Search Documents

By T. Patten

Inter-Mountain Labs, IML, performed a study comparing mining waste rock sample analysis by Net Carbonate Value (NCV) and Modified Sobek acid-base accounting procedures. The study looked at 468 waste rock samples and compared the data for Neutralization Potential (NP), Acid Generation Potential (AGP), Net Neutralization Potential (NNP), and the ratio of NP/AGP. The study found that a majority of the samples were below 50 Tons CaCO3/kTons. This subset of ?low-level? samples was also examined separately for Acid Base Accounting parameters. The analysis compared the NCV procedures to the Modified Sobek procedures and concludes that the NCV procedures are as protective of the environment as Modified Sobek procedures.

Feb 27, 2013

By Todd Wanless

This paper addresses the challenges experienced by the designer and three government agencies during implementation of major improvements for the Turkey Creek Tunnel in Kansas City, Kansas. The tunnel serves as a vital stormwater conveyance system for upstream flood control. Major structural deficiencies were identified within the tunnel including complete loss of sidewall and invert. Without immediate attention, complete loss of the tunnel arch could lead to blockage and extensive remedial repairs under difficult conditions. Considering that tunnel flows must be maintained during construction, a phased design and construction process has been implemented to expedite stabilization of the erosion cavities followed by tunnel liner repairs.

Jan 1, 2008

By Ray Brainard

The subsurface investigation for the Reach 4 Tunnel was expected to be completed in a single phase. This assumed that data from two nearby previous tunnels, combined with limited new subsurface information and surface mapping would be sufficient to characterize the rock behavior. Unforeseen rock conditions and complex faulting led to the recommendation for a second phase. This decision was not reached easily, as much of the follow-on work required helicopter support, and associated costs. The second phase of drilling found significantly more variability than the first phase and led to a very different and better understanding of the geologic and geotechnical conditions, and rock characterization.

By J. Winterton

Cripple Creek and Victor Gold Mining Co. is developing a full-scale pad injection program as part of the overall operational plan for the Valley Leach Facility. As part of the development process the mechanics of the injection methodology are evaluated in the context of physical injection measurements, outcome from geophysical monitoring, and gold leaching theory. The results indicate that hydraulic fracturing analogies advanced heretofore do not accurately describe injection phenomena in unconsolidated and noncohesive material typical of leach pads. A new interpretation is presented and extended to define operational strategies for maximizing gold production.

Feb 27, 2013

By G. Tiravanti

A recurrent concern in mining operations is how to deal with the large volumes of fresh water used which in turn generates large volumes of effluents that have to be treated. Water treatment can focus in one of two main strategies: treat the effluent as it is produced, or use a simulation tool to optimize water use in the process and reduce volume of effluents, contaminants concentrations, operational costs, and so on. This article shows a successful tool developed in Matlab-Simulink® that allows modelling a mining process and simulating potential improvements to evaluate the results. This tool has been proven in Cu-Mo operations and recently it has been used in poly-metallic operations. This article reviews the 4 Key Steps required to achieve our goals: a) Elaboration and verification of the mining Operation?s Block Diagram, based on a field survey; b)Model construction and input flows and qualities in selected streams; c)Model Validation and Simulation of new alternatives like recirculation, changes in reagents and dosage, partial treatment, flows merges/separation, and others; d)Development of the Optimal Solution which consists on determining the CAPEX and OPEX.

Feb 27, 2013

By Samuel J. Gambino

Preliminary recommendations for the Upper Northwest Interceptor 1&2 specified installation of reinforced concrete pipe using pipe-jacking methods. However, a larger one-pass tunnel constructed using precast segmental lining would provide additional storage volume. The risk of encountering unexpected conditions or events and the resulting cost impacts could differ significantly for these two options. A probabilistic life-cycle cost analysis of these alternatives was performed. This paper discusses the construction alternatives considered, the risk assessment methodology used to evaluate these alternatives, the input parameters and risk factors used in this analysis, and the recommended project which is currently being constructed.

Jan 1, 2008

There is wide agreement that sustainability has multiple dimensions, but substantially less agreement on the appropriate balance among those dimensions. This occurs because peoples’ vision of a sustainable future, their goals for sustainable development, and their objectives for resource management are reflections of their values, culture, and life experiences. Even assuming agreement about the objectives of sustainable resource management can be reached; there is still a need for policy and decision makers to choose from among alternative courses of action, each of which has its own set of impacts and outcomes. One of several tools used to compare the consequences of alternative actions is the Computable General Equilibrium (CGE) model. This paper uses CGE modeling to demonstrate how policy decisions do not take place in a vacuum and how policy-makers must be aware that there are trade-offs involved in any decision.

Jan 1, 2005

By L. R. Moore

Arsenic is among the list of major contaminants in mining aqueous waste streams. Though the elemental form is toxic, the aqueous oxyanions are more so. The most common forms of arsenic released during mining processes are arsenate and arsenite. The common treatment technologies to date can be summed up in these major categories: oxidation, coagulation, absorption, and media filtration. These methods can often involve many expensive processing steps that may also be limited by variables, such as total dissolved solids, other cations and anions, and the oxidation state of the arsenic. An innovative technology, falling in the absorption category, was developed that can successfully reduce such aqueous forms to a level below the EPA recommendations. This new technology offers a unique and viable solution which is transparent to the above mentioned limitations.

Jan 1, 2012

By A. Nieto

A dump edge and vehicle proximity warning system is being developed at the Colorado School of Mines using GPS and wireless local area networks to improve the safety of off-highway trucks in open pit mines. After two years of research, software development, and testing in the laboratory, field tests are currently being carried out at operating limestone quarries and open pit mining operations to evaluate the effectiveness of the system under rugged operating conditions. This paper describes the progress made on this NIOSH-funded project and discuss, tests carried out recently, at the Morenci open pit copper mine in Arizona.

Jan 1, 2002

By Alex Naudts

Pre-excavation grouting is a predictable and reliable technique performed to prevent or minimize settlement in advance of, or during the tunneling operation. It safeguards the infrastructure above the tunnel alignment. Cement based suspension grouts and sodium silicate based grouts are frequently injected to consolidate and strengthen the formation and create a reinforced canopy above the tunnel trajectory. Grouting is typically performed through permeation and permeation in conjunction with hydrofracturing. Multiple injection passes through steel sleeve pipes are ideal, since they create an effective forespiling system to facilitate tunneling without causing unacceptable settlement, even with minimal overburden thickness. Ten pre-excavation grouting projects performed in the North America are discussed in this paper.

Jan 1, 2008

By C. James, J. Siefke, D. Shumway

The Mojave Desert is a particularly fragile ecosystem that faces several significant impacts. These include rapid housing development, overdrafted water supplies, and loss of wildlife habitat as a result of mining, industrial activity and urban sprawl. Over the past three years, a diverse group of educators, natural resource managers and business leaders has been assembled under the auspices of a local college to provide unique natural resource education opportunities for the region. By leveraging the collective experience of these present generation natural resource professionals, the Mojave Sustainability Project hopes to provide the next generation of professionals with that knowledge and those technical skills upon which tomorrow’s community can rely. This paper is a case study of how partnerships between academia, government, industry and the community can serve to address the regional social, environmental, and economic needs of today, while investing in the development of those professionals who will balance these needs tomorrow.

Jan 1, 2005

By G. Luttrell, S. Keles, M. Eraydin, R. Yoon

The dewatering of fine particles is energy intensive and often requires costly capital expenditures. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids that enhance the performance of existing filtration equipment and an innovative hyperbaric centrifuge that utilizes both air pressure and centrifugal force for dewatering. The moistures obtained using these processes are 30-50% lower than those obtained using conventional methods. Another dewatering technology, known as the hydrophobic displacement process, can reduce product moistures to a level previously attainable only through the use of thermal dryers. This article presents test results obtained with these various advanced dewatering technologies along with estimates of the power consumption for each process.

Jan 1, 2007

By H. J. Haselhuhn

Selective flocculation and dispersion processes for the concentration of hematite ore are strongly dependent on the ionic content of the process water. It has been noticed that magnesium ions are more detrimental to iron recoveries during desliming and flotation processes than calcium. This phenomenon was studied by measuring the zeta potential of hematite ore at various concentrations of magnesium, calcium, strontium and barium at a pH of 11. Results show that zeta potential inverts from negative to positive at very low concentrations of magnesium ions in the solution. It takes a significantly higher concentration of calcium, ions to achieve the same effect. This difference may be attributed to the ability of magnesium ions to adsorb to all surface hydroxyl groups, whereas calcium, due to their larger size, can only adsorb to every other hydroxyl group. This hypothesis was confirmed by results similar to those seen with calcium when this test was repeated with strontium and barium ions. The tendency for calcium ions to adsorb to every other surface hydroxyl group causes higher concentrations of calcium to be less detrimental to hematite concentration processes than magnesium.

Feb 27, 2013

The inquiry into the explosion at the Moura No. 2 Mine in August 1994 recommended -?Emergency procedures should be exercised at each mine on a systematic basis, the minimum requirement being on an annual basis for each mine.? (Windridge et al. 1996). In December 1996 the ?Approved Standard for the Conduct of Emergency Procedures Exercises? was published and has been subsequently revised (Queensland Department of Mines and Energy Safety and Health Division 1999). This document provided guidelines for conducting mine site emergency exercises as well as the requirement for a test of state-wide emergency response by holding a Level 1 Mine Emergency Exercise at one mine on an annual basis. From 1998 to date (January 2008) ten Level 1 Mine Emergency Exercises have been held in Queensland, Australia. This paper discusses each of the exercises conducted to date as well as the logistics, scenario preparation, planning and organising required to conduct emergency exercises at this level.

Jan 1, 2009

By S. Addie

In the early 1990’s the British Columbia (Canada) mineral industry frequently discussed the need to participate in, and compromise with, public environmental interests in order to ascertain long-term stability. However, as the decade progressed the mineral industry withdrew from almost all meaningful public participation. As government protected areas policy in the past year has illuminated, there is a continued need for long-term land access stability. This paper historically analyses the public engagement policies of the British Columbian mineral industry while it participated in long-term consensus-based multi-stakeholder land-use planning processes. From this analysis the paper recommends that the mineral industry reengage the public and institute a new working relationship with environmental advocacy groups so as to ensure British Columbia becomes the most sustainable mineral producing jurisdiction in the world.

Jan 1, 2011

The ability to optimise a concentrator from mill feed to final products requires a simulator which integrates comminution, classification and separation modelling. In order to model this range of processes, such a simulator must handle a variety of information about the ore. The AMIRA P9 project has developed a whole-of-concentrator simulation capability which brings together a texture-based model of mineral liberation, quantitative X-ray micro-tomography analysis to measure the inputs required by this model, and a multi-component simulator software framework. In the context of this approach, the term ?multi-component? implies the ability of the simulation to handle many particle properties simultaneously; for example size, composition, density, floatability etc. The simulation software framework provides the means to manage the flow of data around a circuit flowsheet, allowing each process model to access the information relevant to that particular model. A case study based on plant data from a gold-bearing pyrite concentrator is used to demonstrate the capabilities of the multi-component approach in simulating circuits which contain comminution and separation processes.

Feb 27, 2013

Komatsu America has introduced its 2-MW (2,700-hp), 930E-3 ac electric drive truck with a 290-t(320-st) capacity. The truck is designed to provide increased productivity, lower cost per ton hauled and improved speed and control. The 930E-3 is powered by a Komatsu SSDA16Vl6016-cylinder engine. It is capable of speeds up to 65 km/h(40 mph) and is a 15-percent to 20-percent more productive unit than 218-t (240-st) trucks, at a lower operating cost per ton. The 930E-3 also provides enough torque and speed to get up and off ramps easier than mechanically driven trucks. And it can climb at altitudes up to 3,650 m(12,000 ft) without any fuel deration.

Jan 1, 2004

By M. M. Botz

There are currently more that 460 mines worldwide that utilize cyanide for gold and silver extraction. Despite this large number of cyanide-related mining operations, there have been no published accounts during the previous 25 years of the death of humans due to cyanide as a direct consequence of major mining-related environmental incidents. All published accounts of human deaths due to mining-related environmental incidents have been the result of physical inundation with tailings or waste rock materials. It appears that major mining-related environmental incidents have not been concentrated in any geographic location, are likely to occur regardless of the size of the mining company and do not occur more frequently with a specific type of mining activity. Several cyanide treatment and recovery technologies have been widely demonstrated to reliably control cyanide levels in mining solutions. With proper use of these technologies, tailings cyanide concentrations can be maintained at levels protective of wildlife while reducing the potential for adverse environmental incidents. The development of an international cyanide code of practice or management plan is recommended and should take into consideration the adoption of a weak-acid-dissociable (WAD) cyanide standard that maintains the levels entering a tailings impoundment below 50 mg/L.

Jan 1, 2001

By D. Hopkins, D. Türler, R. D. Giauque, W. B. Davis, M. Karaca

In a highly collaborative research and development project with mining and university partners, sensors and data-analysis tools are being developed for rock-mass characterization and real-time measurement of mineral content. Determining mineralogy prior to mucking in an open-pit mine is important for routing the material to the appropriate processing stream. A possible alternative to lab assay of dust and cuttings obtained from drill holes is continuous on-line sampling and real-time x-ray fluorescence (XRF) spectroscopy. Results presented demonstrate that statistical analyses combined with XRF data can be employed to identify minerals and, possibly, different rock types. The objective is to create a detailed three-dimensional mineralogical map in real time that would improve downstream process efficiency.

Jan 1, 2002

By C. K. Kocsis

A study was undertaken to evaluate the thermal environment and determine the contributing heat sources within the existing 153 Orebody of Coleman/McCreedy East Mine which would then enable the prediction of the climatic conditions in the mine?s future 170 Orebody. The study entailed continuously monitoring, for a 2-week period, the dry-bulb temperature, humidity and barometric pressure along the existing intake airways from surface down to the 4810 Level and throughout an active mining area on that level. Furthermore, the mining activities and associated equipment that could be responsible for any changes in the temperature and humidity conditions within this mining area were also monitored. These data were then used to develop and validate a climatic simulation of the mine?s mechanized cut and fill mining method. This climatic model was then transposed to the future 5700 Level in the deeper 170 Orebody, to determine the environmental conditions within its production workings and along the main haulage route ascending from that area. Based upon the simulations performed it was shown that the level of ventilation planned for the new orebody should be able to maintain adequate environmental conditions. However, this study did emphasize the importance of the appropriate distribution of airflow in workplaces that used auxiliary ventilation in order to sustain a suitable thermal environment.

Jan 1, 2009