Search Documents

By Charles E. Dunne

One of the most frequently asked quesitons is: "Where is copper (price and usage) going?" I will not attempt to forecast either the future price of copper or the future growth of the copper industry; rather I would like to discuss the current trends experienced in the smelting and refining terms and conditions for sales and/or purchases of copper concentrates. A brief review of contract language and terms, together with a review of the common jargon, I believe, would be helpful. To accomplish this review, I will first list what I consider the four basic parts or sections of a basic ore contract and then illustrate basic terms with calculations.

Jan 1, 1984

By Ernest A. Draeger, James W. Collins

Water only cyclones, sometimes referred to as hydrocyclones, are one of the newest types of coal processing equipment. These devices have achieved wide acceptance as fine coal cleaners in the past decade. Many metallurgical coal plants employ water only cyclones to process 0.5 mm x 0 size coal. Some of these plants have as many as 40 to 50 305-mm-diam units with each unit receiving as much as 9 t/h of raw feed. The growth in the utilization of hydrocyclones is due partly to the energy shortage, partly to the general increase in over-all coal preparation, and also because of a need for a simplified fine coal (0.5 mm x 0 size) gravimetric separator. Large diameter water only cyclones are also available and in use to process feed sizes up to 32 mm in size. However, the size normally employed for cleaning 0.5 mm x 0 coal are 356 mm or 305-mm-diam for single-stage circuits. In two-stage circuits, the secondary units are normally the same diameter as the primary units or smaller, such as 203-mm-diam. By using the small diameter cyclones and treating a closely sized feed, 0.5 mm x 0 only, it has been found that the probable error or imperfection of the water only cyclones is comparable to that obtained on the same size fraction treated in a large 610-mm-diam heavy media cyclone washing 38 mm x 0. The water only cyclone can approach the efficiency of a heavy media cyclone when cleaning fine solids because it creates its own dense media by accumulating high specific gravity particles in the wide angle conical section of the cyclone. A cut-away cross sectional view of a water only cyclone is shown in Fig. 1. It is also true that when treating a wide range of sizes (38 mm x 0) in heavy media cyclones, the smaller size particles (0.5 mm x 0) separate in proportion to the split of the media through the cyclone rather than by particle density.

Jan 8, 1980

By P. Moyo, S. Dixon, R. Norcross

The separation and recovery of copper from cyanide solution has been investigated since the early 1900s. The precipitation of copper using sulfide ion was patented in 1911 by Williamson, published by Leaver & Woolf of the USBM in 1931 and Cyanamid in 1960s. The current practice of sulfide precipitation is used in various processes such as “SART" for cyanide regeneration and copper recovery. The precipitation of copper sulfide requires the pH of the clear solution to be in the range of 4-6. The precipitated copper sulfide can be sold to smelters. Alternatively, copper cyanide can be precipitated from clear solutions in the pH range of 2-3. However, selling copper cyanide is challenging because of its cyanide content. Past work has focused on the use of boiling sulfuric acid to convert copper cyanide to copper sulfate as published by Seracini in 1991. This paper describes a simple process to convert copper cyanide to copper oxide using sodium hydroxide at ambient temperatures. The cuprite can be sold to smelters or used as a feed to an electrowinning circuit to produce copper cathodes. The process provides an effective method to recover copper from cyanide solutions with a lower capital requirement.

Mar 2, 2022

By S. E. Phifer

The Haile Gold Mine was the largest gold producer east of the Mississippi River prior to 1942. It is currently the only producing gold mine in the Southeastern United States. Current development involves the mining and heap leaching of some 1000 TPD. Carbon is employed as a recovery medium. Due to its clayey nature and excessive fines in the oxide ore, agglomeration using Portland cement is required prior to leaching. The ore ranges in screen size from two inches to -200 mesh. The agglomerating step combined with certain other conditions has enabled Piedmont Mining Company to achieve recoveries of 90%.

Jan 1, 1987

By QU Hong-lue, YANG Lin-han

Aiming at the subjective impact caused by subjective weighting method in the establishment of rockburst risk attribute identification and prediction model, the combined weighting method was introduced to eliminate the influence of unreasonable weight of each index. Eight discriminant indexes affecting the risk of rockburst were selected. Through the literature review, relevant rockburst cases were collected and 8 index rockburst sample sets were established. A variety of machine learning methods were used to analyze the feature importance of discriminant indexes in the samples, and then to determine the objective weight values of different methods. Combined with the subjective weights determined by the Analytic Hierarchy Process, the combination of weights were successively carried out. Based on the attribute recognition theory, the combination weights with different objective weight methods were established to identify the rockburst risk attributes, and verified by the confidence criterion. The results show that the objective weight value determined by the feature importance analysis of machine learning reduces the subjectivity of the weight of Analytic Hierarchy Process method, improves the prediction accuracy, and makes the prediction result closer to the fact.

Apr 26, 2022

By J. Mastoris

The problem of defining the optimum final limits of an open pit mine has challenged the mining industry for the last three decades, mainly due to the great number of variables involved and the sheer computational effort required in real life applications. An actual lignite deposit is used in this study in order to introduce and apply a methodology to be used as a basis for surface mine design optimization. A geologic reserves model of the deposit is first developed with the use of an integrated geostatistical modeling package. The model is transformed into an economic one through the use of flexible objective function formulation(s). The optimization of the final open pit limits is then enabled with the use of a competent, commercial optimizer, and comparative sensitivity analyses are performed in order to study the effect of some basic mining and economic parameters on the optimal pit design. The conclusions drawn can develop useful guidelines for decision making by the mine operator.

Jan 1, 1995

By A. M. Gaudin

At the 1971 Annual Meeting we presented a paper on the results s obtained by wet magnetic separation on very fine, slightly magnetic material . Considerable interest was shown in a corollary subject, namely; on the type of magnetic con¬struction of the Magnetic Engineering Associates (MEA) high-intensity magnetic separator (HIMS). it is the purpose of this paper to describe the principles of this separator and to give answers to many of the questions directed at us both in session and privately since the March 1971 meeting of the AIME. It is well-known that passage of a direct electric current through a wire shaped in the form of a loop results in a magnetic field being created in the volume enclosed within the loop. The magnetic field is proportional to the amperes of electric current passing through the wire. If the wire is in the form of a solenoid consisting of 11 turns, the magnetic field is n times larger. Hence the expression ampere-turns commonly associated with magnetic separators. If a particle, free to rotate and of higher magnetic susceptibility than the medium, is placed in a magnetic field, it will orient itself within that field, and it will move within the field in such a way as to go into a more intense part of the field. The traction on the particle is proportional to its inherent magnetic property which depends on its magnetic susceptibility and its volume, to the mag¬nitude of the field at the spot where the particle is situated, and to the magnitude of the field gradient at that spot. Of the three factors that control traction on a particle in a magnetic field, the magnet designer can effectively control two, the magnetic field and the field gradient. In a wet magnetic separator such as the HIMS magnetic separator, there is another force exerting traction on the particle, and that is the force of the fluid (liquid) on the particle. It is, therefore, essential to examine the relationship of the fluid to the magnetic field. First, assume the water in which magnetic and non-magnetic particles are suspended to be stagnant. In the absence of magnetic field, the only forces acting on the particles are those due to gravitation on the particles and on the fluid displaced. This is the subject, so important in gravity concentration, discussed in elementary texts of mineral engineering'.

Jan 1, 1972

By Mustafa Kumral, Mehmet Balci

Strategic mine planning focuses on cutoff grade selection, capacity planning and block sequencing. Despite significant knowledge accumulated, potential value can be added to mineral sourcing by addressing various aspects. A case study on a metallic deposit with a lognormal grade distribution examines if grade/metal distribution influences cutoff grade selection. Six data sets with different shape and scale factors, but the same ore tonnage and metal quantity, are analyzed. Results indicate deposits with lower shape and scale factors are more sensitive to metal price and discount rate changes. The study also investigates the effect of economies of scale (EoS) on project value, focusing on the ratio of variable cost to total cost (capacity factor). Two regression analyses are conducted for optimal capacity planning and cutoff grade selection. The first shows capacity planning is highly sensitive to the EoS of mining and mineral-processing costs, with grade variability and metal distribution being negligible. In the second analysis, grade variability and EoS of mineral processing costs are vital for cutoff grade selection.

Sep 1, 2024

By I. Michalakis

A geological and geophysical study was con-ducted at the area of Stylos, Hania in order to study the possible mechanisms of saltwater contamination. A new detailed geologic map in scale 1:5,000 was combined with the results of a time lapse geophysical survey using seismic and electrical methods. A fault system in the N-NE direction possibly favors the saltwater intrusion.

Jan 1, 2006

By Michael Forbes, Rick Jeuken

The challenge of managing geological uncertainty in mine planning is central to optimizing resource extraction while minimizing risks and costs. This paper introduces a novel approach to coal mine planning by integrating chance-constrained programming to address the uncertainty inherent in mining operations. The main takeaway from this work is the demonstration that focusing on reducing the variance of high-quality coal blocks, rather than low-quality ones, can lead to better blending outcomes, higher profitability and more efficient resource utilization. The study presents a case study of a coal mining operation, using chance-constrained programming to manage the uncertainty surrounding coal property predictions, specifically the predicted coke strength after reaction (CSR).

Jan 1, 2025

By John B. Patton

No academic program of reasonable duration can provide a geologist with all the skills that may be needed for applied work in industrial minerals, but any curriculum that does not provide background in such basic subdisciplines as mineralogy-petrology, stratigraphy, sedimentology, structure, and geomorphology will leave the practitioner handicapped. Enough geochemistry to understand materials requirements, and sufficient geophysics to utilize geophysical data, are essential. In addition to purely scientific considerations, the industrial minerals geologist must be able to evaluate economic factors and may be faced with legal, social, and political problems in land use, zoning, environmental protection, and reclamation.

Jan 1, 1981

By G. J. Joy, J. P. Rider

"Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 100 ft./min. This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the National Institute for Occupational Safety and Health [NIOSH] is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research [OMSHR] Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities (500, 700, and 900 fpm) and at water pressures of 100, 150, and 200 psi. Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer a spray manifold was fabricated and evaluated at an underground operation. INTRODUCTION In 2012, underground coal mining in the United States produced a total of 342 million short tons, with longwall mining accounting for over 53% of this production [EIA 2013]. The longwall mining industry continues to see remarkable and significant improvements in longwall mining equipment and mining practices. Average shift production during compliance dust sampling has increased from 3,500 tons per shift in 1994 to approximately 6,000 tons per shift in 2012. A dramatic decrease in working longwall faces from 80 to 49 has occurred over the same period [Fiscor 2013]. Factors specific to longwall mines that supported productivity improvement include: higher capacity shearers, improved shield hydraulics and control, higher horsepower for equipment, wider face conveyors, and larger faces. Today, the average face width has increased to 1,188 ft., with one longwall operation reporting a face width of 1,650 ft. compared to an average of 750 ft. in 1994 [Fiscor 2009, 2014]. Panel lengths in 2013 averaged 11,307 ft. compared to 7,000 ft. in 1994. Overall production from U.S. longwalls has increased by nearly four percent from 2007 to 2012 with over 182 million tons mined annually [EIA 2013]. Given the volume and rate of coal produced on longwall faces, the potential to generate large quantities of respirable coal mine dust also exists."

Jan 1, 2015

By M. M. Fine

Development of a process for winning copper from pelletized chalcocite concentrate without matte smelting and converting is underway at the Twin Cities Metallurgy Research Center, Bureau of Mines. The new route from concentrate to metal includes 2-stage fluid-bed treatment; pelletized concentrate (33 percent Cu, 7 percent S) is first desulfurized (to about 0.5 percent S) in an oxidizing atmosphere, and in the second stage the calcine is metallized by reduction with hydrogen. Thereafter, the reduced product plus 10 percent CaO is routed to a smelting furnace to separate metallic copper from the gangue. Recovery and the Cu content of the product at this point are in the 97-98 percent range. The metal must be refined to remove sulfur and iron to make wirebar copper. An important feature of the process is the pelletizing of the fine concentrate into mini-pellets prior to fluid-bed treatment, which has permitted shorter reaction time, decreased dusting, and facilitated subsequent processing.

Jan 1, 1970

By D. A. Norrgran, J. A. Marin

Introduction The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980s provided a magnetic product that was an order of magnitude stronger than that conventional ferrite magnets. This allowed for the design of high-intensity magnetic circuits that operated energy free and that surpassed electromagnets in the strength and effectiveness. New applications and design concepts that focused on the mineral and metal processing industries have evolved. This technology led to the development of various magnetic separators specifically designed for mineral processing applications. Applications that were not previously considered are now being used in primary mineral upgrading, recycling and secondary recovery. Historical perspective Lodestone was the first naturally occurring permanent magnetic material known. Lodstone was most likely used to upgrade iron ore by early civilizations. By the 1600s, the early magnet technology had advanced to quench-hardened iron-carbon alloys. The practical significance of magnetic separation was formally recognized in 1792 when an English patent was issued for separating iron ore by magnetic attraction. By today's standards, carbon steel is a very poor magnet material. It is easily demagnetized and has a very low energy product of much less than I MGOe (Million-Gauss-Oerstads). This was state-of-the-art technology for almost 300 years until chromium was added to magnet feedstock, which resulted in a three-fold increase in the energy product. The well documented addition of cobalt to permanent magnets in 1917 initiated the 30-year era of "Alnico" magnets that at the time provided a superior magnetic energy product. Since then, the science of magnetism has advanced rapidly and is now considered a highly developed branch of physics and material science. Permanent magnets have had an extremely long history. Figure 1 presents a chronology of permanent magnets that illustrates the increase in energy product. Amazing developments in material science have taken place in the last two decades. The gradual advancement of permanent magnet technology was shattered in 1967 with the initial development of samarium-cobalt (rare earth) magnets. Since that time, the advent of neodymium-boron-iron magnets provided such an increase in energy product that new design concepts were considered. New avenues of study were introduced by the complexities in the material science and physics involved in describing these new permanent magnets. Furthermore, applications for permanent magnets that were previously not considered were now viable. Rare earth elements Rare earth elements have claimed the attention of scientists for the past century. These elements were originally termed "rare" because they were thought to be quite scarce. Since then, however, geological studies have shown them to be relatively abundant. The discovery and identification of rare earth elements is complicated by the inherent difficulties in separating them from each other. The rare earth elements comprise the fifteen transition elements of Group IIIB, Period 6, of the periodic table. These elements extend from lanthanum to lutetium and are commonly called the lanthanide series. Samarium and neodymium are the two most common elements used in the commercial manufacture of rare earth permanent magnets. Commercial grade rare earth magnets There are only a few common types of rare earth magnets that are considered in the circuit design for magnetic separators. Early rare earth magnets of commercial significance (introduced in 1970) consisted of the first generation of sintered SmCo5. The energy product of these magnets ranged up to 23 MGOe, which provided the initial impetus to the field of high-energy permanent magnets. Although these magnets did not produce the extremely high magnetic field strengths of current rare earth magnets, they were relatively temperature stable. Containing 66% Co, they are the most expensive of the basic commercial rare earth permanent magnets. Their use is limited today because they are being replaced by second and third generation rare earth permanent magnets.

Jan 1, 1995

By M. Wason

An Ore bed magnetic liner element is made of permanent ceramic magnets embedded in a rubber molding. (See figure 1) They are difficult and expensive to manufacture correctly. Therefore, the lining for a complete mill is expensive, as high as 400% more than conventional rubber liners. The magnets are not very resistant to impact as they are very brittle. Mills of 12 feet or more can use only I inch balls; mills under 12 feet can use balls of 1-1/2 inches. These liners are therefore used in regrind applications with small balls or in secondary pebble mills. Rubber liners for these applications last a long time, so if life was the only consideration, the pay back for these liners would be longer than the life of the mine. The Ore bed liner and its bed of ball chips or magnetic ore is relatively thin and the surface of this bed has a high coefficient of friction. The liners are made so that opposing poles are situated next to each other and that the mill shell and the bed of ore or ball chips completes the magnetic circuit. (See figure 2) The combinations of these properties results in a very efficient liner. Due to the low profile of this bed, there is no material that is lifted too high, so we have a very compact charge with very high attrition, good for fine grinding. These liners have shown a 10% ball consumption reduction and a 10% lower power draw for the same capacity. Due to the magnetic orientation, the bed is formed in a wave shape along the lines of magnetic force. Tests conducted at a copper mine in the southwest United States have confirmed these findings. The mills where the liners were tested are 10.5 feet by 16 feet Hardinge regrind mills operating as overflow ball mills.

Jan 1, 1999

By W. E. Lamont

As part of its program to minimize mineral and metal needs, the Federal Bureau of Mines conducted investigations to determine the feasibility of producing foundry-sand-grade olivine concentrates from low-grade sources. Using a Bureau-patented attrition-grinding technique, concentrates meeting Steel Founder's Society of America (SFSA) specifications for loss on ignition (LOI) were prepared. Studies showed that green strengths and tensile strengths of the attrition-ground olivine were equivalent or superior to those of commercial materials. Metal-casting studies showed that molds of attrition-ground olivine produced better surface finishes. The improved surface finishes were attributed in part to increased grain sphericity.

Jan 1, 1977

By Tony Dunn

FMC Corp. achieved a significant cost reduction at its Green River, WY soda ash operations using a new proprietary solution-mining and processing technology. In phase one of the program, trona ore is dissolved, recovered and processed with the new technology. It is then fed into an existing refining plant, replacing dry mined and calcined trona ore. Phase two produces a final high-purity product. It also increases capacity by 635 kt/a (700,000 stpy). Both phases were completed under budget and ahead of schedule. This $120-million expansion project uses a new process and a new team to derive soda ash in a more cost-effective and environmentally friendly manner. The team successfully introduced solution-mining technology - with a liquid solution injected into previously mined sections of the mine. This shift in techniques signified a new era for soda ash production. The project is an example of teamwork at its best. For it to be successful, FMC had to work within several different areas inside and outside of the company. Engineers, contractors, mechanical operators and technical people were needed who could blend in with FMC's existing in-house team.

Jan 1, 1999

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Jan 1, 1997

By R. N. Edwards

The Magnetometsic Resistivity (MMR) method is based on the measurement of the low-level, low-frequency magnetic fields associated with non-inductive current flow in the earth. The traditional resistivity method maps the electrical properties of the earth by measuring the electric field caused by galvanic current flow between a pair of current electrodes. The MMR method differs from it in that the potential electrodes are replaced by a sensitive coil or magnetometer and a component of the magnetic field due to the current flow is recorded. The presence of an inhomogeneity redistributes the current flow which results in a perturbation of the electric field and, usually, of the magnetic field. The electric field immediately above a relatively conductive inhomogeneity must, by Ohm's Law, be smaller than that expected for a uniform earth. The current density in this region is also reduced but the current density within the inhomogeneity itself is enhanced so that the horizontal component of the magnetic field measured above the inhomogeneity is usually larger than that expected for a uniform earth. A method of interpretation using the magnetic anomaly was patented by Jakoskyl in 1933 but it met with little success at that time. Part of the problem was undoubtedly with the instrumentation, and only recently have robust instruments of sufficient sensitivity been developed2 and field data of good quality obtained. There are many common configurations of the potential and current electrodes in the resistivity method. Similarly, in the MMR method one or both current electrodes may be moved with the magnetometer, either horizontally or vertically ( in a bore-hole), or the current electrodes may be maintained in fixed positions and the magnetometer alone moved. The MMR anomaly is defined as the difference between the

Jan 1, 1975

By Peter Ralph

All copper ore haulage at Isamine was transferred to the new 19 level haulage network by mid 1975. Previous experience together with design studies had indicated that a three train operation would be required to haul the scheduled ore production. The ore train with a gross weight of 600 tonne is made up of 15 bottom dumping trucks hauled by twin electric locomotives (Figure 1). Present train speeds reach 40 km/hr and, in the future, this speed could be increased to 55 km/hr. The planned operation on the restricted track network and the relatively high train speed meant that the train driver operated block light system would be inadequate on the grounds of haulage safety and meeting production targets. Some form of Centralised Train Control (CTC) system emerged as a necessity, and as an initial step, tenders were called for a relay control type CTC system. The high cost of these systems and the anticipated high maintenance costs and inflexibility of the offered systems led to the rejection of the tenders. It was decided to develop a CTC system locally and to use a digital computer to perform the basic track [ ] equipment interlocking tasks and monitor haulage operation.

Jan 1, 1979