Search Documents

By Hendrik Gerritsen

The research to be described is directed to the construction of an instrument that detects methane in air. The principle on which it is based is that methane gas absorbs infrared radiation in the wavelength range of about 3.2 to 3.4 micron. Solid state p-n junctions of composition In, .97Ca.03As emitting radiation in a band centered at 3.3 micron were grown by liquid epitaxy on InAs. Fight separate growth cycles and a total of 200 diodes were measured to determine total power, wavelength peak, spectral. half width and reproducibility of the method. In order to compensate for temperature changes, dual emitter systems (one InGaAs, and one InAs diode) mounted on the same TO-5 header were made. These devices were imaged, using a folded optical path cell, on large area InAs detectors, grown by a planar diffusion technique. In the 0-50°C range the primary temperature sensitivity is in the InAs detector rather than in the emitters. Several methods to reduce the overall temperature sensitivity to within acceptable limits were demonstrated. Humidity was shown to have a negligible effect on the measurements.

Jan 1, 1976

By Byron M. Bird

"The prevailing practice of washing unsized coal, 1/2-inch and finer, to 1/8-inch and finer, on a table is subject to certain limitations which are commonly overlooked. In some instances good results are obtained by this method, but often the opposite is true and the efficiency of the washing operation is low. Although the separation taking place on a concentrating table is not fully understood, the actual distribution of particles of various sizes and specific gravities was determined a number of years ago by ore-dressing investigators. Hence this paper consists of an analysis of an old problem by new methods. The experimental data on which the discussion is based were obtained in the course of coal-washing investigations conducted by the U. S. Bureau of Mines at the Northwest Experiment Station in cooperation with the University of Washington and with certain coal operator: of that State.Experimental WorkThe general method of study has been to take a large number of zonal products from the table, and separate them according to specific gravity and size into their component parts. The table used is one of the standard commercial sizes with a diagonal deck. The coal to be washed is split into representative portions, which are stored in separate bins. One portion is used for ""timing as"" the table; the products are collected continuously in the same turned to the feed bin, and thus a closed circuit is completed. When the despite conditions on the table are obtained, coal is fed from one of the re. After the table is operating smoothly the entire product is minute; such a sample is sufficiently large to represent accurately the work of the table and at the same time to minimize the effect of beginning at the end next to the head motion, separate samples are made for each foot along the edge of the deck."

Jun 1, 1926

By W. J. Fullerton

This paper is one of a series being prepared by the U. S. Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States, end deals directly with methods and costs at the quarry and mill of the North American Cement Corporation at Catskill, N. Y. The process of manufacturing cement is described only as far as the final grinding of the raw materials. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual producers, as well as to the industry as a Whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding; of the scone of the cost tabulations may ensue.

Jan 1, 1931

By R. W. Smith, S. H. Ash

Marked progress in safety has characterized the operation of coal mines in general in the State of Washington during the 5- year period 1928-1932 , particularly during the years 1931 and 1932. Physical conditions such as steep pitches , inherently bad roof and floor , prevalence of gas , and explosibility of the dust of Washington coals present certain definite hazards . Although advances have been made in accident reduction in Washington , the State still has far to go in that direction . The State has endeavored to reduce its coal -mine accidents by the usual method of making certain definite safety requirements mandatory . The value of education has not been underrated , but the educational method used has not altogether achieved the res lts desired by the industry itself , particularly within certain imdividual organizations . The past 2 years have witnessed a growth , in certain instances , of the essential ideas that the observance of safety precautions on the part of all is demanded if accidents are to be reduced , and that the initiating and carrying out of any program to promote and obtain desired results in accident elimination must begin and function from the top downward . Mining operations of Washington mines have been described in various publications of the United States Bureau of Mines .

Jun 1, 1933

By Victor E. Kral

"SUMMARYFollowing a magnetometer survey on the McCoy iron deposit, a trenching and drilling program was carried out by the Bureau of Mines in August 1944.This deposit is 32.3 miles southwest of Battle Mountain in the McCoy Mining District, Lander County, Nevada, and lies on the east flank of the Fish Creek Mountains at an altitude of 5,400 feet, about 1 1/2 miles south of the gold camp of McCoy.Total production from the deposit has been 400 tons of magnetite, mined by hand and shipped to the west coast for ship's ballast.Bureau drilled two holes to a total depth of 92 feet and excavated 12 feet of trenches. Both holes were drilled in the same ore body and engineered magnetite ore 14 and 11 feet thick. Trenching was used successfully to show the lateral limits of the ore.Magnetite ore bodies were found to occur as replacements of a limestone bed in quartzite. They outcrop near and parallel to the exposure of a diorite entrusting that forms a long westward-trending ridge. Although magnetic outcrops can be traced for 5,000 feet trenching definitely proved the ore bodies to be disconnected to have little or no lateral extent beyond their outcrops. Only two ore bodies more than 10 feet thick were found; one of these is the inaccessible to and the other was drilled by the Bureau."

Jan 1, 1947

By K. E. Hjelmstad

During an underground mine fire, air can be rapidly depleted of oxygen and contaminated with smoke and toxic fire gases. Any delay in warning miners could have disastrous consequences. Unfortunately, present mine fire alarm systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in mine area coverage. Recent research by the U.S. Bureau of Mines has demonstrated that ultra low frequency electromagnetic signaling can be used for an underground mine fire alarm. In field tests of prototype equipment at five mines, electromagnetic signals from 630 to 2,000 Hz were transmitted through mine rock for distances as great as 1,645 m to an intrinsically safe receiver. The prototype system uses off-the-shelf components and state-of-the-art technology to insure high reliability and low cost. When utilized, this. technology would enable simultaneous and instantaneous warning of all underground personnel, regardless of their location or work activity, thereby increasing the likelihood of their successfully escaping a mine disaster. This report presents the theoretical basis for through-the-rock ultra low frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 2010

By Aner W. Erickson

Magnetite iron deposits on Tolstoi Mountain were examined as part of the investigations by the Bureau of Mines of iron and copper ores on Prince of Wales Island. The Tolstoi Mountain project was a part of a program for investigating mineral deposits in Alaska, under the general supervision of R. S. Sanford, acting branch chief.

Jan 1, 1948

By James P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, were evaluated: two red shale, two fireclay, one silicon carbide, one silica, one carbon, and one high-alumina. Samples were exposed to 10 wt pct H2S04 at 50° C and 10, 30, 50, 70, and 90 wt pct H2S04 at 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were observed in the silicon carbide and car-bon materials. Weight changes and the leach rate of Al, Ca. Fe. K, Mg, Na. Si, and Ti were also monitored. The most severe corrosion conditions were at 90° C and 30 to 50 wt pct H2S04 for the acidproof and at 10 wt pct H2S04 for the acid-resistant materials. The silica and the high-alumina materials were the most acid-resistant, followed by the higher density red shale and fireclay.

Jan 1, 1986

By Earl L. Phillips

The Bureau of Mines conducted laboratory tests on samples of pozzolaniccement concrete to develop a low- strength backfill . Results show that support costs can be lowered by replacing a portion of the portland cement in mine backfill with pozzolan ( fly ash ) and lime . Unconfined compression tests on various ratios of fly ash to cement in 84 samples produced compressivestrength curves that can be used to estimate the best backfill mix for any mine .

Jan 1, 1964

By T. E. Gray

This report describes the preparation characteristics of the more significant coals in Dickenson County, Va. It is one in a series planned to determine which coals are suitable for the production of metallurgical coke either as mined or after beneficiation. Nearly 4 million tons of coal was produced in Dickenson County in 1955, of which approximately 2.7 million tons was cleaned mechanically in 5 cleaning plants. The Federal Geological Survey has estimated that nearly 1,300 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By S. J. Pearce

The Bureau of Mines has prepared, as circumstances have dictated, a series of Schedules setting forth the minimum requirements that various types of equipment should meet to be considered safe and satisfactory for use in certain hazardous or unhealthful conditions. These Schedules cover a wide variety of devices ranging from explosives to electrically operated mine locomotives. This paper deals with those Bureau of Mines Schedules under which respiratory protective devices are tested and approved, and its purpose is to explain the function and operation of these Schedules. Provisions have been made for testing and approval of the following types of respiratory protective devices: Self-contained breathing apparatus,2/ supplied-air respirators,3/ gas masks,4/ dispersoid respirators,5/ and chemical cartridge respirators.6 These devices are tested at the Central Experiment Station of the Bureau of Mines in Pittsburgh, Pa. Self-contained breathing apparatus is tested by the Safety Branch, and the other types of respirators are tested by the Health Branch.

Jan 1, 1951

Provide longwall operators with an alternative strategy for placement of gob gas ventholes to improve gas production.

Jan 1, 1995

By Ruth F. Brinkley

This circular summarizes the research and technologic activities and publications of the Federal Bureau of Mines Division of Explosives Technology4/ during fiscal year 1959 (July I) 1958-June 30, 1959). Part I briefly describes the programs that were active during the report period and presents a summary of some of the information not published elsewhere. In many instances the results are only preliminary and are subject to revision on the basis of continuing investigations. Detailed reports of all programs not security classified will be made later. Part II lists and describes briefly the publications of the Division during fiscal year 1959. If the published material has some bearing on activities still current during the report period, this is indicated by references in Part I.

Jan 1, 1961

Case 1: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ] Case 2: A crew was preparing to remove a pump from a well when the hoist boom contacted a 4160-volt power line. The hoist operator was electrocuted. [ ]

Jan 1, 2005

By J. B. Zadra, H. J. Heinen

Electrowinning molybdenum from oxide feed materials dissolved in a variety of molten baths was investigated . A NaCl - NaF - Na₂ B₁ O -Mo0, system operating at 1,000 ° C in a cell without a protective atmosphere gave the best current efficiency , metal - to - cathode adherence , and purity of electrowon Technical - grade molybdic oxide , containing associated impurities of aluminum , iron , copper , silicon , and tungsten in combined quantities of 10 percent , was used as feed material to produce dendritic crystals of molybdenum metal containing less than 0.5 percent total base metal , carbon , and oxygen impurities . Arc - melting molybdenum electrowon from either chemically pure or commercial - grade Mo0, produced ingots that contained less than 0.1 percent total impurities and had hardness readings of 168 to 200 Vhn .

Jan 1, 1964

By A. C. Fieldner, G. W. Jones

Tests were made at the Government Fuel Yard , operated at Washington , D. C. by the Bureau of Mines , Department of the Interior , in order to determine and improve the adjustment of the carburetors on the trucks used for transporting coal from the Fuel Yard to the different Government buildings in Washington . The tests were made possible through the hearty cooperation of G , S. Pope , engineer in charge of the Fuel Yard . Joseph Burrows and A. E. Foote of the garage department assisted during all the tests and supplied information on the mileage obtained by the trucks for the months preceding and succeding the time the tests were made . The Mack trucks used range in capacity from 2-1/2 to 7-1/2 ttoonnss .. The majority of the carburetors were Stromberg G- 3 type , as shown in Table 2. During the winter months , when the demand for coal is heavy , from 30 to 35 trucks are used . At the time the tests were made , only about ten of the trucks were in daily use , owing to the small demand for coal during the summer months , and scarcity due to labor conditions . Samples of the exhaust gas were taken on the trucks kept in service for summer hauling in order to determine the carburetor adjustment as used . Changes were then made to a more economical adjustment wherever possible , without sacrificing flexibility of operation and power . In every case the adjustments were maintained for maximum power , but were adjusted to the leanest position to give that power . In all but one case the carburetors were found to be adjusted too rich for maximum power and economy . These results are considered in detail in a later part of this report .

Jun 1, 1923

By J. C. LaScola

Development of methanometers and anemometers for underground use in coal mines is reviewed. The first semicontinuous recording methanometer was developed in 1961 in West Germany. The Bureau of Mines developed an instrument using; pellesters that was a continuous recording methanometer. Expansion of freon gas created a vacuum which pulled the methane-air mixture through a tube to an electrically heated, catalyst-impregnated pellester where the mixture was burned. The National Coal Board of England developed a continuous recording methanometer based on the principle of the Davy flame safety lamp. A thermo-pile was used to sense the hurt output of the flame. Finally the Bureau of Mines improved its methanometer by eliminating the freon gas and using a diffuser head to a monitor methane-air mixtures. Development of recording anemometers proceeded from the use of a photo¬cell and light source to sense rotation of the Biram-type anemometer blades to the use of a Hall detector to sense, rotation by measurement of electromagnetic pulses.

Jan 1, 1969

By M. M. Fine

A laboratory mineral-dressing investigation of manganese ore from the Martin mine, Independence County, Ark., succeeded in recovering ferrograde manganese products. Sintered flotation concentrates analyzing 40.7 and 41.4 percent manganese at overall recoveries of 54.6 and 47.7 percent, respectively, were produced from preconcentrated feed, Preconcentration of the ore for flotation included treatment by magnetic separation and by a combination of magnetic separation and heavy-medium processing. The mineral-dressing study of the Martin mine rhodochrosite ore was part of a general program of the Bureau of Mines to develop domestic sources of strategic minerals, including manganese. Several such potential sources of manganese exist in the Batesville, Ark., district, one of which is represented by the Martin mine. Although the Martin mine area has not been delimited with respect to total reserve tonnage, it is considered to be one of the more important occurrences of manganese in the district. It is estimated that several 100,000 tons of manganese carbonate ore are present in this and similar properties.

Jan 1, 1954

By J. E. Hamak

This publication contains analyses and related source data for 144 natural gas samples from 19 States. Of the total samples, 139 were collected during calendar year 1990. The remainder were collected earlier, but releases granting permission to publish were not received until 1990. All samples were obtained and analyzed as part of the U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free-market economies. This survey has been conducted since 1917. The analyses were made by mass spectrometer and chromatograph.

Jan 1, 1991

By A. F. Colombo

Laboratory-scale tests were conducted by the Bureau of Mines on an argillaceous Michigan copper ore and mill tailing to determine the feasibility of leaching with acidified ferric sulfate solutions. The ore and tailings, containing 1.24 and 0.24 percent copper, respectively, were from the White Pine Copper Co., Ontonagon County, Mich. The investigation showed that ferric sulfate leaching of the ore and tailings followed a predictable pattern. Thus, with 4 hours of leaching, up to 58 percent of the copper in the ore was extracted, but prolonged leaching (2 to 3 weeks) was required to dissolve more than 90 percent of the copper. Similarly, about 50 percent of the copper in the mill tailings sample was dissolved in a few hours, but 8 days or more were required for extractions of over 90 percent.

Jan 1, 1962