Search Documents

By D van der Merwe

Tracers of known densities are used world wide in coal processing plants to evaluate plant performance. Tracers are added to the feed stream and are counted after being recovered from the product and discard streams to determine partition curves. The need to recover the tracers can be eliminated by adding radio frequency identification tags to the tracers. Readers mounted on the product and discard streams record the passing RF tracers and produce the partition curve instantly. Tests were performed with three different shaped tracers at different collieries on cyclones ranging from 510mm to 800mm in diameter. Sink and float analyses of coal samples were used to compare conventional partition curves to partition curves obtained by using RF tracers. The average amount of tracers recorded was 78% of tracers in the feed. The results indicate that the stone shaped tracers represent the results from the sink-float analyses the best. The results suggest that RF tracers can be used to evaluate cyclone circuits in the coal industry and will make it possible to evaluate a coal circuit?s efficiency without stopping a plant and waiting for laboratory analyses. Keywords Coal tracers, partition curve, radio frequency tracer, RFID

Jan 1, 2006

By K. M. Li, Y. D. Zhang

The selection of stripping dragline is a complicated problem. Several factors, such as the deposit buried conditions, the demand of mine production rate, cast blasting result, the mining/stripping operation method and parameters, etc. may comprehensively influence the optimal selection of technical specifications of the dragline. Under these circumstances, the basic thinking and procedures for dragline selection are put forward as follows. •Step 1—Initially estimate the dragline annual stripping rate and stripping bench height according to the annual coal production rate and advancing speed of mining front. Then the feasible alternatives of dragline sizes can be calculated and selected from the existing dragline series. •Step 2—A computer simulation model is developed to simulate the dragline stripping operation, to obtain a series of working face parameters, then to select the best dragline alternative. This step can be interactively iterated until the satisfactory results are obtained. •Step 3— Sensitivity analysis can be done with the systems simulation model by changing the stripping bench parameters, e.g. stripping bench height and cut width, etc. to verify and modify the selection results if necessary. The mathematical model for dragline stripping simulation has been set up. The flowchart of the model is shown. A case study for a large surface coal mine with annual production rate of 16 Mt/a is followed. The dragline bucket capacity and operation radius, stripping bench height and cut width as well as other parameters are comprehensively optimized and selected. Keywords: Open cast, dragline, specification, selection, cast blasting

Jan 1, 2003

By S. E. Olsen, M. Tangstad, G. Tranell, K. Berg, S. Gaal

In this study, the reduction behaviours of MnO and SiO2containing slags by solid carbonaceous materials was investigated in both small and larger-scale laboratory experiments. Five types of carbonaceous material were investigated: 2 graphites, industrial coke, anthracite and eucalyptus charcoal. The effects of the reductant type/properties on the reduction kinetics, metal composition and metal yield, have been quantified. Results show that the reduction rate is highly dependant on the type of carbon used. It was found that the reductant type significantly influenced the SiO2reduction while it did not seem to have a large effect on the MnO reduction. This may be due to the different CO2and SiO reactivities of the materials.

Jan 1, 2004

By R. J. Hundermark, S. Sun

The oxidation state dependence of the electrical conductivity of a calcium ferrite slag with 25 wt% CaO was measured at 1300°C using a shallow slag layer and two-electrode technique. The experiments were started in air and the slag was sequentially reduced by means of a controlled gas atmosphere using CO2and CO. The electrical conductivity in air was approximately 300 S/m and increased with reduction to approximately 1900 S/m at a pO2of 10-10atm. The interest in the oxidation state dependence of the conductivity of calcium ferrite slags was to provide a comparison with the conductivity of iron silicate slags and to establish the effect of slag basicity on the electrical conductivity and its oxidation state dependence. The results obtained are discussed in terms of the slag structural information available in the literature. The co-ordination of the ferric ions appears to play a large role in determining the electrical conductivity. Keywords: calcium ferrite, slags, electrical conductivity.

Jan 1, 2004

By M. M. Valenta

A number of challenges face platinum concentrator plant operators. These challenges include the increase in operating costs, the increase in smelter cost for the processing of concentrate, the shortage and cost of power, and the tightening of specifications on concentrate quality by the toll-smelting operations. Over the years the focus has moved from extracting the platinum group metals (PGM) from the Merensky Reef to the UG2 reef. This has a number of advantages, including the higher ?basket price? for UG2 concentrate, reduced mining cost per unit volume as a result of the higher density of UG2, and the reduction in overall concentrate tonnage to be smelted. In many cases the Merensky ore has been fully exploited and it makes sense for the focus to shift to the UG2 ore that can be accessed through the Merensky shaft infrastructure. The presence of relatively high levels of chromite in UG2 concentrate is, however, a major disadvantage due to the problems associated with smelting such a concentrate in conventional submerged arc furnaces. In addition to increasing the specification on the minimum PGM grade of concentrates, smelters have had to impose strict specifications on the levels of chromite in the concentrate. The threat of high penalties has forced concentrators to change their modus operandi, often resulting in a significant loss in recovery. The final concentrate grades and PGM recoveries are shown to vary significantly throughout the industry. The reasons for this include varying ore mineralogy and different operating philosophies. This would therefore imply that the opportunity exists to optimize the operations by considering fundamental aspects such as the PGM mineralogy and the application of appropriate technologies. By returning to the fundamentals of flotation and applying the findings of detailed process reviews, it has been possible to increase the concentrate PGM grade, reduce the concentrate chromite grade, and in some cases increase the recovery of PGM to concentrate. This paper presents case studies where this approach has been used to successfully optimize concentrator performance, resulting in lower operating cost and higher PGM production. Keywords Process optimization, platinum concentrator, milling, flotation, grade, recovery

Jan 1, 2011

By B. Unver

Effective strata control is a prerequisite for maintaining an efficient mining operation. If the strata in the vicinity of an opening are not controlled effectively, it is impossible to perform a safe, efficient and economical operation. In this paper, the reasons and outcome of instability problems observed in roadways opened in clay and marl at the Bolu Colliery of Yeni Çeltek Establishment are investigated. Roadways under examination were located in a syncline causing high residual tectonic stresses. Factors affecting the instability have been studied thoroughly by examining geology and tectonics of the area, establishing convergence measuring stations to understand in situ behaviour of supports and laboratory tests to determine engineering properties of samples taken from nearby convergence measurement stations. As a conclusion, a new production strategy and a new support system are recommended to maintain stability.

Jan 1, 1999

This publication is provided on an "as is" basis without warranties of any kind, either expressed or implied including, but not limited to warranties of title or implied warranties of merchantability of fitness for a particular purpose. The information contained in this publication is for general information purposes only. It does not constitute professional, technical, financial or other advice to the user of this publication and must not be relied upon as such by any person whatsoever. The use of this publication is at the users own risk. The authors/creators of the information contained in this publication have tried to ensure that the information contained herein is correct, but errors or inaccuracies may exist or the information may be incomplete, unreliable or no longer up to date. Therefore, no warranties of any nature whatsoever are given and any liability to any person in respect of anything and in respect of the consequences of anything done or omitted to be done, wholly or partly in reliance upon the whole or any part hereof, are disclaimed, including and without limitation any contractual, dialectal, direct, consequential or financial damages or losses. On no account will Organisers and/or any of the contributors or any person or entity involved in creating, producing or distributing the information and or software available in this publication be liable for any such damages arising out of the use of or inability to use this publication. Copyright Reserved The South African Institute of Mining and Metallurgy P O Box 61127, Marshalltown 2107, South Africa www.saimm.co.za All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without the written permission of the copyright owner. Although the greatest care has been taken in the compilation of the entire contents, the editors and publishers do not accept responsibility for errors or omissions. First Edition Copyright February 2004 Proceedings ISBN: 0-9584663-5-1 (1 volume and CD-ROM)

Jan 1, 2004

By H. Urata, K. Ishii

To determine the effect of F ions in the molten alkali silicate systems on their structures, quenched Na2O-SiO2-NaF systems were investigated by Raman spectroscopy and molecular dynamics simulation. The systematic increase of 1100 cm-1band intensity in the Raman spectra of the silicate melts accompanying the replacement of F for O provides the evidence for concomitant polymerization of melts. From the molecular dynamics simulation, it was confirmed that most of substituted F was mainly coordinated to Na+ ions but not Si4+ions. These results were consistent with the mechanism in which F associated with otherwise network-modifying Na rather than with network-forming Si. Since F was associated to Na+ ions, the replace of O ion by two F ions promote the polymerization of silicate melts. Keywords: fluorine; molten flux; slag structure; molecular dynamics simulation; Raman spectroscopy.

Jan 1, 2004

By M. A. W. Bryson

It is well documented that a significant amount of the new PGM (Platinum Group Minerals) production that is coming on stream now, and over the next few years, is to come from the UG-2 reef. Clearly the reservations, or perhaps the perceived reservations, attached to the processing of this ore are no longer there. What were the metallurgical issues that delayed the exploitation of the PGM values from this reef? Traditional furnaces treating Merensky concentrates were not able to accept the concentrate produced from a UG-2 plant due to the relatively high chromite content of this product. The chromite reports to an insoluble spinel phase that accretes in the furnace, resulting in the necessity to shutdown and dig the furnace out periodically. This was clearly not an attractive economic option, so producers stayed away from it in the early days. The Merensky ore had all higher base metal credits anyway, and you needed them to get a matte fall, so there was no driving force to look seriously at the UG-2 reef. Platinum demand at this time could be easily met from the Merensky ore, so the motivation to tackle more complex ores was not there. The low price of PGMs meant that these operations were not particularly profitable and there was little effort directed at improving the operations. Concentrators were generally not run very efficiently and the emphasis was on cost reduction through increasing milling rates.

Jan 1, 2004

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

By A. Aitio

Sustainable development is one of the central themes of the work of the World Health Organization; chemical safety is one of its important components. For more than 25 years, WHO has had specialized units for assisting member countries in dealing with their problems in chemical safety. For one of the units involved, International Programme on Chemical Safety, a reorientation is in progress to make best use of existing resources, and to prioritise the work to optimally correspond to the needs of the member countries. The risk assessment work of IPCS, and specifically, the work on chromium and chromium compounds, are discussed.

Jan 1, 2004

By M. Görnerup, M. Hayashi, S. Seetharaman, C. -Å Däcker

The mould flux plays a crucial role in the continuous casting operation of steel due to its multi-functional assignment as lubricator and heat flux controller. In reality, the commercial fluxes can fall short of the expectations of the operator. In such cases, the performance of the mould flux reduces production throughput in the casting machine. This paper presents the results of a study of two different commercial mould fluxes in continuous casting of steels. The results of online sampling during casting, as well as off-line measurements in the laboratory, are presented. Mould flux powder and slag samples from the caster have been characterized with respect to melting behaviour, interfacial tension and thermal diffusivity, using various measuring techniques. An experimental technique has been developed in order to simulate the melting behaviour of a flux in the mould, which has been found to be useful for qualitative studies. A cross-sectional view of different powders reveals that up to four different material layers may exist in the bed: a loosely packed powder layer, sintered layer, semi-solid layer and liquid slag layer. It is found that the melting rate of the mould flux is dependent on the liquid slag layer thickness. Thus, in a continuous casting operation the melting rate is likely to be non-uniform with position in mould due to the difference in liquid slag layer thickness. Mould slag composition is found to be influenced by the starting powder for as long as 30 min, representing a large part of the first heat casting time. Observations of gas formation indicate that interfacial reactions between the steel and slag take place. Keywords: continuous sacting, mould flux, mould slag, properties

Jan 1, 2004

By K. Ding

The thermodynamic activity of MnO was measured in MnO-CaO-MgO-SiO2slags that are typically encountered in the production of manganese containing stainless steels. Gas equilibration-quenching technique was employed in measuring the activities. Activity of Mn in Pt-Mn alloys were redetermined at 1600°C which reconfirmed earlier results of strong negative deviations. MnO activities were then measured by equilibrating slags of various compositions based on a statistical experimental design procedure with Pt-Mn alloys under controlled partial pressure of oxygen in MnO saturated platinum crucibles at 1600°C. Activities of MnO were found to increase with increasing concentration of MnO, basicity and CaO to MgO ratio. Two multi-coefficient repression models were developed to predict the activities and activity coefficients of MnO in slags at 1600°C. Keywords: activity, MnO, slag.

Jan 1, 2004

By V. Labiouse, P. K. Kaiser, F. Descoeudres, F. Rojat

In this paper some failure phenomena observed in the crossing of brittle rock formations at the Lötschberg base tunnel are presented. A brittle failure criteria, recently developed by Canadian researchers, is applied through finite element calculations together with a semi-empirical failure criterion, to explain these behaviours. Good agreement is found between predicted and observed failures at the tunnel walls. This study also shows some of the limitations of this approach. Dans cet article sont présentés certains phénomènes de rupture observés durant la traversée de zones de roches fragiles lors de l’excavation du tunnel du Lötschberg. Un critère de rupture développé récemment par la recherche canadienne est utilisé à travers des calculs par éléments finis. En parallèle, les résultats sont comparés avec ceux d’un critère semi-empirique. Au niveau des parements, l’ampleur des ruptures observées est assez proche des résultats de calcul. Cette étude a également permis de mettre en avant certaines limites de l’approche choisie. In diesem Artikel werden verschiedene Brucharten dargestellt, die bei der Durchfahrung von sprödem Gestein im Rahmen des Ausbaus des Lötschberg-Basistunnels beobachtet wurden. Zur Erklärung des vorliegenden Verhaltens wurden die erst kürzlich in Kanada entwickelten Theorien zur Beschreibung von Sprödbrüchen herangezogen und bei der Berechnung mittels der Finite-Elemente-Methode und eines semi-empirischen Kriteriums angewendet. Die so vorhergesagten Versagenszonen an den Tunnelwänden stimmen mit den Beobachtungen gut überein. Die Studie hat auch dazu beigetragen, die bei der Anwendung des Lösungsansatzes angetroffenen Schwierigkeiten aufzuzeigen.

Jan 1, 2003

By S. Pal, A. K. Lahiri

Most of the compounds present in slag are surface active. This gives rise to foaminess of slag. The foam life and foaming index are normally determined by the draining rate of slag through the plateau border, so the foaming index is directly proportional to slag viscosity and inversely proportional to slag density and bubble diameter. When a small amount of a strong surface active compound like P2O5or Cr2O3is present in slag, however, the foam life increases significantly and the above relationship is not obeyed. The strong surface active compounds reduce the draining rate from the film between the adjacent bubbles so the film draining controls the life of the foam. The thickness of the film, Marangoni force, viscosity of the slag, and diffusion of surface active compounds determine the film draining rate. The interplay of these factors leads to very low or high film draining rates and affects the film and foam stability significantly. Keywords: slag, foam, foaming index, film draining

Jan 1, 2004

By A. B. Fox, R. P. Thackray, K. C. Mills

The role of mould fluxes in continuous casting is reviewed. The main functions of the flux are described and the importance of the flux in providing lubrication and the right level of heat transfer between the shell and the mould is described. The major problems of longitudinal, transverse and star cracking, gas and slag entrapment and deep oscillation marks in the steel product and ?sticker breakouts? are analysed. The important physical properties of the flux in combating these various problems are identified. Physical property data for the fluxes are given.

Jan 1, 2004

By S. Erçayhan, B. Derin, O. Yücel

In the present study, the production of low carbon ferrochromium (LC-FeCr) from chromite concentrates containing 55.09% Cr2O3 and 13.06% Fe via metallothermic process was investigated. For this aim, in the experiments, the aluminothermic reduction method was applied in an open crucible. 10% CrO3 + 10% NaClO3, 15% CrO3 + 5% NaClO3 and 20% CrO3 by weight of concentrate were added to the charge, respectively and the charge was reduced with aluminium. The experiments were done with the additions of 90, 100, 110, 120 and 130% of stoichiometric requirement of aluminium. The highest Cr content in alloys was found as 71.7% at 120% of stoichiometric Al whereas the highest Cr recovery in alloys was found as 71.8% at 130% of stoichiometric Al when the both charge contained 15% CrO3 + 5% NaClO3 by weight of chromite concentrate.

Jan 1, 2004

By A. Kondratiev

A structurally-based viscosity model for fully liquid silicate slags has been developed and applied to the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation. The model links the slag viscosity to the internal structure of melts through second nearest neighbour bonds concentrations taken from the quasi-chemical thermodynamic model. This viscosity model describes experimental data over the whole temperature and composition ranges within the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation and can now be applied to other industrial slag systems.

Jan 1, 2004

By A. Beitz, P. Smartt, G. Einicke, G. Rowan, P. Glynn

Coal is Australia’s highest export earner and Australia is the world’s largest exporter of coal. With coal now being extracted from deeper reserves under increased risk profile, and in the interest of aiding the stability of coal supplies, Japan is funding a number of safety projects in Australia and China. The CSIRO, Australia’s premiere research organisation with the country’s largest exploration and mining research group, are currently undertaking a jointly funded Japan-Australia safety project at Anglo Coal’s new Grasstree Colliery in central Queensland. The project, entitled Mine Communication and Information for Real-time Risk Analysis, will deliver step-change capabilities in data integration, decision support, gas monitoring, geo-technical monitoring, emergency response and personnel safety to the Grasstree Colliery. Some key activities include: developing and installing underground coal mine Ethernet LAN components, real-time monitoring of gas and geo-technical sensors, MODBUS serial to TCP/IP converters, e-reporting of underground conditions, emergency guidance systems and underground trials of Internet Protocol telephone and video. The project seeks to integrate (in real time) key data sets from the comprehensive and diversified range of propriety system currently in use at mines (ventilation, strata, operations e.g. haulage, pumps, conveyors etc) into a single integrated risk management interface. This interface will filter the data through a rules-based inference engine that will cross reference the various data streams, compare with past events and outcomes associated with the similar historical data and present this “intelligence” to

Jan 1, 2003

By R. Hart

In this paper, problems that have been experienced with the rockpass system at Kloof Mine No. 3 Shaft are described. Actions that have been taken to overcome the problems are also described. These include the use of slugshots to remove hang-ups, the abandonment and waste filling of passes, and design criteria adopted for an alternative pass system.

Jan 1, 2006