Search Documents

By Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to melt residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-offgas handling system, and thermal oxidizer for final offgas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 lb/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kV?A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the offgas and serves as an acid gas scrubber. The clean offgas is heated to 1,800° F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 2010

By A. W. Henderson

Methods for converting WOCl4 to WCle were investigated in small-scale, laboratory apparatus to devise a method for preparing pure WCls suitable for conversion to tungsten metal. Chlorine, COCI2, and CCI4, alone and in combination with various forms of carbon, were tested as chlorinating agents at various temperatures. More than 95 percent conversion of WOCl4 to WCls was achieved with all reagents at 8000 C in the presence of activated carbon. Only CCl4 maintained its effectiveness in the absence of carbon at 800° C. The effectiveness of carbon was found to be related directly to its surface area.

Jan 1, 1968

Synthetic dawsonite [NaAl(OH)2C03] has been prepared with crystallinity similar to that of dawsonite found in oil shale deposits of the Piceance Creek area of Colorado. Optimum experimental conditions were as follows: Na/Al atomic ratio, 43; temperature, 175° to 200° C; pCO2, 15 psig; and reaction time 5 hr. Chemical and spectrographic analysis revealed that the synthetic dawsonite was of high purity and Has essentially stoichwmetric. Similarity of the synthetic to natural dawsonite, demonstrated by X-ray diffraction, infrared spectrophotometry, and electron microscopy, suggests its suitability as a standard.

Jan 1, 1972

By J. F. Messerly

The purity of three specially prepared samples of benzene was determined with an adiabatic, low-temperature calorimeter with automatic control of shield temperature. Extensive measurements were made on each sample to determine how variations in operating procedures affect melting-point and freezing-point as well as purity data obtained by the calorimetric method. Detailed results of the investigations are presented, and effects of different operating procedures are discussed, together with problems encountered in interpretating experimental results.

Jan 1, 1963

By L. C. IlsLey

The observations made by Bureau of Mines engineers of permissible equipment installed in about 40 mines have indicated a chance for improvement in designs calling for the use of bolts , screws , studs , etc. , especially with respect to bolt sizes and protection from mechanical injury .

May 1, 1931

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 B. t. u. compared with 597,000 B. t. u. in 1936. These amounts represent roughly the heat obtainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at refineries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels were 11 percent higher than in 1930; the average operating ratio was 83 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 638,149 billion B. t. u. in 1936 to 663,966 billion B. t. u. in 1937.

Jan 1, 1938

By Alexander May

In this Bureau of Mines publication stability constants for complexes of diethylenetriamine, 2-aminoethyl sulfide, triethylenetetramine, and 1,8-diamino-3,6-dithiaoctane with copper, nickel, zinc, and cadmium were deter-mined. The amine complexes were found to be much more stable than the analogous thio complexes. The results are interpreted in terms of possible molecular structure of the complexes.

Jan 1, 1974

By John P. Gooch

Data for the ternary phase diagram for the system 1,1,2,2-tetrabromoethane/water/2-propanol at 25° C have been measured. Experimental methods used are described, and the complete ternary phase diagram is presented. A simple example is given to review the use of the ternary diagram.

Jan 1, 1972

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

TEST DECK - ALTIMETER SURVEY WITHOUT ALTMETER TEMPERATURE CORRECTION 1 BAS 8: 22 1391 1391 53. 49.

Jan 1, 1977

By W. L. Staker

Alternatives were developed to the conventional ammoniacal carbonate leaching-steam stripping procedure for recovering copper as an oxide from contaminated scrap metal. By entraining air bubbles in the leach solution, the copper dissolution rate was increased to 1.5 g/in2 of copper surface per hour, compared to 0.5 g/in2/hr produced by conventional agitation in stirred tanks. Using entrained nitrogen gas bubbles for agitation in conjunction with powdered sulfur not only resulted in rapid dissolution but also simultaneous precipitation of the copper from solution as a high-grade cuprous sulfide.

Jan 1, 1971

By Oliver Bowles

"Introduction.During recent months the Bureau of Mines has conducted a detailed study of the slate industry with special reference to increased efficiency in its production, preparation and utilization. The results of these investigations will be incorporated in a forthcoming bulletin. The purpose of this preliminary paper is three-fold. One object is to bring to the attention of slate producers certain modifications in manufacture and classification which would encourage a wider use of slate. A second purpose is to direct the thought of roofers toward the importance of proper laying of slate, and the third object is to acquaint the general public with its enduring qualities.Origin and character.Without entering into any detailed discussion of the origin and history of slate, a subject to be covered in the bulletin mentioned, it may be of interest to the general reader to know that slate is originally formed from mud or soft clay, carried down by streams and laid down in successive layers in deep water. The pressure of superimposed materials gradually compresses the clay into a firm rock known as shale. In many places this shale was, during the succeeding ages, subjected to intense pressure and folding due to mountain-building forces within the earth. This intense pressure, together with high temperature, changed the clay into other minerals such as mica, chlorite, and silica, which are very resistant to weathering, and also developed a very definite cleavage or splitting direction which characterizes the rock as slate. It is this property which renders slate of value for roofing, for, by using a broad chisel and a wooden mallet, a slate worker can readily split it into thin sheets which are later trimmed into rectangles of various sizes."

Jul 1, 1921

By Wm. W. Odell

A study of certain gas making and fuel problems peculiar to the gas industry of California has been made by the Bureau of Mines. The work was done at the request of, and in cooperation with The California Gas Research Council 2, for the purpose of obtaining basic information on the gas-making fuels available to California, and their applicability to the present and future needs of the gas industry in that State. The data obtained have been applied in outlining a construction program, and indicate the possibilities in efficiently utilizing fuels in making gas by other than the oil-gas process. This paper presents an outline of the study and a summary of the principal results obtained, with some of the more important conclusions and recommendations based on this data. Gas is produced in California by processes which are both unique and different from those common to other parts of the United States. The bulk of the manufactured gas is made in and distributed from two main districts which are centers of population - namely, the Los Angeles district and the San Francisco Bay district. The gas manufactured in the Bay district is, almost exclusively oil-gas, whereas that produced in the southern part of the State, where natural gas is available, is mostly mixed natural gas and reformed-gas, but oil-gas is the chief product when the supply of natural gas is inadequate. Practically all of the gas companies are equipped with oil-gas generating apparatus, and anticipate using it in the future. As the continued use of the oil-gas process to the exclusion of all other processes, depends upon a continued supply of oil at a low cost, and the prospect of obtaining such low-priced oil in the future is somewhat uncertain, the questions have arisen: What will the future gas-making process or processes be? When will it be necessary to make plans for the installation of different gas generating equipment, and what will that equipment comprise?

Jan 1, 1926

By John P. McDonnell

This U.S. Bureau of Mines report describes the results from an in-mine investigation of an alternative longwall gate road design. The coal mine operator modified the pillar layout (reversed the location of the big and small pillars) in a portion of a three-entry longwall gate road area. The modified pillar layout was an attempt to reduce stress and, subsequently, stress-related ground control problems (cutter roof and dynamic floor heave events) in the tailgate region during "second-panel" mining. The results from borehole pressure cells installed in the modified gate road area showed that the ground pressures in the panel edge and adjacent small pillar were significantly reduced during second-panel mining compared with ground pressures experienced in the typical pillar layout gate road areas. The reduced stress levels around the tailgate entry adjacent to the second panel, as compared with the tailgate stress levels with the typical pillar arrangement, contributed to improved tailgate ground conditions in the test pillar zone.

Jan 1, 2010

By Joseph E. Matta, John C. LaScola, Fred N. Kissell

The Bureau of Mines investigated coal storage silos to determine how gassy coal must be for methane accumulations in a silo to become hazardous and where such accumulations are likely to occur. Methane concentrations were measured in the open space above the stored coal pile, in the pile, and in the reclaiming area. No methane layering was found in closed-top silos. Reclaiming areas were as gassy as the top part of the silos. Coal samples were collected from the conveyors entering the silos in order to assess the gassiness of the coal. No simple correlation was found between the gassiness of the coal stored and the measured methane concentrations. However, at mines where the average 24-hour gas emission from the conveyor belt samples was 14 ft3/ton or more, fans or open tops were used. It appears that a large fraction of the methane released during storage remains in the void space between the coal particles.

Jan 1, 1981

By Oliver Bowles

"The manufacture of asbestos paper began commercially about 40 years age but its principal development has taken place during the past twenty-five years. The asbestos used by the ancients, termed amiantus by Pliny was used for winding sheets, tablecloths and other fabrics. It was probably chrysotile fiber and was a woven and not a felted product, and there¬fore is not to be confused with asbestos paper. There are, however, some early references to paper manufacture that are of interest. Pontoppidian, Bishop of Bergen, in his Natural History of Norway, published in 1750, refers to paper made from asbestos found in the parish of Waldens. He states that this paper did not burn when thrown in the fire, but the writing on it totally disappeared. This indicates that the primary ob¬ject was to obtain an indestructible writing paper. About 100 years later, further efforts were made with the same object in view. In 1853, a patent was issued for a process of making paper from a mixture of asbestos and alum. Many experiments were made to manufacture suitable asbestos printing paper. Some such papers contained only about one-third asbestos, the remainder being of combustible material. Such papers would burn, but would leave a white residue which retained its shape and preserved the written characters. On account of the difficulty of obtaining a smooth and even surface, and the tendency for the material to absorb ink like blotting paper, asbestos paper is not well adapted for writing or printing purposes. Other early uses of asbestos paper were for ornamental wall-paper and carpet linings. None of the uses mentioned above have developed to anything of importance in a practical way, but the manufacture of asbestos paper has become a very important industry, and it has found extensive uses in ways that were never dreamed of by the early investigators.It is recorded that the first sheet of asbestos paper made in America was manufactured in 1876 by John Roberts & Son Company, in a mill near Waltham, Mass. The material first used was a long-fibered amphibole asbestos from Italy. About three years later, Canadian fiber was introduced and proved to be very satisfactory. The shorter grades of fiber which would otherwise be wasted were used for the manufacture of paper and board. For several years, the product of this mill was sold through Rice Kendall of Boston, Mass. From 1881 to 1900, the H. W. Johns Company, of New York, took the entire product which was 30C to 700 tons per year. The latter company built their own asbestos paper mill at Brooklyn in 1900. Keasbey & Mattison Company, of Ambler, Pennsylvania, began to manufacture in 1897. Other early manufacturers were: the Asbestos Paper Company, at Baldwinsville, Mass„ and Mr. B. S. Binney, at Shirley, Mass. The number of manufacturers gradually increased until at present asbestos paper is manufactured by the following ten companies:"

Nov 1, 1919

By Lucien Eaton

This paper describing the mining practices at Mine No. 2 of the Marquette Range, Michigan is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various minim; districts of the United States. The publication, of this information should be of interest to the industry at large and the exchange of ideas thereby made possible should be of economic value to operators in all harts of the country. ACKNOWLEDGMENTS The author is indebted to the superintendent, engineer, and mining captain of the property discussed in this paper for much of the information presented. The geological classification is taken from publications of the U. S. Geological purvey.

Jan 1, 1929

By R. V. Ramani, K. Bode

"IntroductionThe theory of particle dispersion and deposition in turbulent flow is important to many fields of science and engineering. Dispersion has been studied in some detail since the early fifties (Taylor, 1954; Fischer, 1967; Osipov and Grekov, 1968; Skobunov, 1970 and 1973; Klebanov and Martynyuk, 1974). A broad research effort has also been underway in studying the mechanics of dry particle deposition. Friedlander and Johnstone (1957) proposed a theory, according to which particle deposition from vertical pipe flow could be described by an eddy diffusion transport followed by a final flight to the surface. There have been numerous revisions and additions to this original theory (Owen, 1960; Liu and Agarwal, 1974; Liu and llori, 1974; El-Shobokshy and Ismael, 1980) The mining process essentially consists of breaking in situ materials and transporting them out of the mine. An inherent characteristic of this process is the generation of fine particles. Fine airborne particulates are associated with a number of threats to the health of the miners; fine coal dust can also result in mine-wide catastrophic incidents such as dust explosions. For these and other reasons, it is important to understand the behaviour of airborne dust particulates, particularly their generation, entrainment, transport, dispersion, and deposition in the mine environment for their control.Mine related studies on dispersion and deposition have been few. Yet, several studies of gas and dust dispersion, diesel exhaust contamination, and methane ingress into mine workings have recognized the need for developing reliable parameter values for fundamental understanding of the phenomena (Da""Yes and Slack, 1954; Hodkinson, 1957; Hodkinson and leach, 1958; Mass and Wildschut, 1966; Airey, 1969; Courtney et al., 1986; Stefanko, Ramani, and Thakur, 1974; Stefanko, Ramani and Kenzy, 1977; Bhaskar, 1987, Bhaskar and Ramani 1990; Qin and Ramani, 1989; Shankar and Ramani, 1990)."

Dec 1, 1995

By C. A. Alien

The increasing activity in oil shale has had a tendency to direct the attention of the industry to any substance from which gasoline or other oils can be secured . Cannel coal for many years has been known, as a source of oil and formerly it was the only substance from which kerosene was obtained . The name of coal oil was given to kerosene because it was derived from cannel coal before any flowing wells were brought in in the United States . In an isolated region in Southern Utah there is an unusually thick and clean bed of cannel coal which laboratory experiments indicate can be made to yield about seventy gallons of oil to the ton . This coal was first described in Bulletin 341 of the United States Geological Survey under the title of Colob coal field . This field lies at the western and southern base of the Colcb plateau and extends from the town of Cedar City southward to Kanarra and then southeastward to the town of Mount Carmel . Cedar City is 35 miles south of east from Lund on the Los Angeles and Salt Lake Railroad which is the nearest railroad point . Mount Carmel is about 90 miles south of Marysvale , on the Denver and Rio Grande Railroad , which is the nearest railroad point from the eastern end of the field . The Colob coal occurs in Lower Cretaceous rocks and a number of wagon mines have been opened on the seam in the vicinity of Cedar City , Kanarra , and Mt. Carmel , but between these places the field has been very little prospected . The cannel coal , so far as known at present , is limited to a small area on the head waters of the north fork of the Virgin River in Township 39 and 40 South , Range 9 East . In this region it occurs as a bed 5-1 /2 feet thick over which lies a layer of bituminous coal 2 feet and 5 inches thick .

Feb 1, 1921

A survey of roof and pillar conditions in underground limestone mines in the United States has revealed that bench mining of the floor between pillars can cause instability in the pillars at the perimeter of the benched area. Increased loading of these pillars was observed at several mines. Large inclined geological structures that are exposed in pillar ribs were observed to contribute to pillar instability. The paper describes a study that was carried out using numerical models to assess the effects of bench mining on pillar load and stability. It was found that the benched pillars shed load onto the surrounding pillars owing to their reduced stiffness. The pillars at the perimeter of the benching area will start shedding load as soon as benching increases the height of one side of the pillar. A case study is described which shows the effects of bench mining on limestone mine pillars.

Jan 1, 2007

By D. Harrington

Fire is always a serious-menace, whether in a residential or in an industrial region; in wartime it is particularly damaging in an industrial plant. The mining industry is especially vulnerable, as its plants are generally more or less isolated front centers of population and do not have access to modern fire-fighting equipment; moreover, owing to the transitory rapture of most mines, their surface structures; are often relatively flimsy and flammable.. Trained firemen seldom are available at or near mining plants to teach the fundamentals of fire-fighting to local fire brigades, with the result that efficiency in combating actual fires is lacking. Often the attitude "it can't happen here" is held by the management of a mining property, unless the plant has suffered a serious fire; even then lapse of time is very likely to induce forgetfulness as to the possible hazards. The necessity for producing metals for the prosecution of this war has increased management's responsibility. Whereas heretofore the loss of a plant or mill by fire meant merely monetary less to the stockholder of the company, now the national interest is affected, in that the nation suffers from loss of production of minerals indispensable for war purposes.

Jan 1, 1943