Search Documents

By P. T. Slatter

The role of viscometers for rheological characterization in the hydraulic transport of solids is discussed, and rheological models and phenomena pertinent to the hydraulic transport of backfill material are reviewed. The two main branches of viscometry (rotational and tube) for the measurement of mining slimes rheology are compared. The effects of solids concentration, particle size and chemical additives and the practical application of rheology in backfill system design are presented.

Jan 1, 1988

By R. Xie, J. Liu, Y. Zhu, Y. Li

The surface chemistry features of spodumene and feldspar were investigated by XPS, zeta potential measurements and first principle calculation. The results indicated that the zeta potential of feldspar was more negative than that of spodumene. The most possible active sites on spodumene and feldspar were Al sites and O sites. However, the number, type and activity of these sites were different. The flotation behaviour of five new collectors (cationic collector decyloxy-propyl-amine (DPA), anionic collector α-bromododecanoic acid (α-BDDA), N-Dodecyliminodiacetic acid (DIDA), and mixed collector DPA-BDDA and DPA-DIDA) were investigated through micro flotation experiments and analysed based on the surface chemistry features of spodumene and feldspar. The results revealed that cationic collector DPA processed a high collecting capacity for both minerals. The highest recovery of spodumene and feldspar was 91.60% and 95.30% respectively. The anionic collector α-BDDA and DIDA showed poor flotation behaviour. The recovery of spodumene and feldspar when using α-BDDA as collector was less than 5% and when using DIDA as collector was less than 1%. For the mixed collector DPA-BDDA, the recovery of spodumene and feldspar was 82.27% and 32.61% respectively at pH 4.5. For mixed collector DPA-DIDA, the recovery of spodumene and feldspar was 35.69% and 9.08% respectively at pH 5.8. The results indicated that the cationic collector had high collecting capacity, but low selectivity. The collecting capacity of anionic collector for spodumene and feldspar was poor at the same concentration compared with cationic collectors. Mixed collector DPA-BDDA showed good flotation behaviour and selectivity on spodumene. The ―COO- in mixed collector might improve the selectivity. However, too much ―COO- would increase the electrostatic repulsion, which might cause low selectively and poor recovery. Keywords: Spodumene, feldspar, surface chemistry features, mixed collector, flotation

Jan 1, 2020

By C. Birch, J. Perold

"Due to the challenging geological environment of the Postmasburg Manganese Field (PMF), a study was conducted to determine if any benefits would derive from the inclusion of resistivity data during threedimensional (3D) modelling of the manganese resource. This was achieved by estimating manganese resources from 2011/2012 drilling data and comparing them with manganese resources estimated from the same drilling data and resistivity data collected during 2013 and 2017.Both models were adjusted to limit their extent to the same 3D modelling space. Significant volume and tonnage differences were observed for all lithological units. The greatest differences were noted in the manganiferous zones of alteration – 7.200 Mt for the geological model versus 3.700 Mt for the geoelectric model.This study showed that the inclusion of resistivity data can reduce exploration costs significantly, as a direct consequence of the resistivity data allowing more accurate siting of boreholes. This decreases the number of boreholes, samples, and analyses required due to the 3D electrical delineation of mineralized areas prior to drilling.An additional benefit is the ability to more correctly forecast the net present value of an operation due to more accurate estimation of manganese resources and stripping ratios. This is clearly demonstrated by the estimated gross profit estimation of R409 million for the geological resource model versus R264 million for the geoelectric resource model.The addition of resistivity data can, therefore, reduce exploration costs and can increase confidence in geological and financial modelling. It would be reasonable to conclude that this approach could also be used for karsthosted massive sulphide deposits. IntroductionAccording to Corathers (2014) and Gajigo, Mutambatsere. and Adjei (2011), South Africa holds between 75–80% of global manganese reserves, followed by Ukraine (10%), Australia (3%), India (3%), and Gabon (2%). The known, land-based, manganese resources located elsewhere are estimated at 2%.The majority of economically important sedimentary manganese ore deposits in South Africa are situated in the Northern Cape Province (Gutzmer, 1996). Manganese ores of the Postmasburg Manganese Field (PMF) were discovered in 1922, and the Kalahari Manganese Field (KMF) in 1940. According to Astrup and Tsikos (1998) and Gutzmer (1996), mining of manganese ore from the PMF ceased during 1989 in favour of the superior quality of manganese ore from the KMF."

Mar 1, 2019

By D. H. Batchelor

Efficient modern-day mining operations are turning increasingly to technology to combat rising operating costs in an adverse economic climate for the industry. Computerised truck dispatching is one such technological advance that has enhanced the efficiency of the mining operation at Palabora. The economic incentives, basic operation and general system benefits of Palabora's computerised truck dispatching system are considered.

Jan 1, 1987

By M. Faure

The experiment with backfill at Harmony was mainly an attempt to improve the ground conditions in a particularly tricky section of the mine. A deslimed tailings system was selected for financial reasons, ease of installation, ease of operation and its low level of mechanization. The design of the system has three aspects: firstly, to define the parameters of the backfill material itself; secondly, to design a reliable plant which could consistently produce the desired material in sufficient quantities; and, thirdly, to design a fill distribution system for maximum reliability in the shaft, minimum pipe line velocity, pressure and cost in the horizontal sections and consistency and reliability at the delivery end. The system was successfully constructed and commissioned in a short space of time at a relatively low cost. It has now reached its full potential, and very encouraging results have been achieved with regard to cost savings, ground conditions, ventilation and accident statistics.

Jan 1, 1988

By Kedikilwe Oageng

Effective perimeter control during drilling and blasting is critical not only to blasting results but also to the overall stability of the pit over its entire life span. A pit where perimeter control is not given enough attention when conducting drilling and blasting operations, often experiences over-break or back break beyond final pit wall limits, and therefore has a relatively high probability of failure. Such a pit also becomes unsafe, sometimes not easily accessible, has increased loading costs due to production of oversize, longer cycle times and often problems are encountered when blasting subsequent benches. All these are undesirable consequences, which have negative cost implications. Specialised blasting techniques such as trim blasting and pre-splitting have over the years proved to be effective perimeter control measures. However, the success of these techniques is directly attributable to the time and effort given to the processes. This paper presents results of a project undertaken to monitor, review and optimize the trim blasting and pre-splitting processes at Orapa Diamond Mine in Botswana. The project was specifically incepted to improve the final wall conditions, which continued to deteriorate due to persistent over-break during blasting. The paper also analyses the results obtained against a benchmark of results taken prior to project implementation. Specific blast design parameters which are critical to blasting results were identified as problem areas after auditing of the pre-implementation drilling and blasting practices. These include drill-hole depth, spacing, splitting factor for pre-splits and timing of trim blasts. The impact of different rock types on the results was also studied, and recommendations were made at different phases of the project and results obtained after implementation analysed until optimum results were achieved.

Jan 1, 2008

By S. O. Bada

Coal is a complex mixture of organic and mineral constituents and is the most abundant resource of fossil energy in the world. In recent years, significant research into dry coal beneficiation has gained much attention, primarily due to the need to improve grades and reduce the environmental contaminants in coal without the use of water, and to achieve this in as cost-effective manner as possible, relative to wet beneficiation processes. This paper seeks to review the application of various electrostatic separators with their process principles, to draw comparisons between different dry beneficiation techniques with specific emphasis on the tribo-electrostatic separation method, and finally to report the results of tribo electrostatic separation conducted on various South African coals. Previous research conducted on Indian, European and American coals has indicated that this technique is likely to lead to significant economic benefit through the reduction of ash content, NOx and more specifically Sox by separating out the liberated Fe-S-bearing minerals prior to utilization. The removal of the latter suite of minerals is also likely to significantly reduce or eliminate the emissions of associated trace elements, including mercury and arsenic. The research results reported in this paper indicate that the rotary tribo-electrostatic process has the potential for significant upgrading of high ash pulverized South African coal. The impact of various operational parameters was investigated and key factors established for the optimum recovery of low ash and low sulphur fine coal.

Jan 1, 2010

By M. A. Belokrys, F. O. Milovich, D. D. Aksenova, V. A. Ignatkina, V. A. Bocharov, A. A. Kayumov

Copper remains one of the most sought-after metals in the industry. Tennantite (Cu12As4S13) and tetrahedrite (Cu12Sb4S13) that occur in pyrite copper, copper-zinc and polymetallic ores are an additional reserve for increasing technological parameters of flotation. Pyrite mass (85% and more) has similar flotation properties to other sulfide minerals, and imperfection of reagent regime is a common problem that occurs during quality copper concentrate processing. Due to tennantite's and chalcopyrite's differences in flotation properties with butyl xanthate at pH > 10, tennantite often reports to the flotation tails. Hight alkalinity of the medium increases the oxidation level of sulfide minerals, thus increasing the concentration of S2O3 2-, SO3 2- SO4 2-. At processing facilities in the Russian Federation, the concentration of thiosulfate ions in pulp is in the range of 0.5 to 1.5 g/l and higher, which leads to a decrease in flotation activity of the tennantite. The effect of butyl xanthate (as standard), thionocarbamate, dithiophosphate and M-TF (a mixture of dithiophosphate and thionocarbamate) on monomineral (tennantite and pyrite) flotation in the presence of sodium thiosulfate was studied. The variable parameters of the "thiosulfate-collector" flotation complex were thiosulfate concentration (100-900); pH (8-12,5). The scientific methods included contact angle for hydration assessment; TEM for surface studies; UV spectroscopy and iodometric titration for solubility control. Comprehensive studies have established a connection between the concentration of thiosulfate ions and tennantite flotation selectivity. Flotation activity of tennantite is higher at pH 8 with a thiosulfate concentration under 300 mg/l. Pyrite remains active with butyl xanthate under the same conditions. TEM images of the surface films of the collectors on pyrite were acquired at pH 8. The MTF provides the biggest difference in adsorption, wettability and flotation activity between tennantite and pyrite at pH 8 and thiosulfate concentration under 300 mg/l, in comparison with butyl xanthate. The results of the research will be applied to improve selective reagent regimes of tennantite minerals flotation. Keywords: Tennantite, pyrite, chalcopyrite, sphalerite, flotation, sulfhydryl collectors, thiosulfate, adsorption, mechanism, reagent regime

Jan 1, 2020

By W. Ferreira

Steel is produced in a basic oxygen furnace from hot metal obtained from a blast furnace. A sintered iron ore with good hightemperature properties (strength and permeability) should be used as feed to the blast furnace. The quality of this sintered ore depends on the reactivity of the iron ore used as feed to the sinter plant during the lime assimilation step in the sintering process. The penetration test is the standard method for evaluating the reactivity of iron ore with lime. It is, however, difficult to determine the exact depth of penetration from the standard test. A new test method is proposed that allows automatic evaluation of iron ores in terms of lime assimilation with increasing temperature. A comparison of the coefficients of variation for the new and standard methods for each ore type demonstrates that the results of the new test are more reproducible and more precise than those of the standard method. The test is also less time-consuming and easier to implement.

Jan 1, 2014

By M. Gao

The Zinifex Century Mine employs a large number of Detritor mills for fine and ultra-fine grinding to liberate silica and sphalerite at 80 per cent passing 7.5 microns before final zinc flotation. A joint project between CSIRO Minerals and the Zinifex Century Mine was carried out to evaluate the Detritor mill performance. Plant surveys were conducted around the Detritors in conjunction with laboratory tests. The survey data showed that the Detritors in the ultra-fine milling circuit performed well. They reduced a feed F80 sizing of 46 microns to a product P80 sizing of 7.5 microns at a gross energy consumption of 37.2 kWh/t. Scale-up of ultra-fine milling Detritors was studied using a 0.55 kW laboratory batch unit and a 355 kW full-scale Detritor by processing Century zinc concentrate with 1 mm sand media. The results indicated that the 0.55 kW laboratory mill underestimated the energy consumption of the full-scale Detritor by about 20 per cent for a product P80 of seven microns. The performances of a horizontal IsaMill and a vertical Detritor were compared as ultra-fine milling devices for processing Century zinc concentrate. The experimental data demonstrated that, when using the same grinding media, the energy efficiency of the two mills is similar despite the difference in mill designs. The Detritors used for regrind duty at the Century Mine performed poorly when processing feed at 80 per cent passing 88 micron. The energy consumption was high and the product size distribution was broad with particles above 100 microns in the feed unbroken and particles below ten microns overground. A coarser ceramic media of 3 mm was therefore tested in a laboratory Detritor to process the regrind Detritor feed as an alternative to the 1 mm Colorado sand used at the Century Mine. The ceramic media reduced the energy consumption significantly and produced a narrower product size distribution, which is more desirable for the downstream flotation process.

Jan 1, 2007

Exxaro installed their first ultra fines treatment plant at Leeuwpan Coal mine. The plant is now fully operational and results already show that the plant has great potential. The plant was designed and installed by DRA. Several challenges were faced during the installation due to the space constraints in the Leeuwpan plant. Efficiency tests were conducted on both modules after commissioning and showed very promising results. A lower ash product with a higher yield can be produced with the fine coal dense medium cyclones compared to the spirals previously employed.

Jan 1, 2010

By B. Zlender

ABSTRACT: The paper presents investigation of carboniferous slates from the Trojane hilly area performed on series of samples of equal material. The results of static loading tests show that carboniferous slate is heterogeneous and yields on slate layers. Where that kind of heterogeneity is distinctive the strength results are essentially lower of commonly tests results. The results of dynamical loading tests show that the slate surfaces have the essential meaning for the stability of the material. When those surfaces are moistened the material become unstable. RÉSUMÉ: L'article présente une épreuve des ardoises carbonifères de la région montagneuse de Trojane sur une série des échantillons des matériaux identiques. Les résultats des tests de charge statique montrent que l'ardoise carbonifère est hétérogène et qu'elle cède sur les couches d'ardoise. Quand l'hétérogénéité est distinctive, les résultats de stabilité sont essentiellement plus bas que les résultats obtenus par des tests ordinaires. Les résultats des tests de charge cyclique montrent que les surfaces d'ardoise sont très importantes pour la stabilité du matériel. Quand ces surfaces sont mouillés, le matériel devient instabile. ZUSAMMENFASSUNG: Der Artikel präsentiert die Forschung von Karbonschiefersteinen im Bereich des Bergland Trojane, ausgeführt durch Serien von Proben aus den gleichen Erdmaterial. Die Resultate der statischen Belastungsprüfungen zeigen, das die Karbonschiefersteine heterogen sind und die Schieferflächen nachlassen. Wo bei dieser Art der Heterogenität die Festigkeitsergebnisse wesentlich niedriger sind als bei gewöhnlichen Testergebnissen. Die Ergebnisse der zyklischen Belastungsprüfungen zeigen das die Schieferflächen eine wesentliche Bedeutung für die Stabilität des Erdmaterials haben. Wen diese Schieferflächen befeuchtet sind, wird das Erdmaterial unstabil.

Jan 1, 2003

By Thomas V. Fame, William E. Porter

"As geological and mining conditions become more complex, and as overall mining economics become more marginal, short- and long-range decision-making regarding multiple-seam surface mining becomes more difficult. The decision-making problem involves a study of economics, cut-off grades and ratios, equipment capabilities, sequencing and selective mining practices.This paper is concerned primarily with multiple-seam mining of bituminous coal. The research has led to the development of an economic decision-making model for use as a day-to-day tool to aid mine operators and pit geologists to decide what and how to mine.The model is designed as an aid for feasibility decision-making in multiple-scam situations and for situations where selective mining is needed or desired. In effect, a simulation of the feasibility and preliminary mine planning phases has been developed. The model is divided into four separate segments: decision-making, simulated mining, cost calculations and the determination of the discounted cash flow return on investment."

Jan 1, 2014

By C. Musingwini, A. S. Nhleko, P. M. Muke

Open-pit mine planning includes the determination of a long-term open-pit mine production scheduling (OMPS) plan. The OMPS plan is generally a three-dimensional (3D) block extraction sequence that seeks to maximise the net present value (NPV) of future cash flows, while complying with technical and operational constraints. The OMPS problem is computationally complex because it involves the analysis of large datasets, while simultaneously incorporating both multiple hard and soft constraints. The OMPS problem has been solved using deterministic or exact approaches, heuristic, and metaheuristic models. When compared to heuristic and metaheuristic models, deterministic approaches tend to take much longer to solve the OMPS problem when the number of constraints increases. Therefore, this paper presents a metaheuristic model which utilises a genetic algorithm (GA) framework to solve the OMPS problem. The GA-based model was applied to the Newman1 and Zuck Small mining instances, which are publicly available from the online MineLib database. The NPVs for the OMPS plan generated using the GA-based model for the two case studies were compared to the best-known published MineLib solutions obtained using the TopoSort heuristic model at the time of this study. For the Newman1 instance the equivalent annual NPVs were approximately US$6.6 million for the GA-based solution and US$5.1 million for the TopoSort solution. For the Zuck Small mining instance, the equivalent annual NPVs were approximately US$99.8 million for the GA-based solution and US$102.5 mil for the TopoSort solution. These results show that the GA-based model produced comparable solutions to some of the best-known solutions, thus, indicating strong potential application of GA-based models to solve OMPS problems.

Sep 1, 2021

By S. Govender, J. J. L. du Plessis, R. C. W. Webber-Youngman

Spontaneous combustion (SC) is a cold oxidation reaction that generates heat, causing a temperature rise of the reactant and leading, with limited heat dissipation, to self-ignition of the reactant, which occurs without an external heat source. Although not limited to coal, the most significant hazard of SC are the fires that occur in coal mining operations around the world. These fires pose a serious risk to the safety of workers in the mines as well as adverse effects on the environment, and can affect the quality of life for current and future generations. We investigated the occurrence of SC in raw coal storage bunkers with the purpose of compiling a decision analyser for engineers designing or working with coal storage bunkers. Specific experts were interviewed from different backgrounds and companies, followed by field research at a coal mine. The important factors affecting the possibility of SC occurring were the type of coal supplied to the bunker, the mining practice, and physical conditions around the bunker. The information presented here will assist in reducing the SC risk in raw coal storage bunkers. These findings, together with the systematic decision analyser developed, will assist design engineers and mine personnel to take early preventative steps in managing SC. The decision analyser was tested for many different scenarios and gave good guidance on how to minimize and prevent SC in bunkers

May 1, 2021

By N. J. Roodt

Mine dumps created in terms of the pre-MPRDA regime (old order mine dumps) are currently not regulated by the MPRDA, and the common law owners of such dumps are free to process them without the need to obtain the relevant rights. The MPRDA Amendment Act purports to change this position. However, the wording of the Amendment Act raises a number of problems which render the post-amendment position at best unclear and at worst absurd and unworkable. The primary concern with the Amendment Act is that, on one interpretation, material placed on the same dump at different times may be treated differently at law. Thus, parts of a dump may be subject to one person?s right while others may be subject to another?s right. Moreover, case law has generally regarded mine dumps as movable property and, by extending the MPRDA to apply to all mine dumps, the Legislature is extending the ambit of the Act to cover movable property, a scenario not contemplated by the wording of the Act (even after its amendment) in relation to applications for rights. The better interpretation of the amendments, which are not yet in force, is that they will not apply retrospectively to old order mine dumps.

Jan 1, 2010

By E. van Steen, G. M. Leteba

Optimizing the catalytic performance of multimetallic nanoparticle (NP) catalysts demands a concrete understanding of their design, while preferentially deploying wet chemical synthesis procedures to precisely control surface structural properties. Here we report the influence of reductants such as hydrogen-rich tetrabutylammonium borohydride (TBAB) and carbon monoxide-rich molybdenum carbonyl (Mo(CO)6) on the shape and morphological evolution of Pt-based binary (PtNi and PtCo) and ternary (PtNiAu and PtCoAu) nanostructures derived from a homogeneous solution of aminebased surface active agents (surfactants) in a high boiling point solvent. We successfully synthesized nanostructures exhibiting well-defined and composition-controlled surfaces deploying a one-pot synthetic approach. The development of the surface properties was, however, observed to be alloyspecific. The resultant highly monodisperse alloy NP with narrow size distributions and facet-oriented surfaces are expected to display enhanced functionality as catalysts for utilization in specific chemical reactions.

Jun 1, 2021

By L. Linzer, J. Oelofse, T. Rangasamy

Extraction of isolated blocks of ground with elevated levels of stress and/or seismicity is a common occurrence in South African gold mines. Isolated blocks of ground that are divorced from the main orebody and are bound by complex, dip and strike parallel, non-persistent geological structures dominate the Klerksdorp gold fields. No quantifiable methods exist to assess the risk associated with mining these and other classes of remnants. A case history, from a gold mine that planned to extract three remnant blocks hosted in a large complex fault system, is used to illustrate the decision making process based on a combination of underground observations, numerical and seismic techniques. Simple risk estimation matrices were developed and used to estimate remnant-mining risk and finally to quantify the decision on which of the three remnant blocks could be extracted at the lowest possible geo-mechanical risk. Il est courant dans les mines aurifères sud-africaines d’extraire des blocs de terrain isolés qui possèdent des niveaux élevés de contraintes et/ou sismicité. Les régions aurifères de Klerksdorp sont dominées par des blocs de terrain isolés qui sont séparés du gisement principal et qui sont retenus par des structures géologiques non continues, à parallèle de pendage et direction, et complexes. Il n’existe pas de méthodes quantifiables pour évaluer le risque associé à l’extraction de ce genre et autres genres de résidus. Une observation de cas, celle d’une mine d’or qui avait l’intention d’extraire trois blocs de résidus qui se trouvaient dans un grand système complexe de faille, est utilisée pour illustrer le processus décisionnel basé sur une combinaison d’observations souterraines, et de techniques numériques et sismiques. Des matrices simples d’estimation de risque furent développées et utilisées pour estimer le risque lié à l’extraction des résidus et finalement pour quantifier la décision sur lequel des trois blocs de résidus pouvait être exploité au moindre risque géo-mécanique. Die Extraktion isolierter Gesteinsblöcke mit erhöhtem Spannugsniveau oder Seismizität ist in südafrikanischen Goldminen üblich. Isolierte Gesteinsblöcke, die von der Haupterzader getrennt und durch komplexe, parallele abfallende und horizontale nicht persistent geologische Strukturen gebunden sind, beherrschen das Klerksdorp Goldfeld. Es gibt keine quantifizierbare Methoden die das Risiko welches mit dem Abbau dieser und anderer Klassen verbunden ist beschreiben. Eine Fallstudie einer Goldmine, welche die Extraktion von drei in einem großem komplexen Verwerfungssystem eingelagerten Einschlußblöcken plante, wird verwendet um den Entscheidungsprozeß zu illustrieren, der auf einer Kombination von Untertag Beobachtungen und numerischen und seismischen Techniken basiert. Einfache Gefahreinschätzungsmatrizen wurden entwickelt und angewendet um das Abbaurestrisiko abzuschätzen und letztendlich die Entscheidung zu quantifizieren, welcher der drei Einschlußblöcke unter dem niedrigst möglichen geo-mechanischen Risiko extrahiert werden konnte .

Jan 1, 2003

By D. Sethuram, P. G. Koppad, S. Iyengar, R. Shobha

TiB2 and CeO2 particle-reinforced Al6061 hybrid composites were manufactured using stir casting and hot rolling techniques. The base alloy and composites were hot-rolled at 500ºC and a 50% reduction was achieved through 12 passes. The effect of varying TiB2 and CeO2 particle additions on the microstructure and mechanical properties of the Al6061 matrix was studied. Scanning electron microscopy showed uniform dispersion of both the reinforcements, with good interfacial bonding. Microhardness and tensile properties like yield and tensile strength were found to be higher for hybrid composite with 2.5% TiB2 and 2.5% CeO2 compared to Al6061 alloy and other hybrid composites. The increased tensile strength is attributed to good dispersion and interfacial bonding between the particles and Al6061 matrix. Fracture analysis using a scanning electron microscope revealed ductile fracture for the Al6061 alloy and mixed characteristics of ductile-brittle fracture for hybrid composites

Oct 1, 2021

By Xiang-nan Zhu, Hao Zhang, Lin Li, Jun Qiu, Yue-xian Yu, Chun-chen Nie, Xian-jun Lyua

Waste printed circuit boards (WPCBs) are excellent metal resources. Mineralogical characteristics of different components in WPCBs were analysed in this study. Organic-enriched particles, fibreglass-enriched particles, associated particles and metal-enriched particles were obtained by density gradient method. Subsequently, the elemental composition, morphology, dissociation characteristics, functional group composition and phase composition of different components were analysed by X-ray fluorescence spectrometer (XRF), scanning electron microscopy and energy dispersive spectrometer (SEM+EDS), infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). Elemental analysis results show that Cu is mainly contained in metal-enriched particles. SEM+EDS analysis results demonstrate that ideal dissociation can be achieved when the WPCBs are broken to -1 mm. Organic matter particles are enriched with carbon and oxygen elements, while fibreglass particles and associated particles mainly contain Al and Si elements, verified by XRD analysis. FT-IR results show that hydrophilic and hydrophobic groups exist widely in all components, caused by widespread organic matter. This study reveals the important properties of different components in WPCBs, which is of great significance for the subsequent separation process. Key words: Waste printed circuit boards, mineralogical analysis, elemental composition, dissociation; phase analysis, functional group composition

Jan 1, 2020