Search Documents

By Joe N. Magee

As part of the important program of promoting conservation and efficient utilization of petroleum, Bureau of Mines engineers are making studies of secondary oil-recovery projects throughout the United states and publishing reports setting forth the pertinent facts so that others may profit by the experience gained. This report presents the results of a study by engineers of the Bureau of Mines, stationed at Franklin, Pa., of secondary oil recovery in a part of the Cabin Creek field, Kanawha and Boone Counties, W. Va., where natural gas is injected into the reservoir to stimulate oil production. Most oil produced in the Appalachian region at present is obtained from stripper fields in which almost all natural energy has been dissipated. Secondary-recovery methods are used extensively in many oil-producing areas of New York, Pennsylvania, West Virginia, Ohio, and Kentucky for recovering oil not produced by primary-production methods. The part of the Cabin Creek field reported in this study is shown in figure 1 and has been designated by the operator as project 4. In 1944 the developed area of the entire field was approximately 4,200 acres, and the area of project 4 was about 600 acres. In the developed area of the project the oil reservoir is in the Berea sandstone and occurs at 2,914 to 3,410 feet.

Jan 1, 1952

By G. R. Palmer

Preliminary studies by the Bureau of Mines were conducted to determine the feasibility of a multiple-compartment, ion-exchange (MCIX) column simulator for examining the effect of multiple-orifice plates in the column. A rectangular, five-orifice, three-compartment, MCIX simulator with a cross-sectional plate area of 0.66 ft2 was used for the investigation. Orifices with open areas of 1, 3, and 5 percent were used with various operating conditions. The study was separated into three separate sections: (1) solution flow effect, (2) fluidization effect, and (3) resin transfer effect. The solution flow and fluidization studies showed that for solution flow rates of about 3 gpm/ft2, a I-percent open area plate functioned best, while at solution flow rates of 9 and 15 gpm/ft2, the best open areas were 3 and 5 percent, respectively.

Jan 1, 1981

By L. T. MCELVENNY, Robert B. McElwaine, M. Clair Smith

Production of mercury from the cinnabar deposits of the southwestern Arkansas mercury district began in 1931 , reached its peak in 1942 , and ended in 1944. The mines are now idle . Virtually all the cinnabar was obtained from deposits in a belt , about a mile wide , of steeply dipping sandstone beds in the overriding blocks of three thrust faults . The belt was productive for a length of about 27 miles eastward from eastern Howard County, through Pike County, into Clark County . During the early life of the district, Federal agencies watched and recorded its progress as a contributor of a strategic metal, and later, during the war, conducted investigations designed to advance its development . In 1941 , the Bureau of Mines and the U. S. Geological Survey cooperated in investigations on eight mineralized areas in the western part of the district , to wit : Hales mine , U. S. mine , Lulu Bell property, Hopkins Hill , East Gap Ridge , Gap Ridge , Parnell Hill , and Section 17 mine area . U. S. Geological Survey prepared both surface and mine maps and designated the areas to be investigated ; the Bureau did the drilling , trenching, and sampling involved in the investigations . Twelve holes , aggregating 3,539 feet of bore , were diamond drilled on six properties ; 5,309 linear feet of surface trenches were bulldozed in six areas and 19 samples taken from them ; and 86 underground channel samples were cut in two adits on one property . In 1944 , the Bureau of Mines measured mine dumps and calcine dumps in the district in an investigation of their mercury content . Two mine dumps and one calcine dump were sampled . The data pertinent to the work done by the Bureau are included in this report .

Oct 1, 1950

By J. H. Field

Capital and operating costs have been estimated for removing sulfur dioxide from flue gases of a powerplant of 12,000-kw. capacity by liquid-purification processes, using limestone, ammonia, or sodium sulfite as the reactant. The annnonia and sodium sulfite processes yield end products that may be marketable. Coals containing about 1.5 and 5.0 percent sulfure have been considered. The sulfur dioxide content of the gases to be treated is 0.083 and 0.30 percent, respectively. Estimates have been made for 90-percent removal of the sulfur dioxide from both gases. A third instance has been considered in which 70 percent of the sulfur dioxide is removed from the flue gas of 0.30-percent concentration. The scrubbed gas would contain 0.09 percent sulfur dioxide, which might be within the permissible limit for discharge to the atmosphere in most areas. Although it is unlikely that flue gases with sulfur dioxide concentrations of less than 0.10 percent would require purification, a cost estimate for such a gas is included because an estimate is available for a British plant employing the limestone process at these conditions. Capital investment and operating costs, with no credit for products, are lowest for the limestone process for gases of both concentrations. Crediting the ammonium sulfate and sulfur produced in the ammonia process at their market prices at the end of 1956 of $32 and $28 per ton, respectively, the operating costs of the ammonia process become the lowest for purification of the gas containing 0.30 percent sulfur dioxide. The operating costs of the sodium sulfite process for purifying gas of high sulfur dioxide content approach those of the limestone process when the byproduct sulfur dioxide is credited at $14 per ton. Even if credit for products is allowed for the ammonia and sodium sulfite processes, the operating costs are higher than those of the limestone process for the gas of low sulfur dioxide content. Because of the large quantity of materials that would be produced by removing sulfur dioxide from a relatively small number of plants, credit for products should be allowed with extreme caution.

Jan 1, 1959

By F. W. Hoertel

The Bureau of Mines investigated the use of depleted uranium as a sacrificial anode for the cathodic protection of submerged and underground structures of iron , steel , and copper . Uranium-metal couples were tested in simulated marine environments of varying oxygen contents at pH values between 5.5 and 8.5 and under simulated boiler service condition in Rolla , Mo. , city water . Similar couples were tested in samples of Missouri soils to simulate underground service . Uranium remained anodic to iron , steel , and copper in the simulated marine environments and under simulated boiler service if the electrolyte was oxygen- free city water . Uranium appeared to offer limited protection to iron , low- carbon steel , stainless steel , copper , and zinc in the simulated underground tests . Uranium anodes offer a space advantage because 1 cubic inch of uranium gives approximately the same protection as 2 cubic inches of magnesium or 1-1 /2 cubic inches of zinc .

Jan 1, 1963

By J. G. Kirby

According to the Bureau of Mines annual survey, there were 319 petroleum refineries in the United States as of January 1, 1957 capable of processing 9,123,674 [ ]-barrels of crude oil daily. This was the first time in eleven years that the total number of refineries increased. The crude throughput capacity of the refineries increased 491,284 barrels daily (6 percent) above the January 1, 1956 capacity. The East Coast and Texas Gulf Coast refining districts accounted for 60 percent of the additional capacity installed. Three new refineries were put into operation on the East Coast during the year with a total daily crude throughput capacity of 154,434 barrels while the other refineries in the district report a net loss in capacity, installing equipment capable of processing 140,000 barrels, but dismantling equipment with a capacity of 150,100 barrels. In the Texas Gulf Coast district, one new refinery with a daily crude oil capacity of 5,000 barrels was placed in operation in 1956 and 143,700 barrels of crude capacity was added to existing refineries. The capacity of the average refinery to process crude oil increased from 27,145 barrels daily to 28,601 barrels in 1956.

Jan 1, 1957

By K. J. Liles

To encourage the development and conservation of the Nation's ceramic raw materials, the Bureau of Mines, U.S. Department of the Interior, under an agreement with the Georgia Department of Natural Resources, evaluated samples from a clay resource located in Clay County, Ga., for use as a raw material for lightweight aggregate. The physical properties of clay samples, taken from 5-foot increments of drill cores from 11 holes, were determined. Raw materials were plasticized and extruded to produce 1/2-inch by 1-inch pieces and fired in a rotary kiln to produce lightweight aggregate samples. The resulting expanded material had excellent loose pour weights ranging from 30 to 37 lb/cu ft. The expanded test materials were crushed, sized, and used as aggregate to form concrete cylinders. The unit weight and compressive strength of the cylinders averaged 106 lb/cu ft and 3,350 lb/sq in, respectively; these values meet American Society for Testing and Materials specifications for structural concrete. The clay from the drill cores was also used to make test bars that were evaluated for building brick.

Jan 1, 1980

Improve the safety of mine workers by developing a sensitive ground-fault relay system capable of detecting and isolating low level ground faults and thereby minimize the danger of electrocution. Approach Inadvertent, direct contact with energized conductors in underground coal mines is a major cause of electrocutions. Although relay systems designed to protect workers against such fatal accidents do exist in some industries, there are no effective ground-fault-sensing relay systems that address the special problems presented by power systems designed for U.S. mines. The Bureau of Mines conducted research to design and construct a sensitive ground-fault relay for use with low-voltage, alternating current (ac) mine electrical systems. Such a relay, sensing current leakage or faults in an electrical system, would send a trip signal to a circuit interrupting device which would then shut down power.

Jan 1, 1986

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

By J. S. Browning

The physical properties and specific gravity ranges of various liquids and salt solutions used for laboratory sink-float separations of rocks or minerals are presented. The test equipment and techniques employed by the Bureau of Mines in making sink-and-float separations of particles as coarse as 3 inches to as fine as 400 mesh are described. Also discussed are methods of recovering and reclaiming the liquids or salts from the minerals and wash solutions, as well as the hazards encountered and precautions to be followed while working with the materials. The laboratory use of various liquids for separating minerals of different specific gravities has been recognized for many years. During this time, laboratory sink-float procedures have proven their utility as a rapid and moderately accurate means for determining the mineral content of ores, test products, and plant products in certain nonmetallic concentrating operations, such as those producing mica, spodumene, kyanite, and so forth. These procedures also have been used as analytical tools for determining the mineral content and associations of other metallic and nonmetallic ores.

Jan 1, 1961

By H. Dolezal

An investigation was made on the use of magnesium for the direct reduction of rutile to make low-cost, offgrade titanium which could be upgraded to an acceptable grade of metal by electrorefining. Reductions made with charges containing magnesium chloride under hydrogen yielded products with oxygen con-tests close to the theoretical equilibrium composition. Two reduction products were made from rutile for use in electrorefining amenability tests: (1) a product from reduction in an inert atmosphere which contained 88.9 percent titanium and 4.42 percent oxygen, and (2) a product from reduction in a hydro-gen atmosphere which contained 92.5 percent titanium and 2.40 percent oxygen. Reduction products obtained under both of these conditions were amenable to electrorefining.

Jan 1, 1965

By W. D. Haselton

This paper dealing with the mining methods used in producing iron ore from an underground operation located in the central-western part of the Mesabi Range in Minnesota is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The mine here discussed was laid out in accordance with a plan adapted to a rather unusual type of ore body, the nature of which is such that the mining method necessarily differs in certain respects from the method used at most of the mines in this district. A description of it may therefore be of interest.

Jan 1, 1930

By Richard D. Miller, Geraldine P. Norrell

This publication contains routine analyses and related source data for 295 natural gas samples from 18 States collected during calendar year 1963 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Five previous publications have been made to present the results of 5,998 gas analyses made by the Bureau of Mines Helium Activity , prior to 1963. The first three , Bulletin 486,5 Bulletin 576,6 and Bulletin 617,7/ contain analyses and source data on 5,214 gas samples collected from 1917 to January 1 , 1961. The fourth and fifth publications , which are published as Information Circulars , supplement the three Bulletins and contain 784 analyses of samples collected during 1961 and 1962. The present Information Circular is the third annual publication supplementing the three Bulletins .

Jan 1, 1965

By Richard A. Thomas, Michael J. Sapko, Gary L. Mowrey, William D. Monaghan, Michael A. Trevits

Over the years, more than 20,000 mine seals have been erected in underground coal mines in the United States. Seals are used extensively in underground mines to isolate worked-out areas, active mine fire zones, and to control water inundations. Seals are most often built directly in the mine and can be fabricated from blocks made of wood or cementitious material. Recently, several explosions occurred within sealed areas of underground U.S. coal mines. These explosions, believed to be initiated by lightning strikes on the surface, destroyed numerous seals and caused considerable damage external to the sealed area. The National Institute for Occupational Safety and Health is conducting research to develop design guidelines, to investigate noninvasive techniques to characterize seal strength properties, and to evaluate seal test methods. As part of this work, a 30-ft wide, 16.1-ft tall and 4-ft thick seal was built in an underground experimental mine using cement and foamed water. Two types of noninvasive techniques are currently being investigated, namely the Schmidt Hammer for measuring compressive strength and ground penetrating radar (GPR) for detecting the presence of anomalies (e.g., voids, discontinuities) within the seal. Once these noninvasive tests were completed, the seal was subjected to destructive explosion testing. This study presents the results of the Schmidt Hammer tests, GPR scans, and the characteristics of seal failure during explosion testing.

Lower noise exposure levels for operators and cleanup personnel working in portable nonmetallic mineral crushing and screening plants.

Jan 1, 1983

By Albert E. Long

Preliminary experiments conducted in 1949 with a few diamond bits in which the diamonds in the bit crowns were set in hard-vector directions indicated that a substantial saving could be effected when a high percentage of the diamonds were oriented in this-manner. It was realized, however, that many additional tests would have to be performed before a positive trend could be established and the possibility of coincidence eliminated. Therefore, a long-range series of experiments was planned to investigate various phases of the problems related to the orienting of diamonds in diamond bits. This report (the third in a series) 2/3 presents the information obtained from tests conducted to investigate more fully the effects of orienting high-grade drill bort in diamond bit crowns. In these tests, the drill bort were oriented in both hard-vector and soft-vector directions in the crowns of AX-size bits. Test drilling was done in a dike of saussuritized dacite porphyry similar to a fine-grained granite in hardness e drillability.

Jan 1, 1954

By Robert E. Wood

[The temperature dependency of the low-density thermal conductivity coefficients, ?°T, of nitrogen, 100° to 1,200° K, is correlated with the Keyes' equation, ?T ½ -1 -12/T) WT = aT+ bT 10 The equation ?T,P = ?°T +a[ ]ß represented 509 experimental higher V pressure thermal conductivities in the temperature range 131.2° to 973.15° K for pressures to 500 atmospheres, with a mean absolute deviation of 2.35 percent. This equation was used to compute thermal conductivities of gaseous nitrogen for 47 pressures, 1 to 240 atmospheres, and 110 temperatures, 133° to 740° K, which are common to conditions encountered in Bureau of Mines helium purification processes. Isobaric heat capacities, CP, and viscosities, ?T,P, from previous work were combined with the present thermal conductivities, ?T,P, to compute Prandl1 numbers, C?T P / ?T ,P, of nitrogen. Tabular values of Prandtl num¬bers are presented for 49 pressures, 1 to 240 atmospheres, and 75 temperatures, 133° to 740° K. Estimated uncertainties are ±5 percent in the tabulated thermal conductivities and ±15 percent for the computed Prandtl numbers. However, the uncertainty may rise to ±10 percent for thermal conductivities and to ±30 percent for Prandtl numbers as the critical conditions of nitrogen are approached.]

Jan 1, 1971

By R. E. Cerullo

Many computer programs have been written which are capable of performing a least squares fit, both linear and nonlinear, to data gathered by the petroleum researcher. However, when the petroleum engineer tries to program methods of analysis he has used manually in the past, such as forecasting production by decline-curve analysis, more than a knowledge of the use of existing least squares programs becomes necessary. It is the intent of the authors to report the techniques used in the development of such a decline-curve program.

Jan 1, 1970

By M. C. Irani, Maurice Deul, M. G. Zabetakis, T. G. Bobick

This survey was conducted to determine the magnitude of the methane emission and control problem in U.S. bituminous coal mines. The resultant data indicate that the emission rate for any given coalbed depends primarily on the coal production rate and on mine depth, as well as on the nature of the coalbed and the surrounding strata. An excellent correlation was found between (1) the methane emission rate and (2) the product of coal production rate and mine depth for the mines in the Pittsburgh, Pocahontas Nos. 3 and 4, and the Illinois Nos. 5 and 6 coalbeds. The highest total emission rates found in U.S. bituminous coal mines were as follows, in million cubic feet per day: Monongalia County, W. Va., 39; Marion County, W. Va., 30.4; McDowell County, W. Va., 13.1; Washington County, Pa., 11.9; Greene County, Pa., 11.4; Buchanan County, Va., 21.6; Jefferson County, Ala., 10.3; and Franklin County, Ill., 6.6.

Jan 1, 1972

To pinpoint dust sources and to improve dust control on longwalls. Approach Use short-term gravimetric sampling to determine the severity of various dust sources, and to evaluate dust control techniques used in longwall mining. Short-term gravimetric sampling can be used to isolate dust levels produced by various dust sources. How It Works Traditionally, gravimetric samples have been collected over an 8-hour shift, yielding time-weighted, average dust concentrations. This method gives a good indication of the full-shift respirable dust exposure of underground workers, but is less than satisfactory for identifying dust sources, determining their severity, or for evaluating the effectiveness of dust control techniques. Short-term gravimetric sampling uses equipment available to all mine operators. Two individuals composing the survey team each collect multiple (three to four) gravimetric samples during selected segments of the mining cycle. Multiple samples are necessary to insure accuracy, and to obtain a valid average measurement of the respirable dust concentration when sampling for short periods of time (typically 20 to 30 minutes). The gravimetric instruments may be carried in a sampling package or in a "sampling vest." A fishing vest with four large pockets can be used for this purpose. The sampling pumps are carried in pockets and the sampling head assemblies arc hung across the front of the vest.

Jan 1, 1982