Search Documents

By Slavoljub D. Maksimovic

At some coal mines, methane gas is released during raise drilling. At the request of the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, the Bureau of Mines conducted ventilation surveys at different raise drill sites to assess various methods of reducing methane concentration. The resulting data indicate that raise drill shaft cavities are ventilated by air compressors, vacuum pumps, auxiliary blower fans, and free intake air from the surface. The compressors, pumps, and fans operate simultaneously or separately. At the bottom of the shaft cavities, ventilation is controlled by regulators and airlocks. Methane is monitored, measured, and periodically sampled on the surface, at the bottom, and at different levels in the shaft cavities. Maximum concentration of 3.5 percent was measured in one shaft in West Virginia. Air velocity down the raise drill shafts is always very low, Maximum recorded air down the drill stem was 3,000 cfm, which can be increased by adding air compressors. The best way to ventilate shaft cavities is through the simultaneous use of air compressors and vacuum pumps. If the methane concentration cannot be reduced with additional compressors, then the inside diameter of the drill rod should be increased, or larger pilot hole drill bits should be used.

Jan 1, 1981

By D. M. Lewis, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, J. H. Kang, V. Castronova

"Tetrandrine is a bisbenzylisoquinoline alkaloid which has been shown to exhibit antifibrotic activity against silicosis. Tetrandrine is characterized by its strong binding to alveolar macrophages and inhibition of particle-induced respiratory burst activity in these phagocytes. In contrast, tubocurine and tubocurarine are structurally similar to tetrandrine but exhibit little effect on fibrosis or activation of alveolar macrophages. The objective of the present study was to test the effect of tetrandrine on macrophage production of monokines in response to occupational dusts, and to determine tetrandrine's effect on monokine-medicated cell growth using a mouse thymocyte proliferation assay and lipopolysaccharide (LPS) as a positive control. Stimulation of alveolar macrophages by respirable silica dust resulted in a release of monokines which caused a fourfold increase in thymocyte proliferation. Coal dust, on the other hand, had no effect on macrophage production of this cytokine. Tetrandrine was found to exhibit a dose-dependent inhibition of monokine release from both silica and LPS-stimulated alveolar macrophages. In experiments where thymocytes were directly treated with tetrandrine, a dose-dependent inhibition of thymocyte proliferation was noted with both interleukin-1- (IL-1) specific and nonspecific mitogenic (concanavalin A) actions. In contrast to the inhibitory potency of tetrandrine, tubocurarine was found to have no effect on either the production of monokines by LPS-stimulated alveolar macrophages or IL-I-mediated thymocyte proliferation. These results provide a correlation between the ant:fibrotic effect of tetrandrine and inhibition of macrophage activation. INTRODUCTIONThe pathogenesis of chronic pulmonary fibrosis caused by inhalation of occupational dusts has been associated with abnormal activation of alveolar macrophages such as the release of various cytokines capable of inducing fibroblast proliferation and collagen synthesis. These macrophage-derived cytokines include interleukin-1 (IL-1), tumor necrosis factor (TNF), platelet-derived growth factor (PDGF), transforming growth factor-B (TGF-(B), macrophage derived growth factor (MDGF), and interferon [1, 2].Interleukin-1 is a major macrophage-derived cytokine that has been shown to exhibit multiple biological effects on a variety of target cells. It is known to cause leukocyte [3, 4] and endothelial cell activation [5, 6], and to affect the synthesis and maintenance of the extracellular matrix by stimulation of fibroblast proliferation [7-9], synthesis of collagens [10] and gluco-saminoglycans [11], and prostaglandin E2 production [12]. In addition, IL-1 plays an important role in the initiation of an immune response through its direct activation of lymphocytes and stimulation of the production of other cytokines, such as interferons and hemopoietic colony-stimulating factors, needed for the expression of an immune response [13]. As a major cytokine in the immune-inflammatory sequela, IL-1 is also produced by epidermal, epithelial, lymphoid, and vascular tissues after infection, injury, or antigenic challenge [14]. Agents such as lipopolysaccharide (LPS), phorbol myristate acetate (PMA), immune complexes, and particulates are known to activate the synthesis and release of IL-1 by monocytes and macrophages [15]. These substances also trigger intracellular signals leading to altered arachidonic acid metabolism. Although the mechanism is still not clear, prostaglandins have been shown to suppress IL-1 translation via the induction of cyclic adenosine-monophosphate (CAMP), whereas leukotrienes produce a positive signal for IL-1 production [13]."

Mar 1, 1992

By R. J. Fantel

The Bureau of Mines investigated the resource availability of titanium minerals from 63 mines and deposits in 12 market economy countries. These mines and deposits contain, at the demonstrated resource level, an estimated 438 million metric tons (mt) of titanium dioxide (TiO2) in the minerals rutile, ilmenite, leucoxene, and anatase. An additional 314 million mt of TiOz is available from inferred resources. If all titanium minerals and other recovered heavy minerals are sold at total costs at least equal to the January 1984 market prices, approximately 200 million mt of contained TiO2 could be recovered in total. In terms of mineral concentrates, this equals approximately 11 million mt of rutile concentrate, 187 million mt of ilmenite concentrate, 3 million mt of leucoxene concentrate, 13 million mt of synthetic rutile concentrate (in addition to the ilmenite), and 89 million mt of titanium slag. The study indicates that world resources of low-cost rutile are declining. In order to maintain future supply for high-grade titanium resources, alternate sources will need to be developed, which may include higher cost rutile mines, Brazilian anatase deposits, increased production from slag operations, or more synthetic rutile capacity from ilmenite resources, which are abundant.

Jan 1, 1986

The Department of Interior, U.S. Bureau of Mines performs the task of estimating the quantity of coal reserves existing in each state on a county by county basis. As a part of Information Circular 8655, the Bureau of Mines established the criteria for the uniform estimations of coal reserves and listed the most recent estimates of coal reserves by county and by seam. At the same time however, the Bureau recognized that these figures represented the upper bound with regard to the estimated actually usable or obtainable reserves. Recovery of these reserves are subject to the mining methods used and to the resolution of such problems as the use of poor quality coal and competition provided by conflicting land use. These problems, in practice restrict the recovery of the estimated quantities of coal reserves listed in IC 8655. Another impact, the subject of this manual, is the impact resulting from previous mining activities. In particular, many of the reserve seams included in the reserve estimates overlie or underlie mined-out coal beds. Portions of these reserve seams may therefore be unmineable or at best may have a reduced quantity of extractable coal. In order to improve the accuracy of the coal reserve base estimates, the Bureau of Mines funded an effort1 to develop a systematic methodology for estimating the coal loss associated with the impact of previous mining activity. The coal loss calculation model (CLCM) described in this manual is a result of that effort and addresses the percentage of coal loss in reserve seams due to previous overmining or undermining.

Jan 1, 1976

By G. W. Jones, F. E. Scott

"INTRODUCTION During the last war, considerable attention was given to the search for materials or combinations of materials for use as expelling agents for aerosols in the well-known ""aerosol bomb."" These materials must be free of fire and explosion hazards under normal conditions of use.In cooperation with the Department of Agriculture and other Federal agencies interested in the work, the Bureau of Mines carried out a laboratory investigation on the inflammability of- dimethyl ether-dichlorodifluoromethane air mixtures. 4/The method of investigation was essentially the same as that used in a similar investigation dealing with the inflammability of propane-butane-dichlorodifluoromethane mixtures. 4/SOURCE OF MATERIALSThe dichlorodifluoromethane (commonly known as freon-12) and the dimethyl ether were supplied by Dr. Lyle D. Goodhue., U. S. Department of Agriculture, Beltsville, Md. It was reported that the freon-12 was manufactured by the Kinetic Chemical Co. Wilmington, Del., and the dimethyl ether by the Carbide & Carbon Chemicals Corp., Charleston, W. Va..The materials were obtained in small metal cylinders and were used as received. Before using, the cylinders mere placed in an upright position, and 5 to 6 liters of the gas was released from each cylinder to the atmosphere to remove any trapped air that may have been introduced when the cylinders were filled."

Sep 1, 1947

In March, the Minister of Mines, Mrs. Judy Erola, released a mineral discussion paper at the annual meeting and convention in Toronto of the Prospectors and Developers Association. Among the mineral objectives discussed was the revitalization of the "junior" mining industry. That industry reportedly has seen its share of total exploration expenditures fall from 50% in 1969 to 10% in 1979. Some sources believe the reason to be the rise of exploration costs and more- restrictive legislation The junior mining industry reportedly was responsible for 40% of all mineral discoveries in the 1969-79 period. CZECHOSLOVAKIA Czechoslovakia expects its capacity for the recovery of gallium metal to increase from 1,650 kilograms to nearly 3,000 kilograms per year by the installation of new recovery equipment at the aluminum plant at Ziar Nad Hronom in Central Slovakia. World production data are not reported, but the United States consumed 8,000 kilograms (estimated) in 1981, of which 5,536 kilograms were imported. Gallium is recovered as a byproduct of the Bayer process for the conversion of bauxite to alumina, and from certain zinc processing wastes. It is used for electronic applications such as light-emitting diodes for visual display panels in calculators, clocks, and other instruments.

Jan 1, 1982

By Doris M. Hyde

Limited geographically by size and geo-logically by origin, smaller countries and territories of the Caribbean are nonetheless engaging in efforts to encourage the initiation of mineral and mineral-related industries. Petroleum dominates the minerals sector, which otherwise consists principally of minor quantities of construction-oriented materials, usually for local consumption. The increased cost of petroleum has adversely affected most of the world, but these islands with their economies precariously balanced on the uncertainties of agriculture and tourism are especially vulnerable to petroleum's direct and indirect costs. In 1975, the Government of Antigua acquired the financially troubled West Indies Oil Company refinery at St. Johns. The refinery ceased operations in 1976. In 1979, negotiations were underway to sell Ashland Oil Co. an interest in the small, 20,000-barrel-per-day refinery for $6.6 million. In 1977, Antigua granted petroleum exploration rights to the Antigua Mineral Exploration Company, which planned to drill in an undefined offshore area, possibly between Antigua and Barbuda. The company expected to spend about $200,000 per year through 1982. There have been no reports on its activity.

Jan 1, 1981

By A. M. Evans, J. H. Soulé

"INTRODUCTION Deposits of iron ore in Cherokee County, Tex., have been worked at various times in the pact, and the ore has been smelted in small local blast furnaces.Recently it was proposed to establish a charcoal blast furnace with a wood distillation plant to produce charcoal for fuel and byproducts. Financial assistance from the Reconstruction Finance Corporation was sought by George Easley and associates to enable them to purchase, move, and erect the furnace and build the required accessory plants. The furnace was to be moved from Pembroke, Fla.In August 1941, the Bureau of Mines was asked by the Office of Production Management to check the development work of Easley and associates and to ascertain (1) the iron-ore reserves, (2) the cost of mining ore and delivering it to the blast furnace, and (3) the grade and character of the ore. The Bureau of Mines was advised, while the investigation was in progress, that approximately 1,000,000 long tons of measured reserves would be sufficient to demonstrate the feasibility of operating the properties.Although deposits of iron ore are widely distributed in Cherokee County, only the Pryor Mountain, Banks and Cherokee, J. P. Acker, and Citizens State Bank tracts were sampled thoroughly by the Bureau of Mines. The iron-ore rights on these are owned by the New Birmingham Development Co., the Cherokee Development Co., or by individuals. Options to lease the ore rights were obtained by Easley, who obtained options on the Hawes Peach Orchard and Bradford tracts, also, which were examined only cursorily by the Bureau."

Aug 1, 1947

By Jr. Kauffman

The data contained in this report were obtained incidental to the Bureau of Mine's investigation of the lime-soda sinter process as applied to the recovery of alumina from siliceous bauxite, kaolin, and other high aluminous materials. The Bureau of Mines was charged by Congress to investigate processes for the production of aluminum from domestic low-grade ores. The Eastern Experiment Station at College Park, Md., conducted laboratory and pilot-plant investigations of the recover-y of alumina by the lime-soda sinter process. Reports by the College Park staff covering the recovery of alumina from these sources have been published. The lime-soda sinter process involves the sintering of the finely ground siliceous bauxite or clay with limestone and soda ash in a rotary kiln. During the sintering the alumina supposedly reacts with the soda ash to form soluble sodium aluminate and the silica combines with the lime to form the insoluble orthosilicate. In the early stages of the investigation it was considered desirable to know the temperatures at which the phase changes occurred during the sintering operation. The total time involved in the passage of any given portion of the charge through the kiln was 28 minutes. The exposure time of the charge to temperatures above 600° C. (decomposition temperature of kaolinite) was, roughly, half the total. The exposure to the full temperature of the kiln, 1,100° C was only 3 minutes. (Subsequently, the maximum kiln temperature and retention time were increased.)

Jan 1, 1949

By William H. Lyon

In 1950 the Program Staff of the Department of the Interior undertook an exploratory study in the projection of energy requirements of the nation. This work was reported in Bureau of Mines Information Circular 7582 by H. J. Barnett. In that preliminary study Mr. Barnett, after exploring the nature of the energy economy in some detail, evolved a method for estimating how much energy will be required in the future, based on estimates of trends in efficiency of energy utilization in specific applications, the physical output of specific energy-consuming industries, size of the population, productivity advances in the economy at large, consumer preferences, and other factors. Considerable new information was developed regarding the nature of energy demands and the possible levels of requirements for each fuel under various assumed business conditions. The study analyzed the interrelationships, including substitutions, among the fuels and emphasized the need for viewing the energy economy as an integrated albeit complex whole. This exploratory study showed a need for a single comprehensive statistical re-port that would assemble and show in a uniform manner the diverse published statistical data on energy commodities now scattered through many publications. A particularly important need was for a set of historical statistics showing the production and consumption of all energy on a B.t.u. basis. As the prospective size and nature of the future energy requirements of the nation are matters of continuing importance, this report was prepared to assist further investigations of the subject. In this report the authors undertake to assemble and present in tabular form, on a uniform basis, the production and use of each of the fuels and electric energy in the United states for three census years -1929, 1939, and 1947. The year 1947, rather than a later year, was selected because it is the most recent year for which census data are available showing the consumption of fuel by each of the manufacturing industries. It is hoped that making data for these 3 years available in one re-port will provide the needed statistical background for further studies of fuel requirements and supplies.

Jan 1, 1951

By Ernest W. Johnson

In most underground iron mines in the Lake Superior district the active workings are at considerable depth. When additional openings into such. nines are needed, operating officials are eager to discover more efficient methods of constructing them. In recent years, openings into two mines in the district were made by the borehole method,-which employs chilled-iron shot as the cutting medium. Others were made by the churn-drill method, in which pilot hole is churn-drilled and subsequently reamed to a desired but relatively small diameter. Both methods are comparatively new and unique, at least in some phases and in their application.

Jan 1, 1946

By M. M. Wong, J. E. Klosterman

Scrap beryllium chips ( nominally 96 to 97 percent Be ) were electrore fined in a prototype cell with 408 lb of electrolyte composed of 52.4 mole - percent LiCl , 36.3 mole - percent KC1 , and 11.3 mole - percent BeCl2 . The cell temperature was 500 ° C. In a typical 10-3 /4 - hour deposition cycle , 0.415 pound of metal was produced ; the metal contained impurities in parts per million as follows : C , 700 ; 0 , 610 ; Al , 34 ; Ca , 32 ; Cu , 20 ; Fe , 25 ; Mg , 9 ; and Mn , 23 . Operation of the prototype cell for 2 years demonstrated that adapting the electrorefining process to an enlarged scale of operation presented few difficulties in mechanical functions , maintenance of optimum operating conditions , and control of product purity . After the spent anode feed was leached in a 5 - percent nitric acid solution and the fine - sized particles were removed , it was recycled in some tests . The metal produced was somewhat higher in impurities than metal from the fresh scrap chips .

Jan 1, 1964

By Robert H. Ridgway

This paper presents the results of the second in the series of annual canvasses on the consumption of ferrous scrap and pig iron in the United States, inaugurated in 1935 by the Bureau of Mines and published in Report of Investigations 3329. The study was undertaken in response to requests from trade organizations and others for detailed statistics on this phase of the iron and steel industry. Thus, for the first time, producers, buyers, sellers, and consumers of iron and steel scrap have had an accurate statistical picture of this important raw material As originally contemplated, the study was to be continued on an annual basis, but, owing to budgetary limitations for the fiscal year 1937-38, the Bureau may be unable to conduct the canvass for 1937.

Jan 1, 1937

By Robert H. Ridgway

This paper presents the results of the second in the series of annual canvasses on the consumption of ferrous scrap and pig iron in the United States, inaugurated in 1935 by the Bureau of Mines and published in Report of Investigations 3329. The study was undertaken in response to requests from trade organizations and others for detailed statistics on this phase

Jan 1, 1937

By Donald W. Scott

Chemical thermodynamic properties for the ideal gas state from 0 to 1500 K are tabulated for all of the alkane hydrocarbons through C10. These properties are based on correlations of the extant data for the entropy, vapor heat capacity, and enthalpy of formation of individual alkanes and the equilibrium constants of alkane isomerization reactions.

Jan 1, 1974

By Charles H. Shapiro

[In July, 1924, the Bureau of Mines, through its Petroleum Experiment Station, undertook a field study of methods used in oil-field shops for dressing and tempering fishtail bits. The purpose of this work was to suggest chances that would be helpful to the bit-dresser in turning out better treated, harder, and tougher bits, and thus cut down the excessive loss of time caused by too frequent changing of bits. It was the intention to eliminate as much as possible the guess work connected with dressing and tempering bits under the method of judging temperature by eye, by developing; practical methods of controlling temperature. If there were some possible means of accurate temperature control, then it would be an easy matter to bring all bits to the proper temperature for maximum hardness rued toughness, thus doing away with the source of most of the trouble experienced in the present method of bit tempering. Shortly after the Bureau of Mines began its study, a chop In the Stroud, Oklahoma, oil field announced method for tempering fishtail bits that Would increase the drilling footage of each bit treated. The method accurately regulates, by the use of a bath of molten salt, the temperature to which a bit is heated before being quenched to produce hardness. There is nothing new in using silt baths for the, heat treatment of steel, but this was the first attempt to introduce it into the oil fields for use in hardening bits, and for this purpose it proved to be admirably adapted. In tempering, by the old system it is not possible to measure the temperature of the heated bit by means of an electrical instrument for that purpose, whereas this is an easy matter with the now method. If heating steel to slightly above the critical point rind quenching suddenly will bring out its best properties, their here is a method of accurately bringing the steel to that point.]

Jan 1, 1925

By S. H. Ash

A CLAY, sand, and gravel deposit known as the "buried valley" of the Susquehanna River is situated in the Northern field of the anthracite region of Pennsylvania near Wilkes-Barre. The presence of this buried valley and the uncertainty regarding the extent and physical condition of the water-bearing valley-fill deposits have made great care necessary in mining operations to avoid breaking the strata between the mine workings and the valley-fill deposits to the extent that inundation of the mine workings would follow. The principal factor that threatens to cut short the life of the anthracite industry, to curtail production, and to affect the economic structure of the people and business dependent on anthracite for their livelihood is inundation of anthracite mines (6,7).3

Jan 1, 1950

By Willard J. Tesch

The borehole surveying system described is used to measure ground movement over and near operating mines. The magnitude of any movement is con-trolled by the ground conditions, the mining method, and the mine progress. By correlating these factors with the measured movement, equations can be determined for predicting the effect of mine progress on the surrounding ground. These equations can also be used to predict the effect of mining a similar deposit with similar ground conditions. The borehole surveying system is used in cased boreholes to measure the inclination of the hole in two perpendicular planes. Grooved casing with an inside diameter of 3 inches is grouted in the hole. Two probes are used to obtain the data necessary to calculate the hole position versus depth. One of the probes contains a gyroscope, and the other contains a biaxial force-balance [s]ervoaccelerometer. Readings from the transducers in the probe are punched on paper tape by an automatic data acquisition system as the probe is pulled up the hole at 30 feet per minute by an electric winch. Readings from the inclinometer probe containing the accelerometer are used as input data to an on-line programmable calculator as they are punched on tape. The calculator computes preliminary results of the survey being made. The paper tapes obtained during the survey runs are later used as input to a computer that computes the offsets of the drill hole versus depth in true north-south and east-west planes. These offsets are printed for each foot of depth. Changes in these offsets between the first survey and subsequent surveys are a measure of the horizontal ground movement between the surveys.

Jan 1, 1976

By Wallace W. Roepke

The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60' and 90' (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate.

Jan 1, 1983

By Carlton E. Brown

This report contains information on the relation between and precision or reproducibility of counts (light-and dark-field) of the dust in liquid from simultaneous impinger, midget-impinger, electric-precipitator, and filter-paper samples. The impinger was the main sampler used from about 1922 to 1939 by industrial hygienists in the United States for collecting samples of unhygienic dust from the atmospheric environment of workers. The midget-impinger, a small modification of the preceding impinger described in 1937, has been the sampler used most since about 1939. Electric precipitators5/6/ have been used to a limited extent, mainly by the Bureau of Mines in the laboratory, for obtaining results comparable to impinger results. A filter-paper sampler for obtaining results comparable to impinger results has been described by Brown. All these samplers have a high collecting efficiency for particles larger than 1 micron in diameter revealed by the usual light-field counting procedure. However, their collecting efficiencies are quite variable for the smaller particles revealed by the dark-field counting procedure used in this study. Published information on the relation between the results of these samplers is limited and scattered. Summaries of some of this information are given in this report along with some previously unpublished information.

Jan 1, 1949