Search Documents

By M. M. Gilkey

Pegmatites in Colorado occur for 150 miles along the Front Range (eastern-most range of the Rocky Mountains) from Larimer County on the north to Canon City on the south, and west into the Gunnison area. Many of the deposits have been classified. Minerals found in the various dikes include beryl, scrap and possibly punch mica, lithium-bearing minerals, columbite-tantalite, feldspar, and several rare minerals. Pegmatites are abundant in the Crystal Mountain district in Larimer County. About 5 miles south of the Crystal Mountain district and often identified with that district is the Hyatt pegmatite area. The Hyatt Ranch deposit has attracted particular attention because of the comparatively high beryl con-tent of the upper part exposed in opencut workings.

Jan 1, 1960

By Z. J. Fink

Ultraviolet-visible and infrared emission spectra from propagating methane-coal-dust-inhibitor mixtures have been obtained in a 0.2-by 0.2¬by 5.3-m vertical duct over a range of flame speeds from 2 to 100 m/sec. Results serve as a basis for the design and evaluation of thermal radiation detectors for triggered barriers that suppress ongoing mine explosions. Of particular significance is the large continua superimposed on the methane-air spectra when small amounts of coal dust are present and the variation of emissivity with infrared (IR) wavelength in dust flames. In conjunction with the spectral measurements, studies of flame speed, particle size, gas sampling plus thermodynamics, and dust sampling are presented and discussed in order to gain insight into the more fundamental aspects of propagating explosions. Sampling results have shown that only a near-stoichiometric amount of dust is consumed in the flames studied even though initial concentrations are five times stoichiometric. Difficulty in propagating coal-dust inhibitor flames of realistic mine characteristics in a cold-walled laboratory duct has been encountered. A simplified analysis of the flame zone utilizing spectral and sampling results indicates that the stability of slowly propagating flames is more dependent upon thermal radiation than upon convection losses to the walls. It is predicted that thermal radiation losses will make any measurements of coal dust burning velocities, "quenching diameters," or flammability limits more apparatus dependent than those corresponding to gaseous fuels.

Jan 1, 1974

By C. B. Manula

Bituminous coal mining in the United States is currently experiencing a period of rapid growth which began in the early 1960's. Future demands are conservatively predicted to rise to 700 million tons by 1980 and to anywhere between 1 to 3 billion tons by the turn of the century. This means a continuous expansion of coal production by a factor of at least two can be expected before the end of the century. Over the last few years, production from underground mining has decreased; yet it is about 50% of the total coal output. In the absence of any discovery of near surface coal deposits, and even after conceding that some deeper deposits can be surface mined with changes in technology it can be reasonably assumed that coal production from underground will continue to play an important part in solving the energy crisis.

Jan 1, 1975

By Hugh M. Wolfin

This Information Circular is an abstract of a manuscript which was completed in June 1933, by Mr. Hugh M. Wolflin, formerly of the U. S. Bur eau of Mines. This abstract has been prepared by Charles Will Wright for presentation at the February meeting of the American Institute of Mining and Metallurgical Engineers in New York. It has been necessary to omit many of the details and most of the cost data and tables, as well as the illustrations in the original manuscript. As the use of airplanes in mining developments is making such progress and as a publication on this subject to be of greatest value should include the most recent information, it is unfortunate that, due to a lack of printing funds, it has not been possible to publish this manuscript. The purposes of Mr. Wolflin's paper are: (1) To describe briefly what has been accomplished in some outstanding examples by the use of aircraft in the mining and petroleum industries, (2) To record costs, (3) To present available information and suggestions to assist in solving future air-transportation problems in the industries under consideration.

Jan 1, 1934

By R. V. Higgins

The Bureau of Mines investigated the use of electronic computers for obtaining more information about relative permeabilities of reservoir rock to oil and water. It was found that there are many possible combinations of relative permeability curves that will result in virtually the same recovery versus injection) but they require different times and rates to recover the oil even with different mobility ratios. Permeability curves obtained by the use of non-viscous oil and employed for calculating the waterfloods of viscous oils can lead to serious inaccuracies. For viscous oils) the wettability characteristics in the middle portion of the permeability curve affect recovery nearly as much as other portions of the curve; this) however) is not true for non-viscous oils in water-wet reservoir rock.

Jan 1, 1967

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By Wilbert J. Huff

For the past 9 years , the technical studies conducted by the Explosives Division of this Bureau have been summarized in a series of reports issued annually . The following account presents investigations undertaken from July 1 , 1943 , to June 30 , 1944. The work is detailed under a number of main headings corresponding to the organizational structure of the Division , the various activities being under the immediate direction of unit chiefs , who report directly to the author . Specific credit , however , is due to the individual unit leader and his assistants .

Jan 1, 1945

By Suresh K. Bhatt

This U.S. Bureau of Mines report reviews major developments in continuous haulage technology for underground coal mines. Haulage systems, both in use and under development, were investigated through a comprehensive literature search and visits to mines and manufacturers. The systems include flexible conveyor train, mobile conveyor, monorail bridge conveyor, multiple-unit continuous haulage, extensible, and belt turning systems. Strengths and weaknesses of the systems are assessed in light of their operating under remote control and their application to the computer-assisted continuous mining machine research being conducted by the Bureau. Through mining scenarios, candidate haulage systems are conceptualized to be consistent with the capabilities of the mining machine.

Jan 1, 1991

By F. A. Rutledge

[An a part of the United States Department of the interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits of nonmetallic minerals accessible to the Alaska Railroad for use in building; materials is In the Alaska Railroad-belt area. The results of the investigations, to date, indices that raw materials for the preduction of brick products are in plentiful supply as cloy in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.]

Jan 1, 1953

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

By John E. Rourke, O&apos

This report documents the process of site selection, instrument installation, data acquisition, and preliminary data analysis followed to characterize the physical response of overlying strata to longwall mining. A system of surface, subsurface and mine level instrumentation was installed at the Allen Mine in Weston, Colorado where the overburden varied in thickness from 600 to 900 feet. Survey monuments, automatic-recording strain-meters, multi-point rod extensometers, inclinometer-extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. A preliminary analysis of the data acquired up until project termination has shown the system to be operative and strata response to be similar to that reported for other subsidence monitoring case histories. Recommendations for continued monitoring of the instrumentation systems are presented.

Jan 1, 1982

By R. Lincoln

A surplus of vanadium has resulted from the tremendous output of uranium, of which vanadium is a byproduct. More knowledge of the properties and characteristics of vanadium as a pure metal has been needed so that industry can take advantage of its availability and use it according to the best principles of conservation. Besides the problem of utilization, there is the ever present need of finding new materials which will satisfy specific and demanding requirements of science and engineering; vanadium or one of its alloys may possess the latent potential for filling some of these needs. Thus this? research project was undertaken by the Bureau of Mines to determine and examine some of the physical and mechanical properties of pure vanadium. A corallary investigation was the determination of the effect of the interstitial contaminants, oxygen, nitrogen, and carbon, on unalloyed vanadium. The vanadium used for these determinations was principally the product of experimental production of the Bureau. The evaluation of this material, as small quantities became available, provided most of the data that have been obtained.

Jan 1, 1962

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963

By William O. Vanderburg

This paper gives the results of a reconnaissance of the mining districts of Mineral County, Nev., made during the month of June and the first 10 days in October 1936.3/ During the field work virtually all the mining districts in the county were visited and many data were obtained relative to active and inactive properties. The report covers the location of the various mining districts, nature of deposits, ownership, information on past and current activity, data on economic conditions, and general information likely to be useful to operators and investors and others interested in mining. The geology of the deposits is discussed only in a general way. For nearly three-quarters of a century mining tin Mineral County has been the principal if not the only industry of importance. At times it has reached a very low ebb, and at other times it has been attended by the wild excitement that usually accompanies valuable discoveries of precious metals.

Jan 1, 1937

By Carlie E. Banks

Tasks during Phase I of this contract effort were performed in four principal functional areas. These were geology, hydrology, reclamation and mining. Data were gathered from literature reviews, mine visits, survey of manufacturers, consultation with government agencies, and unpublished or private communications with contractors and consultants. The data collected were analyzed for omissions or inaccuracies, then organized into tables, graphs and flow charts to provide a concise body of technical and cost data suitable for the engineering analyses required in Phase II of this contract. Maps illustrating estimated grade and thickness of the oil shale were prepared, some of which are included as exhibits to this report. A preliminary mine layout was performed to test the completeness of the collected data.

Jan 1, 1975

By F. E. Joyce

This paper describes the development of a process for producing manganese and iron pellet concentrates from low-grade manganiferous iron ores of the Cuyuna range by a two-stage sulfatization-reduction roast. First, the manganese minerals (7.5 percent manganese) were converted to water-soluble manganese sulfate by roasting in sulfur oxide gases at 700° C, then, the hematitic iron minerals (31 percent iron) in the hot sulfatized are were reduced to magnetite with simulated reformed natural gas in the temperature range of 350° to 425° C. Batch tests were made in a 3-inch-ID by 6-inch-long, gas-heated, stainless steel retort, and continuous countercurrent experiments were performed in a 2-inch-ID by 10-foot-long, electrically heated shaft furnace. Manganese sulfate was removed from the roasted product by leaching with water, and over 90 percent of the manganese was recovered in an oxide product (65 percent manganese) obtained by precipitation, drying, and thelmal decomposition of the sulfate. An iron oxide concentrate (60 percent iron) with an iron recovery of 75 percent was obtained from the water-insoluble residue by magnetic separation.

Jan 1, 1973

By Francis J. Kelly

This Bureau of Mines study was made to obtain and present facts concerning the production and marketing of rare-earth metals and thorium in the Central and Southern Rocky Mountains (Arizona, Colorado, New Mexico, Utah, and Wyoming, referred to in this report as the region) and to review the current demand for these elements in the United States. Little or no published information was available on the marketing practices for these commodities. As a result of many inquiries from industry, potential prospectors, and the general public, the various factors of resources, production (present and potential), marketing, and consumption have been investigated, and the results are set forth in this report. Material concerning occurrences and deposits is from published references detailed in the bibliography.

Jan 1, 1962

By J. D. Ramsdell

To obtain information on the effects of cobalt on microstructure and tensile properties of titanium-vanadium-cobalt alloys, the composition ranges of 4 to 16 percent vanadium with 1 to 4 percent cobalt have been studied. The beta phase was not completely retained with vanadium additions up to 16 weight-percent or in the same alloys containing up to 4 percent cobalt.

Jan 1, 1960

By Thomas Varley

"The literature on flotation of oxidized ores except for patents (especially for reagents) is very sparse. The Bureau of Mines in 1936, published a circular on the subject, by Ralston and Allen. The treatment of oxides by flotation was then in its infancy, but several of the most important mining companies in the Western United States and Mexico are now operating flotation plants for treating oxidized ores. The purpose of this present circular is to review the progress made and bring the subject up to date. One of the writers of the 1916 report (Mr. Allen) has been associated with some of the most important mining companies who have put into practical operation the process of flotation of oxidized ores; among these companies are the Shhttuck Arizona Copper Co., Bisbee, Arizona (now the Shattuck Denn Co.) and the San Francisco Mines of Mexico, Ltd., San Francisco Del Oro, Chihuahua, Mexico. His experience and other sources of information have been freely drawn on in pre-paring this paper. Mr. Ralston, assistant chief metallurgist of the Bureau of Mines, contributed many valuable suggestions and criticisms.Sulphidizing Reagents for Oxidize Ores.The various reagents and methods that might possibly be used for sulphidizing were summarized by Ralston and Allen as follows:""Sulphidizing (1) by the use of hydrogen sulphide on either the dry or the wet crushed ore, (2) by the use of solutions of the various sulphides and sulpho-compounds of sodium, (3) by the use of solutions of the various sulphides and sulpho-compounds of calcium, (4) by the use of sulphur vapor, (5) by the use of a sulphureted oil, (6) with colloidal sulphur."

Jun 1, 1927

By Margaret R. Egan

A series of experiments were undertaken by the Bureau of Mines to determine the emission products of several types of conveyor belting and other combustible materials found in mines. These experiments were conducted under intermediate-scale, simulated mine conditions to determine smoke characteristics and gas concentrations. From these determinations, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. Three types of belts were investigated: chloroprene, also known as neoprene (NP); polyvinyl chloride (PVC); and styrene-butadiene rubber (SBR). The belts were designated as ignitable or self-extinguishing depending on the length of the burning time and the subsequent combustion products. Under these experimental conditions, the SBR belts were the easiest to ignite. The PVC and NP belts tended to self- extinguish within a few minutes after ignition, but were still capable of maintaining a brief flaming period. These conveyor belt combustion results are compared with previous analyses of wood, transformer fluid, and coal fires. Together they form a data base by which findings from future experiments with other mine combustibles can be compared.

Jan 1, 1988