Search Documents

By M. L. Davis

The principal causes of many methane-gas explosions that have occurred in anthracite mines, especially in thick pitching veins, during recent years can be traced to lack of a satisfactory method of testing for such gas in areas adjacent to those in which blasting is to be done or other sources of ignition introduced. As coal-mine officials and inspectors are required to make examinations for methane in all accessible open workings, including high places, and permissible flame safety lamps have been used almost universally for making these examinations, considerable difficulty has been experienced in proper testing of atmospheres at elevations beyond the normal reach of the examiner, and resultant explosions have often indicated perfunctory tests. The accepted practice of testing for gas in voids or high places generally consists of raising a flame safety lamp, suspended from the end of a long drill, stick, or pipe, into the atmosphere to be tested. Disadvantages noted are: Action of the flame within the lamp cannot be seen readily when the lamp is more then 18 inches overhead, the flame will not be extinguished when less than about 4-1/2 percent of methane is present, and indications of small percentages of methane within the lamp may disappear entirely while the lamp is being lowered slowly to view; the examiner must usually be exposed unnecessarily to falling material; and the lamp may fall and be broken. Thus, the need for a more reliable, safe method of testing for gas in out-of-reach places is apparent. Several electrical methane detectors, tested and approved by the Bureau of Mines, have been used satisfactorily, though infrequently, for making the aforementioned gas tests. Some of these detectors employ a rubber aspirator bulb and rubber tubing of suitable length to draw the atmosphere from high places through and over energized parts of the detector. However, the original expense, susceptibility to damage, and awkwardness of tarrying these instruments in steep-pitch workings has precluded their general use in everyday examinations. Although not as efficient as the electrical detector for determining small percentages of methane or as reliable because of the limitations imposed by oxygen-deficient atmospheres, the modern per¬missible flame safety lamp can, it is believed, be used safely with the rubber aspirator bulb and tubing to greater advantage and with comparative reliability in testing for gas in out-of-reach places. Slight reference to this method of introducing air into a safety lamp is made in a Bureau of Mines publication of l921,2/ and it is quite possible that the method has been utilized in some manner by individuals in American mines during the intervening years. A similar method was used in connection with a nonpermissible Wolf flame safety lamp in at least one coal mine in Japan before World War II. A major change in the construction of this lamp would bar its approval by the Bureau of Mines. An American adaptation of the Wolf lamp, developed

Jan 1, 1954

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

By L. D. Stewart

The main reasons for developing an induction system for signaling from the cage are, first, to increase safety, and second, to effect economies in the operation of cage and ship hoists, especially when work is being done in the shaft. To-day nearly all mines which employ safe methods have installed safety gates on cages, at the different levels, and at the collar of the shaft. Under the old system in some instances signals could only be Given from the station outside the cage, and in other cases, after the signal was given the only method whereby those riding on the cage could control its movements consisted of pulling the bell-rope hanging in the shaft, an uncertain and somewhat hazardous procedure at best. With the system herein described, however, it is possible, without opening the gates, to signal to the engineer from any place in the shaft whether or not the cage is moving, and finder the same conditions it is possible to converse with the engineer by using the telephone. In short, the cage tender has at all times an opportunity either to signal or talk to the engineer without leaving the cage.

Jan 1, 1931

By Paul Hughes

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining has been employed successfully in mines throughout North America as a method of mitigating exposure to the operator having to work under a seismically active ?back?. This paper reviews design methodology in the placement and analysis of sill mats with reference to site observation coupled with on going numerical and analytically derived solutions.

Jan 1, 2006

By Connie S. Musulin

The Bureau of Mines conducted an experiment at Exxon Mineral Co.'s Buffalo Shaft Operation to determine the time required for radon concentrations to return to a base average after fan shutdowns. Shutdown times ranging from 5 min to 16 hr were evaluated. An equation was derived to calculate a ratio that determines the time required for the radon concentration to return to the average level that existed in the mine prior to shutdown. For fan shutdowns of 15 min or more, underground personnel should be evacuated to areas with natural downcast ventilation. For shutdowns of less than 1 hr, personnel should not return to the working area until the elapsed time is four times the shutdown, or until the working area is resampled and found safe. If the mine is not in production during weekends, the downcast fans can be turned off .from midnight Friday until 4 p.m. Sunday, and the radon daughter concentration should be below 1 WL throughout the mine by the start of the shift Monday. This fan shutdown would conserve energy and save the mining company an estimated $21,000 each year.

Jan 1, 1982

By R. R. Brandenthaler

A series of open-flow tests was conducted in the Chickasha gas field, Grady County, Oklahoma, during June, 1927, under the direction of the U. S. Bureau of Mines and at the request of the Oklahoma Corporation Commission. The purpose of these teats was to determine whether or not any differences existed in the open-flow volume of a gas well when taken through well-head nipples of different diameters, and further, to establish if possible a relationship between open-flow volumes taken through well-head nipples of various diameters. The open flow of a well is the volume or quantity of gas, measured under standard conditions, that a well will produce when open to the atmosphere. There are several methods used for determining the open flow of wells; some of the methods are more suitable under certain conditions than others. The Pitot tube method is the simplest, is applicable to almost any condition, and is the one most commonly used. In the tests described in this paper no attempt was made to compare the Pitot tube method with the minute pressure measurement method or the orifice measurement method.5

Jan 1, 1928

By Joseph Grumer

In addition to nine powder and gaseous extinguishants of propagating Pittsburgh seam coal dust-air explosions earlier evaluated,6 10 other powders have similarly been evaluated under like conditions such that wall quenching of the coal dust-air flames was virtually absent and the dust concentration was temporally and spatially uniform to within about ±5 percent. None of the newly examined extinguishants was better than Purple-K (potassium bicarbonate); the 10 of this report are anhydrite (calcium sulfate), monobasic (4 types) and dibasic ammonium phosphate, natural and synthetic cryolite (sodium fluoalumi-nate), sodium sulfate, and tricalcium phosphate. Except for anhydrite, sodium sulfate, tricalcium phosphate, and the cryolites, these materials were about equally effective, when present in relatively low concentrations (weight-percent of the coal dust-extinguishant mixture). The maximum oxygen concentration for the extinguishment of otherwise uninhibited coal dust explosions and the influence of coal dust particle size and the volatile content of the coal were also explored. For the present, the choice of the inhibitor among the good ones evaluated is not as critical as the system to be used to deploy the extinguishant against a coal dust explosion.

Jan 1, 1973

By F. S. Crawford

Mining companies are usually held responsible for accidents occurring to the public around their operations . Safeguards are provided by progressive mining companies to prevent the public from getting into danger from wandering unattended about the properties . At abandoned operations , where little or no supervision can be maintained , persons are often injured through the negligence of the operator in leaving the property in unsafe condition . After a mine is abandoned or a lease is given up by a mining company , the responsibility for the safety of the property rests sometimes with the State to which the property ownership reverts or with the owner of the land ; either is usually quite unwilling to spend any money to remedy unsafe conditions due to the carelessness of the mining company . The land owner or the State , or both , should see that the work of leaving safe conditions behind is done by the operator before he abandons the mine or gives up the lease . Some of the worst hazards to the public at abandoned mines are from old test pits , abandoned shafts or tunnels , open pits , caved ground , and bodies of water in abandoned open pits . Hazards exist from some of these sources during the active operation of a mining property as well . In the early stages of mining operations test shafts are often sunk from 50 to 100 feet deep through the more or less loose material overlying bed rock . When these shafts are left unprotected , they are a serious danger for many years to come . In the course of time they become largely concealed by brush and grass , and thus are a deadfall to anyone who might happen to step into them . This condition will hold true for any part of the country, but to a much less degree where it is not necessary to sink through a great amount of cover . Many progressive operating companies have adopted the practice of filling in test pits after securing the information desired . Some nonresident landowners and exploration companies , however , have left such pits open , and it is extremely difficult for the mine inspector to get into communication with the owner . Frequently operating companies voluntarily fill test pits on adjacent property not

Jul 1, 1930

By Ray J. Holmquist

"INTRODUCTION The Elk Mountain mica deposit was examined in June 1943 by the Bureau of Mines. An exploratory project and an access road for the property were recommended, provided the zinc was put in operation under competent management. K. Garard obtained a lease on the properly and started operations in June 1944; this was followed immediately by the Bureau's exploratory work. Road construction was begun by the Forest Service in July the same year.The lessee mined mica from the richest exposure with a crew of three men for 2-1/2 months. His operation terminated late in September, but the Bureau of Mines project and the Forest Service road construction continued until snow forced suspension of activity during the first week of November.The Bureau of Mines work consisted of trenching with a bulldozer, hand excavating on undeveloped outcrops, extending an existing adit, and starting a new adit below the older workings."

Jul 1, 1946

By C. C. Merrill

Columbium, tantalum, titanium, and zirconium are present in solid waste products generated by the chlorination of rutile used for production of titanium tetrachloride (TiC14). The columbium and tantalum were separated from titanium and zirconium by liquid-liquid extraction techniques using a secondary amine. Salts of these elements are in a leach liquor produced by water leaching of mineral waste from the chlorination of rutile. This waste, produced at the rate of approximately 50,000 tons per year, is about 40 wt pct water soluble. Leach liquors, separated by filtration, were further separated into a solid fraction and a liquid fraction by pressure hydrolysis, The solid fraction containing Cb, Ta, Ti, and Zr was dissolved in HC1-HF and used as a feed solution. Columbium and tantalum were removed from the organic extractant with 1 [N] HC1. A miniature 10-stage reactor showed that the columbium and tantalum present in solution could be separated with a continuous flow.

Jan 1, 1972

By P. J. Dallimore

The Bureau of Mines has calculated general time-dependent solutions for radon diffusion from cylindrical and slab rock samples containing uniform radium distribution. Results have been obtained for several sets of boundary conditions. The method is suitable for determining the effective diffusion coefficient and the effective porosity for radon.

Jan 1, 1983

By Liming Yuan

Three-dimensional computational fluid dynamics (CFD) modeling is conducted to simulate spontaneous heating in a large-scale coal chamber with a forced ventilation system. Spontaneous heating is modeled as the low-temperature oxidation of coal using kinetic data obtained from previous laboratory-scale spontaneous heating studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. The water vapor transfer and the effect of heat of wetting are not modeled. The CFD model is validated by comparing simulation results with test results from U.S. Bureau of Mines experiments conducted in the coal chamber. The model predicts lower temperatures in the early stage but agrees well on the induction time for spontaneous heating. The effects of airflow rate and order of reaction on the spontaneous heating process are also examined. The calibrated CFD model is found to be useful for predicting the induction time for spontaneous heating in underground coal mines.

Jan 1, 2009

By Christopher C. Jobes, N. Kumar Kittusamy, Alan G. Mayton, Dean H. Ambrose

Researchers with the National Institute for Occupational Safety and Health (NIOSH) conducted a systematic study to evaluate seat designs on low- and mid-coal-seam shuttle cars. The purpose was to gather additional data to support earlier findings that NIOSH seats, with unique viscoelastic foam padding, are indeed improved designs for coal mine shuttle cars. This study included a larger sample of shuttle car operators than a prior NIOSH investigation. Eight shuttle car operators participated in evaluating seat designs on the basis of perceived levels of vehicle jarring/jolting and discomfort. Researchers then compared the operators’ perceptions with field-measured levels of vehicle jarring/jolting. Seven seat designs were evaluated on low- and mid-coal-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. These seat designs comprised the one already in use on each vehicle and five NIOSH designs. Experimental data were collected using accelerometers, signal conditioning amplifiers, and filters connected to a data recorder, whereas subjective data were gathered via a visual analog scale (VAS) and a questionnaire. Field trials included shuttle cars operating under full- and no-load conditions. VAS responses indicated that NIOSH-designed seats performed better relative to comfort and isolation from vehicle jarring/jolting than the existing seats used in the shuttle cars. Both mid- and low-coal-seam shuttle car operators, during no-load and full-load conditions, rated lower levels of jarring/jolting with the NIOSH seat design. Questionnaire responses indicated that shuttle car operators rated NIOSH seat designs as more comfortable. Vehicle operators most frequently suggested the addition of armrests as a way to improve the seats on the mid-seam shuttle car. The quantitative levels of vehicle jarring/jolting for the no-load condition (more severe condition for vehicle operation) showed that NIOSH seats for the mid-coal-seam shuttle car performed better than the existing seat in terms of peak acceleration and crest factor. Similarly, for the low-coal-seam shuttle car, NIOSH seats performed better than the existing seat in terms of peak acceleration, root-mean-square (RMS) acceleration, and crest factor.

Jan 11, 2006

Determine the minimum waterflow rate needed for effective control of dust produced by cutting machines used to mine water-soluble ores. Approach Conventional wet-bar cutting techniques were studied to evaluate their dust control performance, and the optimum water flow needed for dust suppression was determined. Wet-bar type cutting techniques are used to help control mine dust by keeping the cutting chain wet. As the chain cuts the kerf, it dampens the dust produced by the cutting action at the point of generation. The Bureau, under contract, evaluated three basic wet-bar techniques, as shown in the diagram: water-trickle system A uses a gravity-feed or low-pressure (less than 50 psi) pump to send water through the bar and to discharge it at the bar tip. Water-spray system B uses a low-pressure spray nozzle located at the front of the cutter head. For protection the nozzle can be located within the cutter

Jan 1, 1982

By H. B. Cooke

In connection with its researches on the crude petroleums of the United States, the Bureau of Mines has made a particular study of apparatus for the distillation of hydrocarbon mixtures. While this study is still incomplete it has already resulted in the development of considerable laboratory and semi-plant equipment, motet of which has been described in various publications of the Bureau. The laboratory apparatus (Hempel distillation) and method gives satisfactory comparative results in the laboratory examination of crudes and have been found applicable to crudes of all types, but the agreement of laboratory and plant distillations is not as close as might be desired. This is due, in part, to limitations in size and construction of the laboratory apparatus. Some refiners claim that the Bureau of Mines' laboratory method (Hempel distillation3) for distilling crude petroleum, does not show the full gasoline content of the oil, while others have stated that it indicates more gasoline than can be obtained from the crude commercially. This difference of opinion among refiners results largely from the great variation in stills used and methods of operating them. The Bureau's experience has shown that crude oils from different fields vary widely in character; in fact, that it is not yet possible to classify crude's adequately on the basis of their Down chemical and physical characteristics. As a result of the differences that exist among crudes, and of the difficulty of designing refinery equipment, no standard practice has yet been adopted for the commercial distillation of petroleum, and ma" types of stills are used in the refineries of this country. Although many factors enter into the design of equipment and the development of commercial practice in refining of crude oil, there

Jan 1, 1924

By R. W. Van Dolah

The feasibility of formulating cap-sensitive slurry explosives for use in underground mines with potentially flammable gas atmospheres was examined. Formulations containing aluminum metal as sensitizer and sodium chloride to reduce incendivity were prepared; some were cap-sensitive and had adequate air-gap. Flaked aluminum metal rather than the atomized type proved to be the more effective sensitizing agent of the formulations tested for incendivity in the large gallery of the Bureau of Mines, some were found to be suitably nonincendive.

Jan 1, 1968

Locating subsurface conductive solutions is important for many applications, including in situ mining and environmental protection. Drilling boreholes for sampling is expensive and can increase contamination by mixing water from different aquifers. Various noninvasive geophysical methods are available, but previous comparisons were hampered by different methods being used at different sites or at different times. The U.S. Bureau of Mines (USBM) compared methods at one site using the same conductive solution to improve the reliability of the comparisons. Locating deep (> 100 m) solutions is most difficult, SO the USBM selected methods applicable for such depths. Objective Improve the ability to locate subsurface conductive solutions by evaluating and comparing applicable geophysical methods. Approach The experiment was performed cooperatively with other agencies to increase the number of methods studied. The USBM, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in detecting salt water brine of conductivity 3.6 S/m collecting at the water table, 157 m subsurface. The brine was injected through two boreholes. The test site was the University's San Xavier experimental mine near Tucson, AZ. Geophysical surveys using surface and surface-borehole, time-domain electromagnetics (TEM); surface controlled-source audiofrequency magnetotellurics (CSAMT); surface magnetic field ellipticity, surface-borehole, frequency-domain electromagnetics (FEM); and crosshole FEM were conducted before and during brine injection. A total of 110,000 I. of brine was injected over one week, but the effective target volume of brine was much smaller because of mixing with ground water and dispersion.

Jan 1, 1994

By Charles L. Kimbell

The final tables of this chapter, tables 25-50, extend and expand the statistical series on production that was started in the 1963 edition of the Area Reports: International Volume of the Minerals Yearbook and that was subsequently updated and expanded in the 1965 and 1967-90 editions. Continuing the practice started in 1989, a column has been included in each of these tables providing a 5-year average for 1987-91, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1991. This group of tables now includes each of the crude minerals that ranked from? 1st to 19th in 1983 terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93 % of the estimated value of world crude mineral production in 1983. In addition, world output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-is included because of their significance as products.

Jan 1, 1993

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure'' or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", “canopies” , "roll bars" , protective structures" and other such descriptive names. In this report, "ROPS" describes the function of the structure; "FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection. “MESA” is used as an abbreviation for the Mining Enforcement and Safety Administration; "USBM" is used to abbreviate the U, S. Bureau of Mines.

By D. D. Bolstad

The Bureau of Mines has developed procedures for sampling the geometry of fractures in underground coal mines. Stratified cluster sampling and the unit area concept are applied to the collection of fracture orientation data. The use of unit area mapping, stratification, and site delineation is made to assure collection of representative data. The procedures developed here help to isolate sources of variability in the fracture patterns.

Jan 1, 1973