Search Documents

By Harry Dobroski, Larry G. Stolarczyk

A medium-frequency (MF) communication system has been built and has been tested in underground mines. It provides radio coverage to vehicles and personnel anywhere in the mine via parasitic coupling into existing mine conductors. The system consists of base stations, repeaters, and vehicular and personnel transceivers. Air-core antennas for vehicles and clamp-on antennas for base stations and repeaters were designed for maximum coupling efficiency using existing mine wiring. Personnel transceivers are of a unique vest design that features a low physical profile, good user comfort, and efficient antenna design. In-mine tests show impressive results. Range between rubber-tired vehicles and base stations is often measured in miles. With repeaters, greater range is possible.

By W. F. Marshall

The effect of engine parameters on exhaust emissions from two diesel engines was studied experimentally. Fuel-injection characteristics and intake air conditions were considered as parameters influencing the emissions. Emphasis was placed on the effect of parameter variations on nitrogen oxide (NOx) emissions, because diesels generally emit very low levels of carbon monoxide (CO) and unburned hydrocarbons. Emissions other than NOx were at lowest levels when the engines were adjusted for best performance. NOx emissions can be diminished somewhat through variation in fuel-injection characteristics, but there generally are penalties in emissions of CO, smoke, and unburned hydrocarbons or in engine performance. Temperature and composition of intake air have a significant effect on NOx emissions. Levels of NOx are reduced by recirculating the exhaust gas or by adding water to the intake air stream. However, the rate of water added or exhaust gas recirculated must be limited to prevent the degradation of engine performance and increased emissions of CO and smoke. At high exhaust recirculation rates, levels of CO and smoke were increased such that it was necessary to derate the engine and also to use a catalytic system for oxidation of CO.

Jan 1, 1971

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal nonfuel mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1982

By Kenneth C. Stewart

Eight brands (three samples of each kind) of commercially available audio-dosimeters were performance-tested. Each unit was placed in an anechoic chamber and subjected to various acoustic signals to measure its A-weighting response and overall integration accuracy. All units met the A-weighting tolerance for type II sould level meters, and six brands were within the Bureau I s overall accuracy requirements of ±2 dbA referred to input.

Jan 1, 1974

By J. G. Walters

The method for predicting coke strength developed at Steinkohlenberg-bauverein, Germany, in which experimental parameters are readily determined by small-scale laboratory tests, was found to be applicable to cokes produced from industrially used blends of American coals. Predicted 1-inch ASTM tumbler indices for four industrial blends were found to be in excellent agreement with the experimentally determined values. The laboratory determined prediction parameters include the proximate analysis of the coal the size consist of the coal, and Ruhr dilatometer test data.

Jan 1, 1971

By Robert W. Freedman

This report describes sampling and analytical procedures used for measurement of sulfates in diesel tailpipes and in the diluted exhaust within dilution tunnels. A variety of methods exist for sulfate analysis for such systems, including ion exchange. Two chemical methods used by the Bureau of Mines are described in detail. These are based upon spectrophotometric measurement of chloranilic acid using barium chloranilate. The procedures are rapid and relatively inexpensive. In general, ion exchange is preferred by many analysts for sulfate analysis. However, it is more complex and expensive than chloranilic acid procedures, which are adequate for exhaust analysis.

Jan 1, 1982

By J. Douglas Causey

In 1985, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a portion of the 110,000 acre Massacre Rim Wilderness Study Area (CA-020-1013). The area studied, containing 23,260 acres, is located in northwest Washoe County, Nevada, about 25 miles west of Vya adjoining the Charles Sheldon National Wildlife Refuge. Basalt caps older tuffaceous sedimentary rocks in an area that contains no claims or prospects. No mineral resources were identified during this investigation.

Jan 1, 1987

By J. M. Harrington, C. W. Owings

"The transportation of explosives, and especially their distribution from the supply magazines of the manufacturers or dealers to the mines, quarries, or other points where they are to be used, by means of horse-drawn vehicles is an old-time practice, and the records of accidents of the past show this to have been a hazardous undertaking requiring for safety the taking of many precautions not required in the transportation of other merchandise.Displacement of the horse-drawn vehicle by the motor vehicle for the transportation of explosives is increasing rapidly. A consideration of the facts that the vehicle is operated by an explosion engine, using easily vaporized liquid fuel; that the charges in the engine are fired and the vehicle lighted by electricity; and that the vehicle, being operated insulated from the ground, may accumulate static charges led to the conclusion that new hazards are being introduced into the transportation of explosives through the use of motor-operate& vehicles, and that therefore additional special precautions must be taken against these additional hazards.That accidents have already occurred in this use of motor-vehicle transportation is evidenced from the following examples:Recently in California a driver loaded a box of granular powder in the rear of an automobile truck and a box of electric detonators in the front. Suddenly, while traveling along a highway, the explosives detonated, demolished the truck, and blew the body of the driver into small pieces. No evidence was left to show the cause of the explosion, but it is assumed that a jar or other means caused the detonators to fire, and that they in turn detonated the explosive. It should be recognized that it is unsafe to transport detonators and explosives in the same compartment, and this rule should be strictly enforced. At present this rule appears to be either unknown or, at least, frequently ignored.There are usually so many possible causes of ignition or detonation of a truck load of explosives that it is often impossible to state definitely the exact cause in a given case. This is well illustrated in the following account of an accident: A trucking company was hired to haul a truck load of explosives about 200 miles. The driver had had experience in driving trucks of explosives, and it was stated that he inspected the truck carefully before leaving the garage. Eighty 50-pound boxes of explosive were placed in tiers on each side of the truck and 265 25-pound kegs of black blasting powder were placed in the center of the truck. The boxes were placed flat and the kegs were placed on end, arranged in tiers. While the truck was being driven along the highway there was a muffled explosion. When some men, who were about a quarter of a mile away, arrived at the scene the truck was in flames and they could get no nearer than 100 feet. The driver was sitting in his seat and had apparently been killed instantly either by shock or fumes. When the flames were finally quenched, the driver's body was recovered, badly charred. It was, found that several boxes of explosives had been thrown about 40 feet by the initial explosion but were uninjured. A total of half a ton of dynamite was recovered. The cover to the gasoline tank could not be found."

Aug 1, 1930

By George M. Lucich

This report describes a sensitive, proportional temperature controller developed by the Bureau of Mines that is useful in the temperature range from 40 to 400° C with an accuracy of ±0.10 C. A temperature controller of this kind is potentially useful for regulating temperatures in air chambers, liquid baths, furnaces, and reaction vessels, and for other applications. This instrument was developed to control the duration and temperature of the heating cycle of a charcoal-filled adsorber that is part of a special helium analyzer used by the Bureau. The controller was made from commercially available parts, and can be easily modified to provide continuous temperature control. The circuit is solid state and employs no electromechanical devices. Over a 2-year period of use as a component of the special helium analyzer, this temperature controller performed successfully and required no maintenance.

Jan 1, 1979

By Daniel Edelstein

In 1985, ASARCO Incorporated terminated copper smelting operations and associated byproduct arsenic trioxide recovery at Tacoma, WA, although shipments of arsenic trioxide from stocks and limited production from cleanup operations continued. Imports of arsenic trioxide increased markedly as a result of increased demand for arsenical wood preservatives and the decline in domestic shipments of trioxide. Expanded world capacity more than met the increased demand for arsenic and its compounds, and prices remained unchanged throughout the year. Domestic Data Coverage.-Arsenic trioxide was produced by one U.S. company, which voluntarily reported its production to the Bureau of Mines.

Jan 1, 1987

By Frank J. Susko

The U.S. Bureau of Mines is developing a process for removing metals from mining and mineral processing waste streams by precipitation. The precipitation process is accelerated by flocculation when a high molecular weight polymer is added. Infrared (IR) studies were performed on zinc hydroxide [Zn(OH);J, copper hydroxide [Cu(OH);J, and zinc sulfide (ZnS) flocculated with both non ionic and anionic polyacrylamide (PAM) and polyethylene oxide (PEO). The IR data were compared with general trends in the performance of the polymers observed during flocculation. These studies will help to understand the bonding between the precipitate and polymer and indicate the effectiveness of a flocculant for dewatering. Two types of bands showed up on the IR spectra; one type described the interlayer water of the flocs, the other described the organic bonds of the polymers. A general decrease in the areas of the three water bands, hydroxyl (O-H) stretching (3,200-3,500 cm-1), water bending (1,610-1,630 cm-1), and torsional oscillations (600-700 cm-1), indicate interlayer water being driven off, which is a favorable condition in flocculation. Shifts in the O-H stretching band indicate water bridging between the precipitate and polymer. Shifts in the amine (N-H) deformation, carbon-nitrogen (C-N) stretch band (1,600-1,610 cm-1) indicate the amine group of the PAM is involved in the bonding. Evidence suggests that ether oxygen of PEO is also involved in the bonding process.

Jan 1, 1990

By Jack C. White

The Bureau of Mines, in its efforts to insure the continued viability of the domestic minerals economy, has been engaged for several years in research on the extraction of alumina from domestic, nonbauxitic resources. Hydrochloric acid leaching of kaolin is one of the more promising technologies being studied for recovering alumina for feedstock to existing aluminum smelting capacity; 93 pct of this feedstock is currently imported either as bauxite or alumina. Organics contamination of pregnant leach liquor, originating during solvent extraction for removal of iron from aluminum chloride solution formed during hydrochloric acid leaching, causes rapid deterioration of the semihard rubber lining of process equipment. These organics were removed by a skimming tank-coalescer-activated carbon adsorption system. Organic levels of less than 10 ppm from the coalescer and less than 0.5 ppm from carbon adsorption were achieved. Analytical methods employing CC14 extraction and infrared spectrophotometry were developed to determine the organic content of both the liquor and the carbon. Mass transfer zones delineated in the carbon columns provide adsorption data for the design of larger systems.

Jan 1, 1981

By Manuel Gomez

Prediction models were constructed for seam elevation, overburden, and sodium concentration for a lignite deposit in Ward County; N. Dak. These models were developed by mathematical-statistical techniques using surface coordinates as independent variables to permit interpolation between drill holes. The results suggest that sodium concentration in lignite may be predicted in advance of mining. This information is helpful to mine planning, specifically, in scheduling production to deliver a uniform product to existing powerplants.

Jan 1, 1970

Provide an instrument for continuous remote monitoring of carbon monoxide concentration in underground mines. Approach A carbon monoxide fixed? point continuous monitor consists of two modules. A line-powered control module is designed to power a remote transducer module; provide continuous readouts, visual and audible alarms, operational checks; and activate fans and equipment shutdown circuits if preset CO concentration levels are exceeded. How It Works The control module must be used in conjunction with a single transducer module. Developed under contract. the control module is a wall-mounted Instrument which contains a readout and alarm capability and power supply

Jan 1, 1981

By Edward A. Mihok

This paper presents plant design and cost estimates for limestone treatment of acid mine water covering a wide range of quality and quantity conditions. The treatment process consists of limestone neutralization, aeration, solids settling, and concentration. The design criteria for the various operation functions are based on pilot plant performance, laboratory data, and established mine water treatment standards. Unit costs have been assumed and are related to general market prices and conditions. These estimates serve as preliminary indicators of what it would cost to construct and operate a mine water treatment plant.

Jan 1, 1970

By Richard Hammer

Various alternating current (ac) methods can localize faults in mining power cables. Several methods considered by the Bureau of Mines in this report are the Murray loop for short circuits, wherein a bridge provides proportional distance to the fault; capacitance measurements for open conductors; inductance measurements for shorted conductors; phase comparison, high speed recordings of voltage and current in the faulted state are compared with normal voltage and current with the difference being a function of impedance change and impedance change being a function of fault location; and standing wave measurements, detecting the resonance of the length of cable to a fault (either short or open). Portable capacitance bridges are presently available for the second method, and the fourth method is well developed for use on large power distribution systems. Because it utilizes pulses rather than ac, the time domain reflectometer (TDR) method of fault locating was not included in this investigation. However, a comparative evaluation between this versatile method and the Murray loop might prove advantageous in locating high resistance faults.

Jan 1, 1977

By W. H. Lewis

This Bureau of Mines report and its companion report (Information Circular 9074) have been prepared as a complete reference on underground coal mine lighting. This report discusses the fundamentals of light and its interrelationship with the visual process. The purpose of the report is to insure an understanding of the numerous complex and interrelated factors that must be considered to design and implement a mine lighting system that will satisfy human needs for good vision and comfort. Topics include history, objectives, and technical considerations of coal mine lighting; light physics; light and vision relationships; and disability and discomfort glare.

Jan 1, 1986

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

By D. Litton, H. Dobroski, J. G. Kovac

Since 1910, the U.S. Bureau of Mines (USBM) has investigated practical ways of dealing with the consequences of major fires and explosions in underground mines. The results of this research have had a significant positive impact on the mining community by enhancing mine workers’ chances of surviving an underground mine disaster. Today, the Bureau continues to conduct research in mine disaster mitigation. Much of this work has direct application to search and rescue situations, such as: emergency evacuation through smoke-filled or otherwise unbreathable atmospheres, locating and rescuing survivors from rubble piles, and fire fighting in confined spaces. Three USBM research areas are discussed: (1) Life Support -- This effort is directed toward research into and development of closed-circuit breathing apparatus for use in hazardous environments which are likely to be encountered in the aftermath of a mine disaster. (2) Trapped Miner Location -- A mine disaster may result in the entrapment of miners whose normal escape routes are cut-off. This research activity resulted in the development of transportable seismic technology that can be used to locate trapped miners. (3) Mine Fire Diagnostics -- This research involves developing practical techniques for remotely monitoring how the atmosphere inside a mine changes during a fire, in order to estimate the spread and severity of an underground fire. This information is critical in deciding how best to fight a mine fire, or whether it is safe to mount a rescue and recovery mission.

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may he measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1989