Search Documents

By Jun Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1997

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By A. K. Gangopadhyay

This paper discusses the effect of grinding media composition, mineral type and slurry environment on the wear rate of various grinding media (balls). Sufficient wear data have been obtained and correlated with the modes of wear determined from examination of the ball surfaces using scanning electron microscopy. Five modes of wear have been identified to be operative under certain slurry conditions for the various ball compositions studied.

Jan 1, 1984

By Richard H. Olson

Talc deposits in the Precambrian of southwestern Montana (Beaverhead and Madison Counties) are unique within the U. S. A. in that large bodies of tremolite-free talc can be open-pit mined. All known deposits are in pre-Beltian dolomite units. The origin is suspected to be metasomatic, with the siliceous component having been contributed by an intrusive Precambrian granite gneiss. Precambrian deformation was extreme and is characterized by multiple periods of tight isoclinal folding and the flowage of less competent rocks, rather than by faulting. Post- Precambrian folding has been relatively negligible; the characteristic Laramide structure is block-faulting developed along northwest-southeast trends. The talc is thought to have been formed in Precambrian time; the high-angle block-faults probably have no significance with regard to the formation of the talc, but do tend to complicate mining operations. Tremolite-free talc ore bodies with horizontal widths of more than 200 feet, vertical depths of several hundreds of feet, and strike-lengths of as much as one-half mile are known in the Ruby Range and the Gravelly Range. Where dolomite is interbedded with tremolite-free talc in the Gravelly Range, the scale of this relationship permits the use of conventional open-pit mining methods with subsequent upgrading by hand-sorting techniques. Underground mining has been used in the past, but all current Montana talc-mining operations are on the surface. The hand-sorted ore, some of which is shipped overseas, is finely ground or micronized in roller mills and fluid-energy mills. The products are distributed both nationwide and abroad.

Jan 1, 1975

By Mohammad Ranjbar Hamghavandi, Mohammad Ranjbar, Zahra Manafi, Mohammad Hassan Fazaelipoor, Mahin Schaffie

The present study introduces a new approach to understand the copper dissolution rate and to find an adapted mathematical statement for particle shrinkage rate in a batch bioleaching system. Four size classes of a chalcopyrite concentrate, namely [D1 : (−54 + 44)μm, D2 : (−44 + 38)μm, D3 : (−38 + 25)μm and D4 : (−25)μm], were used in the batch bioleaching tests by applying a mixed culture of moderately thermophilic microorganisms. The pulp density and temperature were 8 (%w/v) and 50 °C, respectively. Findings delineated that the bioleaching time can be divided into two specific time intervals: first, the surface reactions were the prevailing controlling step; second, the prevailing mechanism was diffusion through the product layer, whereas the overall rate of the process may be related to both through a Q factor using a mixed model. A mathematical model was developed based on particle size distribution (PSD) and a kinetic model. Experimental validation of the mixed model was accomplished by the representative sample with d80 = 54 microns. Results showed that the PSD of the specific sample was in good agreement with Rosin–Rammler function. Besides, the simulation result of the conversion fraction had the best conformity with the experimental data (with a maximum error of approximately 7%). This paper should be considered as an initial part of a larger, global model for chalcopyrite concentrate bioleaching.

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 2,903 t (3,200 st) of ore per day, with an average gold grade of 0.4 opt. The mine’s horizontal extent is large, 762 by 152 m (2,500 by 500 ft), while its vertical extent is 6 to 61 m (20 to 200 ft). A high density of joints occurs within the host rock. Based on rock mass rating and field observation, the ground conditions at Leeville can be characterized as poor to very poor. As such, heavy ground support is required for its mining operation. Ore zones with a height in excess of 10 m (35 ft) are considered for longhole stoping. A typical stope measures 6 m (20 ft) wide, 30 to 55 m (100 to 180 ft) long, depending on the ground conditions, and 10 to 30 m (35 to 100 ft) high, depending the thickness of the ore body, yielding 9,100 to 18,000 t (10,000 to 20,000 st) when completed. Narrow ore zones, less than 10 m (35 ft), are mined using cut and fill. Drifts at the Leeville Mine are 4.6 m (15 ft) wide by 4.6 m (15 ft) high. Because of poor ground conditions at this mine, the establishment of a ground control monitoring system is key to operating both safely and successfully. This monitoring system is composed of comprehensive instrument design and installation. Instruments include multi-point borehole extensometers (MPBX) and “stretch measurement to assess reinforcement tension” (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two years’ application and measurement, useful data has been collected and continues to be collected; this information will be used to design future stopes and infrastructure. The system makes engineering and operation teams able to do their job with more confidence and efficiency.

Jan 1, 2009

By Robert Rennie, Taylor Davies, Ahsanul Rafi

Electric locomotives powered by extensive electrical cabling systems were prevalent in the mining industry in the early days of the 20th Century [1]. Since the movement of tethered electrical mining locomotives was limited, the advent of diesel-powered mobile mining equipment provided more flexibility. This led the mining industry to be dominated by diesel-powered locomotives for most of the 20th Century and the entire 21st Century, to date. However, diesel power has certain drawbacks. Diesel-powered vehicles produce tailpipe emissions such as diesel particulate matter, carbon dioxide, sulfur dioxide, and nitrogen oxide. Mine workers exposed to these emissions were, and continue to be, subject to health issues such as respiratory problems, increased risk of lung cancer, and cardiovascular disease. [2][3]. Extensive ventilation systems are required to dilute the diesel exhaust and dissipate the heat generated by these vehicles. Moreover, as mines are getting deeper due to depleting resources, ventilation costs in diesel-powered mines are becoming increasingly high. These factors, coupled with the trend towards greenhouse gas (GHG) reduction in mine operations, has allowed zero-emission electric locomotive systems to gain traction. As lithium-ion battery technology is becoming more advanced, battery-powered electric vehicles can now perform duty cycles comparable to those of diesel-powered vehicles. Although battery-electric vehicles (BEVs) are comparable to diesel-powered vehicles in terms of mobility, they have certain limitations. For instance, the amount of onboard energy is limited by the battery energy density and specific energy. The MT42 diesel haul truck from Epiroc, for example, has a fuel tank capacity of 580L, which is equivalent to around 1450 kWh of net electrical energy [4]. The electrified version of the MT42, on the other hand, has an onboard battery with 375 kWh of usable energy weighing around 4.9 metric tonnes [5]. Moreover, storing and refueling of diesel-powered vehicles is simple and quick, whereas battery energy storage and charging systems require extensive infrastructure development. Charging time is mostly limited by battery chemistry and design. Due to these limitations, the benefits of battery-powered mining vehicles are more likely to be realized with proper planning and optimization of the BEV fleet. This includes optimizing mining layouts for BEV use, charging infrastructure design, and management of onboard energy storage systems.

Jun 25, 2023

High pressure grinding rolls have found widespread acceptance for cement processing, and are now making their debut in the metalliferous minerals industry. Significant energy and wear material savings appear achievable in many applications. This paper re- views the technical literature on this important, emerging technology.

Jan 1, 1997

By R. K. Singhal

In 1990, Canada produced 69.4 million tonnes of coal of which some 65 million tonnes was produced by surface mining methods. The two Western Canadian provinces, Alberta and British Columbia produce approximately 55 million tonnes of coal by surface mining. These two provinces also provide the bulk of the metallurgical coal for export. The geological conditions in the Western provinces particularly in the mountain region are complex. The coals are friable and the seams are steeply inclined, sheared, intensely folded and faulted. There may be as many as 15 to 20 coal seams present with true thickness ranging from 2.5m to over 8m. Most of the Canadian surface mines are large (over one million tonnes per annum) using modern mining equipment such as shovels, high capacity trucks and draglines. At present the industry is going through another of its up and down cycles but has continued to make impressive gains in productivity. This has been achieved through greater mechanization, better management practices and a will to succeed in a highly competitive world market. This paper presents an insight into the current status of the Canadian Coal Industry and essentially updates the information given by the authors at previous SME meetings.

Jan 1, 1992

By R. Kent Comann

The sixth survey on the mining industry by Comann Associates provided data for entry-level and midlevel engineers as well as executive officers. Average 1989 compensation - base salary and anticipated bonus - for chief mining executive officers or chief mining operating officers: $237,943. This is an increase of 20% over the results of the last survey, on 1985 compensation. The latest survey also showed that bonuses for chief mining executive officers averaged 33% of base salary. Average 1989 compensation for chief executive or chief operating officers at mining operations with under $50 million in gross sales, $148,638; at mining operation with more than $50 million in gross sales, $275,141. The survey showed that these officers averaged 14 years employment with their present company, had five years in their present position, and had an average age of 54.

Jan 1, 1990

By R. J. Sweigard

Many states are considering the need to establish or modify policy relating to the disposal of coal ash. One of the primary concerns is the impact of leachate from the ash disposal sites upon groundwater and nearby bodies of surface water. A detailed site investigation was conducted at a coal ash disposal facility associated with a power generation station. The disposal site is situated alongside a major river. Monitoring wells were installed and soil samples were taken for characterization. Groundwater models were used to simulate migration of leachate from the disposal site toward the river. Such models could be used potentially to verify regulatory compliance. This paper addresses the validation and adaptability of these models to this case and their usefulness as possible tools to be used in future environmental audits.

Jan 1, 1992

By O. W. Kamper

To most of you present here the word "refractories" is not new and you are familiar with the materials and use. To many people though the question is asked, "What are refractoriness and what are they used for?" Refractories are non-metallic products which are so resistant too melting at very high temperatures that they can be used for building or lining furnaces of all kinds. A large variation occurs in the size, form, and composition depending on the service for which they are intended. They are made from a wide variety of raw materials, of which fire clay and quartzite are used in largest quantities. Other refractory raw materials include magnesite, chrome, diaspore, bauxite, kyanite, sillimanite, olivine, zircon, and many others. Most of these are assembled from-widely-'separated points in the United States while others come from the far corners of the earth. Chrome is imported from the Philippines and South Africa, and, to a lesser extent, Turkey and Greece Kyanite and sillimanite come: from India and bauxite from the Guianas. And there's "magnesite from brines," produced in chemical plant's by treatment of sea water or inland deep-well brines with hydrated lime. The proportion of magnesia available in sea water is so small, less than one pound from 500 pounds of water,, that millions of gallons must be pumped and processed each day in a sea water magnesite plant. The realm of refractory raw materials, therefore, is very extensive and continues to grow because of the endeavor to find-better raw materials from which to produce better products for refractory service.

Jan 1, 1960

By H. Walqui, J. Drelich, J. Pletka, E. Luhta, E. Raber, J. Wieland, P. Boyd, N. Tervo, D. Herron, S. Boston

Mini-projects studying the flotation chemistry of paper de-inking were incorporated to an educational program at Michigan Technological University with support from the paper recycling industry. Interfacial activity of frothing agents, surfactants and polymers in de-inking flotation systems has been studied through flotation, atomic force microscopy, zeta potential, contact angle, surface tension, and froth stability measurements. These fundamental studies were developed to understand microscopic and molecular effects occurring in flotation of ink particles that may lead to improved designs in de-¬inking flotation processes. Fundamental studies indicate that ethoxylated alcohols are efficient frothing agents in flotation and can be used to clean the recovered paper from hydrophobic ink particles. Next, it was further supported in this research that the fatty acids activated by calcium ions act as collectors in flotation of ink particles. Finally, improvements in de-inking flotation are reported in laboratory tests involving aqueous solutions of polymeric flocculants.

Jan 1, 2001

By Ehsan Moosavi, Kamyar Tolouei, Mehran Gholinejad

The literature defines rockbursts in slightly different ways based on their generation mechanisms, field phenomena, and degree of damage, but in a way that is almost consistent. Generally, a rockburst refers to seismic events that mainly happen in underground excavations, for purposes such as underground mining, road and railway tunnels, nuclear power, etc., and that are followed by the collapse and outburst of rocks. Long-term rockburst prediction can be abstracted as a classification problem mathematically, in which we can introduce deep learning to solve it. Further, using deep learning in rockburst prediction can overcome drawbacks such as subjectivity and inconsistency brought from previous traditional approaches. A rockburst data-set, was employed to evaluate the current method for predicting rockburst grade, and the good results of overall success rate were obtained. The results indicated that the proposed algorithms can speed up parameter optimization search, the proposed method is robust model and might hold a high potential to become a useful tool in rockburst prediction research.

Apr 26, 2022

By B. Qiu, Y. Luo

Longwall and/or room-and-pillar mining operations in multiple coal seams may not only induce subsurface and surface subsidence but also cause interactions between these mined coal seams. The interaction might destabilize underground mine structures and subsequently induce additional strata movements. Mathematical models to use the predicted subsurface deformations to assess the interactions and the consequences have been developed. The models are incorporated into a computer program, CISPM-MS, for predicting the final surface movements and deformations, as well as the mining interactions associated with multiseam coal mining operations. It predicts final surface movements and deformations caused by the individual mining operations and by the interactive effects. The program can also be used to assess mine structural stability in multiseam mining operations. The paper presents the developed interaction models and their application in surface subsidence prediction caused by multiseam mining operations. A case study involving mining in two coal seams, using longwall and room-and-pillar mining methods, respectively, will be used to validate the program.

Jan 1, 2013

By D. J. Tooker

For the next few minutes, I will be discussing a product and category that many people laughed at for years. The product is cat box filiers or commonly referred to by the brand name KITTY LITTER. This product was introduced in 1947 by Ed Lowe using the name KITTY LITTER. From 1947 to 1964 the product was sold mainly through pet shops. Starting in 1964, the grocery trade began to carry cat litters. From that point, the cate gory began a solid growth trend. Particularly in the '7O's, cat litter has experienced the same kind of explosive growth that has characterized the entire pet market. For example, in the twelve months ending 9/21/79, cat litter unit volume grew by 15% versus the previous twelve months. The basis for this explosive growth is easy to comprehend. The cat population itself is rapidly expanding, reflecting the changing life- styles of Americans. As famiiies grow smaller, there is room for a pet. As apartment and con dominim living shrinks living space, a cat fills the human need for animal companionship more efficiently. Table I illustrates current cat litter market factors and projects major trends into the future to conclude that the cat litter market will equal $205MM in 1985. With this dynamic growth defined, it was imperative that a company such as Lowe's that was totally devoted to the commodity-priced products, evaluate the opportunities for added- value product differentiation. This process was started approximately four years ago with a search for new cat litter products and other new product opportunities.

Jan 1, 1980

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

By S. M. Woodring

Research objectives included 1) determine relationships if any between spectral response of soil and soil textural groups, Unified Soil Classification subgroups and selected landforms and 2) develop computer assisted techniques for engineering soils mapping of remotely sensed data. The sire in northeastern Kansas, 1.6 Km by 43 Km (1.0 mi by 27 mi), contained glacial and alluvial soils. Multispectral scanner data (0.40 to 1.80 pm) collected at 915 meters altitude (3,000 feet) were analyzed using two distinct computer techniques: the nonsupervised approach involving delineation of soil training areas directly by computer and the supervised approach entailing training area selection manually by the researcher. Computer classification of surface materials follows both methods. Non supervised analysis results failed to show a consistant relation- ship between landform type and soil spectral class. Landforms correlating well displayed either unusually bright or unusually dark spectral signatures. Supervised analysis results showed a strong relationship between soil texture and soil spectral class. A moderately strong tie was shown between engineering soils groups (ML, CL, CH and OH) and their respective spectral classes, and a weak association between landform type and soil spectral class. An analysis procedure for engineering soils mapping by computer of remotely sensed data was developed. 1. Locate cultural features by visual examination of imagery. 2. Produce generalized bare soil-vegetation- water map using nonsupervised technique. 3. Outline significant soil fields for computer training using supervised approach. 4. Computer-classify entire area based on these soil fields.

Jan 1, 1974

By Kadri Dağdelen, Matthew Deutsch, Thys Johnson

Nested pit analysis in open-pit long range mine planning is used to define approximate ultimate pit limits and an initial high-level schedule in the early stages of a project. Modern ultimate pit optimizers can solve for dozens, or even hundreds, of nested pits however often a smaller subset of pits which are evenly spaced with respect to contained tonnage are desired for downstream analysis. In situations where that pushback selection process must be automated, such as when performing sensitivity analysis, or when the best subset of pushbacks is required; an optimization procedure is warranted. This paper describes a dynamic programming algorithm for selecting pushbacks following nested pit analysis, which is performant and addresses a long-standing inconvenience faced by long range open-pit mine planners.

Jun 25, 2023

By R. J. Sweigard

Deep tillage is used widely as a Means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage. A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids during deep tillage to prevent any significant recompaction from occurring. Various amendments were injected into the soil in the laboratory using a small-scale ripping and injection system. Measurements were made of selected soil properties to evaluate the feasibility of this method.

Jan 1, 1993