Search Documents

By Richard E. Lounsbury

Coal mine refuse handling traditionally has been the redheaded stepchild of the industry - a problem to be ignored as much as possible. During the past few years, however, mining companies have become more aware of the potential water pollution problem associated with refuse handling and storage. Planning for refuse disposal increasingly emphasizes protection of the environment as well as economics of refuse handling. Coal companies are responding to the environmental control needs by devising new systems and adapting well-known techniques to refuse handling systems. Monterey Coal Company has operated a non-polluting refuse disposal system at its No. 1 Mine for over two years. The purpose of this paper is to describe the design considerations given to the planning of that system and the operational experience gained during its construction

Jan 1, 1973

By H. Russell, N. DePriest, J. D. Quaranta

Valley-fill structures built of blasted rock overburden from Appalachian mountaintop surface mines pose many reclamation challenges. The steep mountainous terrain, short valley lengths, and straight stream channel profiles create significant challenges to implementing fluvial geomorphic landform design in terms of both form and function, and from a safety and constructability perspective. The fluvial geomorphic landform design approach balances erosive and resistive forces by considering long-term climatic conditions, soil types, slope profiles and vegetation types. Commercial geomorphic landform design software tools do not specifically analyze the stability and factor of safety for the computer-designed landform slopes. This research investigated slope stability parameters and factors of safety between a traditional valley-fill design with a geomorphic landform alternative. Slope stability assessments were performed on two profile geometries. Finite-element modeling of a permitted valley-fill and a geomorphic design alternative indicated that slope angle and internal angles of friction associated with the gradation of the overburden greatly affected the designed factor of safety for both designs. The geomorphic designed slopes yielded the highest factors of safety out of 14 models analyzed with all cases having factors of safety over 2.0. The high factors of safety are attributed to shallow slopes and beneficial surface and internal drainage.

Jan 1, 2014

By Dr. Jack M. Gillette

A system of models which simulate surface coal mining operations has been developed for use in mine planning and economic evaluations. Micromodels simulate individual mine operations for equipment selection and mine planning. Macromodels simulate all operations in the complete mine for economic evaluation of reserves. A cash flow analysis model makes a complete discounted cash flow analysis to deter-mine a required coal sales price or return on investment for evaluation of any mining project.

Jan 1, 1978

By Niels Jonassen

INTRODUCTION The occurrence of the radioactive element radium, [2gg~a], often in trace amounts, in the crust of the earth gives rise to a flux of the daughter product radon, ['ii~n], across the earth-air interface. This so-called exhalation process has been studied by many investigators [KO 45, Kra 64, Pe 66, Wi 741] over several decades. In the earlier investigations the exhalation process was studied in a purely geophysical context, but over the last 20 years it has been realized, that under certain conditions the exhalation may be intense enough to also have radiological implications. This is for example the case where relatively radium-rich wastes or by-products, like uranium mill tailings and phospho-gypsum, are stored in larger quantities. In order to be able to predict the radiological impact on the environnent it is necessary to know the rate of exhalation of radon from the surface of the exhaling material. Usually the determination of these exhalation rates has been done by measurements in situ directly upon the accumulated material [~le 74, Ha 791. Although such field measurements have the obvious merit of dealing directly with the full scale problem, the results are often lacking in generality, making predictions for other situations difficult or even impossible. The present paper describes some results of an investigation where it is attempted from laboratory measurements on samples of limited size to obtain material parameters, which are suited for extrapolating and predicting the radiational behaviour of larger accumulations of the material. THEORY Let us consider a sample of a radon exhaling material enclosed in a container with a dead space volume, Vd, and initially containing radon free air. If the total exhalation rate (number of atoms per unit time) is c, the radon concentration (number of atoms per unit volume) N will initially grow with the time t according to the equation [ ] where [R] is the decay constant of radon. As the concentration (or activity) in the container grows, the net exhalation rate will slow down because of back diffusion, and, furthermore, radon atoms may be removed from the container, not only by radioactive decay, but also by diffusion leakage [JO 81 ]. If, however,only the initial. part of the activity growth curve is considered, the total exhalation rate, c, is given by [c = r•Vd(2) where r is the initial activity growth rate in the container. Let the container be cylindrical with an inner cross-section S and filled to a height L with a radon exhaling material with the specific mass p, the porosity E, the radon pore production rate f and the diffusion length i. When the container is left open,i.e. the radon exhalation takes place into a virtually radon free room, the radon area exhalation rate, E, can be written [Jo 80] E = Ef?t tanh L.R (3) assuming the exhalation only takes place in one direction, towards the surface of the material. It appears that for values of L > 2•ithe area exhalation rate becomes E a = Efi (4) independently of the sample dimensions and the total exhalation rate c is then c = E •S (5) For L ;~ 0.5•i, tanh P _ k and equation (3) may be written E ~ EfL (6) then c = EfL•S = p•m= Em •m (7) where m is the mass of the sample and Em = P (8) is the mass exhalation rate. It thus appears that the radon exhalation rate from a given amount of material may often be conveniently expressed by c = E •Sfor L z 2•I (5) a orc = Em •mfor L0.5•i (7) where S is the total exhaling area and m the total exhaling mass, E and E the area and mass exhalation rates respectively defined by equations (4) and (8).]

Jan 1, 1981

By Glenn Mongillo

Discrete Element Method (DEM) software has been successfully used to simulate various machine/soil interactions and provide insight for industries such as mining and bulk material processing. This paper will investigate typical calibration techniques used in particle models for DEM simulation and physical calibration experiments with soft ground TBM cutting tools to incorporate parameters such as tool drag forces that contribute to required TBM torque. With a well calibrated DEM model, it is expected that TBM simulation results will be more meaningful and provide better insight into TBM performance, power requirements, cutting tool placement, and overall cutter head design.

Jun 13, 2021

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

 This research project explored the viability of a new mining technology — thermal fragmentation — in narrow-vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation as well as one of an existing method used for narrow-vein mining. Comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs as well as increased productivity and ore recovery meant that the new method would improve the financial performance of any operation.

By L. Alan Weakly

The U.S. Department of Energy (DOE) has entered into a $l.5 million Cooperative Agreement with Alpine Equipment Corporation/Astro International Corporation ("Alpine") of State College, Pennsylvania, for the evaluation of water-jet-assisted (WJA) mechanical cutting of oil shale under actual mining conditions. A commercial-sized, heavy WJA mechanical miner is being assembled based upon the successful "factory testing" of a smaller prototype miner utilizing standard tungsten-carbide and Polycrystalline Diamond Composite (POC) bits in large oil shale boulders. Actual field testing of the machine will be conducted in an oil shale mine located in the Piceance Basin of Western Colorado. In-mine logistical support is being provided by several oil shale companies through the Colorado Mining Association (CMA) and the U.S. Bureau of Mines (USBM).

Jan 1, 1990

By JIACHENG XIE, XUEWEN WANG, QINGBAO BAO, ZEWEN YAN

The general application of memory cutting technology to shearers is improving the intelligence of the working face, but it has its limitations. It is only suitable for conditions where the environment of coal seam is changing slowly. It compensates for the cutting height by changing the fuselage attitude, and frequently adjusts the height to control the learning cutting trajectory, but due to the problems of shearer control and height adjustment accuracy, it cannot adapt to and compensate for the change of cutting height in a timely manner, resulting in poor cutting accuracy. This study puts forward a virtual memory cutting method based on prediction of the shape of the armored face conveyor (AFC). The integrated key technologies include generation of virtual teaching cutting curve, height adjustment strategy of front and rear drums, cutting

By Alan R. Johnson

Because of the competitive nature of the iron ore pelletizing industry, commodities required for the production of pellets are continually being scrutinized to minimize their usage and offset rapidly escalating costs. In the Tilden pellet plant, the usage of one commodity, bentonite, has been reduced from over twenty-four pounds per long ton of pellets to as low as eight pounds per long ton. The evolution of bentonite usage from plant start-up to the present time is described.

Jan 1, 1984

By J. Organiscak

A majority of continuous mining machines employ a water spray system and a machine-mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine-mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays and scrubber airflow on dust and gas levels, while using a 12.2-m (40-ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1-m (20-ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complement the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off-curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

By P. C. Thakur

The productivity in coal mines, measured in terns of the output per manshift depends largely on the efficiency and speed of men and materials transport between working faces and the surface. The mechanization of coal winning and material handling processes has led to a great rise in the mine productivity (1). Early applications of power in U. S. coal mines were mainly electrical. The excellent traction available with the DC motor and the ease of the distribution of the DC power have made trolley wire installations for haulage very popular. In shallow mines with very limited emissions of methane it did not constitute a major hazard but as mine depths increased and corresponding emissions of methane also increased fire and methane ignition hazards have become very serious. Conveyors have proved economic where intense mechanization of coal faces generates a large output of coal from a single face, but the fire and respirable dust hazard associated with them are no less serious. Recognizing these shortcomings, the Federal Coal Mine Health and Safety Act of 1969 laid down numerous provisions for the safe use of trolley-wire haulage and conveyors (2) which generally improve safety but in some cases complicate mining operations and have decreased productivity significantly since 1969. In course of time as coal mines become deeper and hence gassier and as the emphasis on safety increases it would be inconceivable to use trolley-wire haulage under ground as already witnessed in several other countries with deep coal mines. With rising capital investments and cost of the protection against fire and respirable dust, the use of conveyors may also have to be limited to special areas, e.g. main entries. Indeed, there are only two alternatives available, namely; (1) Degasify the coal seams prior to mining and use conventional electrical power, or (2) Develop alternate sources of power which would be safer and yet efficient and cheap.

Jan 1, 1975

By Vincent Tricot, Daniel Altier, Roger Storry

"INTRODUCTION The Liantang / Heung Yuen Wai Boundary Control Point (BCP) project, located in the north-east New Territories of Hong Kong, will form the seventh land crossing between the Hong Kong Special Administrative Region (HK) and Shenzhen in China (Figure 1). The BCP project comprises an 11km long dual two-lane trunk road linking the border crossing facility to the existing road infrastructure in HK and when completed it will facilitate future regional development and alleviate frequent traffic congestion at the existing Boarder control points.In December 2013 Dragages Hong Kong (a member of the Bouygues Construction Group) was awarded the 5.4km long Contract 2 section of the project, including the 4.8km long Lung Shan Tunnels, by the Civil Engineering and Development Department of the Government of the HK SAR. To overcome the difficult ground conditions anticipated along the Contract 2 section of the project the tunnels will be constructed using mechanical and drill and blast (D&B) excavation techniques together with a 14.1m diameter multi-mode Earth Pressure Balance Tunnel Boring Machine (TBM). Land constraints imposed on the project alignment require that the final 500m section at the northern end of the Lung Shan tunnels, under Princess Hill (Figure 2), takes an almost 90 degree turn towards the north. The resulting 354m radius curve restricts the sight-line of road users to below the minimum 110m at 80km/hr hence, the internal span of the tunnels needs to be increased from 12.6m, in the standard straight section, to 15.4m in this curved section to accommodate a widened shoulder which will provide the required sight-line distance."

Jan 1, 2016

By M. S. Celik

Adsorption of sodium dodecylsulfonate (SDS) and dodecylaminium hydrochloride (DAH) on Buller seam coal, New Zealand, have been studied. Both surfactants adsorb effectively on the coal below pH 8, and the adsorption isotherms established at pH 4 are essentially the same at lower concentrations. These findings suggest that the adsorption of these two ionic surfactants on coal is controlled by a hydrophobic bonding mechanism. However, the results of calorimetric studies suggest that coulombic attraction also plays a part in the adsorption mechanisms. It has also been found that both the SDS and DAH adsorbed in the first monolayer are not removed by lowering the surfactant concentrations in the bulk solution.

Jan 1, 1993

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study is to compare amino acids and organic acids in the extraction of gold from silicate ore. Amino acids were found to have higher efficiency of gold extraction than organic acids at the same acid concentration, which is likely due to amino acids having both carboxylic and amine groups in their structure, while organic acids only have carboxylic groups. Five amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and seven organic acids (citric, malic, tataric, fumaric, oxalic, succinic and ascorbic acids) were selected to investigate gold extraction efficiency. Aspartic acid was found to have greater capacity to extract gold than succinic acid. The optimal gold to aspartic acid molar ratio was 1:6, and low concentrations of aspartic acid extracted 35 to 42 percent of gold from silicate ore within 15 days. Further studies are needed to increase gold leaching and reduce incubation time. The results imply that aspartic acid can be used as an alternative reagent to traditional methods for extracting gold from ore. This method is nontoxic to humans, is environmentally friendly and can have real applications.

By William Bergeson

"BACKGROUND As of December 2015, there are roughly 475 road tunnels within the United States according to the most recent national tunnel inventory data compiled by the Federal Highway Administration (FHWA); whereas, there are more than 615,000 highway bridges on public roads. The FHWA estimates that tunnels represent nearly 100 miles of Interstates, State routes, and local routes. Tunnels are part of the national transportation infrastructure and represent a significant financial investment for the owner and, hence, the tax payers. Tunnels, that are not properly maintained, usually require more extensive repairs and consume more resources. Tunnels must provide safe, reliable, and effective transportation even as these structures age and deteriorate. Furthermore, tunnels generally remain in service for extended periods of time due to their very high construction costs. For example, many tunnels were constructed decades ago during two historic periods of highway system expansion; the first period correlated with the era of public works programs linked to the Great Depression of the 1930-40s; and the second period of expansion occurred with the building of the interstate highway system in the 1950-60s. As such, these tunnels are fast approaching 60 to 80 years old. Congress enacted the Moving Ahead for Progress in the 21st Century Act (MAP-21), which was signed by the President on July 6, 2012. This legislation followed a fatal tunnel incident on July 10, 2006 and a National Transportation Safety Board (NTSB) report1 that noted the importance of conducting regular tunnel inspections. MAP-21 authorized the Federal Highway Administration (FHWA) to develop a mandatory inspection program for all tunnels on all public roadways (Bergeson and Ernst 2015): To help safeguard tunnel users and to ensure reliable levels of service, the FHWA developed the National Tunnel Inspection Program (NTIP), which is comprised of the National Tunnel Inspection Standards (NTIS), the Tunnel Operations Maintenance Inspection and Evaluation (TOMIE) Manual, the Specifications for National Tunnel Inventory (SNTI), and the Manual for Bridge Evaluation (MBE). The data collected from the program will be stored in a National Tunnel Inventory (NTI) database. A comprehensive and refresher training program was also developed to help qualify and certify key tunnel inspection personnel to include the program manager and team leader."

Jan 1, 2016

By Jameel Menashi

Aqueous solutions of Na2Cr04 can be reduced with CO to produce hydrous Cr203 and NaHCO3/Na2CO3. CH3OH, HCOO and HCHO in the presence of CO2 also reduce Cr 6+ and yield similar products. It is shown that the rate of Cr6+ reduction can be represented by the expression -d[Cr6+]/dt=k[Cr6+)1/2[R] where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mole. Rapid reduction rates are attained at temperatures in excess of 220°C and, with these three reductants, a green acid-insoluble readily filterable hydrous Cr203 is formed. With HCHO significant reduction of Cr6+ occurs at about 80-100°C and an acid-soluble violet modification of hydrous Cr2O3 is formed. The reduction process is reasonably selective: solutions of Na2CrO4 contaminated with Mo6+ and W6+ can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels. These findings are utilized as a basis for a process for recovering chromium from secondary source materials.

Jan 1, 1984

By Shu Fan Chau, Innes Duncan, Harry Asche, Bill Newns

The North Auckland Line (NAL) in Northland, New Zealand, is being upgraded to pass Hi-Cube containers. The line includes many tunnels and bridges which need to be refurbished to improve structural clearances and line capacity. Tunnel 2 along the line, the Makarau Tunnel, has posed special challenges. Opened in 1898, the tunnel suffered multiple collapses during construction and has shown significant distortion during operation. The tunnel has been repaired many times since opening. Successfully enlarging this delicate and distressed structure has involved historical research, advanced analysis and design, and careful construction. The results provide lessons for dealing with brick lined tunnels and poor ground conditions

Jun 13, 2021

By Michael D. Loy

This paper examines the computerization steps of United Coal Company of Bristol, Virginia. OVERVIEW Producing close to 7,000,000 tons per year, United Coal Company is one of the most interesting mining companies in the east. Their approach to mining reflects a dedication to modern technologies and extraction methodologies. With varying amounts of production coming from four divisions (a fair amount of production comes from contract operators) and over a billion tons in recoverable reserves, United rests heavily on the planning and engineering efforts of a centralized engineering group. Although each division relies on its own engineering personnel for day-to-day management and operations, long range planning and reserve management is conducted at the corporate engineering level. This group, while extremely competent and efficient, is relatively small (7 people), when compared to the needs of a large mining company.

Jan 1, 1985

By Harry Perry

U. S. consumption of sulfur and sulfur products is expected to increase at a rate of 8 percent per year between now and 1980, largely as a result of their use in fertilizer markets. World consumption is also increasing rapidly, but at a-lower rate, about 6-percent per year. In 1965, sulfur recovered in the United States from purification of natural gas; nearly doubled from the 1956-1960 average; production from pyrites declined; and production of elemental sulfur increased 15 percent. Concern about air pollution resulting from sulfur oxides produced from the combustion of fossil fuel has lead to intensive research on methods of removal before combustion, during combustion (in-process methods), and from the resulting flue gases. If all the sulfur in fossill fuels were recovered, more sulfur products would be produced than were consumed in the United States in 1965. Removal of sulfur from coal before combustion could result in a product sufficiently-high in sulfur to be a suitable raw material for sulfuric acid manufacture. In-process methods produce solid sulfates, some of which may have commercial value. Flue gas removal' methods for sulfur oxidest generally result in the production of a byproduct either of sulfuric acid or sulfur. The projected sale of these materials significantly lowers the anticipated cost of sulfur dioxides pollution abatement. Alternate methods for sulfur dioxide reduction are discussed. The various proposed processes are described and costs are given for the various methods for which estimates have been made.

Jan 1, 1967

By Sean Dessureault

The mining industry has used fleet management systems (FMSs) for decades. These systems were developed long ago in large truck-and-shovel mines, where hardware sales were the core business driver for vendors. These traditional models can be overhauled in the era of the Internet of Things (IoT), Big Data, gamification and low-cost tablet technology. Relatively low-cost tablets are ubiquitous in modern life, and they are packed with communication radios and sensors like Global Positioning System (GPS) and inertial measurement units used widely for games, fitness measures and navigation. These powerful computer devices provide the same, if not more, sensing capability than traditional fleet management hardware, all at a fraction of the cost and without complicated cables or challenging supply lines.