Search Documents

By R. Poisel, C. Scavia, Preh A., W. Roth, M. Pirulli

ABSTRACT: Two methodologies for the three-dimensional simulation of the run out of rock avalanches are presented: one based on a granular approach and the other based on a continuum equivalent approach. An evaluation of the possible run out area of the Oselitzenbach landslide (Carnic Alps, Austria) has been carried out applying the two methodologies. The combined use of these two approaches makes it possible a comprehensive assessment of the run out area. RESUME: Deux méthodologies pour la simulation tridimensionnelle de la propagation des avalanches rocheuses sont présentées: la première est basée sur un modèle de type granulaire et la deuxième sur un modèle du continu équivalent. Une évaluation de la propagation éventuelle de l’avalanche de Oselitzenbach (Alpes Carniche, Autriche) a été réalisée en utilisant les deux méthodologies. Les résultats obtenus montrent que la combinaison des deux approches rend possible une analyse plus complète de la phase de propagation. KURZFASSUNG: Für die dreidimensionale Modellierung eines Felsmassensturzes (sturzstrom) werden zwei Methoden, eine granulare und eine kontinuumsmechanische Methode, vorgestellt. Beide Methoden wurden zur Abschätzung der Ausbreitung (runout) der Massenbewegung Oselitzenbach (Karnische Alpen, Österreich) herangezogen. Die kombinierte Anwendung beider Methoden ermöglichte eine umfassende Beurteilung des möglichen Ausbreitungsbereichs.

Jan 1, 2003

By J. Riss, S. Gentier, A. Marache

The study of the hydromechanical behaviour of fractured rock masses requires a detailed knowledge of the isolated fractures. The aim of the paper is the simulation of the evolution of the void space, located between both walls of a fracture, during a shear test under constant normal stress. Results of the mechanical simulation model are first validated then analyzed in detail. We observe that, during the shear process, there is an opening of the fracture with the creation of preferential channels. These channels are determined at the early phase of the shear process (pre-peak phase), and we observe during the post-peak phase that void areas increase in size rather than the creation of new apertures. Die Untersuchung des hydromechanischen Verhaltens eines zerlegten Felsmassivs erfordert genaue Kenntnisse der einzelnen Spalten. Ziel dieses Artikels ist die Simulation der Evolution des Hohlraumes zwischen den beiden Wänden eines Spaltes während eines Abscherungsexperimentes unter konstantem senkrechtem Druck. Die Ergebnisse der Modellierung werden zunächst mit dem Abscherungsexperiment verglichen und dann im Einzelnen ausführlich analysiert. Während des Abscherungsprozesses tritt eine Öffnung des Spaltes auf, die die Bildung von bevorzugten Fliesswegen fördert. Diese Kanäle werden bereits in einer frühen Phase des Abscherungsprozesses (pre-peak Phase) festgelegt. In der post-peak Phase tritt dann eher eine Vergrößerung dieser Kanäle, als die Bildung neuer Hohlräume auf. L’étude du comportement hydromécanique d’un massif rocheux fracturé ne peut se faire sans une connaissance approfondie des fractures le constituant. L’étude présentée dans cet article concerne la simulation de l’évolution de l’espace des vides présent entre les deux épontes d’une fracture au cours d’un essai de cisaillement à contrainte normale constante. Les résultats du modèle sont tout d’abord validés puis analysés en détail. On constate que, au cours du cisaillement, il apparaît une ouverture de la fracture permettant la création de chenaux préférentiels. Ces derniers sont déterminés très tôt dans le cisaillement (phase pré-pic), et on observe dans la phase post-pic davantage un accroissement de la taille des chenaux plutôt que la formation de nouvelles zones de vides.

Jan 1, 2003

By F. M. G. Egerton

Mechanisation of mining operations is not a new concept in the world of mining. Machinery has been developed, manufactured and used for many decades in massive orebodies and coal mines, both locally and abroad. Because of their size and the huge tonnages available, massive ore bodies lend themselves very easily to mechanisation. However, little progress in mechanisation has been made in narrow tabular orebodies in South Africa. The equipment available for narrow tabular orebodies requires excavations of a size that introduce large volumes of waste dilution. Nevertheless, it is essential for South African miners to experiment with mechanisation and to find a solution to the problem. This address looks at current conventional mining methods and compares them to bord-and-pillar type mining methods. Off-reef mechanisation is also touched on. It then looks at different hybridised mining methods that are being used, i.e. a mixture of conventional mining and mechanisation. It finally looks at future prospects for mechanisation in narrow tabular orebodies.

Jan 1, 2004

By L. J. Leach

Quench and tempered Cr-Mo plate steel was found not to contain a fully martensitic structure as a result of either slow slack quenching or insufficient hardenability at the cooling rates used. The resulting microstructure contains bainite in combination with martensite. It is necessary to examine the implications of bainite for the toughness of the final product. Loss of toughness arises primarily from the inter-lath carbides that typically form in upper bainite. An investigation into the effect of upper bainite in a martensitic matrix of a steel grade containing 0.17% C, 0.1% Cr, 0.54% Mo, and 20 ppm Bindicated lower toughness than in a fully martensitic structure.

Jan 1, 2013

Deep level block caving as a mining method is becoming more popular due to the fact that it is the lowest cost per ton underground extraction system. However, many block caves do not achieve their full potential due to draw horizon instability. In this paper five design rules are given to overcome this problem. The design rules described are applicable for slusher and trackless block caves where the operational depths exceed 500 metres.

Jan 1, 1999

By S. T. Johansen, C. Colomb, B. Ravary

Combustion and thermal NOx formation have been modelled using the Computational Fluid Dynamics (CFD) commercial code Fluent 6.1. The aim was to predict and give a better understanding of the combustion in electric arc furnaces for the production of ferro-silicon and silicon metal. Another important objective was to assess the impact of a number of operating parameters on the NOx formation. The CFD tools used are de-scribed with a special focus on models for species and turbulence transport. Sensitivity studies have been carried out to study the influence of several parameters: sub-models, process gas composition and distribution at the charge surface and influence of the presence of SiO. The main conclusions are: ?Using the combination of a realistic design, boundary conditions and models, the simulated NOx level is in quantitative agreement with measurements. The presence of water vapor is particularly important because of its influence on the specific heat of the mixture and resulting temperature. ?Release of significant amounts of SiO from the charge surface results in an important increase of NOx, even if we applied a simplified combustion model for SiO gas. However, because of lack of thermal and compositional data for blowing situations (when SiO flows directly from the arc cavity through open channels to the charge surface), no quantitative validation is possible. The way SiO is distributed (uniformly or as a jet) has a limited impact on the result in our computations.

Jan 1, 2007

By K. Sugawara, H. -S. Jeong, Y. Ishiguro, J. Otani, Y. Obara, A. Hirata

A series of measurements of induced stress by the Compact Conical-ended Borehole Overcoring (CCBO) technique was performed within rock mass around a tunnel excavated in a region that an underground powerhouse is constructed under high initial rock stress. In the measurements, a phenomenon of core disking was observed during overcoring. The selecting method of strain data uninfluenced by the core disking was proposed, using X-ray CT scanner. Then, the state of induced stress determined from the selected strain data was discussed, comparing with the state of initial stress. Eine Serie von Messungen von induzierter Belastung mit kompaktem konisch-beendetem Überbohrverfahren (CCBO) wurde in Felsmassen um einen Tunnel ausgeführt, der in einer Region gebohrt wurde wo ein unterirdisches Kraftwert unter hoher anfänglicher Felsbelastung gebaut wird. Bei den Messungen wurde beim Überbohrverfahren ein Phänomen des Core Disking beobachtet. Die gewählte Methode der Belastungsdaten, unbeeinflusst durch Core Disking wurde vorgeschlagen, unter Verwendung von Röntgen-CT-Scanner. Dann wurde der Zustand der induzierten Belastung aus den gewählten Belastungsdaten diskutiert, unter Vergleich mit der ursprünglichen Belastung. Une série de mesures de contrainte induite effectuée avec la technique de forage de sur-carottage compacte à embout conique a été exécutée dans la masse rocheuse autour d'un tunnel excavé dans une région de construction d'une centrale électrique souterraine sous haute contrainte de roche initiale. Au cours des mesures, un phénomène de discage de carotte a été observé pendant le sur-carottage. La méthode de sélection des données de contrainte non influencée par le discage de carotte a été proposée, en utilisant un scanneur de tomographie calculée aux rayons X. Il s'ensuit que l'état de contrainte induite provoquée et déterminé à partir des données de la contrainte sélectionnées a été traitée, en effectuant une comparaison avec l'état de contrainte initiale.

Jan 1, 2003

By M. A. van Nierop

Load behaviour in an industrial mill has been measured directly by inserting probes through liner bolts. The data from conductivity probes have indicated the presence of premature centrifuging during manipulation of the load mass. Overloading conditions were also encountered. Overloading and premature centrifuging both reduce the power drawn by the mill. These effects have been successfully modelled.

Jan 1, 1997

By D. F. Malan

This paper gives an overview of the difficulties associated with determining the strength of hard-rock pillars. Although a number of pillar design tools are available, pillar collapses still occur. Recent examples of large-scale pillar collapses in South Africa suggest that these were caused by weak partings that traversed the pillars. Currently two different methods are used to determine the strength of pillars, namely, empirical equations derived from back analyses of failed and stable cases, and numerical modelling tools using appropriate failure criteria. The paper illustrates that both techniques have their limitations and additional work is required to obtain a better understanding of pillar strength. Empirical methods based on observations of pillar behaviour in a given geotechnical setting are popular and easy to use, but care should be exercised that the results are not inappropriately extrapolated beyond the environment in which they are established. An example is the Hedley and Grant formula (derived for the Canadian uranium mines), which has been used for many years in the South African platinum and chrome mines (albeit with some adaptation of the K-value). Very few collapses have been reported in South Africa for layouts designed using this formula, suggesting that in some cases it might yield estimates of pillar strength that are too conservative. As an alternative, some engineers strongly advocate the use of numerical techniques to determine pillar strength. A close examination unfortunately reveals that these techniques also rely on many assumptions. An area where numerical modelling is invaluable, however, is in determining pillar stresses accurately and for studying specific pillar failure mechanisms, such as the influence of weak partings on pillar strength. In conclusion, it appears that neither empirical techniques nor numerical modelling can be used solely to provide a solid basis for conducting pillar design. It is therefore recommended that both these techniques should be utilized to obtain the best possible insight into a given design problem. Owing to the uncertainties regarding pillar strength and loading stiffness, monitoring in trial mining sections and in established mining areas is also an essential tool to test the stability of pillar layouts in particular geotechnical areas.

Jan 1, 2011

By G. S. Maré

Tin plating operations are of a complex nature due to the many operational variables that need to be controlled in order to create a product of required quality. The work in this report lays the basics for the control of a halogen plating operation based on the DuPont tinplating set-up with regard to the chemical make-up of the plating solution, as well as operational variables such as temperature and current density. To evaluate these aspects of the process, a rotating cathode Hull-cell set-up was used. This allowed for a laboratory scale plating arrangement that simulates industry closely with regard to chemical and hydro-dynamic considerations. Typical industry accepted standards were obtained for the values of operational variables and a ?baseline? test was conducted employing these standards. All subsequent tests conducted were benchmarked against this baseline result. A large suite of results was obtained in which it was found that changes could be made to the industry accepted norm which would improve on the stability of the operation and therefore the quality of the final tin-plated product. Examples of these results are: an increase in stannous tin concentration, an increase in sodium chloride concentration and a slightly elevated plating temperature. In addition, conditions were found that must be avoided to prevent instability and poor product quality.

Jan 1, 2010

By R. A. Williams

Electrical impedance tomographic methods have been applied to a variety of mineral and chemical processes in the laboratory and on plant. This review paper surveys technical developments in measurement methods to enable quantitative extraction of key process information in the form of mapping of concentration profiles, mixture homogeneity and suspension velocity. The methods for determining velocity are summarized, since this is of especial interest when applied to opaque systems where most conventional optically based measurements fail. A recent significant development is the use of ultra-high speed measurement that now allows velocity vectors to be extracted for fast moving mixtures and fluids (up to several metres per second). New data are reported pertinent to low and high solids concentration flow in pipelines. Use of the methods offer improvements to design of such systems but also points to the use of tomographic electrical sensor as online flow measurement and fault detection. This offers new opportunities for applications and benefits in the design and monitoring of mineral slurries and sludges.

Jan 1, 2008

By M. Steyn

[Zr(C9H6NO)4]?(HCON(CH3)2)?(H2O), where (C9H6NO) = 8-hydroxy quinoline (oxH), was synthesized and characterized. This tetrakis-coordinated zirconium complex crystallized in the triclinic crystal system (Pi, Z=2) along with water and N,N?-dimethylformamide(DMF) solvate in the asymmetric unit. The metal atom is surrounded by four N,O-donating bidentate ox-ligands that are arranged around the metal centre to give a square antiprismatic coordination polyhedron with a small distortion towards a dodecahedral geometry. Crystal packing is stabilized by intermolecular interactions of adjacent oxine ring systems in neighbouring molecules, as well as hydrogen bonding of the aqua and DMF solvate molecules, linking the molecular entities into a supramolecular three-dimensional network.

Jan 1, 2013

By J. Botin

Traditional risk quantification methods provide little information on the sources of risk, and tend to produce static over-conservative evaluations, which do not account for changes in the performance of the project. Capital investment decisions for large mining projects require more complex risk evaluation models that include the value of flexibility and the different risk levels associated with uncertainty on project variables (price, grade, dilution, and production rates, among many other). In this context, real option valuation (ROV) methods have proven potential to quantify the risk associated with such variables and integrate alternative scenarios and management strategies into the evaluation process. In this paper, a risk quantification model is developed that successfully quantifies the risk associated with dilution, as a function of production rate. This model is then validated in a case study on the Chuquicamata Underground Mine project. Keywords real options, risk management, risk quantification, dilution, minine planning.

Jul 1, 2013

By A. D. Storrie

An underground wet shotcrete trial was completed last year to determine the effectiveness of wet shotcrete as an alternative support mechanism to dry shotcrete in the kimberlite environment. The wet shotcrete was manufactured at the underground batch plants, transported to site using an agiecar and transferred to the shotcrete pump. The wet shotcrete is pumped to the nozzle where compressed air at 7 bar and an accelerator, Meyco SA 160, is added and enables the shotcrete to be placed successfully onto the tunnel wall. No tunnel guard was previously placed on the sidewall and hangingwall. Geotechnical testing indicates that the Grace fibre performed extremely well with the energy absorption tests at 7 kg/m3and 8kg/m3where both achieved over the mine requirement of 750joules. The Grace fibre and wet shotcrete mix also achieved a compressive strength in excess of 55 MPa, well above the 45 MPa requirement for Premier Mine. The recommended wet shotcrete mix design is therefore based upon: [Material/ CriteriaQuantity/m3Units ?Lafarge 42.5 Duratech500kg ?Condensed silica fume40kg ?Rayton Sand1.558Ton ?Delvocrete stabilizer 103.6litres ?Glenium 27CH5.4litres ?Meyco TCC 7355litres ?Water230litres ?Meyco SA16025litres ?Fibre8kg ?Cement/Water Ratio2.35? ?Water/Cement Ratio0.43? ?Flow615 mm] If the wet shotcrete system is implemented there is a potential for Premier Mine to make major savings. In South Africa there are two suitable wet shotcrete machines available for the mining industry, the Spreymec, manufactured by Tamrock and the Fermel/Meyco wet shotcrete machine. The Spreymec is a fully imported machine. The Fermel component is manufactured in South Africa and the Meyco shotcrete components are imported and supported by MBT (Master Builder Technologists) in South Africa. The Fermel/Meyco machine is assembled in South Africa. Premier Mine has allocated some R2, 100,000 towards the implementation of the wet shotcrete system. If implementation is successful there should be an internal rate of return gain of 76% with regard to this project.

Jan 1, 2001

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004

By P. Kluge

Mining engineers frequently encounter complex design problems for which the critical components of the design are difficult to quantify or compare. Teams of people typically work on these designs and human perceptions and judgments play a strong role. To assist with this process, the analytical hierarchical process (AHP) as a decisionmaking tool is described in this paper. Although the technique is used in many other disciplines, it is currently not widely used in mining engineering in South Africa. To use the AHP process, the problem should be treated as a hierarchy that defines the goal, the alternatives to reach it, and the criteria for evaluation of these alternatives. Pair wise comparisons are conducted on the criteria of the hierarchy to establish priorities. The value of the technique is that it is simple to test for consistency amongst the pair wise comparisons to ensure that the answer obtained is better than that provided by a random selection. To illustrate the technique, the use of a backfill support system in a platinum mining project was investigated. Ten design parameters, which will be impacted by the use of backfill, were identified and weighted according to their relative importance. The result of the AHP evaluation was that the use of a backfill support system should be preferred to a conventional support system at the mine.

Jan 1, 2011

By R. Abela

Heavy mineral sands are usually beneficiated in a spiral concentrator circuit prior to separation of heavy minerals into streams of zircon, rutile and ilmenite. The performance of the spiral concentrators is heavily affected by the presence of slimes in the rougher feed. The paper quantifies the effect of slimes content and discusses the beneficial effect of spiral feed de-sliming. The net effect of inefficient slimes removal can cause significant recovery losses of the heavy minerals present in the feed.

Jan 1, 2003

By J. J. Swanepoel

Titanium nitride in upgraded nitrided ilmenite (bulk of iron removed) can selectively be chlorinated to produce titanium tetrachloride. Except for iron, most other components present during this low temperature (ca. 200°C) chlorination reaction will not react with chlorine. It is therefore necessary to remove as much iron as possible from the nitrided ilmenite. Hydrochloric acid leaching is a possible process route to remove metallic iron from nitrided ilmenite without excessive dissolution of species like titanium nitride and calcium oxide. Calcium oxide dissolution results in unrecoverable acid consumption. The leachability of nitrided ilmenite in hydrochloric acid was evaluated by determining the dissolution of species like aluminium, calcium, titanium and magnesium in a batch leach reactor for 60 minutes at 90°C under reflux conditions. The hydrochloric acid concentration (11%, 18% and 25%), initial acid-to-iron mole ratio (2:1, 2.5:1 and 3.3:1), and solid-to-liquid mass ratio (1:8.33 to 1:2.13) were varied. The results indicate that a hydrochloric acid concentration of 25 wt% supplied in a 2:1 acid-to-iron mole ratio would produce the most favourable upgraded nitrided ilmenite product. The dissolution of iron in this solution reached 97 per cent after only 60 minutes. The total dissolution of calcium and titanium species was 0.01 and 0.11 wt% respectively. Hydrochloric acid can therefore be used as lixiviant to remove metallic iron from nitrided ilmenite. Keywords Titanium nitride, upgraded nitrided ilmenite, hydrochloric acid leaching, metallic iron dissolution.

Jan 1, 2011

By L. F. Contreras

In open pit mine design, it is customary for geotechnical engineers to define the appropriate slope design angles within practical limits. The conventional approach to slope angle design is based on the comparison of calculated stability indicators, such as the factor of safety (FS) and the probability of failure (PF), with generic acceptability criteria not directly related to the impacts of failure. A major drawback of this type of approach is related to the difficulty of defining meaningful acceptability criteria. An alternative methodology of pit slope design is proposed, where the economic impacts of potential slope failures are calculated and used as the elements on which to apply the acceptability criteria for design. The methodology is based on the construction of a graph, referred to as a risk map, that relates the probability of exceeding the economic impact of slope failure to the magnitude of the impact measured in monetary terms. The process includes the analysis of a selected number of representative years of the mine plan and slope sections of the pit areas to define the required inputs for the construction of the risk map. The paper discusses the concepts used in interpreting the probability of slope failure, and describes the approach followed for the estimation of the economic impacts of slope failure and the construction of the risk map. Finally, the two main uses of the risk map are discussed, including the comparison with acceptability criteria for the evaluation of a specific open pit design and the comparative analysis of open pit design options in terms of value and risk to identify optimum pit layouts.

Jan 1, 2015