Search Documents

By D. P. Venter

When Oryx Mine down-scaled in 1994, focus was placed on development, with the primary aim being the exposure and proving of ore reserves. In order to achieve this aim, development ends had to be advanced to reef at the maximum possible rate. This in turn called for support methods which could keep up with the advancing faces, taking up minimum space and time for installation, while providing on the face a real coverage and effective long-term support. In the majority of the development ends which were located in fairly competent ground, the grouted rod development support proved to be adequate until such time as secondary support in the form of meshing and lacing could be installed. The ends developing towards the eastern boundary of the mine, especially in the ?C? block, encountered extremely adverse ground conditions due to the presence of smectite zones within the footwall quartzites. Smectites are a group of montmorillonite clay materials, mainly composed of hydrous aluminosilicates. They occur as minute platy crystals in the rock mass and are especially notable for their ability to absorb liquids. Generally, the zones are found in between the bedding planes of the host rock, and may vary considerably in thickness over short distances. Wherever the smectites were exposed by the development blasting, the rockwalls weathered as the smectites absorbed water and the condition of the tunnel rockwalls deteriorated rapidly. When the smectites were left exposed and allowed to weather, it became almost impossible to install secondary permanent support such as meshing and lacing at a later stage. To minimise the exposure time and subsequent deterioration of the smectite zones, it was recommended that all development ends encountering smectites be shotcreted as soon as possible after blasting. In developing a shotcreting support methodology, both a drycreting and wetcreting system were investigated. The situation at the time ruled out the use of a wetcreting system on the basis of the extensive and costly infrastructure required, as well as its limited manoeuverability. Instead, it was decided to opt for as maller scale but more manoeuverable drycreting system. The system utilized a number of portable drycrete machines with pre-bagged cement, which could support several development ends in close proximity. Initial trials using normal 30 MPa shotcrete on 19level proved successful and the system was implemented.

Jan 1, 1998

By S. M. Spottiswoode

Crush pillars are widely used in mine workings on the Merensky Reef in the Bushveld Complex to prevent panel collapses. Crush pillars are expected to fail as or soon after they emerge from the face and failure should occur non-violently. Unfortunately, violent failure occurs frequently and is said to be the main cause of seismicity associated with mining of the Merensky Reef. Recent work by Napier, Malan, and du Plessis has shown that limitequilibrium quasi-static models are able to simulate pillar failure using three states of strength of rock in pillars, namely intact, residual after failure, and decayed strength after later time-dependent (viscous) weakening. We have previously introduced an additional state of strength to account for the dynamic failure that results in seismic events, and found that this approach could be used to generate synthetic seismic catalogues similar to observed seismicity for deep-level gold mines, where seismicity takes place mostly on advancing faces. The less brittle seam material of the Merensky Reef, compared to the brittle quartzites and lavas of the Witwatersrand reefs, results in little or no face bursting and is modelled with an assumed plastic strain of some 0.005 over an effective stope width of 2 m before failure. When this plastic yield is surpassed, we allow the reef to fail ?seismically?. We show that synthetic seismic catalogues modelled in this way have some of the features of observed seismicity. Analysis is greatly facilitated using our custom-built software that reads the mine?s survey data into a database and presents results in an interactive graphical form.

Jan 1, 2014

By S. Frimpong, S. R. Dindarloo

Material handling in open pit mining accounts for about 50% of production costs. The selection and deployment of efficient, safe, and economic loading and haulage systems is thus critical to the production process. The problems of truck and shovel selection and sizing include determination of the optimal number and capacities of haulage and loading units, as well as their allocation and operational strategies. Critical survey and analysis of the literature has shown that deterministic, stochastic, and experimental approaches to these problems result in considerably different outputs. This paper presents a comprehensive simulation framework for the problem of truck and shovel selection and sizing based on the random processes underlying the network-continuous-discrete event nature of the mining operation. The framework builds on previous research in this field and attempts to address limitations of available methodologies in the form of a comprehensive algorithm. To test the validity of the framework a large open pit mine was evaluated. The stochastic processes governing the uncertainties underlying the material loading and haulage input variables were defined and built into the stochastic model. Discrete event simulation was used to simulate the stochastic model. The proposed model resulted in several modifications to the case study.

Jan 1, 2015

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009

The Mineral Density Separator (MDS) was developed by Mintek to predict mineral separation in a plant, evaluate efficiencies and develop scale-up parameters. This study investigated the influence of particle size on the results of the MDS, the misplacement of material in the MDS and the possibility of replacing heavy liquid float and sink analyses of coal with MDS analyses. Six tests were done with coal of different size ranges. Each MDS layer was subjected to a float-sink analysis whereafter each float fraction was screened to determine the particle size distribution. The results indicated that MDS results represent float-sink analyses when compared to an ash curve. There is some misplacement in the different MDS layers, but this does not seem to influence the results negatively. Keywords Mineral density separator, sink-float analyses, heavy liquid analyses, washability curve

Jan 1, 2006

By A. Kostin

GIS and multivariate geometric distribution have been used to predict the association of high-level intrusives with hydrothermal alteration related to iron oxide Cu-Au (IOCG) mineralizing systems. Several examples in the Russian northeast are presented in this paper. IOCG ore deposits can have enormous geological resources containing significant reserves of base, precious, and strategic metals, and hence are economically attractive targets for mineral exploration. To date, examples of this type of mineralization have not been reported from the northeastern area of Russia. The Tarinskiy ore cluster, located in Eastern Yakutia, shows brecciated altered rocks with sulphide and iron oxide cement, which is typical for IOCG mineralization of the iron oxide Cu-Au±U type. This cluster was formed near surface and is linked with the Rep- Yuruinskiy pluton. It has potential to host new world-class precious metal deposits in northeastern Russia

Jan 1, 2014

By R. Cao

Geostatistics was initially developed in the mining sector, but has been extended to other geoscience applications, including forestry, environmental science, soil science, and petroleum science and engineering. This paper presents methods, workflows, and pitfalls in using geostatistics for hydrocarbon resource modelling and evaluation. Examples are presented of indicator variogram analysis of categorical variables, lithofacies modelling by sequential indicator simulation and hierarchical workflow, porosity modelling by kriging and stochastic simulation, collocated cokriging for integrating seismic data, and collocated cosimulation for modelling porosity and permeability relationships. These methods together form a systematic approach that can be effectively used for modelling natural resources.

Jan 1, 2014

By J J. McEwan

Silver tarnishes readily in common atmospheres and is accelerated in humid atmospheres. Tarnish is the formation of silver sulphide on the surface of silver when it is exposed to a wide range of sulphur-containing atmospheres. Tarnish is unattractive and highly undesirable, and can be removed either with a silver polish or a chemical dip. Dips are generally only recommended when heavy black tarnish cannot be removed with a polish, and care must be taken during cleaning because these can contain aggressive chemicals and give off hazardous and unpleasant smelling fumes. Polishes work best for large areas of plain undecorated silver, and form part of a regular cleaning programme. Some polishes contain chemicals that inhibit tarnishing, but these generally only have a short life. Several methods have been developed to reduce tarnish formation on Silver; these include alloying, surface treatment, and coatings. The authors evaluated a range of self-assembled monolayer (SAM) surface treatments and coatings in earlier research. Four treatments/coatings increased the time to noticeable tarnish by more than ten fold, and the results were reported at the International Corrosion Congress (ICC) in 2005, and at the Mint Directors Conference (MDC) in 2006. SAM treatment using 95% 1-hexadecanethiol (C16H34S) was found to give good anti-tarnish performance and showed potential for the commercial treatment of Sterling silver. Therefore research was performed to optimise the methods of application of this type of coating to provide an easier, faster, and more-user friendly technique to provide an anti-tarnish treatment. Keywords: silver, tarnish resistant coatings.

Jan 1, 2006

By G. I. McPhail

The authors have conducted several investigations into the prediction of the beach profile of high-density tailings and have found that there are a number of important considerations that need to be taken into account over and above the reliability of the beach profile prediction methodology. These considerations relate to the chemistry of the slurry and specifically the influence of pH and flocculation, both of which have a significant influence on the rheology of the slurry at the discharge point. A number of examples are discussed and a potential testing protocol that will assist in assessing the influence of chemistry ahead of the beach profile predictions is presented. A methodology for assimilating the results of the testing into the likely field situation is discussed, and suggestions are made on application of the results in beach profile prediction. The suspected influence of residual flocculation on the stratification

Jan 1, 2012

By J. T. Nel

Non-transfer-arc linear plasma systems are highly suited to manufacturing nanoparticles. In this paper, the manufacturing of such particles with specially designed plasma systems is discussed. In general, it entails the volatilization of a metal halide that is injected in the high-temperature region of a plasma flame, where it is reacted with a suitable reagent, for example O2, to produce nanooxide powders. Metal powders can also be introduced directly in the plasma. Due to the very short residence time of only milliseconds in the reaction zone, as well as the fact that the reaction takes place in the gas phase, combined with very rapid quenching in the order of 10 000°C.s-1, nanoparticles are produced. At Necsa the manufacturing of such particles has been demonstrated on various scales. A pilot plant for the production of nano-Al2O3, and two pilot plants, one using SiCl4 and the other one using SiF4 as feed material, were built to produce fumed, pyrogenic, nano-SiO2. The alumina plant had a production rate of 8?10 kg.h-1 and the silica plants had production rates of 2 and 10 kg.h-1 respectively. Perfectly spherical alumina particles with a particle size distribution of between 10 and 200 nm were produced on a continuous system. Particle size analysis for the silica by SEM measurements showed a d50 of 60 nm and a particle size distribution of 30?100 nm. The specific surface area was in the range of 170m2.g-1. Other samples of plasma produced nanoparticles such ZnO and B4C will also be presented.

Jan 1, 2010

By L C. Pretorius

Pipe pigging is a technique for the in situ (field) coating application, to create a seamless internal anti-corrosive lining of long pipelines. The technology originated in the cleaning of pipes, and these proven cleaning methods continue to be used today. Firstly mechanical cleaning of the pipeline is performed, using wire brush, razor back, course stud and fine wire pigs, then foam pigs, or criss cross pigs, and urethane blade scrapers to remove loose debris, wax, residual hydrocarbons and corrosion products from the pipeline. Part of the proprietary techniques and expertise is to ensure that these cleaning pigs do not get stuck Next chemical cleaning of the pipeline is performed, using repeated pig runs with detergents, solvents, acid etching, corrosion inhibitors, consecutively batched between two pigs, to ensure a clean, dry metal finish to a visual cleanliness standard of ISO SA2½. These in situ techniques were developed, 40 years ago to apply internal corrosion protection to pipes using a thin layer of epoxy based paint (50 to 100 micron). Until recently these old techniques were never improved upon. Although many thousands of kilometres of pipes were successfully coated with these thin film epoxy based paints and old application techniques, these thin paint films had problems in weld coverage, and were also unable to fill pits caused by pitting corrosion, and unable to replace metal loss caused by channel erosion. New coating material developments, revised application methods and modified pigging equipment have now made it possible to apply thick film coatings as corrosion barriers to the internals of pipes in the field, using these pigging techniques. The thick coating films can be up to 1 mm (40 mils) thick in a single coating run over long distances. The new thick film coating materials and application techniques are similar to continuous screeding, creating a far more robust seamless internal pipe lining when compared to the old technology of thin film paints. With thick film polymers the option now exists to create a structural GRP pipe within a pipe, be it steel or cementicious. It has been preferable, even necessary, to move away from the traditional epoxy paints and coatings. It was found difficult or impossible to use epoxy materials for these pipe coating applications due to the requirement for achieving a suitable viscosity with adequate hold up. In order to reduce epoxy viscosity a solvent or reactive diluent is required. This inevitably lead to solvent entrapment and poor cure characteristics in cold climates. Further mud cracking in over thick areas, the inability to extend or reduce pot life, poor control of cure time and limited resistance to aggressive or chemical environments made solvent based epoxy resins a poor choice.

Jan 1, 2006

The paper examines the design issues associated with the integration of mineral processing within underground mining systems. It demonstrates conceptual integrated system design options appropriate to a range of geological scenarios. Particular reference is then given to a case study of stoping in narrow base metal veins. The performance of such integrated systems in terms of productivity, economic and environmental criteria is demonstrated by means of simulation. Particular attention is given to the potential benefits to mine waste management. Processing technologies appear to offer genuine potential benefit, whilst underground mining methods may need to evolve further to facilitate full integration. This paper is based on industry supported research aimed at developing selective and clean underground mining systems.

Jan 1, 2003

The Mineral Sector Development Project, sponsored by the World Bank, has been set up to revise the legal, regulatory and fiscal framework for the minerals industry in Tanzania, with a view to attracting mining companies and investors to the country and facilitating future minerals development. One component of this project, the Environmental Management Framework for the Mineral Sector, was awarded to Wardell Armstrong of the UK and ENV Consult of Tanzania. In developing a new framework of environmental regulations, emphasis was placed on developing realistic standards which reflect local conditions and prevailing values. The main corner-stones of this approach are; effective environmental impact assessment procedures; establishment of environmental management procedures; and monitoring and auditing of companies? performance. The favoured approach involves a three-tier framework, as follows: ?Framework environmental provisions within the new Mining Act; ?Regulations covering more detailed environmental requirements ?Guidelines and/or Codes of Practice, which may in future become regulations in their own right. Careful consideration has been given, in developing the framework, to the limited resources likely to be available for implementation to the Ministry of Energy and Minerals and this has influenced the approach that has been adopted. This paper outlines the main components of the environmental management framework and discusses some of the important issues raised by these proposals.

Jan 1, 1998

By J. Krzyzanowska

Paper written on project work carried out in partial fulfilment of Bachelor of Engineering-Mining Venetia Mine, an open-pit diamond mining operation in the Limpopo Province of South Africa, currently has a mixed haul truck fleet consisting of Caterpillar 785B and C; 789C; modified 793D and 793D. Even in an ideal situation these trucks have different cycle times, which causes queuing at the loading area and their different speeds cause bunching on the ramps, leading to higher overall cycle times and lower productivity. This problem was identified but the root causes of the problem were not investigated and quantified. A time and motion study on the haul trucks was thus undertaken to measure actual cycle times and compare them to ideal cycle times as well as to observe any reasons for deviations. Ideal cycle times are partly evaluated on the basis of simulation and partly from production optimization expert input. Several areas that affect production were identified and these include: haul road conditions, the control room, dispatching programme and dispatching data management, as well as truck-shovel matching. The investigation was important in establishing control parameters for haul fleet operation since time spent queuing is production time lost, which defers waste tonnes to later in the life of mine, thus decreasing the tempo at which kimberlite is exposed.

Jan 1, 2007

Models are used in engineering to reproduce reality as faithfully as possible so that the expected response of a system for given actions or inputs can be determined. In the field of rock engineering, both empirically based and numerical models are widely used to determine the likely response of the rock surrounding excavations. Many of the empirical models are developed from statistical analysis of case histories or from direct observation; however, empirical models are limited because they should be used only within the range of conditions of the observational database. Synergy exists between empirical and numerical models, because empirical models can be used to calibrate and validate numerical models. The empirical approach can benefit from the capability of numerical models to investigate specific mechanisms, which would not be possible using observations alone. Two cases are presented in which the synergy between empirical and numerical models is demonstrated. The first case examines the analysis of discontinuity effects on the strength of slender pillars in limestone mines, and the second case evaluates the effects of stress orientation on coal mine entry stability. It is concluded that numerical model calibration and verification comprises an important first stage in the successful application of models in rock engineering design. Application of numerical models allows mechanisms and interactions of various parameters to be analysed, greatly improving the understanding of the system. The improved understanding can be used to extend the application of empirical design methods, resulting in improved safety and efficiency of rock engineering designs.

Jan 1, 2014

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

By M. Dworzanowski

The physical beneficiation of iron ore that has a wide particle-size distribution is problematic, regardless of the process applied, whether dense medium separation, gravity concentration, magnetic separation, or flotation. The problem of particle size is further compounded when there is a significant -10 µm fraction. Generally the approach to a wide particle-size distribution is to split into narrower size ranges and treat each separately. More often than not the -10 µm fraction is not treated but discarded. This approach results in a more complicated and expensive flow sheet and the loss of any potential value in the -10 µm fraction. Wet high-intensity magnetic separation (WHIMS) bench-scale test work was conducted on a haematite-rich material with a particle size of -200 µm. What made this material different was that it contained a 60% -10 µm fraction, hence discarding the -10 µm material was not an option. The objective of the test work was to determine how to maximize the recovery of the haematite across the full particle size range. Given the unusual particle size distribution, it was concluded that WHIMS would be the only practical beneficiation route. The -200 +10 µm and -10 µm fractions were treated separately and together under varying WHIMS conditions. For a given concentrate grade, the mass yield obtained was greater when the total particle-size distribution was treated. The inferred optimum conditions, using the same material, were tested on a pilot-scale WHIMS and similar results were obtained.

Jan 1, 2014

By D. van Rensburg

Jointed rock slopes are generally stable, as there is no freedom of movement for blocks of rock. In an open- pit mining environment, blasting opens up space into which blocks of rock can fail, resulting in the common occurrence of slope failure. Prior to the blasting of a trim pattern, the immediate highwall is scaled, where loose rock material is removed by means of a mechanical scaler. As mining of the pit progresses, the height of the scaled highwall from the pit floor progressively increases. These highwalls are never scaled again for the remainder of the pit life, and time-dependant deterioration contributes to these highwalls becoming subject to rockfall and, sometimes, slope failure. This paper documents the development of a South African innovation, a remote-controlled mechanical highwall scaler, a world first for the mining industry. The scaler will enable open-pit highwalls to be scaled from crest to toe whenever the need arises. It will reduce the risk associated with highwalls and deliver on the Anglo American promise of producing safe, profitable platinum.

Jan 1, 2012

By P. J. N. Pells

A good thing is becoming a bad thing. Rock mass classification systems, that are so excellent for communications between engineers and geologists, and that can be valuable in categorizing project experience, are emasculating engineering geology and rock mechanics. Some engineering geologists have been sucked into thinking that Q and RMR values are all that is needed for engineering purposes, and seem to have put aside what can be learned from structural geology and geomorphology. Many rock mechanics engineers seem to have forgotten the scientific method. This paper attempts to redress the situation by showing how mechanics can be used in rock engineering to design with a similar rigour to that used in the fields of structural engineering, hydraulics and soil mechanics. It also attempts to remind practitioners of what can be achieved by skilled engineering geology.

Jan 1, 2008

By J. Trckova, P. Prochazka

Physical models from equivalent materials satisfying geometrical and physical similarity have been constructed. A special technology of simulating the excavation of an opening at the front part of a tunnel and of measuring the deformation at the tunnel face was applied. The results yielded by the physical models were used to formulate constitution relations in the numerical solution. This coupled modelling enables us to predict the behaviour of tunnel structures more accurately. On a construit des modèles physiques, réalisés en matériaux équivalents et répondant aux conditions de ressemblance géométrique et physique. Sur ces modèles, on a utilisé une technologie intéressante de simulation du forage du tunnel et de la mesure de déformation du front de taille pendant le forage en progression. Les résultats donnés par les modèles physiques ont été utilisés pour formuler les relations de constitution dans la solution numérique. Une telle construction de modèles combinés permet de prévoir plus précisément le comportement de la structure du tunnel. Es wurden physikalische Simulierungsmodelle aus äquivalenten Werkstoffen konstruiert, welche die Bedingungen der geometrischen und physikalischen Ähnlichkeiten erfüllen. Bei diesen Modellen hat man die interessante Simulationstechnologie des Tunnelvortriebs sowie die Verformungsmessung beim Tunnelabbaustoß während des Vortriebsvorgangs eingesetzt. Die Ergebnisse der physikalischen Simulation wurden zur Formulierung von Konstitutionsrelationen in der numerischen Lösung genützt. So eine kombinierte Simulation erlaubt eine genauere Prognose des Benehmens der Tunnelstruktur.

Jan 1, 2003