Search Documents

By A. Mehmet

The feasibility of employing a multi-stage column for the recovery of gold from cyanided pulps using extruded carbon was investigated on a pilot-plant scale. It was anticipated that the column contactor would have certain advantages over conventional carbon-in-pulp plants. The feed pulp was screened to remove particles larger than 200 µm and was diluted to a solids concentration of about 23 per cent. The column was operated continuously for 24 days at a pulp flowrate of about 60 l/min and a carbon flowrate of 44 litres per day. The average gold concentrations in the barren pulp 12 hours and 24 hours after the carbon transfer were 0,012 and 0,031 mg/l respectively. The average gold concentration in the solution phase in the feed was about 2,0 mg/L. The average gold Loading on the carbon was 6290 g/t. Calcium carbonate was removed from the loaded carbon by treatment with 0,5 bed volumes of 2,8 per cent hydrochloric acid solution at ambient temperature. The calcium concentration was reduced from about 17 000 to about 500 g/t The carbon was eluted by the Zadra procedure at atmospheric pressure. The results of the elution were highly satisfactory, the gold concentration being reduced from about 6000 to about 20 g/t in 48 hours. The eluted carbon was regenerated in a Rintoul kiln at about 700°C. The activity of the regenerated carbon was found to be at least as high as that of fresh carbon.

Jan 1, 1992

By J. Sehata, J. Tshilongo, I. Govender, S. Pikinini, T. L. Moodley, M. Raedani

In the face of dwindling Merensky ore reserves in the early 1990s, Mintek developed the MF2 flotation circuit to economically recover platinum group metals from the shallow upper group-2 chromitite reef. By aligning the primary and secondary grind to the platinum group metal liberation kinetics, excessive fine chromite generation was avoided, and thus one could consistently produce high-grade concentrates (>200 g/t platinum group metals) with low chrome content (<3% Cr2O₃), well within smelter tolerances. This, coupled with upper group- 2's low-cost open-pit mining, made it particularly attractive to investors and mining houses alike. As a result, deeper lying reefs like middle group and lower group with lower platinum group metals grades and complex mineralogy, were primarily mined only for chromite using density-based separation processes (like spirals), of which the waste tailings are best classified as secondary platinum group metals resources. Today, with global platinum group metal demand rising and high grade upper ground-2 reserves rapidly diminishing, the industry must revisit these middle group and lower group tailings. Mineralogical analysis reveals several challenges: Middle group tailings feature platinum group metals locked within silicate matrices, while lower group tailings contain fine chromitite fragments, and are hosted within non-floating laurite grains, each presenting liberation and gangue issues. Smelter constraints still demand concentrates below 3% Cr₂O₃, requiring solutions that consider both platinum group metals recovery and chrome entrainment. To develop a solution, two lower group chrome spiral tailings samples were obtained from a large chrome mine: Sample A (+425 μm – 106 μm) and Sample B (−106 μm). Initial assays showed Sample B contained higher platinum group metal grades but also higher Cr₂O₃. As such, different blends of flotation feeds were evaluated using ratios of 90:10 (C1) and 80:20 (C2) of Sample A to Sample B, targeting the coarse fraction's lower chrome content while recovering valuable platinum group metals from the fines. This work proposes a practical route for mining houses to unlock additional platinum group metal value from lower group ore spiral tailings. By optimising blending ratios and reagent suites, it is possible to meet smelter chrome and platinum group metal grade thresholds, whilst still obtaining economically viable PGM recoveries.

Mar 6, 2026

By M. Rudolph, E. Schach

Tecflote is a new group of nitrile-based collectors for sulfide flotation. Water insolubility results in some interesting implications for the actual mechanism. It is not yet understood if Tecflote is directly adsorbed on the mineral surface as emulsion droplets or if it is only active at the air-water interface, affecting the interfacial rheology or electrostatic- and Van der Waals interactions, which have a direct impact on the bubble-particle contact. Different investigations including contact angle measurements, AFM studies and micro-flotation experiments are conducted to obtain a better understanding of the actual mechanism of Tecflote. Due to the reagent’s insoluble character, the Langmuir-Blodgett technique is used to investigate its behaviour in the air-water interface and to deposit defined layers of Tecflote on mineral substrates for the above-mentioned studies. An interferometric set up is used to investigate the influence of Tecflote on the film thinning between an air bubble and a mineral substrate. In addition, possible synergistic effects for the combination of Tecflote and conventional frothers (e.g. MIBC) are studied. Keywords: Sulfide flotation, insoluble collector

Jan 1, 2020

By L. Ozdemir, B. Asbury, T. G. Rozgonyi

A new type of bit, that has been developed and is being evaluated, shows great potential in expanding the range of rock strength that can be cut by continuous miners and roadheaders. This new style of bit is called the frustum. The tools tested in this program were developed, manufactured and patented by Briese Industrial Technologies, Inc. The frustum derives its name from the unique geometric shape of the cutter, or cutting insert. The frustum shape cutting tool has previously been proven as an effective cutting tool for machining metals, metal matrix composites and polymers. The frustum rock bit has a very dense carbide frustum shape tip mounted on the end of a steel body similar to the conical bits typically used on continuous miners and roadheaders. In between the carbide frustum cutting tip and the steel body there can be a bearing that allows the frustum to rotate around the bit axis. When the bit is forced into the rock at a skewed angle, the frustum tip rotates as it travels. This rotation greatly reduces the cutting forces acting on the bit when compared to the current state of the art conical drag bits. This cutting force reduction, derived from the frustum’s cutting action, allows for much harder and more abrasive rock to be cut without quickly wearing out the bit. Full scale laboratory cutting tests have been performed with the frustum bit in direct comparison to the current state of the art conical bits. Field trials of the frustum bit are currently being planned. Test procedures, results and findings are presented.

Sep 1, 2001

By H. Zhong, S. Wang, Q. Lin

To improve the flotation performance of chalcopyrite collector, 2-(tert-butoxy)ethyl xanthate (TBEX) and its derivative O-(2-(tert-butoxy)ethyl)-N-ethyl-thionocarbamate (TBEETC) were designed and prepared by the introduction of a 2-(tert-butoxy) ethyl group into xanthate and thionocarbamate. TBEX and TBEETC were both prepared via the one-pot method with superior efficiency, which has significant commercial implications. The micro-flotation tests demonstrated that compared with sodium isobutyl xanthate (SIBX) and O-isopropyl-N-ethyl-thionocarbamate (Z-200), TBEX and TBEETC both possessed better collecting ability and selectivity for chalcopyrite. DFT calculations and XPS were utilised to investigate the flotation mechanism involving TBEX or TBEETC and chalcopyrite. The results demonstrate that although 2-(tert-butoxy) ethyl group does not interact with minerals directly, its introduction reduces the energy of HOMO, so that they can better accept electrons instead of donating electrons which leads to better interaction with copper atoms rather than iron atoms. Keywords: Chalcopyrite, flotation, thionocarbamate, xanthate, synthesis

Jan 1, 2020

By Z. Botha

Sheryl Sandberg, the COO of Facebook, published a book titled 'Lean In', where she invites women to sit at the table. In summary, to 'sit at the table' entails not only embracing opportunity, but to actively seek out opportunities in leadership positions. Sandberg points out that, unfortunately, apart from institutional obstacles, a woman's own perceived limitations have a negative impact on her leadership ambitions. To create an environment where diversity will flourish, where everyone has a seat at the table and everyone has a voice, safety must be established first. To establish safety within a diverse team, there is power in relationships and connections. This study will first and foremost review theories in literature as to why diversity and inclusion are so important and the value that diversity brings to our industry. The study also recommends a few focus areas for improving diversity and inclusion in the industry.

Sep 1, 2022

By S. Krishnannair

Singular Spectrum Analysis (SSA) is an effective data-adaptive multimodal tool for monitoring chemical processes. However, monitoring multiscale signals using principal component analysis obtained from the multilevel decomposition of process signals using basic SSA assume the upper control limits of monitoring charts (" ) to have a Gaussian distribution. This assumption deteriorates the performance of basic SSA when applied to the monitoring of nonlinear processes. To address the issue in this paper, the kernel density estimation (KDE) was used to estimate upper control limits of monitoring charts for basic SSA based nonlinear process monitoring techniques. The monitoring performance of the resulting basic SSA-KDE approach was then compared with a basic SSA approach of which upper control limits of the monitoring charts were determined based on a Gaussian distribution. Application on nonlinear dynamic simulated process and base metal flotation plant chemical processes showed that the SSA-KDE approach provided better overall performance than the SSA approach with Gaussian assumption-based upper control limits for its monitoring charts. Keywords: Fault detection, singular value decomposition, singular spectrum analysis, kernel density estimation

Jan 1, 2020

By B. W. Wallace

Permitted explosives in South Africa are those explosives approved by the relevant State authority for use in fiery coal mines. The main tests that an explosive must pass for this approval are the gallery tests derived from the Buxton (U.K.) classification. These tests are described briefly. In addition, the safety of permitted explosives is affected by their ability to deflagrate, and to produce a naked flame after blasting, rather than to detonate fully. Tests done on this phenomenon are discussed. A further potential hazard of explosives is after-blast fume. The testing and behaviour of several permitted explosives in this respect are covered, both in the laboratory and in the field. Performance testing of permitted explosives, specifically the double-pipe, underwater, and ballistic mortar tests, and their relationship to field use, are considered in some detail. The application of traditional and new tests to permitted explosives leads to guidelines for the safe and efficient formulation and use of these products.

Jan 1, 1986

By S. A. Hosseini, O. Asghari

"The quantification of mineral resources and evaluation of process performance in mining operations at Gole Gohar iron ore deposit requires a precise model of the spatial variability of three variables (Fe, P, and S) which must be determined. According to statistical analysis there are complex multivariate relationships between these variables such as stoichiometric constraints, nonlinearity, and heteroskedasticity. Due to the impact of these complexities in decision-making, they should be reproduced in geostatistical models. First of all, in order to maintain the compositional and stoichiometric constraints, additive log-ratio (alr) transformation has been applied. In the next step cosimulation, using stepwise conditional transformation (SCT) and sequential Gaussian simulation (SGS) has been used to simulate multivariate data. Through statistical and geostatistical validations it is shown that the algorithms were able to reproduce complex relationships between variables, both locally and globally. IntroductionThe key steps in mining projects are the quantification of mineral resources, definition of mining reserves, and production scheduling. They rely on the construction of a block model that is used to represent basically the spatial distribution of ore grades (Montoya et al., 2012). The determination of grades and tonnages affects risk assessment and economic evaluation of mining projects. Evaluation of process performance in mining operations requires geostatistical modelling of many related variables (Barnett and Deutsch, 2012). Iron ore quality is characterized by multiple variables: not only the iron grade but also the contaminants that interfere in the subsequent steel manufacturing processes. Consequently, the spatial variability of multiple variables must be determined. Key variables are frequently correlated, and such correlations must be honoured during estimation and simulation. Data from iron ore deposits constitutes compositional data; furthermore, relationships the between assay data are often heteroskedastic."

Jan 1, 2016

By R. B. Khumalo, F. K. Mulenga

Sampling in a continuous flotation plant is always a challenge as these plants are meant for production and not research work. The continuous flotation operation used in this work produced three sets of data: the first was based on overall plant performance, done by sampling the feed, concentrate, and tails; the second was based on the roughers row cell-by-cell; the third set of results came from the cleaners/recleaners row cell-by-cell. The highest recovery results in all sets of data obtained lie in the particle size ranges of 40 μm and 100 μm, which is in agreement with results by other researchers in the same field. King’s theoretical (model) recovery proved to be able to fit the experimental data but there is still room for improvement as the sum of squared error ranged between 400– 1200. Data obtained in continuous flotation operation could be used with batch flotation test-work to characterize scale-up of flotation cells.

Jan 1, 2023

By J. R. Percival, L. Ip, M. D. Piggott, S. J. Neethling

Component wear due to particle-laden flow is a significant challenge in the minerals processing industry in the handling and transportation of abrasive mineral slurries. Studying wear through experimentation is time-consuming and expensive; therefore possessing the ability to accurately simulate, understand and predict wear in these complex environments is highly desirable. The ability to predict wear is important in both the design of equipment in order to maximise the performance over the wear life of the components, as well in minimising potentially costly and dangerous failures and unscheduled maintenance.. Particle-induced wear is a complex problem, requring an understanding of coupled fluid-solid motion, geometry deformation in response to fluid-solid behaviour, moving geometries and wear modelling. Although the literature demonstrates that rebounding particles and changes to surface profiles can have a significant effect on subsequent wear rates and patterns, the challenge of implementing a model to account for this effect in complex geometries has been addressed by only a few authors in the literature. This paper describes a new wear simulator, leveraging fluidity, an open-source, massively parallel, finite element based CFD simulator capable of unstructured adaptive meshing. The wear simulator includes the ability to model particle-laden flow using representative Lagrangian particles and dynamic remeshing of geometry in response to wear and component movement. These capabilities are demonstrated using wear and the associated dynamically deforming boundaries within a Coriolis tester arm, with the results comparing favourably with the experimentally observed wear patterns. Keywords: CFD, wear, two-phase flows, anisotropic mesh adaptivity, boundary deformation

Jan 1, 2020

By C. M. G. Wortley

One of the major deliverables of the AMIRA P754 Project, which was sponsored by several major mining companies, was a code of practice and guidelines for metal accounting for the mining and metallurgical industry. These had the objective of improving the auditability and transparency of metal accounting from mine to product, thus assisting in good corporate governance. The overriding objective of mass measurement for metal accounting is to establish the mass of the particular material or component present at a specific time, or the mass flow of that component over a defined time period, to a defined accuracy suitable for metal balancing. As such, it is the first measurement in the chain that includes sampling, sample preparation and analysis, each of which introduces its own errors. Materials often contain moisture, the proportion of which must also be established in order to obtain the dry mass. They may also have to be measured as a volume or mass/mass flow of slurry, or in stockpiles or storage areas, in which case the relative density must be measured. Both the density and moisture measurement often introduce significant error. Whereas a great deal of effort has been directed at sampling, sample preparation and analysis to improve accuracy and establish the error, the same can seldom be said for the mass determination, including the moisture and density measurements. The possible major causes of error are highlighted and methods of reducing them discussed. Mass measurement can be classified into those measurements necessary for custody transfer and primary accounting of the input and output streams to a plant or operation, and measurements required for secondary accounting, or management control. The latter include intra company transfers and plant area performance, and those required for plant control only. This paper is concerned only with primary accounting measurements. The code and best practice state that the equipment should be certified (as sized) as is required for custody transfer. The most accurate and precise of the various possible methods is the static measurement of mass on a weighbridge, platform scale or a weigh bin. If static measurement is not possible, which is often the case for ore fed to a plant, possible alternatives are electromechanical conveyor belt weighers or in-motion weighing of rail trucks. In all cases the material must be adequately sampled to enable a representative moisture content to be determined to calculate the dry mass. Where material is flowing inside conduits, only certain types of the multiplicity of flow meters available may be used and, in the case of slurries, very few flow meters are suitable. As most flow meters measure volume or velocity, the density of the material must also be measured. The basic requirements in order to achieve satisfactory results for the mass, of the component of interest, are listed, as well as common problems and pitfalls encountered in practice. The measurement of the mass of stockpiles and in-plant stocks, often required for metal accounting, is often the largest source of error in metal balances. The reasons for this and methods for reducing and managing the effect are discussed.

Jan 1, 2009

By B. Mulcahy, M. Valenta

"The purpose of executing a project in a stagewise fashion is to evaluate all potential options in a cost-effective manner and develop an understanding of the project drivers, thereby minimizing overall project risk to the client. Among the more valuable tools for this exercise are production and financial models that can be used to quantify the sensitivity of the project to the critical parameters.The mine and concentrator used in this case study are located on the Kalahari Copper Belt, which extends from Zambia through northern Botswana into Namibia. This area of Africa has seen very little industrial development and the project will create much-needed employment and development in the region.The success of this project thus far can be attributed to the close cooperation between the geological, mining, and metallurgical disciplines. Regular updates of projected capital and operating cost estimates coupled with project outputs guided the teams in optimizing their various discipline models, ultimately delivering a compelling argument for the execution of the project. Key to the success was the development of a geometallurgical model for the prediction of concentrate tonnage, grade, and recovery for the life of the mine from the mining plan.This paper summarizes the metallurgical findings and the outcome of the various project stages. The development of the model is discussed, as are the challenges faced in developing a suitable metallurgical process route. IntroductionThe Kalahari Copper BeltThe Kalahari Copperbelt, which extends from Zambia across northwest Botswana into Namibia, is considered to be a broad time equivalent of the Central African Copperbelt, with a similar style of mineralization. However, at shallower depths (<25 m), chrysocolla and malachite exist in significant proportions in certain geological areas. As illustrated in Figure 1, the project is located in the Ghanzi-Chobe Fold Belt which forms part of the Kalahari Copper Belt. The Ghanzi Group, which overlies the lowest stratigraphic unit (the Kwebe Formation), consists of three formations, namely the Ngwako Pan, the D’Kar, and the Mamuno Formation (Hall, 2012)."

Jan 1, 2016

By L. Lorig

"Two types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudo-static analyses. The acceptance criteria are often promulgated by governments despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems than earthquakes. Two types of problem are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare. This paper will discuss the mechanisms for rainfall-induced slope instability, as well as analysis methods. Examples will be discussed and analysis methods are proposed. IntroductionTwo types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudostatic analyses. The acceptance criteria are often promulgated by governments (e.g., Peru, Chile) despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems when compared to earthquakes. Two types of problems are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare, but do exist. In Peru, for example, slopes are required by law to be designed for a 100-year storm."

Jan 1, 2016

By P. J. Petit

Changing mining conditions, legislative issues, rising costs, and the constrained supply of skills and electricity in South Africa, have been some of the criteria forcing mine operators and engineers to review the traditional use of compressed air to power underground hand-held drilling operations in narrow-stope, hard-rock mines. In answering the question, &apos;What is the best way to power this mine?&apos;, they have resorted to trade-off studies with results of limited usefulness, because they are site-specific, and use only a few comparative parameters, based on a small data set. This paper aims to provide definitive, objective and quantitative decision-making approaches to evaluate alternative energy delivery systems for stoping in narrow-reef hard rock mines, based on primary and relevant criteria. These include quantifiable criteria such as capital expenditure, operating costs, resulting financial returns, energy and water usage, production performance, life-of-mine, etc. Other important criteria with qualitative aspects are integrated. These are safety, health and environmental concerns, legislative requirements, business risk, technology change, etc. The paper begins with a review of decision making processes available, and proposes the use of the analytical hierarchy process (AHP) method as a multiple-criteria decision making tool and the decision tree-based on milestone-driven uncertainties, to validate the selection of the energy delivery system. The results of a multiple-criteria questionnaire completed by a variety of industry experts and professionals, such as production and operation managers, consultants, suppliers and techno-financial analysts, are discussed. The evaluation indicates the potential for hydropower to be the best solution for narrow reef hard rock mines, based on current information, mine design layout and production.

Jan 1, 2012

COUNCIL FOR 1990/91 President H.G. Mosenthal President Elect RD. Beck Senior J.P. Hoffman Vice Presidents Junior Or H. Scott-Russell Immediate Past President Or O.K.H. Steffen Honorary Treasurer OrH. Wagner

Jan 1, 1991

By M. Timucin

High-temperature phase relations and thermodynamics of the condensed phase region of the Pb-S-O system at 1473 K were analysed by use of the available information. The sub-regular solution models on Pb-PbS and PbO-PbSO4 continuous melts were used in conjunction to generate a consistent set of thermodynamic and phase equilibrium conditions for the Pb-S-O system. The directions and distributions of conjugation lines between melts of this system were derived with relevant activity and composition data. The calculations permitted the thermodynamic analysis of direct lead smelting and the construction of isothermal reaction diagrams for the system in terms of oxygen and sulphur partial pressures at 1473 K.

Jan 1, 1989

By P. J. D. Lloyd

The Federation of Societies of Professional Engineers (FSPE) recently conducted a survey of professional engineering manpower in South Africa. This article presents the data relevant to mining and metallurgical engineering. FSPE in their survey attempted to determine the supply of engineers in South Africa both from local universities and by immigration. The immigrants gave some problems in that it is difficult to know whether a man who claims to be professionally qualified really is. However, it was estimated that the ratio of immigrants who claimed to be qualified to those who really are the equivalent of our local graduates was between 1,0 and 1,9 for mining engineers, and between 2,0 and 4,1 for metallurgical engineers.

Jan 1, 1980

Copper cyanide is a common component of cyanide-treatable precious metal ores. The copper concentration in production heaps can be predicted from laboratory column tests, but the exact correlation is not necessarily intuitive. Generally, heap leach operators like to keep copper concentrations in solution below 300?500 ppm and may note problems with gold recovery and cyanide consumption when copper concentrations exceed this amount. There are several methods of copper removal from cyanide solutions including ion exchange; direct electrowinning; acidification, volatilization, and recovery (AVR); and sulphide precipitation such as the sulphidization, acidification, recycling, and thickening (SART) process. SART involves acidification with addition of soluble sulphide, separation of the resulting copper sulphide precipitate, and addition of lime to re-establish alkalinity prior to returning the solution to the leaching process, recovering both copper and cyanide as valuable products. In principle SART is very simple. Yet some SART plants that have been built may have been unnecessarily complex. This paper explores the basics of SART and makes the case for a simple plant design as applied to the heap leaching circuit.

Jan 1, 2012

By J. A. L. Napier

An essential requirement for the planning of the global capacity of a mine is a knowledge of the functional relationship between the production level and the capital expenditure necessary to establish that level. An underlying mechanism connecting capital expenditure and mine production capacity is proposed in terms of a characteristic profile of the expenditure that both precedes and succeeds production expansion. By the assignment of a representative shape to this profile, the capital expenditure of individual mines can be modelled. The empirical values describing the characteristic profile are computed for a number of gold mines, and an attempt is made to explain variations in the model coefficients from mine to mine in terms of physical parameters such as shaft depth, shaft concentration, and average rate of depth increase during the life of the mine.

Jan 1, 1981