Search Documents

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publication Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis. Index, only if paper is long and involved. Introduction, including a brief statement of conclusion. Development of the main substance. Conclusions, in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systemé International d'Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organisations as well as to the Institute.

By G. Sommer, R. P. Chaix, G. T. W. Ormrod

Recent developments in the instrumentation and automation of uranium-processing plants by G. SOMMER, Ing. (Grad.) (Visitor), G. T. W. ORMROD (Visitor), and R. P. CHAIX, B.Sc. (Visitor) The paper discusses work at the National Institute for Metallurgy on the evaluation of measuring techniques for the automatic control of free acid in leaching. of the ratio of ferric to ferrous ion in leaching, of pH in liquid-liquid extraction. and of uranium in loaded solvent. Commercially available instruments. and the modifications that have been made to adapt them to South African uranium plants, are also described.

By E. J. Y., G. J. McLachlan, E. Amini, Koha

Inferring individual component flotation rates from recovery-time data of ore complexes is important in optimising and designing minerals processing plants. However, existing two-component first-order flotation models are computationally intensive to solve using conventional non-linear least squares regression. In this paper, a Convolutional Neural Network (CNN) is used to approximate the inverse function which predicts the two-component first-order model parameters using recovery-time data. This paper compares the accuracy and computation speed of the proposed CNN against traditional non-linear least squares regression on 1 million generated data based on a known two-component firstorder kinetic model. It is shown that using a CNN is possible to approximate the inverse function for the non-invertible two-component model with recovery-time as an input matrix for convolution operations. The CNN method is 450 times faster to compute than the Trust-Region (TR) non-linear least squares regression algorithm. However, the CNN model is less accurate compared to the TR algorithm overall. Keywords: Flotation kinetics, convolutional neural network, inverse problem, modelling and simulations

Jan 1, 2020

By I. J. Geldenhuys

South Africa’s mining and metals industries have an illustrious history dating back to the Late Iron Age. We live in a complex and data-intensive world that has already fundamentally changed how we work and live. The outbreak of the global COVID-19 pandemic in 2020 resulted in immeasurable suffering worldwide, but the crisis also accelerated many technological developments and altered the way we think about, and experience, technology and work. Problem-solving requires new and rapidly changing skills to manage the data tsunami. Whether at the rock face or on the processing plant, the fundamentals have not changed, although how we interact with minerals and their properties has changed dramatically. Sustainable processing and design are non-negotiable if we genuinely want to achieve the aim of the cradle-to-cradle principle. As we venture forth, what can scientists, engineers, technologists, and mathematicians learn from history? History is data presented in a context; sometimes, the context is also important. We exist in an age of data, with most of the world’s data created in only the past two years. History can enhance our understanding of the present and enhance our future outcomes. Lessons from history can help provide insights into making ethical and sustainable choices related to technology or engineering in the mining and metallurgical industry. Shifting the perspective of mining and metallurgy professionals from a narrow focus on complex technical solutions towards a broader context for problem-solving and designs that includes the entire ecosystem is crucial. In other words, using or reflecting on historical process development is, at its core, systems thinking.

Sep 1, 2021

By K. G. Lomberg, M. D. Lionnet

The Bafokeng Rasimone Platinum Mine (BRPM) is a joint venture between Rustenburg Platinum Mines Limited and Royal Bafokeng Resources (Pty) Ltd (Bafokeng). The mining lease has been granted over Boschkoppie 104JQ and is located approximately 10km south of the Pilanesberg Alkaline Complex. The Merensky Reef, which constitutes the principal ore body, is geologically complex. A relationship between its geological variability and the associated mineralisation has been established by defining a number of facies types. The Merensky Reef has been sub-divided into seven distinct facies types: the pegmatoidal facies, contact facies, FW1 pothole facies, FW3pothole facies, FW6 pothole facies, and FW7 pothole facies. The Merensky Reef, which does not form part of the potholed reef, has a large component of footwall mineralisation. The pothole facies, in contrast, has mineralisation located in the hangingwall. Statistical analysis of the facies types indicates that they are unique populations and hence need to be evaluated independently. The mining lease has distinct structural domains that have added additional complications to evaluation of the Merensky Reef. The Merensky facies on BRPM exhibit unique geological and statistical characteristics within well-defined structural blocks. Due to the extreme variability of the Merensky Reef on BRPM a unique approach has been developed, within Anglo Platinum, to evaluate the deposit. Mining cuts are defined and composited for the individual facies types, and then modelled individually by applying known geological controls. The resultant grade models are weighted based on statistical and local geological knowledge. The object of weighting the facies is to replicate the variability observed in the ore body. The introduction of stringent geological controls to the evaluation process has resulted in increased confidence in the in situgrades estimated as an input to the mine planning process

Jan 1, 2006

By V. K. Risinggård, M. Sparta

We report on the development of a finite-element method model for a pilot furnace for the production of manganese alloys. The model is a multiphysics model that addresses material flow, electrical conditions, heat transfer, and physical and chemical transformations. It is capable of studying both quasi-steady and transient states in time-dependent simulations. The model includes common charge materials and fluxes and can simulate production of both ferromanganese and silicomanganese alloys with acid and basic slags, as well as changing charge compositions. The model output provides access to the material distribution in the furnace during furnace runs, temperature profiles, current paths, energy balances, and alloy and slag production rates and compositions.

Apr 16, 2024

By I. C. R. Gilchrist

A principal requirement in the design of a backfill transportation pipeline is the accurate prediction of the values of key slurry flow parameters. Input variables, such as particle size and solids concentration, are usually determined by the load-bearing requirements of the placed fill. It is therefore necessary to identify the optimum conditions of transport for a particular combination of input variables. This paper critically reviews the methods available to predict the values of flow parameters in slurry pipeline systems in the light of experimental data generated at a test facility. Particular reference is made to rod milled waste and deslimed tailings transport systems and, in the case of the former, it is shown that both pumping and load-bearing requirements can be optimized.

Jan 1, 1988

By P. Muthaphuli

Kumba Iron Ore?s Zandrivierspoort (ZRP) magnetite-haematite project aims to mine and beneficiate a magnetite resource with low contaminant levels to produce from 1 Mt/a to 2.5 Mt/a product, which will be either a concentrate, micro-pellets for direct reduction, or blast furnace pellets. Anglo American Technical Solutions Research conducted a number of piloting campaigns to validate the process design flow sheet, demonstrate process performance, and to generate data for use as a design basis. Secondary to this, the pilot plant was to produce approximately 7 t of magnetite-haematite concentrate with low enough SiO2 to be used as feedstock for pelletizing studies. The pilot plant achieved 34.2% mass yield, at 69.0% Fe, 2.2% SiO2, from an IsaMill grind of 80% -45 µm. This product quality will compare favourably to other leading direct reduction (DR) pelletizing concentrates. However, two-stage comminution to 80% -75 µm and beneficiation of ZRP ore will produce a blast furnace (BF) quality pelletizing concentrate, indicative quality being 67.6% Fe and 4% SiO2, at higher mass yields. An economic evaluation between producing a DR and a BF pelletizing concentrate will have to be conducted prior to finalizing the concentrate production flow sheet..

Jan 1, 2014

By S. M. Spottiswoode, A. J. Jager, N. C. Gay, J. A. Ryder

The South African mining industry is at present planning to extract orebodies at depths of up to 4 km. To do this cost effectively and, at the same time, ensure safe working conditions for mining, the personnel will require both the development of new strategies and the implementation of current rock-engineering technological developments on a wide scale. This paper covers most of the technological developments likely to be required for mining at very high stresses, but it is clear that improved regional support systems will need to be developed to ensure defective stability of the rockmass during mining operations. Similarly, it is clear that improved strategies for mining in large-scale geologically disturbed areas, where slip on faults or dykes can result in wide-spread rockburst damage, will have to be addressed

Jan 1, 1995

By K. C. Corin, M. Tadie, R. M. Manenzhe

The near depletion of high-grade ores, among other factors, has necessitated the consideration of alternative PGM sources. Various factors in the metallurgical processing of ores result in valuable minerals being lost to the tailings, and hence, PGM tailings are a possible alternative PGM source. However, as the value residing in PGM tailings remains unquantified and uncharacterised, there is a challenge in knowing the recoverable fraction of value contained in PGM wastes. This paper outlines the in-situ techniques of oxygen uptake and EDTA extraction for their possible use for determining the recoverable value in PGM tailings. Both methods have shown efficiency in determining the weathering of sulphide minerals and sulphide-bearing ores. Keywords: PGM tailings, tailing retreatment, oxidation, oxygen decay, EDTA

Jan 1, 2020

By A. C. Lawrence, K. F. Mauer

Human factors in stope productivity -a field experiment by K. F. MAUER, M.A. (Visitor), and A. C. LAWRENCE, B.Econ., D.Com. (Member) An experiment in which three human variables were manipulated in eight stopes was conducted in a gold mine over a period of roughly six months. The three variables, which each had two levels, concerned the degree of movement from gangs, the quality of the Bantu production supervisors, and the extent to which gangs were composed of a single ethnic group (Malawians). Time was included as a variable with three levels in the analysis of the findings. On the average, stable gangs produced 12 per cent more than gangs with a high percentage of transfers, gangs with better production supervisors were more successful by nearly 9 per cent than those with poorer production supervisors, and homogeneous gangs were more productive than heterogeneous ones by as much as 15 per cent. In addition, it was found that a number of the variables exercised a joint influence on stope productivity and that the effects of the variables were accentuated by the len gth of time they had been in operation. V

Jan 10, 1973

By N. Naude, W. P. Roux

Fine particle beneficiation plays an ever-increasing role in mineral processing plants and it seems that technology can’t keep up with the challenges involved in the treating of these fines. The REFLUX™ classifier has proven itself able to treat high tonnages of fine material, especially in the coal industry. There are various fine ore applications that can benefit from such a process, yet laboratory and pilot-scale tests on many of these ores show poor efficiencies and recoveries. A better understanding of the design, operation and mechanisms of the REFLUX™ classifier is required to determine if and how it fits into these applications. The mechanisms in gravity separators are very complex due to the complex hydrodynamics, and the REFLUX™ classifier is no exception. The mechanisms of these systems are usually described through theoretical single particle-models that are hard to verify through analysing the feeds and products of these processes. To verify these models the movement of individual particles must be measured, which is not an easy task. In this paper the separation mechanisms in the incline channels of the REFLUX™ classifier were investigated with high-speed videography. A small lab scale model of the incline channel was constructed for this purpose. It was possible to capture and track the trajectories of particles under certain conditions and match these trajectories with theoretical models. The resuspension of particles, clustering and streaking was also observed and captured. Keywords: REFLUX™ classifier, particle trajectory, beneficiation, high-speed videography

Jan 1, 2020

By L. Kühnel, H. Lieberwirth

Confined bed comminution in High Pressure Grinding Rollers (HPGR) and Vertical Roller Mills (VRM) is gaining substantial attention in many applications. Previously used mainly for milling coal or construction materials, HPGR and VRM have started to complement or even replace tumbling mills in ore beneficiation. Materials like coal or clinker are relatively homogenous, however, in comparison to metal ores and wall rocks. This characteristic poses a new challenge to the confined bed comminution but also an opportunity. Fuerstenau and Abouzeid have investigated the selectivity in comminution of a mixture of particles of different strength in a particle bed. The median particle size and particle size distribution (PSD) of the two constituents used were kept constant. Only the proportion of the two constituents was modified. The competence of a material is, however, also a function of particle size. Smaller particles tend to be more competent than larger ones of the same material. If selective comminution is applied on ores, this size influence has to be understood. The paper presents research results on this topic based on experimental investigations with model materials as well as with natural particles, which were stressed in a piston-die press. It appeared that the comminution result depends substantially on the material characteristics and the composition of the mixture. Conclusions will be drawn for the application in future applications of selective comminution in mineral processing. Keywords: Confined bed comminution, HPGR, VRM, piston die press, particle size

Jan 1, 2020

By P. L. Moolman

An approach to the design of a tailings disposal system is presented using an example from a platinum project on the eastern limb of the Bushveld Complex as a base case. The design is driven by two inputs: namely, maximizing water recovery and minimizing power cost, expressed as cubic metres and kilowatts per ton of solids deposited on the tailings storage facility respectively. The approach considers low-, medium-, and high-density platinum tailings and uses material-specific aspects such as thickening and rheology to determine the most economical option. An analysis based on direct capital and operating cost (water and electricity) shows that the medium-density scenario results in the lowest total cost per ton of tailings deposited, even though this system results in the highest electricity consumption per ton of tailings deposited. As the cost of water and electricity is likely to increase in the future, the higher-density tailings disposal options become more economical, with the paste option the preferred option.

Jan 1, 2012

By S. M. Rupprecht

"Artisanal mining is basic mining characterized by manually intensive work methods utilizing primitive or simple equipment and conducted by individuals or small groups exploiting deposits. Artisanal mining in Rwanda and Burundi is further complicated in that the techniques applied are often inadequate, resulting in low productivity and poor recoveries, and workers are paid low wages with owners reluctant to reinvest in the mining operations. A consequence of this vicious circle is often poor working conditions, with miners operating under unsafe and/or unhealthy working conditions. An additional problem is that mining is conducted in a manner that is detrimental to the environment.Artisanal mining is commonly more dangerous than large-scale modern mining operations. Artisanal operations are generally subsistence activities with the miners focusing more on immediate concerns than the long-term consequences of their activities. When miners have no other source of income, they will usually find ways to evade controls and carry on working. Machinery tends to be expensive and often far beyond the reach of most artisanal miners, and therefore there is a general tendency for workers to focus on labour intensive and riskier mining methods.This paper proposes the introduction of small-scale mechanization with labour-intensive manual mining utilizing a bench mining approach in artisanal mines operating in Central Africa. From the 1950s to the 1980s bench mining was successfully conducted in Burundi utilizing manual labour. In order to achieve a balance between job creation and project economics, the combination of manual and mechanized mining is proposed. Manual mining offers the benefit of local job creation while ensuring good mining techniques, such as minimizing mining loses and dilution. Through the introduction of mechanized loading and hauling activities, areas of high stripping ratios can be viably mined, thus increasing the amount of resources that can be exploited. The use of a loader and tractor-trailer arrangement is proposed, thereby improving throughput, productivity, and worker safety and, reducing the impact on the environment."

Jan 1, 2017

By J. Pelders, F. Magweregwede, S. M. Rupprecht

Increased depths of conventional gold and platinum mines, longer travelling times as working places move further from the shaft, and ancillary activities taking place in the mining cycle reduce the useable time spent at them workface. Current shift lengths of 8 hours 20 minutes may no longer be adequate ton complete required mining activities.The impact of mineworker commuting times on shift work is also not well understood. The aim of this research was to draft a framework to optimize shift cycles in order to maximize productivity, health, safety, and wellness in the South African mining sector. The framework was informed by a review of the literature, case studies at a local gold mine and platinum mine, and a workshop with industry experts. The findings indicate potential advantages of extended shift lengths and continuous operations, such as improved productivity, asset utilization, and employee morale. However, concerns included fatigue and the associated safety hazards, particularly when working longer shifts, night shifts, and numerous consecutive shifts. Job demands, personal factors, and commuting times are further considerations when scheduling shifts. The ideal shift system for the mining sector should holistically consider and balance operational requirements, health and safety, and employees’ and their families’ requirements, and suit the unique needs of each operation. Changes in shift cycles will require a structured change management process, which involves all stakeholders, and could help to enhance the viability of the South African mining sector.

Aug 1, 2021

By Y. Qin, L. Han, P. Gao, Y. Han, Y. Lia

In the present study, an innovative comminution technology of high-voltage pulse discharge was proposed for galena to weaken the mechanical property. The results of pre-treatment experiments indicated that the optimal operating conditions of spherical gap spacing 25 mm, pulse numbers 120, and loading voltage 25 kV were obtained, where the relative grindability of pretreated products was improved significantly, although with the prolonging of grinding time, the superiority of high-voltage electric pulses was gradually weakened. The galena ores were subjected to a high-voltage pulse discharge, and then the crack generating along the boundary between galena and gangue was observed under an optical microscope, and the surface burning which appeared in the ores. The scanning electron microscope (SEM) results indicated that the pretreated products were in a state of melting and then condensation, accompanied by some pore formation. Pulsed discharge pre-treatment not only produced more micro-cracks and cracks in the sample but also extended the original crack. Keywords: High-voltage pulse discharge; galena; relative grindability; micro-crack

Jan 1, 2020

By M. G. Maruma, L. A. Mampuru

"Mill liner wear is a major cost item in the mining industry and there is continuous research to prolong the life of the liners. Over the years it has become apparent that even though high-chromium white cast irons are highly efficient as abrasion-resistant materials, a combination of wear resistance and fracture strength remains difficult to achieve. Increasing the hardness of the high-chrome white cast iron (HCWCI), which improves the resistance to abrasion wear, is often accompanied by a deterioration in fracture strength. Operational conditions inside the mill require that the liner should be made of highly wear-resistant material with some fracture strength. Vanadium additions ranging from 0.2 to 3 wt% were made to HCWCI in an attempt to refine the microstructure. It was found that an increase in vanadium content promotes grain refinement. A content of 1.5-3 wt% gave the best results as measured by the maximum breaking strength.IntroductionOver the years it has become apparent that even though high-chromium white cast irons are highly efficient abrasion-resistant material, a combination of excellent wear resistance and fracture strength remains difficult to achieve. The exceptional wear resistance of highchromium white cast iron (HCWCI) is attributed to hard chromium carbides embedded in an austenitic/martensitic/pearlitic matrix. When the chromium contents exceed 12 wt%, interconnected MC3-type carbides of conventional cast irons are replaced by rodshaped and isolated M7C3 carbides (Powell, 1980), leading to an improvement in the impact toughness, ductility and fatigue resistance. However, the main M7C3 carbides in HCWCI are hard and brittle and can provide an easy path for crack propagation. This limits the applications of HCWCI, particularly in severe impact conditions. Most operations involving HCWCI are in crushing and grinding and the life of a part/liner is limited by its wear resistance. However, improving the wear resistance of HWCI comes at the cost of a significant reduction in fracture strength. Concerns about premature failure of HCWCI mill liners in the mining industries prompted a study to improve the wear resistance and mechanical properties of HCWCI."

Jan 1, 2016

By T. Nghipulile, M. Moys, M. Bwalya, H. Simonsen

The quest for efficiency in comminution is an ongoing concern as comminution usually constitutes a major cost component in the metal production industry. Such improvements can be made by circuit optimization or development of more efficient equipment. A novel crusher, known as the rotary offset crusher (ROC), promises to deliver in this space. The ROC was invented in 2002 by Michael Hunt, Henry Simonsen, and Ian Sinclair, but failed to garner enough support to progress to production. The original design concept was recently rekindled, and a laboratory version of the crusher has been built and commissioned at the University of the Witwatersrand. The crusher is simple in design, with two cylindrical discs that are parallel to each other, and, as the name implies, there is an offset between the vertical axes of the discs. The top disc has a conical section on its lower face, and this creates a crushing zone between the opposite faces of the two spinning discs. Centrifugal motion transports particles through the crushing zone. Batch experiments have been conducted with quartz at various crusher settings (discs offset, rotational speed, and vertical exit gap) for various feed size distributions. The indications so far suggest that the disc speed is a key factor affecting the performance. Size reduction ratios as high as 11 were recorded from experiments with quartz at a speed of 830 r/min.

Jan 1, 2021

By E. Y. Baafi, H. Fan, W. Zeng

We present a discrete event simulator, TSJSim (Truck-Shovel JaamSim Simulator), for evaluating the stochastic and dynamic operational variables in a truck-shovel system. TSJSim offers four truck allocation strategies: Fixed truck assignment (FTA), Minimizing shovel production requirement (MSPR), Minimizing truck waiting time (MTWT), and Minimizing truck semi-cycle time (MTSCT) including the genetic algorithm (GA) optimization and the frozen dispatching algorithm (FDA) optimization rules. Multiple decision points along the haul routes for all the trucks close to the decision points were included in the model. The simulation results indicate that the trends associated with production tons and queuing time utilizing the four truck allocation strategies (MSPR, MTWT, FDA, and GA) all demonstrated similar patterns as the fleet size varied. As the system fleet size increased, the system production tons under these strategies at first increased significantly and then remained relatively constant; the queuing time relating to these strategies showed a positive relationship with the system fleet size. The bunching time decreased when the truck allocation strategies were applied in the model. In the simulated truck-shovel network system with multiple traffic intersections, by assigning the trucks at the intersections, both productivity and fleet utilization increased.

Dec 13, 2022