury is eluted by the eluant and, hence, its deportment closely follows gold and the eluate would need to be treated to remove either mercury dur-ing or prior to gold electrowinning.

Jan 1, 2010

By T. E. Durney

In the Fall of 1987 The Wellmore Coal division of The United Company installed a fines separation circuit in its #20 plant near Big Rock, Va. The addition of the fines circuit included a bank of classifying cyclones and two flotation units; one a conventional 4 cell, 34 m3 Wemco cell, the other an 2.4 meter diameter by 7.6 meter tall, 28.3 m3 column flotation cell. The new fine coal separation circuit is depicted in Figure 1. The column flotation cell is manufactured by the Deister Concentrator Company, Inc., under the trade name Flotaire. The Deister Flotaire column cell utilizes a counter current flow arrangement and a different means of generating air bubbles than that of conventional mechanical flotation cells found in coal processing plants. Other features include diffusers for additional air supply and a froth washer. This cell is one of the few commercial scale column cells processing coal.

Jan 1, 1990

By Wladyslaw John Cieslewicz

Geologically, this region is occupied by Mesozoids, a folded belt of Triassic and Jurassic sediments and volcanics. Gold mineralization is of Upper Jurassic age. Most of the stream placers formed during the Quaternary. Placer gold was first discovered in 1916. Between 1930 and 1957, mining was carried out by the "Dal'stroi," a Russian death- camp organization. At the mines, "Dal 'stroi" exterminated 5-7 million captives taken from Russia's different colonies, each prisoner extracting 1-2 kg of gold before he died. Since 1966 the mines have been worked mechanically. About 10 mining districts are now active, producing altogether 110-135 tons of gold annually.

Jan 1, 1987

By James R. Dunn

The nature of water and clay in carbonate rocks is currently being investigated at Rensselaer Polytechnic Institute by various thermal and sorption techniques. Two basic concepts 'led to the present research. (1) To explain the expansion and contraction on wetting and drying of some unsound argillaceous carbonate rocks, it was postulated that the pore space around each clay particle is such that when water is sorbed by the clay, force is exerted against the pore walls. (2) The clays in expansive rocks are rejected from the growing dolomite crystals during their growth, and form a more or less connected network, thereby becoming "wettable," or available to water. New quantitative cold differential-thermal-analysis (electrocalorimetric) equipment was designed and constructed to check the "limited space" and "wettable clay" concepts and to determine the thermal nature of the transition of water to ice in rocks. This DTA equipment can detect the release of heat in freezing of less than 0.001 per cent water in a rock. Twenty-three rock cores (nine sound and fourteen unsound) and 4 procelain cylinders for standards were studied. In the nine sound rocks and in all the procelain cylinders, the rapid freezing of from 50 to 100 per cent of the water was readily detectable after 7 to 10° C of supercooling. No further freezing could be detected to -20° C. However, in eleven of the fourteen unsound rocks, no freezing was detected to as low as -40° C; in the other three, less than 50 per cent of the water froze. As a check of the DTA measurements, adsorption isotherms were determined for all materials. Calculations of theoretical freezing points for sorbed water again demonstrated that the least sound rocks had the most nonfreezable water. "Frost" sensitivity in these carbonate rocks is, therefore, probably not the result of the force of expansion of water to ice. The disruptive force is believed to result from expansion of sorbed, ordered water on clay surfaces. The relationship between the unfilled rock pores after 24-hour water saturation and the water sorbed at 85 per cent humidity at 30° C (i.e., the theoretical nonfreezable water delineates the sound and unsound carbonate rocks.

Jan 1, 1966

By P. R. La Pointe, H. C. Ganow

The production of both over- and undersized coal fragments is a constant problem to open pit operators in the Powder River Basin. Operators strive to achieve production blasts that economically minimize the weight percentage of over- and undersize coal. However, natural fractures influence blast fragmentation, and can impose limits on the final fragment size distribution. ARCO&apos;s Anaconda Minerals Company studied the limits placed by natural fracturing as part of a wider geotechnical study of the Wyodak Coal in the eastern Powder River Basin, Campbell County, Wyoming. Measurements of fracture orientation, size and spacing were made at ARCO&apos;s Black Thunder Mine. These data were used to form statistical distributions for natural fracture size, spacing and orientation. An algorithm was created to select fracture properties at random from these distributions and to form hypothetical blocks. The blocks were then numerically "sieved" to derive pos- sible particle size distribution curves. These curves are compared to fragmentation results from samples taken from three test blasts. All test blasts yield very similar lognormal fragment size distributions. The median particle size varies from 1.25 to 2.0 in.(3.2 to 5.1 cm), the mean from 4.0 to 8.5 in. (10.2 to 21.6 cm). The standard deviation was about 1.6 in. (4.2 cm). Coal fines (fragments < 0.25 in. or 0.64 cm) are about 15%. Calculated fragment distributions for the natural fractures predict the median size well but underestimate the variance. Algorithm modifications to account for processes known to occur in the comminution zone near the blast hole significantly improve the match in the fine coal size range. The match suggests that spacing of fractures, rather than fracture length, controls the formation of fine- and medium-sized fragments. On the other hand, the oversize coal is controlled by the fracture lengths, rather than the spacing. Data from subsequent test blasts support this idea. By increasing delay times from 8 msec to 17 msec, engineers were able to reduce fines to 7% - 10% but could achieve no further improvement, despite changes in shot pattern geometry, decking and hole size. The hypothetical fragment distributions show that, even without blast enhancement, about 5% of the natural coal blocks are fine-sized.

Jan 1, 1986

By N. R. Sainath

This paper discusses the results of a laboratory investigation carried out to study the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 1.5 and 4 inch diameter cores were mapped by visual inspection. The cores were stressed in a triaxial stress field representative of in situ conditions. The permeability of the samples to water was then estimated. The samples were exposed to 20 g/l sulfuric acid and the experiment repeated. The Permeability of unleached samples ranges from 10-1 to 10-19 m2 and it increases as leaching progresses. The porosity variation and the rate of recovery of copper from the specimen during leaching were also studied.

Jan 1, 1991

By K. Y. Haramy

A scale-invariant theory of the strength and deformability of rock masses in static equilibrium and at incipient failure is proposed. The theory provides a rationale for designing structures in rock. This paper presents results of experiments conducted by the U.S. Bureau of Mines and theoretical methods to determine and interpret in situ strength of rock masses using the borehole shear tester.

Jan 1, 1995

By A. Konya

"INTRODUCTION Underground Mining and Construction projects face several challenges unique to the underground environment compared to the surface environment. The goals of an effective blasting program are the development of a blast pattern that minimizes cost, maximizes face advance, and provides the desired fragmentation and face profile. In addition to these , mines must consider the very real operational problems that occur such as drill deviation, ground vibration, and deadpressing or sympathetic detonation of explosives. These operation problems lead to increased costs and decreased production in the mine, hurting the bottom line. Combined with these problems, underground blasts can be difficult to monitor and evaluate due to tight spaces, dust during the blast obscuring video, and the need to evacuate the immediate area with no clear line of sight to observe performance. This creates an environment which most mines know that blasting can be improved in their underground operations, yet most are hesitant to change due to fears of the shot freezing, misfires occurring, and questions about how to achieve a proper design. The explosive companies and shot service providers also offer limited assistance or knowledge in the underground blasting realm, unlike with surface blasting, leaving many underground operations in the dark. It is for these reasons that most underground operations are operating decades behind the current technologies and incurring significant costs, both real and hidden, from there blasting operations. This paper discusses philosophical changes to designs that need to be made for effective design and modifications of underground blast patterns to prevent deadpressing and precompression of modern explosive products (Konya, Konya, & Worsey, Modern Blasting Method Selection, 2017). While numerous different methods of underground heading development exist, there are two types that are used in a majority of mines around the world, these are the burn cut and the V-cut. The burn cut is a parallel cut that has holes that go straight into the face and are primarily used in smaller opening (due to ability to pull deep rounds with smaller room widths) and metal mines (helps in ore dilution and greater fragmentation). The V-Cut is a cut that uses angled drilling towards the center of the face (in the traditional method) and is primarily used in underground aggregate operations due to its cheap cost but larger fragmentation sizes and greater throw of the muckpile. This paper will discuss these two forms of cuts specifically with the understanding that modifications to these can be applied to other parallel and angled underground heading techniques. BURN CUT The burn cut is one of the older forms of underground blasting, where a part of the blast (burn) of a shot is heavily loaded with additional empty (relief) holes with the goal of smashing (aka burn) and pushing/blowing all the material in the burn out to provide relief for subsequent blastholes. The relief holes in the burn cut provide a parallel relief for the holes that are firing to break too creating a second plane of relief, however these are extremely small and can cause many problems if a design is improper."

Jan 1, 2018

By A. F. Grandt

What is prime farmland? Can such land, once it has been strip-mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on strip-mined land in St. Clair County (1). This research was done almost 30 years before requirements of Public Law 95-87 were passed by the United States Congress and signed August 3, 1977.

Jan 1, 1980

By Hayward B. Oblad

The effects of eight independent variables on froth flotation product yield, ash content, and coal recovery were studied using laboratory batch flotation of 0.6 am x 0 coal. The eight flotation variables investigated were air feed rate, pre-dispersion of collector oil, impeller speed, product collection time, initial solids concentration, collector conditioning time, frother (methyl isobutyl carbinol) concentration, and collector (No. 2 fuel oil) dosage. The two-level Plackett-Burman screening design and the three-level Box-Behnken design were used. Within the ranges studied, air feed rate had no effect on product yield. Pre-dispersion of collector oil, impeller speed, product collection time, initial solids concentration, and collector conditioning time showed only minor effects on the product yield and quality. Frother concentration (mg/L) in the process water and collector oil dosage (g/kg) were shown to be the dominant independent variables in coal froth flotation. Flotation experiments that vary initial solids concentration at constant frother dosage (g/kg) confound the effects of frother concentration (mg/L) and solids concentration. The dominating effects of frother concentration and oil dosage on coal recovery and froth product ash content are illustrated with three-dimensional plots. The relationship between froth product ash and coal recovery is also clearly illustrated by the flotation data.

Jan 1, 1985

By S. D. Bearden

China was the world’s leading producer of barite during 1995 with 35%. The United States followed with14%. India produced 9%. Other producers included Morocco, Turkey, Mexico and Germany. Domestic production of barite during 1995 was estimated to be 600 kt (660,000 st). Nevada produced 85% of the total. Georgia was the second leading barite-producing state. The United States is the world’s largest consumer of barite. During 1995, it used 1.6 Mt (1.8 million st). US reliance on imported barite during 1995 was about 63%of total consumption, according to the US Geological Survey.

Jan 1, 1996

By James Wonneberg, William Edgerton

"Today’s underground construction megaprojects are tremendous feats of engineering on a massive scale, excavating through ground conditions once thought impossible, using new and innovative contracting practices. But one important truth remains unchanged; projects are built by people. What separates winning projects from the rest? Great people, working in great organizations. In straight-talk fashion this paper sets forth fundamental differences between good project leaders and bad ones, on topics ranging from client relations, design management, and scheduling, to use of the whiteboard, and everything in between. Broadly applicable to all corners of project delivery, this paper will resonate with project leaders from around the world and help identify skills necessary to succeed in the management of underground facilities. A NOTE FROM THE AUTHORS This is a training document, and not really a “paper” per se. We have attempted to tackle some big and potentially complex topics using bite-sized paragraphs, each of which are intended to promote thoughtful introspection and dialog. So please feel free to skip around, or even set this document down while you reflect on your own personal experiences, tactics, and philosophies. We have found that providing examples of “what not to do” is oftentimes more instructive than simply listing “what to do”, hence the Good/Bad format of this document. Please note that “PM” refers loosely to anyone on the project management team not just the “Project Manager”. We also wish to preface this with the following cautionary statements: • The authors do not pretend to be the “Good PM” in all cases. In fact, we’re almost certainly the “Bad PM” for some. We aim to improve on those areas. • It has been said that “The only real training for leadership is leadership.” (Antony Jay) We all started somewhere, and nobody has 20 years of experience on day one. • Converting this text into some sort of prescriptive checklist would be a disservice to the evolution of project management. Our world – and our awareness of it – is constantly changing. We must always be open minded to new ideas and different perspectives on project delivery."

Jan 1, 2016

By C. E. Ekburg

Gold Quarry is a sediment-hosted, epithermal disseminated gold deposit located along the Carlin Trend. Gold, hosted by allochthonous Ordovician siltstones and cherts, is localized at the intersection of structures sympathetic to the major Good Hope and Gold Quarry faults. The magnitude of Gold Quarry was discovered in 1979 by surface exploration and by percussion holes drilled near the Maggie Creek orebody. Four years of development drilling delineated an open pit mineable gold deposit that contains 130 Mt (144 million st) of ore at an average 1.68 g/t (0.049 oz per st) of gold and includes a high-grade core of 46 Mt (51 million st) that average 2.64 g/t (0.077 oz per st) gold. Milling of the higher-grade portion began in 1985.

Jan 1, 1987

By Wendell E. Bearce

At the, Crescent Valley Mine of the Hanna Coal Company, several 10,000 ton unit trains of 41" x 0 strip coal are loaded per week during the lake season. This is accomplished without the use of any accumulation of prepared coal. A large raw coal pile is built up during the winter months adjacent to two truck dump bins. This is added to whenever trucks are coming in from the pits and trains are not being loaded. During the loading of trains, trucks from several pits dump into the truck hoppers and coal is also dozed in from the pile. At a rate up to 3200 tons per hour this coal is screened, the plus 6" hand picked, the plus 4" crushed, and&apos; all weighed and sampled as it goes directly to railroad cars being handled on two tracks by car retarders. With such an arrangement it is possible to exercise some control over coal quality, if it can be assessed rapidly. For instance, if the moisture rises to a level where it seems probable the BTU per pound will be reduced to the point where the contract calls for penalties, the trucks from, the wettest pit may be stopped, more or less coal may be moved in from the stockpile, or other measures taken to assure that the average BTU of the trainload will be satisfactory.

Jan 1, 1967

By J. R. Knudson

A major contribution to the art of blasting was made at the Cleveland- Cliffs Iron Company?s Hawkins Mine in Cashwauk, Minnesota during April of 1956. It was here that the first experiments with fertilizer grade ammonium nitrate were conducted-experiments which led to the development of the ammonium nitrate and fuel oil method of blasting which has been eagerly adopted by open pit and quarry operators throughout the United States. While this new blasting agent was a more or less natural outgrowth of the Akremite Process devised by Maumee Colleries of Terre Haute, Indiana; no one, to our knowledge, had used this particular combination of ingredients prior to this time. Certainly this was a "break-through" as far as the Lake Superior District was concerned. Akremite consists of a mechanical mixture of grained ammonium nitrate and a solid carbonaceous material packed in a plastic bag. At the time of its introduction to the Mesaba Range, Akremite sold for 10.5 cents a pound as compared to the 18 cent powder previously used in both wet and dry large hole blasting. The discovery of this agent was indeed a remarkable achievement, one that afforded a substantial reduction in blasting costs. However, Akremite proved to be only an intermediate step in the evolution of our present low cost explosives. Cleveland-Cliffs utilized prilled ammonium nitrate and fuel oil and then eliminated the mixing and packaging plant entirely by combining the two raw materials in the field at the drill hole collar or in the hole itself. Thus we have approached the ultimate in simplicity, for the blaster and his helper now manufacture their own explosives not only as they are needed but where they are needed, and at a cost of under 4 cents a pound. This two-man crew may charge and explode as much as 8 tons of ammonium nitrate in an eight-hour shift and in so doing break some 65,000 tons of ore.

Jan 1, 1959

By Mark R. Rybak, James Delmonte, Travis Hartman

The City of Phoenix, Arizona designed a 7.2 km (4.5 mi) long water transmission main from the South Mountain Reservoir to the Ahwatukee Foothills Reservoir to address the growing demand for drinking water in the southeast valley. The pipeline design called for a bored tunnel in a very environmentally sensitive area. The Reach3B contract included an 2.44 m (8 ft) diameter TBM excavated tunnel, 1,847 m(6,060 ft) in length. The geotechnical investigation revealed that the tunnel would likely pass through zones of loose to moderately cemented soils (caliche). The primary tunnel support would consist of rock bolts, circular steel ribs, hard wood lagging, and mine straps. A TBM that could handle the ground conditions and allow for efficient ground support installation was required. This paper describes the construction of a small diameter rock tunnel in challenging ground conditions.

Jan 1, 2003

In 1991, most industrialized countries, except for Germany, were in a recession or a period of reduced growth. The US economy, already in recession, suffered from mounting banking system losses and the uncertainty brought about by the Persian Gulf War. However, US and worldwide minerals exploration did not collapse as it did during the mid-1980s. Even though gold and base metal prices declined, prices were still above cash costs for most operations. This allowed the continuation of established exploration programs but sharply limited new initiatives. Exploration 1990-1991 Planned worldwide 1991 exploration expenditures declined by about 8% from 1990 levels, according to a survey of 153 companies by the Metals Economic Group (MEG). Canada was the leading exploration target with 23% of the total, followed by Australia and the US (19% each), South Africa (13%), Latin America (11%) and the South Pacific (7%). The remaining 8% was split evenly between Europe and the rest of Africa. In Latin America, Mexico and Chile are the most attractive countries for exploration. Recognizing the risks involved, the industry has been cautious about ventures in the former Soviet Union. Survey results also showed that while the majors expected to maintain exploration spending, smaller firms were cutting back or actively seeking farm-outs from the majors (personal communication, M. Wegener, MEG).

Jan 1, 1992