Search Documents

By M. C. Chapman, E. C. Westman, A. T. Iannacchione

Examination of seismic records during the time interval of the Sago Mine disaster in 2006 revealed a small amplitude signal possibly associated with an event in the mine. More needs to be understood about the seismicity from mine explosions in order to properly interpret critical seismic information. A seismic monitoring system located at NIOSH’s Lake Lynn Experimental Mine has monitored experimental gas and dust based explosions and impact tests. The seismic signatures from these different events were analyzed using standard waveform analysis procedures. The magnitude of seismic energy during a gas and dust explosion was found to be more dependent on mine entry geometry and seal behavior rather than on the amount of explosive fuel present. The results suggest a large explosion that’s not restricted can generate potentially the same magnitude as a small explosion that is restricted.

By K. O. Bennington

The thermodynamic properties of pollucite [(Cs0.650Na0.185Rb0.028)(AlSi2) (05.8630H0.137)?0.19H201 were determined by the Bureau of Mines in collaboration with the Argonne National Laboratory. The standard enthalpy of formation determined by hydrofluoric acid calorimetry is ?Hf°298 = -3,098.52 ±3.63 kJ mol-1. The standard enthalpy of formation from the oxides is ?H298 (from oxides) = -209.50 ±2.38 kJ mol-1. Low-temperature heat capacities were determined by adiabatic calorimetry from 5.0 to 306.1 K. The derived standard entropy is S°298 = 207.24 ±0.43 J mol-1k-1. Enthalpy increments above 300 K were measured by copper-block drop calorimetry from 349 to 674 K. Various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation and Gibbs energies of formation are given as functions of temperature. The Gibbs energy of formation is ?Gf°298 = -2,919.9 W mol-1

Jan 1, 1983

Reduce longwall intake contamination by controlling respirable dust generated by the stage loader. Approach Install a water-powered scrubber on the stage loader immediately outby the crusher. Dusty air from the crusher is drawn through the scrubber and a clean air discharge is delivered into the primary face airflow. How It Works The contamination of intake air is a significant dust control problem often overlooked on many longwall faces. This dust source contributes to the full shift dust exposure of all face personnel, and thus can significantly affect compliance with Federal regulations. Several sources contribute to contamination; however, dust generated by the stage loader crusher is the single largest source. The breaking action of the crusher generates a tremendous quantity of dust, which mixes with the primary ventilation airstream and is carried down the entire length of the longwall face. The installation of a water-powered scrubber (see diagram) has proven effective in controlling crusher-generated dust. The scrubber is mounted immediately outby the crusher. A duct is placed over the scrubber intake and attached to a flanged opening over the crusher discharge. In

Jan 1, 1982

By James P. Ulery, Stephen J. Kravits, William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and Beth Energy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from overlying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine's ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the Iongwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 1992

By Stephen W. Lambert, Michael A. Trevits

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

Reduce fire warning time and avoid activation of false alarms in underground mines. Approach A heat activated stench/tracer gas system was developed which automatically releases the gas mixture into the mine ventilation air. How It Works A canister approximately 12 inches long and 3 inches in diameter is charged with 50 grams of ethyl mercaptan or other appropriate stench gas and 500 grams of instrument detectable Freon. The canister is then pressurized to 100 psi with nitrogen. A disc is used to seal the contents of the canister. A low-temperature alloy designed to melt at a predetermined temperature is used to restrain a spring loaded plunger. Upon exposure to heat, the alloy melts and the plunger is released. The plunger ruptures the disc and the mixture of stench and tracer gas is released from the canister. Canisters are mounted in areas of a mine which are susceptible to fire such as near

Jan 1, 1983

Minimize airborne respirable quartz dust produced by continous mining machines. Approach Install a shovel-mounted underboom water spray system on the off-curtain side of the mining machine. Dusty air containing quartz is momentarily trapped under the boom, where it is captured by fine spray mist. The remaining dust cloud is directed immediately behind the curtain before it can migrate back to the machine operator's location. How It Works Previous studies have shown that most of the dust generated by continous mining machines occurs under the boon as the cutter head shears down. The primary source of respirable quartz dust on many continous mining operations is cutting or trimming roof rock immediately prior to shearing. This results in very high concentration , of

Jan 1, 1989

Determine the site specific flow behavior of leachants and groundwater during development, production, and restoration phases of an in situ leaching operation. Approach A computer program has been developed which simulates the hydrologic activity associated with in situ mining. Various user options enable modeling of many of the site specific geologic conditions and well field specifications that affect the hydrology of solution mining. How It Works In situ hydrology is modeled, using a closed-form solution to the three-dimensional, partial differential equation that describes changes in hydraulic head as a result of pumping from leachant Injection and recovery wells. Model capabilities include arbitrary well patterns and pumping schedules, partially penetrating well screens, directionally anisotropic permeability and natural groundwater flow, in either

Jan 1, 1981

By Joseph Cervik, J. H. Perkins

The Bureau of Mines has conducted desorption work on fine coal particles at near atmospheric pressure. An apparatus has been developed that uses a capacitance manometer to measure desorption of methane from coal particles up to 2 inches in diameter and pressures up to 1,000 psi. This will make it possible to duplicate the desorption process as it occurs in its natural under- ground environment.

Aug 1, 1970

Use instantaneous sampling to pinpoint dust sources and to Improve dust control on longwalls. Approach Use a dust monitor developed under a Bureau contract. How It Works Sampling can be done by either a moving or a stationary method. In the "moving' method, the dust monitor is carried by a survey engineer walking at the midpoint of the shearer Dust levels and face position (support number) are taken during all phases of the mining cycle while the shearer is cutting. These measurements can show how changes in airflow along the face, face specific; (rock partings) and cutting sequence (cutting the wedge) variables affect dust levels. In the "stationary sampling" method, the survey engineer stands with the RAM at a fixed location on the face. As the shearer approaches, the dust level and the distance to the shearer are recorded at 10-second intervals. Typically measurements start when the shearer is 20 feet from the sampling position and continue as the shearer passes the position until it is 20 feet away on the other side. Dust profiles around the machine are obtained at several fixed locations along the face only while the shearer is cutting.

Jan 1, 1982

By Fred N. Kissell, Maurice Deul, T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

Provide exhaust face ventilation to remotely-controlled continuous mining machines making extended advances without exposing workers to unsupported roof. Approach Modify the sprayfan to move additional air to and from the coal mine face. Unmodified, sprayfans are capable of ventilating the face with 20-foot brattice setbacks. Additional sprays on the rear of the mining machine allow setbacks to be extended up to 40 feet.

Jan 1, 1988

By A. Mayton, A. Brien, W. Porter, O&apos

In 2004, management at Unimin's Gleason, TN operation began implementing ergonomic interventions specifically targeted to reduce risk of musculoskeletal injuries (MSIs). Together with corporate and site management, Unimin identified work site hazards and began to modify work practices/equipment. Some interventions were relatively simple and were implemented immediately. Others, like improvements to a mobile shredder, were more complex but were eventually resolved through a participatory approach with employees, management, manufacturers and NIOSH. This paper discusses ergonomic interventions that were successfully implemented using a bottom-up approach to reducing the risk of injury.

By Francis R. Redfern

Newton's method of solving a nonlinear equation is employed to develop a least-squares acoustic emission source location method in which the spatial residuals of the location equations are minimized. These residuals, related to the distances from the least-squares source location perpendicular to the surfaces described by the location equations, permit location error to be estimated to first order along the spatial axes. The solutions obtained by this method are the best spatial solutions to the location equations in the least-squares sense. Also presented is a procedure by which the geometrical control of a transducer array can be evaluated using the rate of change of source location with fractional velocity change.

Jan 1, 1982

Reduce the noise levels to which operators of double-drum longwall shearers are exposed without compromising the operational effectiveness of the shearer. The Problem Noise produced by double-drum longwall shearers can be harmful to machine operators. Typical noise levels at the lead-drum operator position range from 100 to 105 dBA, and Federal noise regulations allow only one to two hours of exposure per shift at these levels. Noise radiated by the shearer cutting drum is the primary contributor to the overall noise level. However, test of a noise-controlled cutting drum developed by the Bureau of Mines reduced the operator noise level to 95 dBA, thereby increasing the allowable operating time to four hours per shift. Approach The key design aspect of the noise-controlled shearer drum is its reduced vibration-al response to coal-cutting forces. Laboratory studies have shown that these forces are concentrated in the low-frequency region (500 Hz and below). Since the cylindrical core and the cantilevered I plate-like helix of the standard shearer drum are easily excited by these forces (natural vibration frequencies be-

Jan 1, 1985

By Joseph E. Matta

The Bureau of Mines conducted tests using a tracer-gas technique to measure the effectiveness of the jet fan, which is often employed in mines to ventilate dead headings. Results of these tests show that jet fans can (1) ventilate dead headings beyond the maximum penetration distance indicated by smoke-tube detection of air movement, and (2) redistribute available fresh air through larger working areas. However, if the fresh air base is insufficient, the fan will merely recirculate the contaminated air and disperse it over a larger volume.

Jan 1, 1978

Provide an operator cab to assure protection, comfortable use of controls, and good visibility. Approach A cab which raises and lowers by pivoting about d horizontal axis was Installed on two S&S cleanup tractors and tested in two underground working mines. How It Works Hydraulic cylinders actuated by a lever inside the cab cause the cab to pivot about a horizontal axis. This action raises or lowers the cab height. The total cab excursion is 14 inches. A release valve in the hydraulic system allows the cab to lower automatically if struck by a roof load or overhead obstruction. The pivoting action of the cab is engineered so that the operator maintains comfortable use of all controls at all cab heights. The movement is such that the angular relationship of the operator's ankles With the tram and brake foot controls IS consistently within 90 to 100 degrees. Figure 1 outlines the approximate position of the operator at three cab elevations.

Jan 1, 1977

To quickly and reliably assess the stability (safety) of saturated and unsaturated tailings pond embankments. Approach Determine embankment geometry and soil properties, then use that data to obtain the safety factor of the embankment directly from one of a series of factor-of-safety charts.

Jan 1, 1982

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982

Continuously monitor air-borne radon daughters that are a hazard to underground miners. Approach A beta detector continuously counts beta activity collected on a filter paper to allow calculation of exposure in working level units. How It Works At each Site a constant flow pump draws mine air through a fiberglass filter located in front of a beta detector (pancake type Geiger Mueller tube), Radioactive particles (products of the radon 222 gas emanating from the mine walls) collect on the filter and decay, releasing alpha and beta particles as well as gamma rays. A portion of the beta particles penetrate the Geiger tube window and create electrical pulses in the tube. These pulses are then amplified and sent by a coaxial type or shielded electrical cable to a central monitor located some distance from a working level detector. At the central monitor incoming Signals are amplified and fed into two channels, (See the block

Jan 1, 1979