Search Documents

By R. J. McLaughlin

Acid mine drainage (AMD) can occur as a natural phenomenon through oxidation of sulfide minerals. Oxidation by air and water can be exacerbated by mining. Because AMD can exhibit low pH, it is capable of extracting heavy metals from mineral deposits. The result is highly acidic drainage with elevated heavy metal concentrations -the combination of which can cause extensive environmental damage. Because of the importance of these factors, this paper is focused on sulfate based AMD. Due to widespread mining, the occurrence of AMD is ubiquitous. As a result, several approaches to treatment have been developed. Chemical treatment using alkali is most commonly employed to treat AMD. There are alternative methods of treatment, as well as alternative ways of handling treatment sludges or concentrates. Dewatering of sludge or concentrates is beyond the scope of this paper.

Jan 1, 1996

By Peter Amelunxen, Brandon Akerstrom

Since its introduction 40 years ago, the compartmental model of flotation has been used to predict the performance of mechanical flotation cells. However, it has found limited success for modeling dual-chamber machines and, as a result, engineers have adopted empirical correction factors usually derived from field audits of industrial cells to predict the performance of dual-chamber flotation cells. This paper introduces an extension of the compartmental model that applies to both single- and dual-chamber cells. The model is tested against pilot test work performed at Capstone’s Pinto Valley concentrator, and then used to evaluate the key operating and design parameters of dual chamber flotation cells. The results suggest that the design of the mixing chamber — for example, whether it is pneumatic or mechanically agitated — is not a significant contributor to overall machine performance. The work also suggests that the highest recoveries are achieved when the froth recovery is high, and longer separation chamber residence times and/or higher internal circulating loads are only beneficial when the froth recovery is low. Lastly, the results show that the single most important driver of the machine performance is the froth recovery of the separation chamber.

Mar 1, 2025

By R. D. Hammett

This paper describes an investigation that MS carried out using the three-dimensional, stress analysis computer program "NFOLD" to assess pillar stability in relation to existing mining conditions and the proposed layout of future stopes. The stress analyses were designed to assess the present stability of the mine (particularly the pillars adjacent to the shaft), the change in pillar stresses as mining proceeds, and the optimum stope geometry to minimize ground control problems. The existing conditions were modelled first, and rock mass strengths were adjusted until a good agreement between the predicted and observed conditions was obtained. Analyses of alternative mining layouts, based on the calibrated rock mass strengths, were then compared. The paper describes the results and the conclusions of the study.

Jan 1, 1983

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The acoustic emission (AE) technology has a high potential for flow characterization in hydraulic transport processes. For instance, in deep-sea mining, there are applications where manganese nodules are transported from the bottom of the sea to the surface or a transport ship. Here, an AE-based flow characterization system plays an important role to avoid the transport of non-related objects. However, the structural materials for the components of this system must be carefully selected to ensure resistance against corrosion and a good AE signal transmission. Therefore, in this experimental study, we evaluated the AE attenuation behavior of four different materials that can be employed in marine environments due to their properties. The results were obtained using thin plates and they indicate which materials have the highest and lowest attenuations. Moreover, we provide insights regarding the different wave modes that propagate on the plates.

Mar 2, 2023

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, there are all of the following rock types: oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently; overblasting wasted drilling time, and explosives caused excessive throw. Several possible methods for improving the blast design were considered and a geophysical method was chosen for testing. There had been reports in the journals that seismic methods were being used in Europe as aids for blasting design. A literature search turned up work by Haxby 1/ on use of a refraction seismograph for measuring pit bench rock strength. Using his work as a springboard, equipment was purchased and a program was planned and carried out for developing, evaluating and implementing the seismic method for routine mine use. Following are discussions of the development program and results.

Jan 1, 1974

By A. E. Michon

I am Alfred E. Michon, Vice President- International for Burlington Northern Inc. I work for BN's holding company and my responsibilities include co-ordinating the activities of our eight subsidiary companies as they relate to international commerce--an increasingly important aspect of the overall business of our company. Until last April, I was President of the Fort Worth and Denver and Colorado and Southern railroads, subsidiaries of BN. Prior to that, I headed the marketing and pricing area of BN's coal transportation business. Based on my experience in the energy industry, both domestic and international, I would like to discuss the world-wide trend towards the reliance on low-sulfur coal in lieu of natural gas and oil for the generation of electricity. Since pontification on the energy scene world- wide is best left to consultants with scenario-spitting computers, let me in- stead emphasize this trend through two examples. First I will describe the regulatory and economic factors which have encouraged the replacement of natural gas by low sulfur coal as a boiler fuel in the US. BN's investments in track and equipment were instrumental in this conversion. Secondly, I will show how this same combination of factors has created a large demand for steam coal in the Far East. Again, our company's strategy is to facilitate conversion to coal overseas through timely and sufficient investments.

Jan 1, 1982

By James L. Evers

The development of hydraulic mining in the United States has had an uneven record of progress. The shifting of coal extraction from one government agency to another has not provided an environment for a focused national research program. This paper presents an update on hydraulic mining research in the United States. A comparison is made between the development of the technology in this country and the state of the art in other parts of the world.

Jan 1, 1983

By AK Raina

Blasting is used in mining and civil excavations to break the rockmass for ore production or creation of space. One of the disadvantages of the method is that it causes breakage beyond the proposed excavation lines. Pre-split is used to control such breakage in rockmass. This paper introduces the use of digital image analysis technique (DIAT) to measure rock breakage and half cast factor (HCF%). A new factor, undamaged area (AUD%), is introduced to improve the prediction, owing to the shortcomings of the HCF%. A comparison of significant data of AUD% and HCF% showed that HCF% has a lacuna of overpredicting, whereas AUD% can be used effectively to address the issue. Artificial neural networks are used to solve the complexity of multiple variables involved in predictions and to ascertain the importance and sensitivity of such variables in prediction regimes. This method will help users to evolve blast-induced damage objectively. A comprehensive scheme of things for future developments is included, which can be helpful to researchers in defining their research in this area.

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By D. E. Munson

The Waste Isolation Pilot Plant (WIPP) Project was established in 1975 by the Department of Energy (DOE) under Public Law 193 to develop the necessary technology for safe disposal of radioactive wastes from the defense programs of the U.S. The technology development involves extensive theoretical, numerical, and laboratory programs, as well as construction of the WIPP facility in southeastern New Mexico for in situ testing and waste storage demonstration. If after the demonstration, the facility is found to comply with regulations of the Environmental Protection Agency, then the facility will become a repository for Transuranic (TRU) waste. The underground portion of the facility is 655 m beneath the ground surface in massive natural salt deposits of the Salado formation, as shown in Figure 1.

Jan 1, 1991

By J. Drelich

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size and distribution of mineral inclusions in coal on its wettability are briefly reviewed.

Jan 1, 1999

By H. W. Newcomen, D. R. Brox

Assessments of the stability performance of open pit highwalls have traditionally been based on consideration of surface movement rates. Although generally accepted in industry, this approach presents challenges for establishing appropriate threshold values to allow for safe mining operations and does not address the issue of total strain. Surface movement monitoring data from a limited number of open pit mining operations in North and South America has been evaluated in terms of highwall strain, rock mass quality and inferred mechanism of instability. Threshold strain levels for key stages of highwall stability proposed from previous work have been reviewed and are generally endorsed based on evaluation of additional data. An empirical highwall strain criteria for the assessment of highwall stability performance is postulated based on the observed trends in highwall strain data from the case histories presented.

Jan 1, 2004

By Daniel Willis, Ryan O’Connell

An 8-foot tall horseshoe adit tunnel located within an abutment of the Mount Morris Dam in Mount Morris, NY required repair of a failed reinforced concrete liner. The adit tunnel is entirely founded within highly weathered shale bedrock units, which induced unloading stress on the original tunnel liner. An epoxy-impregnated carbon fiber fabric wrap manufactured by Sika was chosen to repair the failed adit tunnel liner. Kilduff Underground Engineering completed the design of the tunnel repair utilizing both empirical and numerical methods. Merco Engineering Contractors completed the injection of chemical grout and repair liner installation.

Jun 23, 2024

By Frederik P. Agterberg

Mineral exploration consists of the acquisition of data and their interpretation to ascertain the presence or absence of uncertain events. In general, the amount of uncertainty decreases during exploration when targets become increasingly well defined. Decisions on further exploration and whether or not mining should be commenced are based on new information using both objective facts and subjective reasoning. Computers play an important role during all stages of exploration. Three recent books (References 1-3) on decision-making in exploration and mineral-resources evaluation provide additional background supplementing the papers in this volume and articles in scientific journals or other conference proceedings (e.g., References 4 and 5) dealing with the subject. Other new developments to be considered are that microcomputers are becoming increasingly important in the earth sciences (Reference 6), and so are applications of artificial intelligence (Reference 7). Microcomputer- based technology allows rapid communication between field parties and main office. Expert systems are becoming increasingly sophisticated aids for mineral exploration an can now contain objective rules based on statistical theory (Reference 8).

Jan 1, 1989

By R. G. Dalbke

An increasing number of water pollution control systems are certain to be installed by many industries in the future because of new federal, state, and local government regulations, and because of the rising general concern about the deterioration of our water resources. Extensive engineering, some of it based on methods not yet developed, will be required if these new systems are to provide optimum pollution control. Capital cost, operating cost, and present and future regulatory requirements will be primary factors to be considered by engineers. This paper outlines procedures and gives examples of advanced engineering practices that have achieved efficient pollution control systems in the steel and nonferrous industries.

Jan 1, 1968

By John O. Marsden

"This article is an attempt to capture a presentation given at the 2016 SME Mineral & Metallurgical Processing Division (MPD) Luncheon held on Feb. 24, 2016, in Phoenix, AZ. It was presented as a tongue-in-cheek, lighthearted view of several of the issues facing our industry, while identifying some of the challenges and opportunities available to new engineers entering the industry today.Disclaimer• What you are about to read includes personal preferences, biases and occasionally arbitrary opinions.• Some readers may have dissimilar opinions on the contents and/or the rank order of the lists.There are eight top ten lists offered in this article: (1) Industry realities (2) Things a metallurgical or mineral process engineering graduate should do (3) Books every metallurgist should have on their shelf (4) Things I wish I had known (5) Legends of metallurgy (posthumous, with highlights) (6) Things we’ve forgotten (7) Mineral processing innovations of the past 20 years and, finally, (8) The future? For some items, additional context or clarification is provided after the item, while for other items no further explanation is warranted and none is offered. Top 10 industry realities1. Metal price cycles.2. Bigger is better (except when it isn’t).3. Ore grades declining across the board of metals/commodities.4. Ores becoming more complex.5. Three-fold increase in capital costs between 2004 and 2015.6. Three-fold increase in operating costs between 2004 and 2015.7. Less capital availability/challenging financial markets.8. Environmental constraints increasing.9. Socio-political constraints increasing.10. The mine manager is always impossible to work with.As Table 1 shows, there was more than a three-fold increase in gold operating costs between 2004 and 2014. The increases for copper, iron ore and other commodities were similar."

Aug 1, 2016

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union and the United States are summarized. Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1978

By G. T. Adel

The flotation behavior of a -28 mesh Pittsburgh No. 8 coal sample is investigated through the use of Scanning Electron Microscopy in conjunction with Image Analysis. Release analysis is used to generate the flotation products, which are then characterized to provide the particulate composition in terms of pyrite, mineral matter and carbonaceous material. The results of this investigation indicate that the material recovered in the first stage of release analysis tends to be well-liberated carbonaceous material. This is followed by an increase in the recovery of middlings and fines in the later stages of the process. Any free carbonaceous material remaining in the tailings from the release analysis test tends to be associated with the very fine sizes (-400 mesh). Pyrite recovery is attributed to the hydrophobicity provided by small inclusions of carbonaceous material, since the amount of truly liberated pyrite particles (i.e., 100% pyrite) present in the sample is found to be negligible.

Jan 1, 1994

By E. M. Frizzell

This paper addresses the use of the microcomputer programs BACKONE and BACKWEDG for an estimation of rock mass strength characteristics by back analysis of plane and wedge failures. The artificial support requirements are also determined by the programs PLANE2, BOLTPAT, and BOLTWEDG in terms of rock anchor installation angles, tensions, and installation patterns. These programs have been combined into a package called BACKPACK, which can be applied in open pit mines where some failures have already occurred.

Jan 1, 1988