Search Documents

By D. W. Frommer

As one phase of a general problem of recovering sulfide slimes, mineral-dressing research was conducted on flotation tailing from the St. Joseph Lead Co., Bonne Terre, Mo., mill to recover a significant portion of the residual, finely divided galena. Production of a high-grade concentrate was not part of the immediate objective. Only a reasonable ratio of concentration of lead sulfide slime was sought, since the problem of upgrading by mechanical or extractive processes would be considered in the later stages of this study. The results show that, from a feed material averaging 0.20 percent lead (about 70 percent finer than 400-mesh), a recovery of up to 45 percent could be effected by flotation in rougher concentrate analyzing up to 6.5 percent Pb. These results were obtained by using larger quantities of various xanthates and sodium sulfide than used customarily in mills. Sodium sulfide, which is ordinarily detrimental to flotation of galena, was beneficial in this case.

Jan 1, 1959

By J. Dean Warner

In 1984, as part of a project to evaluate Alaskan occurrences of certain critical and strategic minerals, the Bureau of Mines investigated a columbium-bearing regolith on upper Idaho Gulch, near Tofty, AK. The regolith is derived from weathering of a dolomitic marble and consists mostly of iron oxide minerals with accessory apatite, zircon, xenotime, rutile, monazite, and the columbium minerals aeschynite, columbite, and ilmenorutile. Two regolith lenses contain 340,000 lb of columbium resources at an average grade of 0.07 pct. Calculated composite concentrates from two regolith samples (approximately 200 lb each) contained 53 and 57 pct of the columbium at grades of 0.97 and 0.86 pct, respectively. In each case the grade could be improved to 1.1 pct Cb with a sacrifice of 9-pct recovery. The regolith's mineralogy, trace-element geochemistry, and similarity to descriptions of other columbium-enriched regoliths suggest that the underlying marble may be a carbonatite. The lack of associated alkalic igneous rocks and the stratiform nature of the regolith, however, may be interpreted as evidence for sedimentary origin of the marble. The marble and regolith are a lode source for some of the minerals in the Idaho Gulch placer deposit.

Jan 1, 1986

By John Nagy

Experience and research have shown that an effective way to reduce structural damage from explosions is to provide adequate pressure-relief vents in the walls of equipment and buildings within which explosions might occur. In general, free or unrestricted openings represent the most efficient type of vent. However, in many manufacturing operations it is impractical to use free vents, and it becomes necessary to cover the openings with diaphragms or blow-out disks, hinged panels, or other devices, in order to give protection against weather changes, to prevent the efflux of dusts or vapors from equipment during normal operations, or for other reasons. A few data on the pressure-relieving capacities of hinged panels and a paper diaphragm were published in Bureau of Mines Report of Investigations 3924, which covered the first phase of the dust-explosion venting study made by the Bureau. The present report describes recent experiments that were made to determine the relative effectiveness of an unrestricted vent and 22 types of closures, including various paper, cloth, and metal-foil diaphragms, hinged doors or panels, and several kinds of scored and unscored glass panes. The tests showed that many of the vent closures were effective in releasing the explosions rapidly during their incipient stage, so that the development of destructive pressures was prevented. Vents of this type should prove useful in safeguarding industrial equipment from severe explosion damage. The experiments disclosed that the venting capacities of the diaphragms are approximately inversely proportional to their static bursting strengths.

Jan 1, 1950

By Albert Mendelsohn

This paper, describing the mining practice at the Champion mine of the Copper Range Copper Mining Co., is one of a series of papers on mining methods and costs being prepared by the United States Bureau of Mines. Mining practice at the Champion mine has undergone considerable change during the last four years. Previous to that time the mine was worked by the horizontal out-and-fill method, the stopes starting near the shafts and advancing away from them (fig. 2). The floor pillars were mined by the inclined cut-and-fill method, working en the retreat or toward the shafts (fig. 1). At present the mine is being developed to .tope entirely on the retreat by a sublevel inclined cut-and-fill method.

Jan 1, 1931

By R. V. Ramani, S. Shankar

"Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant (Shankar and Ramani, 1991 ). Therefore, as part of the Respirable Dust Center's ongoing research, the following three-part study was undertaken:• a study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities;• a study of the same in the Lake Lynn Laboratory Mine of the USBM with both air flow and walking by personnel causing re-entrainment; and• the mathematical modeling and computer simulation of the re-entrainment phenomenon.In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory mine are presented. Comparing the results from the two studies,it was observed that increasing the air velocity increased the rate of re-entrainment ( Shankar and Ramani, I 994a) and the rate of re-entrainment decreased with the time of exposure of the source dust to the flowing air. In addition, when the source dust was composed of particles of different sizes, the airborne dust concentrations due to re-entrainment were higher than when the source dust was composed of particles of the same size. The contribution of airborne dust concentration due to air flow was negligible compared to the contribution due to walking. IntroductionIn underground coal mines, dust is produced primarily during the process of mining and during such activities as pillar spall, loading, belt transfer and roof fall. The generated dust is entrained and then collects on surfaces through dispersion, diffusion and eventual deposition. Removal forces, such as flowing ventilation air or turbulence caused by walking and moving vehicles, can re-entrain the deposited dust (Hall, 1955). A portion of the re-entrained dust remains airborne and increases the concentration of airborne dust in mine airways.The presence of airborne coal dust in mine airways in large concentrations can be hazardous. Health effects include coal workers' pneumoconiosis (CWP) and silicosis, and it can be a nuisance affecting visibility. In addition, as is common during methane explosions, if the concentration of airborne coal dust becomes significant, there could be a coal-dust explosion (Singer, Cook and Grumer, 1972; Singer, Harris and Grumer, 1974; Edwards and Ford, 1988). Through concerned research efforts over the last decade, significantprogress has been made in reducing the airborne dust concentration in mine atmospheres. However, secondary sources, such as re-entrainment, have not been studied in-depth. It is important to understand the phenomenon of re-entrainment and its potential contribution to the airborne dust concentration in mine airways for further decreasing airborne dust hazards in mines."

Dec 1, 1996

By Ann Hubbs, Vincent Castranova, Jane Y. C. Ma, De-Hwa Chao, Joseph K. H. Ma

AN OVERVIEW OF THE ACTION OF TETRANDRINE ON SILICOSISBecause of the persistent presence of silica dust in the lungs silicosis is a progressive and irreversible disease. At present, there is no proven effective therapy for silicosis. Limited choices of therapeutic intervention with corticosteroids and other immunosuppressive regimens 1,2 have been accepted for some forms of pulmonary fibrosis. These treatments are only minimally effective, and the results provide little understanding of the disease state due to the lack of correlation between drug activity and the mechanism of fibrosis. Thus, continuing effort must be made in the search for effective antifibrotic agents, which may be used to provide a sequential analysis of the fibrotic process and to open the door for further research and clinical development. Tetrandrine is one of hundreds of drugs screened for antifibrotic activity by Chinese scientists. It has been used in China as a treatment for silicosis in open clinical trials3 and in laboratory animals. The action of tetrandrine on pulmonary fibrosis has been attributed to its ability to inhibit particle stimulation of alveolar macrophages, a key cell type central to the fibrotic process, to release oxygen radicals and inflammatory cytokines. Alveolar macrophages (AM) residing on the alveolar wall, are the predominant phagocytic cells of the lungs responsible for pulmonary defense against inhaled microorganisms and other particles and thus play an important role in maintaining the homeostasis of the lungs. 7 Ample evidence suggests that cells of the monocyte-macrophage series play an important role in the immunopathogenesis of pulmonary fibrosis. When upregulated by silica, alveolar macrophages generate reactive oxygen metabolites8·9 which can damage lung parenchyma and release fibrogenic growth factors and cytokines, 10,11 such as interleukin 1 (IL-1), which can induce fibroblast proliferation and collagen synthesis. The cytokine-mediated fibroblast proliferation and collagen synthesis are key steps in the development and progression of pulmonary fibrosis .11 Previous studies by our group have shown that tetrandrine exhibits strong binding affinity to AM and inhibits particle-stimulated respiratory burst activity (oxygen consumption, superoxide anion release, and hydrogen peroxide secretion) in these cells. 13 In addition, studies by Kang et al. 14 have reported that tetrandrine inhibits silica-induced release of fibrogenic factors such as IL-1 which are capable of inducing fibroblast proliferation and collagen synthesis. Reist et al. 15 further suggested that the antifibrotic action of tetrandrine may be mediated in part by the direct effect of this drug on the ability of fibroblasts to respond to proliferative agents. These results indicate that the mechanism of silicosis involves activation of AM and fibroblasts by silica, resulting in abnormal collagen production due to miscommunications between the cell types. Tetrandrine may interrupt this process by direct interaction with the lung cells.

Jan 1, 1998

By A. L. Murray, C. A. Allen

"The Industrial Commission of Utah from a study of the accidents (especially the fatalities) occurring in connection with mining in the State was struck by the large number arising from lack of due care on the part of the employee injured or carelessness on the part of some fellow employee. Figures show that approximately 40% of the deaths are due to carelessness as against only ) 10% or 12% that can be laid to faulty conditions in the mines. With a view to reducing the number of these accidents an intensive campaign of education was inaugurated, conducted jointly by the Industrial Commission of Utah and the United States Bureau of Mines.Through the cooperation of the U. S. Bureau of Mines, Mine Rescue Car No. 11 operating in Utah has been utilized as the means of carrying on the campaign. In making the regular training visits to the mining camps of Utah the crew of car 11 was authorized to include with the courses of instruction in Mine Rescue and First Aid, safety and health rallies, foremen's safety meetings, and appeals carried on through the public schools to stimulate an awaking of personal responsibility of miners and their familiar' in safety and health endeavor. The work was placed under the direct charge of Dr. Murray who has had previous experience in similar work and brought to the campaign helpful enthusiasm. He was assisted by Bruce Johnson, fore¬man miner of Car 11, who had been safety engineer for the U. S. Smelting Company, and R. W. Clark, first aid miner of Car 11. The expense of providing posters, literature, pledge cars, buttons, rental of special educational films and incidental expenses of foremens' meetings has been born by the Industrial Commission.Plan of the Campaign.In planning the campaign the main object was to revive as much as possible, among the workers, a spirit of responsibility for safety. Any considerable reduction of preventable accidents can be accomplished only through the workers themselves who are responsible for such accidents, therefore, the more personal the application could be made to all the workers the greater the accruing results would be."

May 1, 1921

By Dennis R. Dolinar

Physical property tests were conducted on drill core from three exploratory holes on the Naval Oil Shale Reserve near Anvil Points, Colo. Data and regression analysis curves are presented. Data obtained above the Mahogany zone were used to estimate the potential zone of surface effects from under-ground mining. Single specimen testing was primarily used to obtain Mohr's envelope and subsequent rock properties. The technique is shown to provide satisfactory results for this rock type with a significant reduction of core preparation and testing time.

Jan 1, 1981

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines has shown that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum-group metals (PGM) is technically feasible. The purpose of this work was to investigate the chemistry of the dissolution of PGM in cyanide solutions in more detail. Where possible, samples of pure, elemental PGM powders or foils were used instead of automobile exhaust catalysts, because of their greater purity. Ultraviolet spectra revealed that Pt and Pd were solubilized as the square planar tetracyanometallate (II) complexes, while Rh was solubilized as the octahedral hexacyanorhodate (III) complex. This explained the poor recovery of Rh from solution by carbon adsorption, solvent extraction, and ion exchange observed in earlier research, because of the higher anionic charge and size of the octahedral complex. Leaching rate studies showed that the rate of solubilization was greatest for Pd, followed by Pt and Rh. Although the rate of chemical reaction was the controlling step for the dissolution of elemental Pt and Rh samples, the rate of pore diffusion was rate limiting for PGM in catalyst samples.

Jan 1, 2010

By H. G. Miller

The success of any project in which gas is injected into oil-producing sands to increase the current rate or the economic ultimate production of oil or in which surplus gas from oil-producing operations is stored temporarily in reservoir sands that have been wholly or partly depleted of their producible oil depends mainly upon an understanding of the underground movements of oil, water, and injected gas and the ability to control their speed and direction of migration through the reservoir sends. Many operators believe that injected gas always travels up the structure and drives oil to wells structurally higher than the injection wells, because the specific gravity of the injected gas is less than that of the fluid substances in the formation. Consequently, many injection wells are located on the flanks of oil-bearing structures with the idea of utilizing the energy of the injected gas to drive the oil to producing wells higher on the structure. It is true, under certain conditions of pressure and fluid depletion of the reservoir sands that injected gas will move in an up-structure direction, but the theory that injected gas always moves up the structure is based on an erroneous conception of the laws that pertain to the expansion of gases. By definition, "a gas is distinguished by its property of infinite expansion and is limited in volume only by the walls of the vessel which contains it." The expansion of gas that is injected into reservoir sands also is limited by "walls" that surround the space influenced by the injected gas. The walls of the majority of undrilled or virgin oil-bearing reservoirs in California are the impervious shales overlying and underlying the productive strata and the "dams" or effective barriers of edge water around the rims of the reservoirs. When gas is injected into the sands of a producing reservoir, regardless of the location of the injection well on the structure or the degree of depletion of oil from the sands, one of the walls which confine the gas in the structure about the injection well is fluid. This wall will be edge water in a nearly depleted reservoir, where the drainage cones or regions of reduced pressure about injection and producing wells intersect; and, where there is no interference of drainage cones and the injection well is structurally above the edge water, the wall will be oil. In some producing reservoirs bottom water may be the lower wall of the space that confines the gas about injection wells, but the effect of bottom water on limiting the expansion of gas is the same as if the water was not present and impervious formation separated the producing from the underlying nonproducing strata. Therefore, since compressed gas always seeks regions of reduced pressure and its final volume is limited only by formation and fluid barriers and since the force exerted by the gas under pressure is equal in all directions, the course of migration of injected gas in reservoir sands in California and the effect of the gas pressure on fluid movement does not depend necessarily upon the up-structure location of low-pressure regions.

Jan 1, 1932

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to can and ore rate mines in various foreign countries. This interpretation of the mining laws of the Irish Free State has been prepared from the best available material in Washington and is released subject to amplification and correction, if necessary, by American foreign-service officials. INTRODUCTION This paper is based upon the mines and minerals act, 1931, enacted by the Legislature (Oireachtas) of the Irish Free State (Saorstát Eireann), December 22, 1931, the lull title of which is "An act to establish a board to perform functions in relation to mines and minerals, to authorize the making of lenses of mines and minerals belonging to or vested in Saorstát Eireann, to name provider for facilitating the working of other mines and minerals and, for imposing restrictions on the working of minerals required for the support of buildings and works, to amend the law with respect to mines, and for other purposes incidental to the matters aforesaid.'

Jan 1, 1933

By D. J. Bauer

The Bureau of Mines has conducted extensive studies on the recovery of alumina from kaolinitic clay by a HCI leaching-HCI sparging process. The current study reports a modification of the process, which involves a double-leaching system. The first leach of the calcined clay is made at as high a HCI acid strength as possible so that the dissolution of aluminum chloride hexahydrate (AlCI3*6H20) is suppressed, Most of the impurities, but very little aluminum, are soluble in the strong acid. After liquid-solid separation and washing, the solids are leached with recycled weak HCI, which dissolves the AICI3'6H2O. The pregnant liquor is separated from the gangue, and AICI3'6H2O is crystallized from solu-tion by injecting HCI gas. A proposed flowsheet is presented, and the effect of bleedstream size on AlC13'6H20 purity is discussed.

Jan 1, 1984

By J. A. Herdlick

"INTRODUCTION The BeVan quartz crystal prospect in the Indian Creek mining district of Lemhi County, west-central Idaho, was examined by an engineer of the Bureau of Mines 3/ on July 9, 1943. As quartz crystals possessing peizoelectric properties were on the critical list of strategic war minerals, further exploration of the deposit was recommended. The Bureau of Mines exploration began in December 1943 and continued through January 1944. Additional trenching was completed during May and June 1944. This report presents the data obtained by this exploration.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual exploratoiy work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyses samples and makes beneficiation tests.The quartz crystals found during the exploration were examined and classified at the Bureau of Mines College Park, Md., laboratory and checked at the National Bureau of Standards, Washington, D. C.Fred BeVan, of North Fork, Idaho, and Edward F. Cenis, of the Montana Coal & Iron Company, Spoane, Wash., provided much information on the history and past production of the property."

Mar 1, 1948

By Raja V. Ramani, Wilson Miola

"The potential health effects of quartz-bearing airborne dust in mine and mill atmospheres point to the need for the quantification of quartz content in the source material for determining the source-sink relationships and for choosing applicable control measures. While a standard method exists from a regulatory point of view for the sampling of coal mine atmospheres for determining (i) respirable dust concentrations and (ii) the amount of quartz in the samples, there is no generally accepted standard method for quartz analysis in bulk samples of coal and host rocks. Generally, the bulk sample is reduced to a powder for producing quartz analysis samples. Extensive controls arc necessary to ensure representativeness of the analysis samples when these are very minute fractions of the bulk samples. Since the amount of analysis sample is not limited, alternative methods for quartz analysis may also be tried. It is, however, necessary to adopt a procedure which will satisfy several statistical requirements to guarantee representativeness of the quartz analysis samples.In this paper, the important factors in the preparation of quartz analysis samples from the host rocks and bulk samples are discussed. The method developed to prepare the analysis samples is outlined. The results of application of the procedures are presented. The procedure developed for quartz analysis sample preparation is based on sound statistical foundations. The procedure has been validated for reproducibility and homogeneity.The current methods used for quartz analysis in powders are the P-7 infrared spectrometry and quantitative X-Ray Diffraction (XRD). Both have similar restrictions concerning the sample characteristics and operational problems, which arc intrinsic to radiation beams, device geometry, mechanics and controls of the radiation behavior. Although improvements can be made in the spectrometers and diffractometers, some of the most important steps are the procedures for analysis sample preparation from bulk samples and for calibration of the instruments. The sample preparation process is often referred to as one of grinding and sizing the bulk sample to generate the powder for the scanning devices. The particle sizes are referred to and their influence emphasized but the representativeness of the sample is assumed. Assuring sample representativeness during the sample preparation procedures is critical.For the sampling of airborne respirable dust in coal mines, the collection devices, the collection procedures and the analysis procedures are defined. This is not true for bulk samples where weights must be reduced thousands of times to generate the analysis samples for the scanning devices. The specifications to be developed may include bulk sample amount, sample reduction procedures, sample particle size distribution and sample amounts. However, the common problem of insufficient sample amount which is often encountered with mine airborne dust samples need not exist for bulk samples. Further, the same bulk sample can yield analysis samples for several experiments. The latter, of course, requires sample homogeneity.Three concepts are important in the selection of any procedure for sample preparation and analysis. These arc accuracy, reproducibility and representativeness. The adopted procedure has to guarantee a homogeneous sample representative of the population, a defined level of accuracy and reproducibility. Important statistical concepts are embedded in these requirements, particularly with respect to estimation and dispersion errors. Accuracy and reproducibility are totally different though not independent concepts. Estimation is related to accuracy and the true value. Dispersion is related to reproducibility and is measured by the classical statistical standard deviation of the distribution of a series of measurements or analysis performed over the same lot or analysis sample. The dispersion variance (or dispersion error) does not tell a"

Mar 1, 1992

By C. E. Julihn

In the fall of 1933 a new discovery of gold was made in the old Mojave mining district of California about 70 miles north of Los Angeles. It led to mining operations that have surpassed in their results all reasonable expectations and are of exceptional promise for the future. In less than 3 years, exploration has opened up a number of veins, from some of which a substantial amount of high-grade ore has been shipped, while a large tonnage of milling ore has been disclosed. Two mills, operating on ore averaging better than $12 a ton, will probably produce more than a million dollars worth of gold in 1936, and a considerable increase of their output in the following year is anticipated. While continuance of these operations for a number of years is already assured by ample reserves of ore, future discoveries of still other veins are reasonably possible, as occurrence of gold throughout the volcanic rocks of the district is widespread and the veins now being mined showed little to attract attention at the surface.

Jan 1, 1937

By J. M. Seward, W. D. Dietzman, M. E. Hawkins

Analytical studies of formation waters are widely used by the petroleum industry as an aid in solving problems such as identifying intrusive waters , corrosion studies , treating injection water , and choosing open or closed water- injection systems . The solution of a problem is often simplified when reliable analyses of the waters under consideration have been made previously . Chemical analyses and electrical resistivity measurements are presented on 267 samples from 74 fields in south Arkansas , and 199 samples from 80 fields in north Louisiana .

Jul 1, 1960

By J. W. Town

The Bureau of Mines conducted petrographic classification and flotation studies to determine if acid-grade concentrates could be obtained from individual and composite samples from the Meade Peak member of the Phosphoria Formation, Idaho. The petrographic studies were made to determine the effect of compositional features on concentration of phosphates. The ore grade, ovule size, and clay content were the main features affecting grade and recovery of phosphate. Flotation results on roasted ore with a tall oil emulsion scheme showed that beds containing over 10 percent P2O5 could be beneficiated and composited with the two high-grade beds to produce a composite concentrate containing 31.9 percent 05 at 84.3 percent recovery. Treatment of these intermediate-grade phosphate beds by flotation increased ore reserves over 200 percent and increased the ore-to-waste ratio in the ore zone from 1:5.7 to 1:0.27.

Jan 1, 1966

By Christopher D. Risbrudt

In this comprehensive study of the use of wood products in coal mining, a sample of over 220 mines provided data by questionnaire. Wood use per ton of underground coal was found to vary substantially by mining process and region. In the Eastern Coal region, 1.6 board feet of wood was used per ton of coal, wel above the 0.6 board feet usage per ton in the West. The kind of timber used varied also by Region. Hardwood use is about 40 times greater than softwood in the Eastern Region. There, hardwoods are plentiful, relatively cheap and strong. In the West where softwood forests predominate, softwoods were 2-1/2 times more common in mine wood use than hardwoods. Nearly 80 percent of the wood used in underground coal mines is used in cross bars and props. Nearly 54 million cubic feet of wood products were used in coal mining in the sample year 1979; about twice as much going to underground mines as surface mines. Wood requirements for mining were projected to 2030 for a range of three oil price scenarios. Much greater wood use will be required for greater coal output.

Jan 1, 1982

By G. R. Fitterer, C. H. Herty

"INTRODUCTION Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis in easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot—top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel.For a large tonnage of steels which go into articles manufactured by deep—drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low—carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, — that is to say, deoxidized with manganese and perhaps a small amount of aluminum, — the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper—central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low—carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel."

Feb 1, 1931

By G. S. Scott, G. W. Jones, I. Spolan, R. E. Kennedy

In studies made by the United States Bureau of Mines to determine the causes of explosions in medium-pressure acetylene generators , it was shown that when these are operated at elevated temperatures the acetylene liberated in an acetylene generator carries enough water vapor to heat certain types of carbides to a high temperature , when the acetylene- water vapor mixtures are passed through the carbide . This report contains results of further work carried out to develop an apparatus to show the heating effects or reactivity of various types of carbides in contact with acetylene - water vapor mixtures .

Apr 1, 1947