Search Documents

By G. K. Hoffman

Humate, defined as weathered coal or mud-stone rich in humic acid (HA) and fulvic acid (FA) have been mined, primarily as soil amendments or drilling mud additives, in New Mexico for 15-20 years. The New Mexico humate resource is estimated to be 11 Gt, including weathered coal and organic mudstone. The HA and FA content determines the end-use, therefore a simple and consistent method of measuring organic-acid content was developed. The New Mexico Bureau of Mines and Mineral Resources method is based on repeated alkali leaching and acid precipitation. Precipitates of humate are ashed, with mass balance of solids maintained, to correct for material added during alkali-acid treatment. Analyses of upper coal member, Cleary Coal Member (Menefee Formation) and Fruitland Formation samples from the southeast San Juan Basin show ashing to be important in accurate analysis of FA content. Ash in the total FA fraction averages 70% compared to 2% in HA. The FA in weathered coal and organic mudstone are similar, although HA is significantly higher in the former. As weathering progresses, the FA content of weathered coal increases faster than in organic mudstone because of the greater total organic material in coal.

Jan 1, 1994

By Jeff Mattern

"Slope performance monitoring, dependable operational practices and ongoing collection of geologic data in openpit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike openpit has been ongoing since the early 1980s, having its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls.While technology can be efficient, interesting for collecting needed data, slope design fundamentals based on that data can be applied to create much added value.With the proper available equipment, steepening of bench face angles via presplit blasting is not an uncommon method for steepening of interramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted, resulting in quantified, rock-specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2° on a 305- m (1,000-ft) high slope, without the necessary purchases and procedural changes that would be required for presplit drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves.LocationThe Goldstrike openpit is located in the Great Basin, on the northern end of the Carlin Trend gold belt in northeastern Nevada (Fig. 1). The mine has produced more than 1.2 kt (43 million oz) of gold during the past 30 years."

Dec 1, 2018

By S. L. Barua

An industrial engineering and computer simulation study was conducted on reclamation operations to evaluate the possibility of integrating mining and reclamation operations, and to evaluate the factors which influence the production potential of scrapers. The study was done in a southern Illinois strip coal mine producing approximately 2.27 M metric tons (2.5 million short tons) of clean coal annually. The main outcomes of this study are (a) it is possible to reduce reclamation cost about 20-25 percent by integrating reclamation and mining operations, (b) haul distance has the most significant effect on scraper production, (c) push-pull is the best mode of operation for wheel scrapers for topsoil/subsoil removal, and (d) historical data obtained from the mine for one year show that average dozer productivity in rock grading is about 60 percent lower than the expected production; similar data for scraper is about 25 percent less.

Jan 1, 1981

By Walter E. Dean

Deep-sea manganese nodules are considered to be potential ores of manganese, nickel, cobalt, and copper. Considerable time, effort, and funds have been applied to the study of Se distribution of nodules on the sea floor and the location of economically important areas, but little effort has been spent in understanding the origin of nodules. Most theories that have been proposed to explain the origin of manganese nodules have been based on inorganic physicochemical processes. It is not by coincidence, however, that the area considered to be most economically feasible is in the zone of high biological productivity in the eastern equatorial Pacific Ocean and underlain by siliceous biogenic sediment. The genesis of manganese nodules and the concentration of many trace elements are intimately associated with biological processes.

Jan 1, 1982

By R. Addison

This is the story of the Carlton Mill. But first-a little geography. For those who do not know where the Carlton Mill is, or, perhaps, have only a vague idea, its location is indicated in Figure 1. The plant is situated on the road between the two old mining towns of Cripple Creek and Victor, 10 the west of Colorado Springs. From Denver, it's about 110 miles by road. The story of the Carlton Mill began with the discovery of gold at Cripple Creek in 1890. This discovery set off a major boom such that, by the turn of the century, there were 450 separate operating mines in the district. Gold production boomed early and declined rather rapidly as indicated by the graph in Figure 2. Significant factors affecting production are shown on the graph-the raising of the gold price in 1934 from $20.67 to $35.00 per ounce and the government executive order L-208 in 1942 requiring the closure of all gold mines.

Jan 1, 1983

By J. C. Nigro

The potential use of prereduced pellets in the burden of the blast furnace continues to be a topic of interest. Several excellent papers have been written describing the theoretical and experimental rewards. (1) (2) (3) (4) (5) (6) (7) (8) (9) Significant increases in iron output and substantial savings in coke consumption are major advantages over conventional iron oxide pellets. The savings are especially important in areas where good coking coal is at a premium. Lower handling and transportation costs may also be factors favoring prereduction. When considering the overall cost of making and smelting prereduced materials the optimum metallization level becomes significant. An analysis by Agarwal and Pratt of the thermodynamic aspects of blast furnace operation with all prereduced pellets shows that the criteria controlling coke consumption depends upon the degree of reduction and upon the percentage of oxygen (present as FeO) removed by solution loss.(8) The authors state that although the chances of obtaining large fuel savings are greatly improved when metallization is high, reduction to the highest degree, which is costly, may not result in the lowest energy requirement per ton of hot metal; thus, over reduction could possibly result in wasted energy in the blast furnace.

Jan 1, 1968

By Jeff Reid, Mohamed Maghari, Nicholas Joens

The Burnaby Mountain Tunnel was an integral part of the Trans Mountain Expansion Project. General Contractor, Kiewit Ledcor TMEP Partnership (KLTP), contracted with McNally Construction to build an underground tunnel between the Burnaby and Westridge Marine terminals under Burnaby Mountain. The pipeline was constructed within a 2.6-kilometre tunnel, eliminating the need to run the pipeline over the mountain and minimizing community impacts. The complexities of this Project led to multiple innovations, including the design of a Tunnel Boring Machine (TBM) capable of excavating through mixed-faced conditions concurrently thus allowing the Project team to complete the tunnel with limited geotechnical information.

Jun 23, 2024

By L. D. Patts, S. J. Janisko, E. G. Cauda, A. D. Bugarski, G. H. Schnakenberg, J. A. Hummer

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on the performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for DFEs when the engine was operated at high-load modes rather than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on the total concentration of nitrogen oxides (NOX) were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes..

Jan 1, 2011

By John W. Crawford

The title of the paper which I have been asked to present is somewhat misleading it infers in fact that there is a definite coalbed height below which raps or canopies cannot be applied to electric face equipment. Although this may be so with regard to certain pieces of existing equipment under certain conditions, to date we do not have enough experience to determine this magic number. Therefore MESA is continuing to hold the line on the time frames stipulated in Section 75.1710-1 of the Mandatory Safety Standards - Underground Coal Mines, which at this point in time requires these protective structures in mining heights of 60 inches or more. In order to give you an idea why we are taking such a firm stand on this matter, I believe it is necessary to describe some of the background work that was done prior to promulgation of the regulations and to give a resume of our experience since the requirements have become effective. Initially MESA made field investigations of all underground mines to determine what the state of the art was in the use of cabs and canopies for protecting equip¬ment operators from falls of roof. These studies revealed that the application was basically in its infancy and what progress had been made was due to the impetus of the mine operators themselves. Manufacturers of electric face equip¬ment provided these structures only on the direct order from the mining company and built them to their specifications. In talking to the operators and the miners in mines where cabs or canopies were in use, it was the consensus that these structures did improve safety and that although originally there was some reluctance on the part; of the miners to work in the confines of a cab or canopy, mast would not work without them once they had been adapted to the equipment.

Jan 1, 1975

By O. M. S. Rodrigues

The kaolinite presence in bauxite ores increases caustic soda consumption during the digestion step in the Bayer process. Depending on the kaolinite content, the utilization of the ore in the Bayer process may be unfeasible. This investigation addressed the variables involved in kaolinite flotation through microflotation experiments in a Hallimond tube and zeta potential determinations. The tests were performed with a pure sample of kaolinite (96%). Five collectors were tested: Duomeen T (DT), cetyl pyridinium chloride (CPC), cetyltrimethylammonium bromide (CTAB), dodecylamine (DDA) and Flotigam EDA (EDA). Four of them performed well as collectors, at a concentration of 1x10-4 mol/L: CPC, CTAB, DDA and EDA. The kaolinite isoelectric point (IEP) was determined at pH = 4.6. The IEP was shifted towards higher pH values in the collectors? presence, indicating specific adsorption onto the mineral surface.

Jan 1, 2011

By Peter Schmäh, Tobias Engel

The E-Power Pipe technology was originally developed for the trenchless installation of protective pipes and pipelines of 10" to 28" diameter, over long distances of more than 4,000 ft. The twostage process combines elements from Horizontal Directional Drilling (HDD) and microtunnelling technology. A microtunnelling boring machine (MTBM) excavates the borehole using a specially designed, temporary jacking pipe. A Rack & Pinion jacking frame pushes the equipment during the pilot bore and pulls in the prefabricated pipe string in a second step. The slurry microtunnelling machine is equipped with a jet pump, creating the so-called AVNS machine type. A new generation of small hard rock cutting wheels complements this considerable achievement for the tunnelling industry

Dec 1, 2022

By Michael P. Evans

Traditionally in coal processing jigs have been used to clean the coarse coal fraction, the +3/8" or +1/4" material. Today with the advent of modern fine coal jigs in the United States, its place was moved from the coarse to the inter- mediate coal circuit, the 3/8" x 100 mesh. The most economical coarse coal circuit to build and operate is a heavy media bath circuit. The following table summarizes the cost per raw coal ton processed for a coarse coal jig circuit, and a coarse coal heavy media bath circuit. The flowsheets used to compare these two circuits are shown in Figures 1 and 2.

Jan 1, 1983

By W. Fletcher

Startup of a new plant is a very interesting time. It generally is also a very demanding and often frustrating period. Startup problems can become serious ii they impede the early achievement of full plant production. Raw materials are wasted, manpower is unproductive, field modifications can be extremely expensive and market commitments may not be met. This paper outlines a well proven and highly successful approach to eliminating many of the problems and frustrations often experienced in plant startup. The procedures and methods summarized in the following paragraphs have been developed over a period of 25 years during which some 90 plants were started up.

Jan 1, 1981

By Paul H. Johnson

The CH Leaching process is a new, more sophisticated, form of gold, silver, uranium and sulfide copper heap leaching wherein each layer of a multi-layered heap is divided into a number of independent cells, each of which are successively formed and leached in the top layer of the heap to their maximum economic recoveries, and then rinsed and sealed from further leaching. Triangular earth berms form the outside walls of the heap and a gridwork of rock-filled berms on top of the bottom pad form independent under- heap solution storage zones. The high degree of solution recirculation and staging that occurs in this process produces a relatively small volume of very rich pregnant solution. The cellular heap design and its mode of operation result in a uniform, intensive, long-term leach for all of the ore particles in the heap. Besides improved metal recoveries, the process appears to have several cost and operating advantages. In the CR2MR process, sulfuric acid and a soluble sulfide are added to a gold and/or silver pregnant leach liquor to precipitate most of the contained silver, mercury, copper, etc. as sulfides at a pH below 2.5. The other product of the reaction is solubilized HCN. Following a liquid-solid separation step, cyanide is regenerated in the supernatant solution by raising the pH to a level above 9.0. This process regenerates a portion of the cyanide used in the leaching step, removes contaminant ion species (silver, copper, mercury, etc.) from the leach solution and, in a subsequent step, recovers the gold in an enriched form. It is believed that substantial cost savings may be experienced by the use of this process in some gold and/or silver leach systems.

Jan 1, 1984

By C. H. Rawlins

The total amount of ferrous slag generated in the U.S. is about one-third the amount of iron ore mined, thus ferrous slag can be considered a significant mineral body for processing. Steelmaking slag contains up to 30 wt.% metal of which only the >25mm fraction is commonly recovered. A grinding study was conducted of BOF, EAF, and LMF slags using the Bond Work Index method to determine grindability to 106µm. Work Index values obtained were 13.8-24.9 kWh/ST, depending upon the slag type and composition. Steel particles were magnetically recovered from the crushed and ground samples for size-by-size analysis, yielding up to 18 wt.% of the slag weight recovered as magnetic. The recovered material, as characterized by inert gas melting, was found to be 61-96 wt.% metallic.

Jan 1, 2008

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

8.1 INTRODUCTION Under room and pillar mining if the extraction ratio is low, (i.e., < 50%) a pillar can support the overburden without collapse and there will be no surface subsidence whatsoever. In other words, if the pillar sizes are properly determined to support the overburden weight, the roof strata cannot cave and there will be no surface subsidence, provided the entry width is small and properly reinforced so that a continuous roof fall leading to piping or the total collapse of the roof does not occur. Under the prevailing mining conditions in the US if only development mining is em¬ployed in room and pillar mining (i.e., no pillar extraction), the extraction ratio is usually less than 50% and generally no surface subsidence will occur. If pillar mining is employed, surface subsidence may occur, depending on the extraction ratio and the size of the remnant pillars (or stumps) left in the gob. The higher the extraction ratio, the smaller the stump pillars left behind in the gob. As the size of the stump pillars becomes smaller, the possibility of their support¬ing the roof without collapse is smaller. If all stumps are crushed completely, the roof will collapse and surface subsidence will occur. Again, whether surface subsidence occurs, it depends on whether the remaining stumps can support the overburden or not. Therefore, since the weight of the overburden which the stump pillars have to support is proportional to the mining depth, a fixed¬size stump pillar can support the overburden at a shallow depth, but will collapse under greater depths. In this context extraction ratio is not the only parameter for determining whether surface subsidence will occur. Furthermore, during pillar mining a pillar can be cut away in many ways to finally reach the same extraction ratio. Therefore, the safest way to determine whether or not sur¬face subsidence will occur in room and pillar mining is to compare the strength of all stump pillars in the panel of interest with the weight of the overburden that the pillars have to support. If they are too small to support the overburden, surface subsidence will occur. Under normal mining practices the characteristics of surface subsidence profiles vary with methods of mining. In the US there are two types of coal mining methods, i.e., longwall and room and pillar mining. Longwall mining is indisputably a total extraction method, but different percentages of coal recovery are achieved in room and pillar mining. Recovery is much higher for sections with pillar extraction than those without pillar extraction. For those without pillar extraction, coal recovery increases with increasing entry width or decreasing pillar size. For those with pillar extrac¬tion, the total coal recovery depends on the amount of coal ex¬tracted from each pillar which is in turn dependent on the roof conditions and methods of pillar extraction. Bauer and Hunt (1981) analyzed the characteristics of the subsidence profiles due to the three types of mining methods in Illinois. Fig. 8.1 shows the range of locations associated with the following profile features: profile edge, maximum tensile curvature, maximum slope, maxi¬mum compressive curvature, and maximum subsidence. The scat¬ter of the data increases with decreasing percentages of extraction. The profile is much sharper for longwall mining and becomes milder as percentage of extraction decreases; for longwall mining the profile edge is always beyond the opening, while in room and pillar mining it may fall within. The location of maximum tensile strain moves outward, while that of the maximum compressive strain moves inward as the percentage of extraction decreases and the maximum subsidence decreases with decreasing extraction ra¬tio. The general concepts discussed in this chapter may not apply to the entry development sections between two longwall panels where roof caving in both panels are very severe and overlap each other. Consequently, it must be treated differently. 8.2 CASE STUDIES Kohli et al. (1982) described several case studies on surface subsidence due to room and pillar mining with pillar extraction. In one case, the seam was 6 ft thick and ranged from 650 to 800 ft deep. The panel was 720 ft wide (Fig. 8.2) and was developed with seven entries. Each entry was 18 ft wide and the pillars were driven at 88 ft center-to-center between entries and crosscuts. Dur¬ing retreating, two additional pillars (pillars J and K) were devel¬oped, two blocks ahead of the pillar line, to take the barrier pillar, 160 ft wide, between panel No. I and No. 2. Pillar extraction began by taking a central slice across the whole panel, beginning from pillar 0 through J. After that, each pillar was sliced by 6 wing-slices, 3 on each side, leaving 4 stumps, 2 on each side. One of each pair was triangular shaped approximately 6 ft wide by 26 ft long. The other was trapezoidal, 26 ft long by 16 ft and 10 ft wide at the upper and lower bases, respectively. This resulted in a total extraction ratio of 85% within the panel. Obviously the stump pillars were not large enough to support the overburden and col¬lapsed completely. The final subsidence profiles were rather smooth, just like those under total extraction (Fig. 8.3). The max¬imum subsidence on Lines A and B was about 3 ft for an average mining height of 6 ft, but the locations of the maximum subsidence were skewed toward panel No. 1. Along Line D, the central por¬tion was flat-bottomed, but the maximum subsidence was only 2 ft, mainly because Line D was only two blocks from the right-side edge. Notice in every profile there was heaving of as much as 0.3 ft, beyond the edges above the solid coal. In another case (Fig. 8.4), the seam was 6 ft thick under 650 to 850 ft cover. Three panels, 710, 400, and 350 ft wide, respec¬tively, were extracted side by side. The entries were 18 ft wide and the pillars at 88 ft center-to-center between entries and crosscuts. Pillar extraction was practiced the same way as described previ¬ously. According to the mine maps, there was no barrier pillar left between the adjacent panels. Thus after extraction the three panels formed a common gob of more than 1460 ft wide. This was re¬flected in the development of the subsidence profile along the county road. After Panel No. I was mined, the maximum subsi¬dence of 1.2 ft occurred at Monument No. 1. This was increased to 1.6 ft after the extraction of Panel No. 2 and went to a further 1.8 ft after the extraction of Panel No. 3. The final maximum subsidence of 4.3 ft occurred at Monuments No. 6 through No. 8, while the remaining portion of the county road showed rebound. However it must be noted that the subsidence profiles were rather bumpy and fluctuated, perhaps an indication of the irregular stump pillars that were left and crushed at various time after mining. Moebs (1982) surveyed the subsidence profiles of four room

Jan 1, 1992

By J. A. Lepinski

The FASTMETSM Process is a coal-based process for converting iron oxide fines into metallic iron. The end product, direct reduced iron (DRI) is used as a low residual charge material in electric arc furnace steelmaking. This paper describes the FASTMET Process and its potential application in the United States. Operating results from a 175 kg/h process simulator are presented. Characteristics of the end product are discussed. Process economics are reviewed along with plans for scaling-up the process to full commercial size.

Jan 1, 1993

By John D. Smith

This paper describes how a knowledge of inherent rock characteristics can aid the mining engineer in his design of a mining method for a massive domelike structure. The paper shows how the pertinent rock characteristics were measured and analyzed and how the data obtained was used for design purposes. This analysis was conducted in 1964 in a producing salt dome, since that time, mine management has tried certain of the recommendations for mine design changes. The results of such changes are presented.

Jan 1, 1968

By Carlo Sampaio, Moacir Veras, Aaron Young, Carlo Petter

"Three major challenges for the mining industry are the minimization of energy use, water consumption and environmental impact. Therefore, any technique that reduces milling waste, decreases water usage and shrinks impact during mine life must be considered a major innovation in mining.To these ends, one of the most impactful developments in mining within the last 10 years has been the expanded use of high technology sensors to create preconcentrations of mine ore (Jönsson, 2014). The most common sensors used are charge-coupled device (CCD) cameras, that allow through a red, green and blue (RGB) coloring system, the separation of minerals with different colors, tones and, in many cases, with differences in brightness.More recently, the development and use of dual energy X-ray transmission (DE-XRT) to enable the separation by atomic density of the constituent minerals within a given rock has become a reality. Within this work, a rapid bibliographical review of the CCD and DE-XRT methods and examples of their usage within mining and the industrial minerals sector are presented.Sensor-based sorting in miningAutomation within mining is one of the industry’s current goals. Sensors of various kinds have been used as steps toward automation in recent years, from improving the safety and productivity of haul trucks through the use of cameras and global positioning satellites (GPS), to the divination of slope failures. Just as with other mining areas, sorting has improved dramatically and made great steps toward automation in recent years (Wotruba et al., 2014).Sensor-based sorting (SBS) uses spectromatic sensors to identify intrinsic characteristics of particles and separates them by either mechanical or pneumatic means into different product streams (Wotruba et al., 2014). SBS can be used with great effectiveness to improve gravimetric beneficiation through the selective separation or preconcentration of run of mine ores (ROM)."

Jan 1, 2015