Search Documents

By James W. Ballard, H. H. Schrenk

"The X-ray method of quantitative determination is advantageous because it permits determination of compounds rather -than ions or elements; for example, the direct determination of quartz in silicates,4/,5/,6/ The method also takes into account the finest particles of a sample, which may be lost in wet chemical methods because of solubility or in petrographic methods because of limitation of the microscope. The sample is usually reduced to a powder and is easily prepared,7/ only a few milligrams of material being necessary. The sample and its chemical composition are not destroyed and may be used for further analysis by X-ray diffraction or by other methods.This paper presents in detail some of the more essential problems that arise in the application of X-ray diffraction to quantitative chemical analysis, Photometric measurements are discussed in connection with line intensities and the choice of X-ray film. The internal standard method, successfully used in spectrographic analysis, is applied.Copper K-alpha X-rays from a demountable research-type X-ray tube were used with a camera of 20 centimeters radius with a cast-lead-slit collimating system. A combination of a tilted wedge and a lead-slit collimating system permitted irradiation of a large amount of sample with X-rays. This tended to minimize errors due to possible inhonogeneity of the sample, to decrease the time of exposure, and to keep the lines on the X-ray film to a minimum width. There was sufficient dispersion of the lines for satisfactory analysis of most samples. Power was furnished the tube by a. source of constant high potential consisting of a synchronous motor generator furnishing 500-cycle power to a 100-kv. transformer, rectifying valves, and a condenser filter circuit. The X-ray tube was operated as a gas-type tube at 35 kv, and 20 ma,, the exposure times varying from 1 to 2 hours. The constant output of X-rays from the tube, indicated bar an exposure meter built for the purpose, was satisfactory.The recording microphotometer8/has been described. It was found preferable to a nonrecording instrument for measuring blackening of lines above a background on X-ray films. This background, which usually occurs, is sometimes complicated by numerous peaks from lines of complex diffraction patterns. is microphotometer record of the pattern, therefore, facilitates the location of the background 'and the measurement of the heights of the peaks and thus contributes to the accuracy of a determination."

Jun 1, 1946

By Howard C. Turnage, Dana T. Updyke, Wayne C. Muhler

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leaky feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 6, 1980

By Jr. Gabler

World resources of platinum-group metals appear ample for the foreseeable future; however, political and economic events in the last two decades have caused concern over the availability and reliability of an uninterrupted supply. Because of this concern, the U.S. Congress requested that the U.S. Bureau of Mines initiate a study of the flow of platinum-group metals in the economy that would delineate and quantify the production areas in which metal values are lost. As a result, the Bureau has developed a computerized commodity flow model for strategic and critical materials. Major attributes of this flow model are as follows: (1) it is generic and applicable to most commodities and (2) it can be updated as supply, demand, and/or production data change. The original model developed for cobalt, with slight modifications, was used to track the flow of platinum-group metals. This report follows the flow of platinum-group metals through their metallurgical, catalytic, and chemical applications and highlights areas in which significant losses occur because of downgrading, export, or disposal. The study indicates that materials containing about 63,426 kg of platinum-group metals were lost or could not be traced in 1989, representing about 63 pct of U.S. domestic consumption.

Jan 1, 1991

By E. P. Youngman

The basic mining law of French Morocco is the Edict of 1914, "Danir of Jamary 19, 1914, for the Regulation of Mineral Prospecting and Exploitation in the Zone of the French Protectorate of the Cherifien Empire," which, as the preamble states, was promulgated at the instance of the Director General of Public Works, in consideration of the fact that mines constitute one of the sources of wealth of the Empire. According to a consular report, dated May 18, 1923, by Bradford, men- tioned above, the mining industry of that country, aside from the exploitation of the extensive phosphate deposits, can scarcely be said to exist, but the potential field for mining is promising. However, no large-scale exploitation of the mineral wealth of French Morocco can be hoped for until there is complete pacification of large areas that are still in an unsubdued state or until adequate transportation facilities, scientific prospecting, and large investments of cap- ital are assured. An edict in 1920 (Dahir of January 27, 1920) modified the law mentioned above by declaring the prospecting for and the exploitation of phosphates to be exclusively reserved to the Government. The Dahir o. August 7, 1920, announced the creation of the Cherifien Phosphate Office (Office. Cherifien des Phosphates), a State monopoly charged with the exploration, management, and exploitation of the phosphates of Morocco.

May 1, 1930

By B. J. Dalton

Several relationships between coexisting phases for analytical binary solutions near the critical point are given. These relationships were developed from a consideration of a (G u, P) surface at constant temperature and a (G u, T) surface at constant pressure, where G is the molal Gibbs free energy, u is the concentration of component 1 expressed as a mole fraction, G is the pressure, and T is the temperature. These formulas should facilitate the calculation of some of the quantities useful in making thermodynamic consistency checks on phase equilibria data about the critical point.

Jan 1, 1970

By William Catron

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and cuts in the various reining districts of the United States. The mining methods described are those used in the mines of the Cananea Consolidated Copper Co., a Mexico corporation whose holding company in the United States is the Greene Cananea Copper Co. The mines are at Cananea, Sonora, Mexico, 25 miles directly south of the international boundary, approximately in 31° nor to latitude and 110 to 130° west longitude. Cananea is connected with the boundary towns of Naco and Nogales, Ariz., by a standard-gage railroad.

Jan 1, 1930

By Stephen A. Swan

Bureau of Mines research has not included analyses of mining dredge safety since 1948. Because of the increasing use of dredges, 63 fatal accidents and several hundred nonfatal injury accidents involving dredges were examined. Also, 31 working dredges and 3 dredge manufacturers were visited to acquire qualitative information. Drowning accidents represented 59 pct of the fatalities and are delineated in detail. Also, countermeasures against other hazards are discussed.

Jan 1, 1985

By O. C. Blade

This report is one of a series made by the Bureau of Mines under a cooperative agreement with the American Petroleum Institute on the characteristics of commercial aviation gasolines. The series of Surveys is a continuation of like work conducted under aimil.ar cooperative agreements with the Coordinating Research Council, Inc. by the National. Bureau of Standards from 1940 through 1946 and by the Bureau of Mines from 1947 through 1949. A completed list of the series of surveys is given at the end of this paper.

Jan 1, 1951

By Thomas A. Phillips

The Bureau of dines present, an economic evaluation of its process for the ferric chloride leaching of chalcopyrite concentrate. In this process, chalcopyrite concentrate is leached with ferric chloride solution to extract copper, which is precipitated from the solution by electrolysis while leaving sulfur in the residue. Spent liquor from electrolysis is treated with oxygen to regenerate the ferric chloride leach solution and the sulfur-laden residue is processed to recover the sulfur. A cost estimate was prepared for a plant capable of processing 600 tons of chalcopyrite concentrate per day, 330 days per year. The fixed capital cost, on an early 1.975 basis is $27,831,600 and the estimated operating cost is 9.9 cents, per pound of copper product. In comparison, the estimated operating cost of a smelter equipped with a citrate process plant to recover sulfur is about 13.6 cents per pound of copper product. No charge for chalcopyrite concentrate or credit for recovered byproducts has been included in either operating cost. The ferric chloride leach process, therefore, appears to be economically attractive.

Jan 1, 1976

By J. B. Gayle

Both immediate and long-range economic factors are associated with blending anthrafines to produce metallurgical cokes, and they warrant careful consideration of the technology of carbonization of blends containing significant proportions of inert substances in general and anthrafines in particular. This situation has resulted in numerous publications dealing with various phases of the overall problem, particular emphasis being placed on the effects of inert substances on the yields and quality of cokes produced. Because relatively little attention has been given to the expansion behavior of coal blends containing inert substances, an investigation of this problem was undertaken using the Bureau of Mines sole-heated oven. Since experiments in the sole-heated oven do not measure wall pressures directly, a new method of interpretation of sole-heated oven data, which permits estimates of wall pressures, has been proposed.

Jan 1, 1955

By H. P. LeVan

Research was conducted to examine the feasibility of extracting manganese from Georgia umber ore by a three-stage continuous sulfuric acid-ferrous sulfate pickle liquor leaching process. A continuous cyclic process for treating the umber was operated successfully, using a synthetic solution simulating a ferrous sulfate fortified anolyte solution discharged from a manganese electrolytic cell as the leaching medium. Leaching efficiency based on removal of the manganese from the ore ranged from 83 to 89 percent for all systems tested.

Jan 1, 1965

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958

By L. F. Heising

The Bureau of Mines evaluated 42 composite samples from selected Michigan-Wisconsin iron formations by reductive roasting-magnetic separation and flotation at minus 325 mesh. Samples having poor to marginal response on initial examination by conventional methods were reevaluated by finer grinding, by reagent suite modifications, and by selective flocculation-desliming techniques. Results ranged from excellent on Menominee Range samples to relatively on Gogebic Range ores. Marquette Range samples ranged from responsive to nonresponsive, depending upon grain size and mineral association.

Jan 1, 1967

By R. S. Sanford

The Muir Inlet or Nunatak molybdenum deposits arc in the Glacier Bay district, Muir Inlet, miles northwest of Juneau. The deposits were examined by Bureau of Mines engineers, and the area was mapped by a field party of the Federal Geological Survey during the summer of 1942. 5/ The following year the Bureau of Mines began developing the deposits. A total of 217 channel samples were taken, and 2 diamond drill holes totaling 256 feet wore drilled. The samples were sent to the' Bureau's laboratories at Rolla, Mo. for beneficiation.

Jan 1, 1949

By Peter Grandone

Steel and iron pipe lined with cement to protect it against corrosion has been used in the municipal water systems of the New England States since about 1870. In most recent years, the petroleum industry adopted cement-lined pipe to forestall corrosion, particularly in those areas where large quantities of corrosive brines and hydrogen sulfide are associated with the oil produced. Many of the oil companies had on hand large quantities of corroded pipe, normally disposed of as scrap, which could be cleaned, lined with cement, and returned to service. It was soon learned that after the so-called scrap pipe was lined with cement much of it could serve fully as well as new cement-lined pipe. The demand for lining used pipe with cement resulted in the establishment of several processing, plants in the Mid-Continent oil-producing area. Today six cement-lining plants serve the areas three in Oklahoma and one each in Kansas, Texas, and Illinois. All of these plants have lined large quantities of used pipe for the brine-disposal systems of western Kansas, Illinois, and east Texas and also for the operators of water-flooding projects in northeastern Oklahoma and southeastern Kansas, where large quantities of brine and fresh water are being injected into the oil-bearing formations as a secondary oil-recovery method. Since war demands during the past 2 years have created an acute shortage of steel, the need of reclaiming used pipe for the expansion of oil-producing operations has become more evident than ever before. Thus the new industry (about 6 years old) - lining used pipe with cement - is saving large quantities of steel at a critical time by reclaiming used pipe and preventing further- corrosion.

Jan 1, 1945

By J. E. Dooley

A mass spectral scheme of analysis was devised which can be used to identify individually a single compound from a larger group of similar compounds. Mass spectra for 32 alkyl aryl sulfides are provided for future reference work, and analytical correlations used in producing the analytical scheme are discussed. Some of the correlations show that base peaks are either the same mass as the parent peaks or may be derived from cleavage alpha to the sulfur atom with migration of one hydrogen to the sulfur atom. Other spectral consistencies provide means of separating ortho-, meta-, and paratolyl arrangements in an overall analytical scheme. Determinations of chain lengths and separation of isomeric species are also discussed.

Jan 1, 1972

By J. E. Chilton

The Bureau of Mines has examined the operation of an oxygen sensor manufactured by the City University, London, England. The sensor produces a current proportional to the oxygen concentration by reacting oxygen at a nonconsumable cathode. The sensor design is unique in that the primary mode of oxygen transport to the cathode is by diffusion through a capillary, The sensor using this design has a stability of 0- to 0.02-pct reading change per day over a 4.7-month test, small temperature coefficient of 0.29-pct reading change per °C, and small pressure coefficient of 0.34-pct reading change per 1,000-ft altitude change, If this sensor were incorporated into an oxygen detector or monitor, this would be a distinct improvement in electrochemical-type oxygen analyzers and would be useful to the mining industry.

Jan 1, 1983

By P. G. Clites

This study was conducted to determine the patterns of heat transfer to water-cooled copper crucibles during vacuum arc melting. Values of heat flux from the ingot to the crucible were determined during nonconsumable electrode vacuum arc melting of zirconium and during consumable electrode vacuum arc melting of titanium) zirconium) and steel. The results of these studies con-firm the existence of a high thermal resistance between the ingot and the crucible wall which results from the shrinkage of the ingot as the metal solidifies. Maximum heat flux occurs near the top of the ingot where maximum values of heat flux of 1.4 X 106 Btu/ft2 hr were observed during small-scale consumable electrode arc melting of zirconium and titanium. The maximum heat flux for consumable electrode arc melting of 8-inch-diameter ingots was 0.5 X 106 Btu/ft2 hr. The effects of electrode material) electrode diameter) arc current) and arc potential on heat flux from the ingot to the crucible were studied. Data were also obtained on crucible wall temperatures and on the effect of very narrow annular water jackets.

Jan 1, 1967

By C. O. Hawk

As an exploratory effort to produce useful products from coal by a new path, the Bureau has made a few experiments on the fast heating of finely ground coal particles by irradiation with a flash of high intensity light. The flash was produced by an electrical discharge at high voltage through a xenon-filled tube. The flashes lasted from 2 to 3 milliseconds. The reaction took place in small sample tubes, ½ inch-dimeter by 4 inches long, and with small amounts of coal (total amount charged 0.1 gram, probable effective amount not more than 20 milligrams). Average particle size of the coal, estimated on a numerical basis, was 20 microns. Temperatures reached were evidently quite high, because all products obtained in quantity were characteristic of high temperature pyrolysis. Apparently, conversion of the coal was extensive where isolated particles received the full benefit of a flash. It seems particularly significant that acetylene was present in appreciable amounts--comprising almost 3 percent of the total gaseous product in one case. This is good evidence of a short heating period to very high temperature (well above 1,000° C) followed by rapid quenching. Although the results are interesting, they do not suggest any immediate practical application.

Jan 1, 1963

By A. W. Deurbrouck

The Bureau of Mines analyzed 13 samples collected from three Randolph County coalbeds. The Peerless and Sewell bed samples were generally of metallurgical quality as received from the mines or could be easily upgraded. How-ever, the Lower Kittanning coa1bed samples proved to be quite inimical to upgrading to metallurgical quality.

Jan 1, 1966